IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Always request a softreset after hardreset succeeds.
This fixes a regression reported by Martin Michlmayr <tbm@cyrius.com>.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set ATAPI host state machine to control IDE device terminate sequence.
Some IDE harddisk may assert terminate sequence in the middle of a
formal DMA transaction and resume later. Bit DETECT_TERM in ATAPI_CTRL
register determines whether the ATAPI host state machine or the kernel
driver should take care of this case.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A couple of distributions (Fedora, Ubuntu) were having weird problems with the
ATI IXP series PATA controllers being reported as simplex. At the heart of
the problem is that both distros ignored the recommendations to load pata_acpi
and ata_generic *AFTER* specific host drivers.
The underlying cause however is that if you D3 and then D0 an ATI IXP it
helpfully throws away some configuration and won't let you rewrite it.
Add checks to ata_generic and pata_acpi to pin ATIIXP devices. Possibly the
real answer here is to quirk them and pin them, but right now we can't do that
before they've been pcim_enable()'d by a driver.
I'm indebted to David Gero for this. His bug report not only reported the
problem but identified the cause correctly and he had tested the right values
to prove what was going on
[If you backport this for 2.6.24 you will need to pull in the 2.6.25
removal of the bogus WARN_ON() in pcim_enagle]
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: David Gero <davidg@havidave.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_inic162x is now ready for production use. Bump the version,
explain what's working and what's not and drop EXPERIMENTAL.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When attached to cardbus, mmio region is at BAR 1. Other than that,
everything else is the same. Add support for it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_inic162x now doesn't use any SFF features. Remove all SFF
related stuff.
* Mask unsolicited ATA interrupts. This removes our primary source of
spurious interrupts and spurious interrupt handling can be tightened
up. There's no need to clear ATA interrupts by reading status
register either.
* Don't dance with IDMA_CTL_ATA_NIEN and simplify accesses to
IDMA_CTL.
* Inherit from sata_port_ops instead of ata_sff_port_ops.
* Don't initialize or use ioaddr. There's no need to map BAR0-4
anymore.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use IDMA for ATAPI commands. Write and some misc commands time out
when executed using ATAPI_PROT_DMA but ATAPI_PROT_PIO works fine. As
PIO is driven by DMA too, it doesn't make any noticeable difference
for native SATA devices. inic_check_atapi_dma() is implemented to
force PIO for those ATAPI commands.
After this change, sata_inic162x issues all commands using IDMA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use IDMA for PIO and non-data commands. This allows sata_inic162x to
safely drive LBA48 devices. Kill inic_dev_config() which contains
code to reject LBA48 devices.
With this change, status checking in inic_qc_issue() to avoid hard
lock up after hotplug can go away too.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The modified driver on initio site has enough clue on how to use IDMA.
Use IDMA for ATA_PROT_DMA.
* LBA48 now works as long as it uses DMA (LBA48 devices still aren't
allowed as it can destroy data if PIO is used for any reason).
* No need to mask IRQs for read DMAs as IDMA_DONE is properly raised
after transfer to memory is actually completed. There will be some
spurious interrupts but host_intr will handle it correctly and
manipulating port IRQ mask interacts badly with the other port for
some reason, so command type dependent port IRQ masking is not used
anymore.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
inic162x can't reliably read back TF or at least we don't know how to
do it yet. The only values which seem reliable are status and error.
This patch updates access to TF.
* implement inic_tf_read() which reads the TF area in mmio area
* implement custom inic_qc_fill_rtf() which only returns true if
status indicates device error. it'll be returning bogus addresses
for device errors but it'll be able to report why it failed at
least.
* implement custom inic_check_ready() and use ata_wait_after_reset()
instead of the SFF version.
* use inic_tf_read() for classification.
This is not perfect but it fixes hotplug detection failure and at
least makes the driver report 0's instead of random garbages while
reporting valid status and error for device errors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* add a bunch of constants, most are from the datasheet, a few
undocumented ones are from initio's modified driver
* HCTL_PWRDWN is bit 12 not 13
This is in preparation of further inic162x updates.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* use larger indents for structure member definitions
* kill unused variable @addr in inic_scr_write()
* kill unnecessary flushes in inic_freeze/thaw()
* kill buggy explicit kfree() on devres managed port private data
This is in preparation of further inic162x updates.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some tidying as suggested by Grant Grundler.
Nuke local bit-counting function from sata_mv in favour of using hweight16().
Also add a short explanation for the 15msec timeout used when waiting for empty/idle.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Convert sata_mv's EH for FIS-based switching (FBS) over to the
sequence recommended by Marvell. This enables us to catch/analyze
multiple failed links on a port-multiplier when using NCQ.
To do this, we clear the ERR_DEV bit in the EDMA Halt-Conditions register,
so that the EDMA engine doesn't self-disable on the first NCQ error.
Our EH code sets the MV_PP_FLAG_DELAYED_EH flag to prevent new commands
being queued while we await completion of all outstanding NCQ commands
on all links of the failed PM.
The SATA Test Control register tells us which links have failed,
so we must only wait for any other active links to finish up
before we stop the EDMA and run the .error_handler afterward.
The patch also includes skeleton code for handling of non-NCQ FBS operation.
This is more for documentation purposes right now, as that mode is not yet
enabled in sata_mv.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce a new "delayed error handling" mechanism in sata_mv,
to enable us to eventually deal with multiple simultaneous NCQ
failures on a single host link when a PM is present.
This involves a port flag (MV_PP_FLAG_DELAYED_EH) to prevent new
commands being queued, and a pmp bitmap to indicate which pmp links
had NCQ errors.
The new mv_pmp_error_handler() uses those values to invoke
ata_eh_analyze_ncq_error() on each failed link, prior to freezing
the port and passing control to sata_pmp_error_handler().
This is based upon a strategy suggested by Tejun.
For now, we just implement the delayed mechanism.
The next patch in this series will add the multiple-NCQ EH code
to take advantage of it.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Export ata_eh_analyze_ncq_error() for subsequent use by sata_mv,
as suggested by Tejun.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Separate out the inner loop body of mv_host_intr()
into it's own function called mv_port_intr().
This should help maintainabilty.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the unwanted reads of hc_irq_cause from mv_host_intr(),
thereby removing a bug whereby we were not always reading it when needed..
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sigh. Undo some earlier changes to mv_port_intr(),
so that we now read/clear SError again in all cases.
Arrange the top of the function to be as close as possible
to what we need for a later update (in this series) for ERR_DEV handling.
Fix things so that libata-eh can attempt a READ_LOG_EXT_10H
in response to a failed NCQ command, by just doing a local
mv_eh_freeze() rather than ata_port_freeze().
This will now fully handle NCQ errors much of the time,
but more fixes are needed for FBS/PMP, and for certain chip errata.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange mv_config_fbs() to more closely follow the (corrected) datasheet
recommendations for NCQ and FIS-based switching (FBS).
Also, maintain a port flag to let us know when FBS is enabled.
We will make more use of that flag later in this patch series.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part 1 of workaround for errata "sata#25" for the 60x1 series
(the second half of this errata workaround is still in development.
Bit22 of the GPIO port has to be set "on" when in NCQ mode.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The EDMA engine cannot tolerate a mix of NCQ/non-NCQ commands,
and cannot be used for PIO at all. So we need to prevent libata
from trying to feed us such mixtures.
Introduce mv_qc_defer() for this purpose, and use it for all chip versions.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When performing EH, it is recommended to wait for the EDMA engine
to empty out requests-in-progress before disabling EDMA.
Introduce code to poll the EDMA_STATUS register for idle/empty bits
before disabling EDMA. For non-EH operation, this will normally exit
without delay, other than the register read.
A later series of patches may focus on eliminating this and various
other register reads (when possible) throughout the driver,
but for now we're focussing on solid reliablity.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some of the GenIIe EDMA optimizations should not be used
for non-PCI (SOC) devices, and nor for certain configurations
of conventional PCI (non PCI-X, PCIe) buses.
Logic taken/simplified from that in the Marvell proprietary driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
More cosmetic changes; no code changes.
-- try and improve consistency of naming.
-- add missing _OFS to tails of register offset definitions.
-- rename mv_setup_ifctl() to mv_setup_ifcfg(), since that's what it really does.
-- remove/move some dead comments
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On certain configurations (certain macbooks), even though all the
conditions for SIDPR access described in the datasheet are met,
actually reading those registers just returns 0 and have no effect on
write. Verify SIDPR is actually working before enabling it.
This is reported by Ryan Roth in bz#10512.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ryan Roth <ryan.roth@ch2m.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that
the device isn't ready yet. It looks like they use 0xff if device
presence is detected but connection isn't established. 0x77 or 0x7f
after connection is established and use the value from signature FIS
after receiving it.
This patch implements ata_check_ready(), which takes TF status value
and determines whether the port is ready or not considering the above
and other conditions, and use it in @check_ready() functions. This is
safe as both 0x77 and 0x7f aren't valid ready status value even though
they have BSY bit cleared.
This fixes hot plug detection failures which can be triggered with
certain drives if they aren't already spun up when the data connector
is hot plugged.
Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with
eight drives from all major vendors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The discrete VIA ATA chips don't have 0x40 enable bits. We check that
properly in one location but not another. This causes some users 6410
RAID cards to be incorrectly skipped.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use correct variable, achieve desired result...
Spotted by LKML/linux-ide poster whose name I lost (apologies!)
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tidy up naming of things associated with the PCI / SOC chip
"main irq cause/mask" registers, as inspired by Jeff.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Buffer length handling in simulated commands is error-prone and full
of bugs. There are a number of places where necessary length checks
are missing and if the output buffer is passed in as sglist, nothing
works.
This patch adds a static buffer ata_scsi_rbuf which is sufficiently
large to handle the larges output from simulated commands (4k
currently), let all simulte functions write to the buffer and removes
all length checks as we know that there always is enough buffer space.
Copying in (for ATAPI inquiry fix up) and out are handled by
sg_copy_to/from_buffer() behind ata_scsi_rbuf_get/put() interface
which handles sglist properly.
This patch is inspired from buffer length check fix patch from Petr
Vandrovec.
Updated to use sg_copy_to/from_buffer() as suggested by FUJITA
Tomonori.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Petr Vandrovec <petr@vmware.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* make ata_scsiop_*() static
* make ata_scsi_set_sense() static and move it above its users
* make ata_scsi_rbuf_fill() static
* kill unused ata_scsi_badcmd()
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The platform is actually named routerboard 532 so let's call it this. This
patch only rename files, Kconfig and C symbols; no functional changes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When count reaches 0 the postfix decrement still subtracts (to -1),
so bfin_reset_controller() returns as if the busy flag was cleared
while it was not.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Re-enable hotplug, now that the interrupt/error handling are mostly sane.
Also update the TODO list at the top.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Here it is again, minus the checkpatch.pl complaint:
Rework mv_err_intr() to leave the SError bits as-is,
so that libata-eh has a chance to see/use them.
We originally thought that clearing them here was necessary
before writing back to edma_err_cause (per the Marvell datasheets),
but we will end up reseting the chip regardless in those cases.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Continue fixing the interrupt handling logic.
Get rid of mv_intr_pio(), by using ata_sff_host_intr() for PIO..
Add a mv_unexpected_intr() catch-all for "impossible" scenarios,
where we get an interrupt that shouldn't have happened
(never seen in testing, but just in case..).
Rearrange the logic so that we always process completed
response queue entries before looking for other events,
This avoids having to re-issue commands that had already succeeded.
As part of this, we split out some duplicated functionality
into a new function, mv_get_active_qc().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tidy up host controller interrupt handling, by moving the weirdo
bit shifting from mv_interrupt() to mv_host_intr().
This lets us take advantage of the MV_PORT_TO_SHIFT_AND_HARDPORT() macro
from an earlier patch to greatly simplify the port numbering logic.
Also, defer reading the hc_irq_cause (one per hc) until it is
actually proven to be needed. This may save a microsecond or
so per interrupt, on average (a later patchset will further reduce
unnecessary register reads throughout the driver).
Apart from that, we still leave the actual IRQ handling logic alone.
Subsequent patches in this series will address that.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Try and simplify handling of the request/response queues.
Maintain the cached copies of queue indexes in a fully-masked state,
rather than having each use of them have to do the masking.
Split off handling of a single crpb response into a separate function,
to reduce complexity in the main mv_process_crpb_entries() routine.
Ignore the rarely-valid error bits from the crpb status field,
as we already handle that information in mv_err_intr().
For now, preserve the rest of the original logic.
A later patch will deal with fixing that separately.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce the MV_PORT_TO_SHIFT_AND_HARDPORT() macro,
to centralize/simplify various scattered bits of logic
for calculating bit shifts and the like.
Some of the places that do this get it wrong, too,
so consolidating the algorithm at one place will help
keep the code correct.
For now, we use the new macro in mv_eh_{freeze,thaw}.
A subsequent patch will re-use this in the interrupt handlers
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ignore *all* interrupt coalescing bits on all controllers,
not just some of each.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
More cosmetic cleanups prior to the interrupt/error handling logic changes.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The drive is directly soldered to the controller, so there is no cable at
all. Remove the 40-wire assumption so the drive can operate at max speed.
Before patch:
$ dd if=/dev/sda of=/dev/null bs=2M count=64 iflag=direct
134217728 bytes (134 MB) copied, 5.29612 s, 25.3 MB/s
After patch:
$ dd if=/dev/sda of=/dev/null bs=2M count=64 iflag=direct
134217728 bytes (134 MB) copied, 3.94955 s, 34.0 MB/s
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
