IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Now that the Amstrad Delta on-board latches have been converted to GPIO
devices, use the generic driver to control on-board LEDs which hang off
those latches.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Once ready, ams-delta specific device drivers currently calling custom
ams_delta_latch[12]_write() functions can be updated to call generic
gpio_set_value() instead, which will make them less platform dependent.
Even more, some custom ams-delta only drivers can perhaps be dropped
from the tree after converting selected ams-delta platform devices to
follow generic GPIO based device models.
The latch_gpios[] table is initially filled with all latch1 and latch2
GPIO pins in order to register and initialize them from the board file
until those are handled by respective existing device drivers (leds,
nand, lcd, serio, asoc, serial). That table will get almost empty after
the transision process is completed, holding only pins not used by any
drivers / connected to unused devices, in order to initialize them from
the board file for power saving purposes.
The new ams_delta_latch_write() function is a unified replacement for
those removed ams_delta_latch[12]_write(), and serves as a temporary
wrapper over gpio_set_value(), providing the old API for those not yet
updated device drivers, and will be removed after all custom drivers are
converted or replaced.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For still better multi-OMAP1 support, expand omap1_rate_table with flags
for different SoC types and match them while selecting clock rates. The
idea is stolen from current omap24xx clock rate selection algorithm.
Since clkdev platform flag definitions are reused here, those had to be
expanded with one extra entry for OMAP1710 subtype, as this is the only
SoC for which we allow selection of the highest, 216 MHz rate.
Once done, remove no longer needed clock rate configure time options.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit a66cb3454f (ARM: OMAP: Map SRAM
later on with ioremap_exec()) moved the SRAM init to happen later
to remove a dependency to early SoC detection for map_io.
This broke booting on some boards not using Kconfig option for
OMAP_CLOCKS_SET_BY_BOOTLOADER as the dpll1 reprogramming would
cause the following error:
kernel BUG at arch/arm/plat-omap/sram.c:226!
Internal error: Oops - undefined instruction: 0 [#1] PREEMPT
Modules linked in:
CPU: 0 Not tainted (3.2.0-rc1-e3 #9)
PC is at omap_sram_reprogram_clock+0x28/0x30
LR is at omap1_select_table_rate+0x88/0xb4
pc : [<c001b0c4>] lr : [<c0019f54>] psr: 600000d3
sp : c035bf10 ip : c035bf20 fp : c035bf1c
r10: c035bfd4 r9 : 54029252 r8 : c03f8120
r7 : c0362b50 r6 : 00b71b00 r5 : c03873cc r4 : c0362b40
r3 : 00000000 r2 : c0362b40 r1 : 0000010a r0 : 00002cb0
Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel
Control: 0000317f Table: 10004000 DAC: 00000017
Process swapper (pid: 0, stack limit = 0xc035a270)
Stack: (0xc035bf10 to 0xc035c000)
bf00: c035bf3c c035bf20 c0019f54 c001b0ac
bf20: 00001000 00002cb3 00000004 c035ed4c c035bf74 c035bf40 c033ea24 c0019edc
bf40: c02f526c 00000002 00000015 bc058c9b 93111a16 c035335c 02000000 c035ed4c
bf60: c035ed4c c03f8120 c035bf84 c035bf78 c00194c4 c033e8ec c035bfc4 c035bf88
bf80: c033bc24 c00194a0 c035bf90 c035bf98 00000000 00000000 00000000 00000000
bfa0: 00000001 00000000 c0354678 c035ece4 10004000 103532f4 c035bff4 c035bfc8
bfc0: c0338574 c033b598 00000000 00000000 00000000 c035467c 0000317d c035c03c
bfe0: c0354678 c035ece4 00000000 c035bff8 10008040 c0338508 00000000 00000000
Backtrace:
[<c001b09c>] (omap_sram_reprogram_clock+0x0/0x30) from [<c0019f54>] (omap1_select_table_rate+0x88/0xb4)
[<c0019ecc>] (omap1_select_table_rate+0x0/0xb4) from [<c033ea24>] (omap1_clk_init+0x148/0x334)
r7:c035ed4c r6:00000004 r5:00002cb3 r4:00001000
[<c033e8dc>] (omap1_clk_init+0x0/0x334) from [<c00194c4>] (omap1_init_early+0x34/0x48)
r8:c03f8120 r7:c035ed4c r6:c035ed4c r5:02000000 r4:c035335c
[<c0019490>] (omap1_init_early+0x0/0x48) from [<c033bc24>] (setup_arch+0x69c/0x79c)
[<c033b588>] (setup_arch+0x0/0x79c) from [<c0338574>] (start_kernel+0x7c/0x2f4)
[<c03384f8>] (start_kernel+0x0/0x2f4) from [<10008040>] (0x10008040)
r7:c035ece4 r6:c0354678 r5:c035c03c r4:0000317d
Code: 0a000002 e1a0e00f e12fff13 e89da800 (e7f001f2)
Fix this by adding omap1_clk_late_init() that only reprograms dpll1
if the bootloader rate is less than 60MHz. This also allows removing
of the OMAP_CLOCKS_SET_BY_BOOTLOADER option.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For omap15xx and 730 we need to use the MPU timer
as the 32K timer is not available. For omap16xx
we want to use the 32K timer because of PM. Fix this
by allowing to build in both timers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patches removes a config option that was used to select a FIQ
handler to be build for Amstrad Delta, as required by the on-board serio
interface driver. Not having any problem reports received since it was
introduced in 2.6.35, the FIQ handler can now be built and initialized by
default, thus reqiring no extra config option.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch below updates broken web addresses in the arch directory.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add KConfig entry for one of the OMAP1 DVFS rates that was missing it.
Based on the surrounding rate KConfigs and the oscillator frequency,
this patch marks it as valid for all OMAP1 platforms -- Richard,
Tuukka, Tony, perhaps you can comment if this does not look right?
In the long term, all of these CONFIG_OMAP_ARM_*MHZ should be removed.
The OPP settings should be associated with the platform information in
the structure data (perhaps by extending the omap_chip defines). The
selection of which rates to use should be handled at runtime; rates
that are impossible due to xtal frequency mismatch or SoC-type
mismatch should not be included. If implemented correctly, this
should save some CPU time and some memory on OMAP1 kernels.
Reported-by: Christoph Egger <siccegge@cs.fau.de>
Reported-by: The VAMOS Research Project <vamos@i4.informatik.uni-erlangen.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Tuukka Tikkanen <tuukka.tikkanen@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch introduces a Fast Interrupt Request (FIQ) handler for Amstrad Delta
(E3) videophone. The handler's purpose is to process interrupts generated by a
GPIO line that a serial keyboard clock hangs off. It collects consecutive bits
into words, pushing them into a buffer, then requests a higher level interrupt
after one or more words are ready for further processing by a keyboard port
driver.
The handler also processes interrupts generated by two other GPIO lines, used
by other on-board supported devices, by simply requesting a higher level
interrupt, that in turn should invoke those device's specific irq handlers.
IRQ12 line, not used by OMAP1510 hardware (described as reserved), has been
choosen as a higher level interrupt source.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch introduces support for the HTC Herald (T-Mobile
Wing, etc.) series of smart phones -- board support and LCD
panel settings.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The l3_ocpi_ck clock is needed on omap7xx processors for USB.
Additionally, bit 8 of the SOFT_REQ_REG needs to be enabled for
the usb_dc_ck on omap7xx, which is a different bit than that
of the omap16xx-defined clock of the same name.
I added a provision for the usb_dc_ck and l3_ocpi_ck clocks as
dc_clk and hhc_clk, respectively, for omap7xx CPUs. Additionally,
I added a check in machine_without_vbus_sense for all omap7xx
devices, as presently I know of no omap7xx-based devices that
have vbus sense, and it made more sense to me to use a cpu check
here than to spell out each machine one at a time. Finally, DMA
is disabled for omap7xx, as it causes problems with these chips.
Cc: linux-usb@vger.kernel.org
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rather than:
config CPU_BLAH
bool
depends on ARCH_FOO || MACH_BAR
default y if ARCH_FOO || MACH_BAR
arrange for ARCH_FOO and MACH_BAR to select CPU_BLAH directly.
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Brian Swetland <swetland@google.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds basic support for Siemens SX1. More patches are available,
with video driver, mixer, and serial ports working. That is enough to
do gsm calls with right userland.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds board file and necessary includes for Palm Tungsten|T.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/mach-omap1/Kconfig:41:warning: 'select' used by config
symbol 'MACH_OMAP_H3' refers to undefined symbol 'GPIOEXPANDER_OMAP'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mostly cosmetic to sync up with linux-omap tree
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix various typos in kernel docs and Kconfigs, 2.6.21-rc4.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch syncs omap specific core code with linux-omap.
Most of the changes are needed to fix bitrot caused by
driver updates in linux-omap tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
More fixes to build breakage from the work_struct changes ... this updates
the tps65010 driver. Plus, fix some dependencies related to the way it's
used on the OMAP OSK: force static linking there, since the resulting
kernel can't link.
NOTE that until the i2c core gets fixed to work without SMBUS_QUICK,
kernels needing this driver must still use "tps65010.force=0,0x48" on the
command line.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds core support for the TI F-Sample Board (OMAP 850).
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch from Tony Lindgren
This patch syncs OMAP board support with linux-omap tree.
The highlights of the patch are:
- Add support for Nokia 770 by Juha Yrjola
- Add support for Samsung Apollon by Kyungmin Park
- Add support for Amstrad E3 videophone by Jonathan McDowell
- Remove board-netstar.c board support as requested by Ladislav Michl
- Do platform_device registration in board files by Komal Shah et al.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Omap1 serial pport and framebuffer init updates by Imre Deak
- Add support for omap310 processor and Palm Tungsten E PDA
by Laurent Gonzales, Romain Goyet, et al. Omap310 and
omap1510 processors are now handled as omap15xx.
- Omap1 specific changes to shared omap clock framework
by Tony Lindgren
- Omap1 specific changes to shared omap pin mux framework
by Tony Lindgren
- Other misc fixes, such as update memory timings for smc91x,
omap1 specific device initialization etc.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Convert more drivers to register resources in board-*.c to take
advantage of the driver model by David Brownell and Ladislav Michl
- Use set_irq_type() for GPIO interrupts instead of
omap_set_gpio_edge_ctrl() by David Brownell
- Add minimal support for handling optional add-on boards, such as
OSK Mistral board with LCD and keypad, by David Brownell
- Minimal support for loading functions to SRAM by Tony Lindgren
- Wake up from serial port by muxing RX lines temporarily into GPIO
interrupts by Tony Lindgren
- 32KHz sched_clock by Tony Lindgren and Juha Yrjola
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch by Paul Mundt and other OMAP developers modifies
ARM specific Kconfig to allow sharing code between OMAP1 and
OMAP2 architectures.
In order to share code between OMAP1 and OMAP2, all OMAP1
specific code is moved into mach-omap1 directory in the
following patch. A new mach-omap2 directory will be added
later on.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
