IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The event log is an optional firmware feature, if the firmware
does not support it then the securityfs files should not be created
and no other notification given.
- Uniformly return -ENODEV from the tpm_bios_log_setup cone if
no event log is detected.
- Check in ACPI if this node was discovered via ACPI.
- Improve the check in OF to make sure there is a parent and to
fail detection if the two log properties are not declared
- Pass through all other error codes instead of filtering just some
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Check the bios_dir entry for NULL before accessing it. Currently
this crashes the driver when a TPM 2 is attached and the entries
are NULL.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
device_node np contains a garbage value from the stack and it
is only set if chip->dev.parent->of_node is not null. Thus the
check for a null np won't spot a garbage value of np from the
stack if chip->dev.parent->of_node is null and if np contains
an garbage non-null value.
I believe the correct fix is to return -ENODEV if and only if
chip->dev.parent->of_node is null.
Found with static analysis by CoverityScan, CID 1377755
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This patch removes the unnecessary error messages on failing to
allocate memory and replaces pr_err/printk with dev_dbg/dev_info
as applicable.
Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Using the device of_node property is a better way to refer to the
device tree node rather than of_find_node_by_name().
Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Currently, read_log() has two implementations: one for ACPI platforms
and the other for device tree(OF) based platforms. The proper one is
selected at compile time using Kconfig and #ifdef in the Makefile,
which is not the recommended approach.
This patch removes the #ifdef in the Makefile by defining a single
read_log() method, which checks for ACPI/OF event log properties at
runtime.
[jarkko.sakkinen@linux.intel.com: added tpm_ prefix to read_log*]
Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This patch fixes the missing .owner field in
tpm_bios_measurements_ops definition.
Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Move the backing memory for the event log into tpm_chip and push
the tpm_chip into read_log. This optimizes read_log processing by
only doing it once and prepares things for the next patches in the
series which require the tpm_chip to locate the event log via
ACPI and OF handles instead of searching.
This is straightfoward except for the issue of passing a kref through
i_private with securityfs. Since securityfs_remove does not have any
removal fencing like sysfs we use the inode lock to safely get a
kref on the tpm_chip.
Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Check for TPM2 chip in tpm_sysfs_add_device, tpm_bios_log_setup and
tpm_bios_log_teardown in order to make code flow cleaner and to enable
to implement TPM 2.0 support later on. This is partially derived from
the commit by Nayna Jain with the extension that also tpm1_chip_register
is dropped.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Nayna Jain <nayna@linux.vnet.ibm.com>
This commit is based on a commit by Nayna Jain. Replaced dynamically
allocated bios_dir with a static array as the size is always constant.
Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
checkpatch.pl flags warning for symbolic permissions and suggests
to replace with octal value.
This patch changes securityfs pseudo files permission
to octal values in tpm_bios_log_setup().
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This provides an open firwmare driver binding for tpm_tis. OF
is useful on arches where ACPI/PNP is not used.
The tcg,tpm-tis-mmio register map interface is specified by the TCG.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Added kdoc comments for VTPM_PROXY_IOC_NEW_DEV so that these can be
imported to the kernel documentation written with rst markup and
generated with Sphinx.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Only call pm_runtime_get_sync if the device has a parent. This
change fixes a crash in the tpm_vtpm_proxy driver since that
driver does not have a parent device.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
open() method for event log ascii and binary bios measurements file
operations are very similar. This patch refactors the code into a
single open() call by passing seq_operations as i_node->private data.
Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This is no longer necessary, all calls to tpm_chip_unregister happen
in remove() callbacks.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
tpm_chip_unregister can only be called after tpm_chip_register.
devm manages the allocation so no unwind is needed here.
Cc: stable@vger.kernel.org
Fixes: afb5abc262 ("tpm: two-phase chip management functions")
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The tis driver does a tpm_get_timeouts out side of tpm_chip_register,
and tpm_get_timeouts can print a message, resulting in two prints, eg:
tpm tpm0: [Hardware Error]: Adjusting reported timeouts: A 10000->750000us B 10000->2000000us C 10000->750000us D 10000->750000us
Keep track and prevent tpm_get_timeouts from running a second time, and
clarify the purpose of the call in tpm_tis_core to only be connected to
irq testing.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
If the TPM we're connecting to uses a static burst count, it will report
a burst count of zero throughout the response read. However, get_burstcount
assumes that a response of zero indicates that the TPM is not ready to
receive more data. In this case, it returns a negative error code, which
is passed on to tpm_tis_{write,read}_bytes as a u16, causing
them to read/write far too many bytes.
This patch checks for negative return codes and bails out from recv_data
and tpm_tis_send_data.
Cc: stable@vger.kernel.org
Fixes: 1107d065fd (tpm_tis: Introduce intermediate layer for TPM access)
Signed-off-by: Josh Zimmerman <joshz@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Place kdoc just above tpm_pcr_extend so it can be parsed correctly.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Use cpu_to_b32 at the time it is needed in enum tpm_capabilities and
enum tpm_sub_capabilities in order to be consistent with the other
enums in drivats/char/tpm/tpm.h.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Call tpm_getcap() from tpm_get_timeouts() to eliminate redundant
code. Return all errors to the caller rather than swallowing them
(e.g. when tpm_transmit_cmd() returns nonzero).
Signed-off-by: Ed Swierk <eswierk@skyportsystems.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
In some weird cases it might be possible that the TPM does not set
STS.VALID within the given timeout time (or ever) but sets STS.EXPECT
(STS=0x0C) In this case the driver gets stuck in the while loop of
tpm_tis_send_data and loops endlessly.
Checking the return value of wait_for_tpm_stat fixes this and the driver
bails out correctly. While at it fixing all other users since if the
TPM does not manage to set STS.VALID within the reasonable timeframe
something is definitely wrong and the driver should react correctly.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Utilize runtime_pm for driving tpm crb idle states.
The framework calls cmd_ready from the pm_runtime_resume handler
and go idle from the pm_runtime_suspend handler.
The TPM framework should wake the device before transmit and receive.
In case the runtime_pm framework is not compiled in or enabled, the device
will be in the permanent ready state.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This is preparation step for implementing tpm crb
runtime pm. We need to have tpm chip allocated
and populated before we access the runtime handlers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
There is a HW bug in Skylake, and Broxton PCH Intel PTT device, where
most of the registers in the control area except START, REQUEST, CANCEL,
and LOC_CTRL lost retention when the device is in the idle state. Hence
we need to bring the device to ready state before accessing the other
registers. The fix brings device to ready state before trying to read
command and response buffer addresses in order to remap the for access.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The register TPM_CRB_CTRL_REQ_x contains bits goIdle and cmdReady for
SW to indicate that the device can enter or should exit the idle state.
The legacy ACPI-start (SMI + DMA) based devices do not support these
bits and the idle state management is not exposed to the host SW.
Thus, this functionality only is enabled only for a CRB start (MMIO)
based devices.
Based on Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
original patch:
'tpm_crb: implement power tpm crb power management'
To keep the implementation local to the hw we don't use wait_for_tpm_stat
for polling the TPM_CRB_CTRL_REQ.
[jarkko.sakkinen@linux.intel.com: removed cmdReady debug trace on a
success case due the heavy amount of log traffic it causes.]
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Use xenbus_read_unsigned() instead of xenbus_scanf() when possible.
This requires to change the type of one read from int to unsigned,
but this case has been wrong before: negative values are not allowed
for the modified case.
Cc: peterhuewe@gmx.de
Cc: tpmdd@selhorst.net
Cc: jarkko.sakkinen@linux.intel.com
Cc: jgunthorpe@obsidianresearch.com
Cc: tpmdd-devel@lists.sourceforge.net
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Removal of this check was not properly amended to the original commit.
Cc: stable@vger.kernel.org
Fixes: 0c54133223 ("tpm: use tpm_pcr_read_dev() in tpm_do_selftest()")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Utilize runtime_pm for driving tpm crb idle states.
The framework calls cmd_ready from the pm_runtime_resume handler
and go idle from the pm_runtime_suspend handler.
The TPM framework should wake the device before transmit and receive.
In case the runtime_pm framework is not enabled, the device will be in
ready state.
[jarkko.sakkinen@linux.intel.com: changed pm_runtime_put_sync()
to pm_runtime_put()]
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This is preparation step for implementing tpm crb
runtime pm. We need to have tpm chip allocated
and populated before we access the runtime handlers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
There is a HW bug in Skylake, and Broxton PCH Intel PTT device, where
most of the registers in the control area except START, REQUEST, CANCEL,
and LOC_CTRL lost retention when the device is in the idle state. Hence
we need to bring the device to ready state before accessing the other
registers. The fix brings device to ready state before trying to read
command and response buffer addresses in order to remap the for access.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
The register TPM_CRB_CTRL_REQ_x contains bits goIdle and cmdReady for
SW to indicate that the device can enter or should exit the idle state.
The legacy ACPI-start (SMI + DMA) based devices do not support these
bits and the idle state management is not exposed to the host SW.
Thus, this functionality only is enabled only for a CRB start (MMIO)
based devices.
Based on Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
original patch:
'tpm_crb: implement power tpm crb power management'
To keep the implementation local to the hw we don't use wait_for_tpm_stat
for polling the TPM_CRB_CTRL_REQ.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
tpm_transmit() does not check that bufsiz is at least TPM_HEADER_SIZE
before accessing data. This commit adds this check and returns -EINVAL
if it fails.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Constify TPM 1.x header structures in order to move them to rodata
section as they are meant to be never changed during runtime.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Because of the line break in the debug print the chackpatch is
not silent on 80 characters limitation.
The easiest fix is to straighten the lines, it's also more readable.
WARNING: line over 80 characters
+ FW_BUG "TPM2 ACPI table does not define a memory
resource\n");
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Don't apply endianity conversion when writing to the registers
this is already handled by the system.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Instead of expensive register access on retrieving cmd_size
on each send, save the value during initialization in the private
context. The value doesn't change.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The platform device is not used in this driver, drop the
include to linux/platform_device.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fixes the warning:
drivers/char/tpm/tpm_tis_core.c:443:7: warning: variable ‘itpm’ set but
not used [-Wunused-but-set-variable]
bool itpm;
^~~~
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Renamed CRB protocol specific constants to match the TCG PC Client
Platform TPM Profile (PTP) Specification and driver status constants
to be explicit that they are driver specific.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The req_canceled() callback is used by tpm_transmit() periodically to
check whether the request has been canceled while it is receiving a
response from the TPM.
The TPM_CRB_CTRL_CANCEL register was cleared already in the crb_cancel
callback, which has two consequences:
* Cancel might not happen.
* req_canceled() always returns zero.
A better place to clear the register is when starting to send a new
command. The behavior of TPM_CRB_CTRL_CANCEL is described in the
section 5.5.3.6 of the PTP specification.
CC: stable@vger.kernel.org
Fixes: 30fc8d138e ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Instead of a ad-hoc protocol message construction it is better to
call tpm_pcr_read_dev().
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
It is better to tpm_transmit_cmd() in tpm2_probe() in order to get
consistent command handling throughout the subsystem.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Since tpm_gen_interrupt() is only used in tpm_tis_core.c this commit
replaces it with an internal tpm_tis_gen_interrupt(). The semantics
also changed in a way that on a system error the driver initialization
is failed.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Removed unnecessary externs from tpm.h.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
This function should only be called as part of an IRQ probing protocol
and st33 does not have any code to detect that the IRQ it tries to
generate was not generated and disable the IRQ.
Since st33 is primarily a DT binding driver it should not be doing
IRQ probing anyhow, so let us just delete this useless call.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Unseal and load operations should be done as an atomic operation. This
commit introduces unlocked tpm_transmit() so that tpm2_unseal_trusted()
can do the locking by itself.
Fixes: 0fe5480303 ("keys, trusted: seal/unseal with TPM 2.0 chips")
Cc: stable@vger.kernel.org
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
The driver emits invalid self test error message even though the init
succeeds.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fixes: cae8b441fc ("tpm: Factor out common startup code")
Reviewed-by: James Morris <james.l.morris@oracle.com>
The command flow is exactly the same, the core simply needs to be
told to enable TPM2 mode when the compatible string indicates a
TPM2.
Signed-off-by: Andrew Azmansky <andrew.zamansky@nuvoton.com>
Tested-by: Andrew Zamansky <andrew.zamansky@nuvoton.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The TCG standard startup sequence (get timeouts, tpm startup, etc) for
TPM and TPM2 chips is being open coded in many drivers, move it into
the core code.
tpm_tis and tpm_crb are used as the basis for the core code
implementation and the easy drivers are converted. In the process
several small drivers bugs relating to error handling this flow
are fixed.
For now the flag TPM_OPS_AUTO_STARTUP is optional to allow a staged
driver roll out, but ultimately all drivers should use this flow and
the flag removed. Some drivers still do not implement the startup
sequence at all and will need to be tested with it enabled.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Andrew Zamansky <andrew.zamansky@nuvoton.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
If devm_add_action() fails we are explicitly calling put_device() to
free the resources allocated. Lets use the helper
devm_add_action_or_reset() and return directly in case of error, as we
know that the cleanup function has been already called by the helper if
there was any error.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
In 570a3609 IRQ path is incorrectly always exercised while it should be
exercised only when there is an IRQ number allocated. This commit
reverts the old behavior.
[jarkko.sakkinen@linux.intel.com: updated description]
Fixes: 570a36097f ("tpm: drop 'irq' from struct tpm_vendor_specific")
Signed-off-by: Andrew Zamansky <andrew.zamansky@nuvoton.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Some chips incorrectly support partial reads from TPM_STS register
at non-zero offsets. Read the entire 32-bits register instead of
making two 8-bit reads to support such devices and reduce the number
of bus transactions when obtaining the burstcount from TPM_STS.
Fixes: 27084efee0 ("tpm: driver for next generation TPM chips")
Signed-off-by: Andrey Pronin <apronin@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The result must be converted from BE byte order, which is used by the
TPM2 protocol. This has not popped out because tpm2_get_tpm_pt() has
been only used for probing.
Fixes: 7a1d7e6dd7 ("tpm: TPM 2.0 baseline support")
Change-Id: I7d71cd379b1a3b7659d20a1b6008216762596590
Signed-off-by: Andrey Pronin <apronin@chromium.org>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
tpm_tis_core was missing conversion from msec when assigning max
timeouts from constants.
Fixes: aec04cbdf7 ("tpm: TPM 2.0 FIFO Interface")
Signed-off-by: Andrey Pronin <apronin@chromium.org>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Spi protocol standardized by the TCG is now supported by most of TPM
vendors.
It supports SPI Bit Protocol as describe in the TCG PTP
specification (chapter 6.4.6 SPI Bit Protocol).
Irq mode is not supported.
This commit is based on the initial work by Peter Huewe.
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
To avoid code duplication between the old tpm_tis and the new and future
native tcg tis driver(ie: spi, i2c...), the tpm_tis driver was reworked,
so that all common logic is extracted and can be reused from all drivers.
The core methods can also be used from other TIS like drivers.
itpm workaround is now managed with a specific tis flag
TPM_TIS_ITPM_POSSIBLE.
This commit is based on the initial work by Peter Huewe.
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This splits tpm_tis in a high-level protocol part and a low-level interface
for the actual TPM communication. The low-level interface can then be
implemented by additional drivers to provide access to TPMs using other
mechanisms, for example native I2C or SPI transfers, while still reusing
the same TIS protocol implementation.
Though the ioread/iowrite calls cannot fail, other implementations of this
interface might want to return error codes if their communication fails.
This follows the usual pattern of negative values representing errors and
zero representing success. Positive values are not used (yet).
Errors are passed back to the caller if possible. If the interface of a
function does not allow that, it tries to do the most sensible thing it
can, but this might also mean ignoring the error in this instance.
This commit is based on the initial work by Peter Huewe.
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Split priv_data structure in common and phy specific structures. This will
allow in future patches to reuse the same tis logic on top of new phy such
as spi and i2c. Ultimately, other drivers may reuse this tis logic.
(e.g: st33zp24...)
iobase field is specific to TPM addressed on 0xFED4xxxx on LPC/SPI bus.
This commit is based on the initial work by Peter Huewe.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Add missing include guards in tpm.h
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fix the suspend regression due to the wrong way of retrieving the
chip structure. The suspend functions are attached to the hardware
device, not the chip and thus must rely on drvdata.
Fixes: e89f8b1ade9cc1a ("tpm: Remove all uses of drvdata from the TPM Core")
Reported-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Fixes: 28157164b056 ("tpm: Remove useless priv field in struct tpm_vendor_specific")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The newly added vtpmx driver fails to build if CONFIG_ANON_INODES
is disabled:
drivers/char/built-in.o: In function `vtpmx_fops_ioctl':
(.text+0x97f8): undefined reference to `anon_inode_getfile'
This adds a Kconfig 'select' statement to ensure it's always there
when we need it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 794c38e01358 ("tpm: Proxy driver for supporting multiple emulated TPMs")
Acked-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The devm for the IRQ was placed on the chip, not the pdev. This can
cause the irq to be still callable after the pdev has been cleaned up
(eg priv kfree'd).
Found by CONFIG_DEBUG_SHIRQ=y
Reported-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Fixes: 233a065e0cd0 ("tpm: Get rid of chip->pdev")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This patch implements a proxy driver for supporting multiple emulated TPMs
in a system.
The driver implements a device /dev/vtpmx that is used to created
a client device pair /dev/tpmX (e.g., /dev/tpm10) and a server side that
is accessed using a file descriptor returned by an ioctl.
The device /dev/tpmX is the usual TPM device created by the core TPM
driver. Applications or kernel subsystems can send TPM commands to it
and the corresponding server-side file descriptor receives these
commands and delivers them to an emulated TPM.
The driver retrievs the TPM 1.2 durations and timeouts. Since this requires
the startup of the TPM, we send a startup for TPM 1.2 as well as TPM 2.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
CC: linux-kernel@vger.kernel.org
CC: linux-doc@vger.kernel.org
CC: linux-api@vger.kernel.org
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Introduce TPM_CHIP_FLAG_VIRTUAL to be used when the chip device has no
parent device.
Prevent sysfs entries requiring a parent device from being created.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The final thing preventing this was the way the sysfs files were
attached to the pdev. Follow the approach developed for ppi and move
the sysfs files to the chip->dev with symlinks from the pdev
for compatibility. Everything in the core now sanely uses container_of
to get the chip.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Remove useless priv field in struct tpm_vendor_specific and take benefit
of chip->dev.driver_data. As priv is the latest field available in
struct tpm_vendor_specific, remove any reference to that structure.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Move tpm_vendor_specific data related to TCG PTP specification to tpm_chip.
Move all fields directly linked with well known TCG concepts and used in
TPM drivers (tpm_i2c_atmel, tpm_i2c_infineon, tpm_i2c_nuvoton, tpm_tis
and xen-tpmfront) as well as in TPM core files (tpm-sysfs, tpm-interface
and tpm2-cmd) in tpm_chip.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Dropped the field 'locality' from struct tpm_vendor_specific migrated it to
the private structures of st33zp24, tpm_i2c_infineon and tpm_tis.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Dropped the field 'read_queue' from struct tpm_vendor_specific and make it
available to the various private structures in the drivers.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Dropped the field 'irq' from struct tpm_vendor_specific and make it
available to the various private structures in the drivers using irqs.
A dedicated flag TPM_CHIP_FLAG_IRQ is added for the upper layers.
In st33zp24, struct st33zp24_dev declaration is moved to st33zp24.h in
order to make accessible irq from other phy's(i2c, spi).
In tpm_i2c_nuvoton, chip->vendor.priv is not directly allocated. We can
access irq field from priv_data in a cleaner way.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Dropped the field 'iobase' from struct tpm_vendor_specific and migrated
it to the private structures of tpm_atmel and tpm_tis.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Dropped list from struct tpm_vendor_specific as it is not used in any
place.
It is initialized in tpm_i2c_infineon but not used at all in the code.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Removed the field because it is not used for anything.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Dropped the field 'base' from struct tpm_vendor_specific and migrated
it to the private structures of tpm_atmel and tpm_nsc.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Dropped manufacturer_id from struct tpm_vendor_specific and redeclared
it in the private struct priv_data that tpm_tis uses because the field
is only used tpm_tis.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Introduced a private struct tpm_atmel_priv that contains the variables
have_region and region_size that were previously located in struct
tpm_vendor_specific. These fields were only used by tpm_atmel.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Drop field int_queue from tpm_vendor_specific as it is used only by
tpm_tis. Probably all of the fields should be eventually dropped and
moved to the private structures of different drivers but it is better to
do this one step at a time in order not to break anything.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Fixes: 20e0152393b41 ("tpm: fix crash in tpm_tis deinitialization")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reported-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
On my Lenovo x250 the following situation occurs:
[18697.813871] tpm_crb MSFT0101:00: can't request region for resource
[mem 0xacdff080-0xacdfffff]
The mapping of the control area overlaps the mapping of the command
buffer. The control area is mapped over page, which is not right. It
should mapped over sizeof(struct crb_control_area).
Fixing this issue unmasks another issue. Command and response buffers
can overlap and they do interleave on this machine. According to the PTP
specification the overlapping means that they are mapped to the same
buffer.
The commit has been also on a Haswell NUC where things worked before
applying this fix so that the both code paths for response buffer
initialization are tested.
Cc: stable@vger.kernel.org
Fixes: 1bd047be37 ("tpm_crb: Use devm_ioremap_resource")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
We can get rid of tpm_reg variable in get_burstcount.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
When st33zp24_spi_acpi_request_resources() gets called we
already know that the entries in ->acpi_match_table have matched ACPI ID
of the device.
In addition spi_device pointer cannot be NULL in any case (otherwise I2C
core would not call ->probe() for the driver in the first place).
Drop the two useless checks from the driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
When st33zp24_i2c_acpi_request_resources() gets called we
already know that the entries in ->acpi_match_table have matched ACPI ID
of the device.
In addition I2C client pointer cannot be NULL in any case (otherwise I2C
core would not call ->probe() for the driver in the first place).
Drop the two useless checks from the driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The iomem resource is needed only temporarily so it is better to pass
it on instead of storing it permanently. Named the variable as io_res
so that the code better documents itself.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
rmmod crashes the driver because tpm_chip_unregister() already sets ops
to NULL. This commit fixes the issue by moving tpm2_shutdown() to
tpm_chip_unregister(). This commit is also cleanup because it removes
duplicate code from tpm_crb and tpm_tis to the core.
Fixes: 4d3eac5e156a ("tpm: Provide strong locking for device removal")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Created a local variable pointing to the INT_ENABLE_x register. The
expression clearing INT_ENABLE_x.globalIntEnable is unreadable and
hard to modify without surpassing the 80 char boundary.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Christophe Ricard <christophe-h.ricard@st.com>
A cleanup patch changed the prototype of the regular tpm_bios_log_setup
function, but not that of the stub that is used when the TPM is disabled,
causing a harmless build warning:
drivers/char/tpm/tpm-chip.c: In function 'tpm1_chip_register':
drivers/char/tpm/tpm-chip.c:287:38: error: passing argument 1 of 'tpm_bios_log_setup' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
chip->bios_dir = tpm_bios_log_setup(dev_name(&chip->dev));
In file included from ../drivers/char/tpm/tpm-chip.c:30:0:
../drivers/char/tpm/tpm_eventlog.h:83:31: note: expected 'char *' but argument is of type 'const char *'
static inline struct dentry **tpm_bios_log_setup(char *name)
This changes the stub function to match the normal prototype,
avoiding that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: aca8db8088c3 ("tpm: Get rid of devname")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Replace the device number bitmap with IDR. Extend the number of devices we
can create to 64k.
Since an IDR allows us to associate a pointer with an ID, we use this now
to rewrite tpm_chip_find_get() to simply look up the chip pointer by the
given device ID.
Protect the IDR calls with a mutex.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
tpm_chip_alloc becomes a typical subsystem allocate call.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Now that the tpm core has strong locking around 'ops' it is possible
to remove a TPM driver, module and all, even while user space still
has things like /dev/tpmX open. For consistency and simplicity, drop
the module locking entirely.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Add a read/write semaphore around the ops function pointers so
ops can be set to null when the driver un-registers.
Previously the tpm core expected module locking to be enough to
ensure that tpm_unregister could not be called during certain times,
however that hasn't been sufficient for a long time.
Introduce a read/write semaphore around 'ops' so the core can set
it to null when unregistering. This provides a strong fence around
the driver callbacks, guaranteeing to the driver that no callbacks
are running or will run again.
For now the ops_lock is placed very high in the call stack, it could
be pushed down and made more granular in future if necessary.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Now that we have a proper struct device just use dev_name() to
access this value instead of keeping two copies.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This is a hold over from before the struct device conversion.
- All prints should be using &chip->dev, which is the Linux
standard. This changes prints to use tpm0 as the device name,
not the PnP/etc ID.
- The few places involving sysfs/modules that really do need the
parent just use chip->dev.parent instead
- We no longer need to get_device(pdev) in any places since it is no
longer used by any of the code. The kref on the parent is held
by the device core during device_add and dropped in device_del
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Simplify st33zp24_spi_acpi_request_resources, st33zp24_spi_of_request_resources
and st33zp24_spi_request_resources to have the same prototype and using
spi_get_drvdata.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Simplify st33zp24_i2c_acpi_request_resources, st33zp24_i2c_of_request_resources
and st33zp24_i2c_request_resources to have the same prototype and using
i2c_get_clientdata.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Add check in st33zp24_spi_evaluate_latency helping to diagnose if the chip
is present or in a bad state.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
DT headers already define NOOP routines when CONFIG_OF is not defined.
[jarkko.sakkinen@linux.intel.com: I tested that the driver compiles
without warnings and errors with and without CONFIG_OF flag.]
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Remove spi_xfer from st33zp24_spi_phy structure and declare local spi_xfer
when needed instead.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
An affectation is enough when copying 1 byte. Remove memcpy usage where
possible.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Make sure every function name use st33zp24_spi_ prefix.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
nbr_dummy_bytes variable could be easily replaced by phy->latency in
st33zp24_spi_send and st33zp24_spi_recv.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Simplify st33zp24_spi_acpi_request_resources, st33zp24_spi_of_request_resources
and st33zp24_spi_request_resources to have the same prototype and using
spi_get_drvdata.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Simplify st33zp24_i2c_acpi_request_resources, st33zp24_i2c_of_request_resources
and st33zp24_i2c_request_resources to have the same prototype and using
i2c_get_clientdata.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Add check in st33zp24_spi_evaluate_latency helping to diagnose if the chip
is present or in a bad state.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The core st33zp24 module is useless without either the I2C or the
SPI access module. So hide NFC_ST_NCI and select it automatically
if either TCG_TIS_ST33ZP24_I2C or TCG_TIS_ST33ZP24_SPI is selected.
This avoids presenting TCG_TIS_ST33ZP24 when neither TCG_TIS_ST33ZP24_I2C
nor TCG_TIS_ST33ZP24_SPI can be selected.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
DT headers already define NOOP routines when CONFIG_OF is not defined.
[jarkko.sakkinen@linux.intel.com: I tested that the driver compiles
without warnings and errors with and without CONFIG_OF flag.]
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Remove spi_xfer from st33zp24_spi_phy structure and declare local spi_xfer
when needed instead.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
An affectation is enough when copying 1 byte. Remove memcpy usage where
possible.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Make sure every function name use st33zp24_spi_ prefix.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
nbr_dummy_bytes variable could be easily replaced by phy->latency in
st33zp24_spi_send and st33zp24_spi_recv.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
drivers/char/tpm/tpm_tis.c:838: warning: ‘tpm_tis_resume’ defined but
not used
Reported-by: James Morris <jmorris@namei.org>
Fixes: 00194826e6 ("tpm_tis: Clean up the force=1 module parameter")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
cc: stable@vger.kernel.org
In all cases use dev_name() for the mapped resources. This is both
for sake of consistency and also with some platforms resource name
given by ACPI object seems to return garbage.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fixes: 1bd047be37 ("tpm_crb: Use devm_ioremap_resource")
The commit 0cc698af36 ("vTPM: support little endian guests") copied
the event, but without the event data, did an endian conversion on the
size and tried to output the event data from the copied version, which
has only have one byte of the data, resulting in garbage event data.
[jarkko.sakkinen@linux.intel.com: fixed minor coding style issues and
renamed the local variable tempPtr as temp_ptr now that there is an
excuse to do this.]
Signed-off-by: Harald Hoyer <harald@redhat.com>
Fixes: 0cc698af36 ("vTPM: support little endian guests")
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
cc: stable@vger.kernel.org
Call put_device() and return error code if devm_add_action() fails.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Fixes: 8e0ee3c9fa ("tpm: fix the cleanup of struct tpm_chip")
It's better to set the continueSession attribute for the unseal
operation so that the session object is not removed as a side-effect
when the operation is successful. Since a user process created the
session, it should be also decide when the session is destroyed.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fixes: 5beb0c435b ("keys, trusted: seal with a TPM2 authorization policy")
If the initialization fails before tpm_chip_register(), put_device()
will be not called, which causes release callback not to be called.
This patch fixes the issue by adding put_device() to devres list of
the parent device.
Fixes: 313d21eeab ("tpm: device class for tpm")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
cc: stable@vger.kernel.org
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Fixed the rollback and gave more self-documenting names for the
functions.
Fixes: d972b0523f ("tpm: fix call order in tpm-chip.c")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
cc: stable@vger.kernel.org
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
To support the force mode in tpm_tis we need to use resource locking
in tpm_crb as well, via devm_ioremap_resource.
The light restructuring better aligns crb and tis and makes it easier
to see the that new changes make sense.
The control area and its associated buffers do not always fall in the
range of the iomem resource given by the ACPI object. This patch fixes
the issue by mapping the buffers if this is the case.
[jarkko.sakkinen@linux.intel.com: squashed update described in the
last paragraph.]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
ioread32 and readl are defined to read from PCI style memory, ie little
endian and return the result in host order. On platforms where a
swap is required ioread32/readl do the swap internally (eg see ppc).
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
The TPM core has long assumed that every device has a driver attached,
however the force path was attaching the TPM core outside of a driver
context. This isn't generally reliable as the user could detatch the
driver using sysfs or something, but commit b8b2c7d845 ("base/platform:
assert that dev_pm_domain callbacks are called unconditionally")
forced the issue by leaving the driver pointer NULL if there is
no probe.
Rework the TPM setup to create a platform device with resources and
then allow the driver core to naturally bind and probe it through the
normal mechanisms. All this structure is needed anyhow to enable TPM
for OF environments.
Finally, since the entire flow is changing convert the init/exit to use
the modern ifdef-less coding style when possible
Reported-by: "Wilck, Martin" <martin.wilck@ts.fujitsu.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Wilck, Martin <martin.wilck@ts.fujitsu.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
This does a request_resource under the covers which means tis holds a
lock on the memory range it is using so other drivers cannot grab it.
When doing probing it is important to ensure that other drivers are
not using the same range before tis starts touching it.
To do this flow the actual struct resource from the device right
through to devm_ioremap_resource. This ensures all the proper resource
meta-data is carried down.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Wilck, Martin <martin.wilck@ts.fujitsu.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
If the ACPI tables do not declare a memory resource for the TPM2
then do not just fall back to the x86 default base address.
Also be stricter when checking the ancillary TPM2 ACPI data and error
out if any of this data is wrong rather than blindly assuming TPM1.
Fixes: 399235dc6e ("tpm, tpm_tis: fix tpm_tis ACPI detection issue with TPM 2.0")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Wilck, Martin <martin.wilck@ts.fujitsu.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Instead of clearing the global interrupts flag when any device
does not have an interrupt just pass -1 through tpm_info.irq.
The only thing that asks for autoprobing is the force=1 path.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Wilck, Martin <martin.wilck@ts.fujitsu.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
include/acpi/actbl2.h is the proper place for these definitions
and the needed TPM2 ones have been there since
commit 413d4a6def ("ACPICA: Update TPM2 ACPI table")
This also drops a couple of le32_to_cpu's for members of this table,
the existing swapping was not done consistently, and the standard
used by other Linux callers of acpi_get_table is unswapped.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Wilck, Martin <martin.wilck@ts.fujitsu.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
In my original patch sealing with policy was done with dynamically
allocated buffer that I changed later into an array so the checks in
tpm2-cmd.c became invalid. This patch fixes the issue.
Fixes: 5beb0c435b ("keys, trusted: seal with a TPM2 authorization policy")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
tpm_tis.c already gets actbl2.h via linux/acpi.h -> acpi/acpi.h ->
acpi/actbl.h -> acpi/actbl2.h, so the direct include in tpm_tis.c
is not needed.
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
TPM2 supports authorization policies, which are essentially
combinational logic statements repsenting the conditions where the data
can be unsealed based on the TPM state. This patch enables to use
authorization policies to seal trusted keys.
Two following new options have been added for trusted keys:
* 'policydigest=': provide an auth policy digest for sealing.
* 'policyhandle=': provide a policy session handle for unsealing.
If 'hash=' option is supplied after 'policydigest=' option, this
will result an error because the state of the option would become
mixed.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Added 'hash=' option for selecting the hash algorithm for add_key()
syscall and documentation for it.
Added entry for sm3-256 to the following tables in order to support
TPM_ALG_SM3_256:
* hash_algo_name
* hash_digest_size
Includes support for the following hash algorithms:
* sha1
* sha256
* sha384
* sha512
* sm3-256
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
When the TPM response reception is interrupted in the wait_event_interruptable
call, the TPM is still busy processing the command and will only deliver the
response later. So we have to wait for an outstanding response before sending
a new request to avoid trying to put a 2nd request into the CRQ. Also reset
the res_len before sending a command so we will end up in that
wait_event_interruptable() waiting for the response rather than reading the
command packet as a response.
The easiest way to trigger the problem is to run the following
cd /sys/device/vio/71000004
while :; cat pcrs >/dev/null; done
And press Ctrl-C. This will then display an error
tpm_ibmvtpm 71000004: tpm_transmit: tpm_recv: error -4
followed by several other errors once interaction with the TPM resumes.
tpm_ibmvtpm 71000004: A TPM error (101) occurred attempting to determine the number of PCRS.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Ashley Lai <ashley@ashleylai.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
auto-probing doesn't work with shared interrupts, and the auto detection
interrupt range is for x86 only.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Now that the probe and run cases are merged together we can use a
much simpler setup flow where probe and normal setup are done with
exactly the same code.
Since the new flow always calls tpm_gen_interrupt to confirm the IRQ
there is also no longer any need to call tpm_get_timeouts twice.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
The new code that works directly in tpm_tis_send is able to handle
IRQ probing duties as well, so just use it for everything.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off--by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
IRQ probing needs to know that the TPM is working before trying to
probe, so move tpm_get_timeouts() to the top of the tpm_tis_init().
This has the advantage of also getting the correct timeouts loaded
before doing IRQ probing.
All the timeout handling code is moved to tpm_get_timeouts() in order to
remove duplicate code in tpm_tis and tpm_crb.
[jarkko.sakkinen@linux.intel.com: squashed two patches together and
improved the commit message.]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
This should be done very early, before anything could possibly
cause the TPM to generate an interrupt. If the IRQ line is shared
with another driver causing an interrupt before setting up our
handler will be very bad.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
The interrupt is always allocated with devm_request_irq so it
must always be freed with devm_free_irq.
Fixes: 448e9c55c1 ("tpm_tis: verify interrupt during init")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
commit 07b133e606 ("char/tpm: simplify duration calculation and
eliminate smatch warning.") includes a misleading test that is always
false. The tpm_ordinal_duration table is only valid for TPM_PROTECTED
ordinals where the higher 16 bits are all 0, anyway.
Signed-off-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
__compat_only_sysfs_link_entry_to_kobj() was unconditionally called for
TPM1 chips, which caused crash on Acer C720 laptop where DSM for the
ACPI object did not exist.
There are two reasons for unwanted behavior:
* The code did not check whether
__compat_only_sysfs_link_entry_to_kobj() returned -ENOENT. This is
OK. It just meanst that ppi is not available.
* The code did not clean up properly. Compat link should added only
after all other init is done.
This patch sorts out these issues.
Fixes: 9b774d5cf2
Reported-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Acked-by: Peter Huewe <PeterHuewe@gmx.de>
The 'migratable' flag was not added to the key payload. This patch
fixes the problem.
Fixes: 0fe5480303 ("keys, trusted: seal/unseal with TPM 2.0 chips")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <PeterHuewe@gmx.de>
Mimi reported that afb5abc reverts the fix in 398a1e7. This patch
reverts it back.
Fixes: afb5abc262 ("tpm: two-phase chip management functions")
Reported-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <PeterHuewe@gmx.de>
Reference to the 'np' node is dropped before dereferencing the 'sizep' and
'basep' pointers, which could by then point to junk if the node has been
freed.
Refactor code to call 'of_node_put' later.
Fixes: c5df39262d ("drivers/char/tpm: Add securityfs support for event log")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <PeterHuewe@gmx.de>
If the probing finishes without success, it will leave the value 15 in
the TPM_IRQ_VECTOR register. If the driver is unloaded and reloaded, it
will "think" that the hardware had been programmed with IRQ 15, and will
not probe again.
This patch restores the original value in the IO memory if no IRQ is
probed.
Signed-off-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <PeterHuewe@gmx.de>
Release IRQs used for probing only. Otherwise the TPM will end up
with all IRQs 3-15 assigned.
Fixes: afb5abc262 ("tpm: two-phase chip management functions")
Signed-off-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <PeterHuewe@gmx.de>
Pull security subsystem update from James Morris:
"This is mostly maintenance updates across the subsystem, with a
notable update for TPM 2.0, and addition of Jarkko Sakkinen as a
maintainer of that"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (40 commits)
apparmor: clarify CRYPTO dependency
selinux: Use a kmem_cache for allocation struct file_security_struct
selinux: ioctl_has_perm should be static
selinux: use sprintf return value
selinux: use kstrdup() in security_get_bools()
selinux: use kmemdup in security_sid_to_context_core()
selinux: remove pointless cast in selinux_inode_setsecurity()
selinux: introduce security_context_str_to_sid
selinux: do not check open perm on ftruncate call
selinux: change CONFIG_SECURITY_SELINUX_CHECKREQPROT_VALUE default
KEYS: Merge the type-specific data with the payload data
KEYS: Provide a script to extract a module signature
KEYS: Provide a script to extract the sys cert list from a vmlinux file
keys: Be more consistent in selection of union members used
certs: add .gitignore to stop git nagging about x509_certificate_list
KEYS: use kvfree() in add_key
Smack: limited capability for changing process label
TPM: remove unnecessary little endian conversion
vTPM: support little endian guests
char: Drop owner assignment from i2c_driver
...
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The base pointer for the event log is allocated in the local
kernel (in prom_instantiate_sml()), therefore it is already in
the host's endian byte order and requires no conversion.
The content of the 'basep' pointer in read_log() stores the
base address of the log. This patch ensures that it is correctly
implemented.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This patch makes the code endianness independent. We defined a
macro do_endian_conversion to apply endianness to raw integers
in the event entries so that they will be displayed properly.
tpm_binary_bios_measurements_show() is modified for the display.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Replace all occurrences of '/ibm,vtpm' with '/vdevice/vtpm',
as only the latter is guanranteed to be available for the client OS.
The '/ibm,vtpm' node should only be used by Open Firmware, which
is susceptible to changes.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Added tpm_trusted_seal() and tpm_trusted_unseal() API for sealing
trusted keys.
This patch implements basic sealing and unsealing functionality for
TPM 2.0:
* Seal with a parent key using a 20 byte auth value.
* Unseal with a parent key using a 20 byte auth value.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This patch introduces struct tpm_buf that provides a string buffer for
constructing TPM commands. This allows to construct variable sized TPM
commands. For the buffer a page is allocated and mapped, which limits
maximum size to PAGE_SIZE.
Variable sized TPM commands are needed in order to add algorithmic
agility.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Moved PPI attributes to the character device directory. This aligns with
the sysfs guidelines and makes them race free because they are created
atomically with the character device as part of device_register().The
character device and the sysfs attributes appear at the same time to the
user space.
As part of this change we enable PPI attributes also for TPM 2.0
devices. In order to retain backwards compatibility with TPM 1.x
devices, a symlink is created to the platform device directory.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Tested-by: Mimi Zohar <zohar@linux.vnet.ibm.com> (on TPM 1.2)
Tested-by: Chris J Arges <chris.j.arges@canonical.com>
Tested-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Both for FIFO and CRB interface TCG has decided to use the same HID
MSFT0101. They can be differentiated by looking at the start method from
TPM2 ACPI table. This patches makes necessary fixes to tpm_tis and
tpm_crb modules in order to correctly detect, which module should be
used.
For MSFT0101 we must use struct acpi_driver because struct pnp_driver
has a 7 character limitation.
It turned out that the root cause in b371616b8 was not correct for
https://bugzilla.kernel.org/show_bug.cgi?id=98181.
v2:
* One fixup was missing from v1: is_tpm2_fifo -> is_fifo
v3:
* Use pnp_driver for existing HIDs and acpi_driver only for MSFT0101 in
order ensure backwards compatibility.
v4:
* Check for FIFO before doing *anything* in crb_acpi_add().
* There was return immediately after acpi_bus_unregister_driver() in
cleanup_tis(). This caused pnp_unregister_driver() not to be called.
Cc: stable@kernel.org
Reported-by: Michael Saunders <mick.saunders@gmail.com>
Reported-by: Michael Marley <michael@michaelmarley.com>
Reported-by: Jethro Beekman <kernel@jbeekman.nl>
Reported-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Michael Marley <michael@michaelmarley.com>
Tested-by: Mimi Zohar <zohar@linux.vnet.ibm.com> (on TPM 1.2)
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
The command buffer address must be read with exactly two 32-bit reads.
Otherwise, on some HW platforms, it seems that HW will abort the read
operation, which causes CPU to fill the read bytes with 1's. Therefore,
we cannot rely on memcpy_fromio() but must call ioread32() two times
instead.
Also, this matches the PC Client Platform TPM Profile specification,
which defines command buffer address with two 32-bit fields.
Cc: stable@kernel.org
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
At ibm vtpm initialzation, tpm_ibmvtpm_probe() registers its interrupt
handler, ibmvtpm_interrupt, which calls ibmvtpm_crq_process to allocate
memory for rtce buffer. The current code uses 'GFP_KERNEL' as the
type of kernel memory allocation, which resulted a warning at
kernel/lockdep.c. This patch uses 'GFP_ATOMIC' instead so that the
allocation is high-priority and does not sleep.
Cc: stable@kernel.org
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
At least some versions of AMI BIOS have corrupted contents in the TPM2
ACPI table and namely the physical address of the control area is set to
zero.
This patch changes the driver to fail gracefully when we observe a zero
address instead of continuing to ioremap.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
When a cdev is contained in a dynamic structure the cdev parent kobj
should be set to the kobj that controls the lifetime of the enclosing
structure. In TPM's case this is the embedded struct device.
Also, cdev_init 0's the whole structure, so all sets must be after,
not before. This fixes module ref counting and cdev.
Cc: <stable@vger.kernel.org>
Fixes: 313d21eeab ("tpm: device class for tpm")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
le64_to_cpu() was applied twice to the physical addresses read from the
control area. This hasn't shown any visible regressions because CRB
driver has been tested only on the little endian platofrms so far.
Reported-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: <stable@vger.kernel.org>
Fixes: 30fc8d138e ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
tpm_ibmvtpm_probe() calls ibmvtpm_reset_crq(ibmvtpm) without having yet
set the virtual device in the ibmvtpm structure. So in ibmvtpm_reset_crq,
the phype call contains empty unit addresses, ibmvtpm->vdev->unit_address.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Cc: <stable@vger.kernel.org>
Fixes: 132f762947 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
- Use a single source list of hypercalls, generating other tables
etc. at build time.
- Add a "Xen PV" APIC driver to support >255 VCPUs in PV guests.
- Significant performance improve to guest save/restore/migration.
- scsiback/front save/restore support.
- Infrastructure for multi-page xenbus rings.
- Misc fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJVL6OZAAoJEFxbo/MsZsTRs3YH/2AycBHs129DNnc2OLmOklBz
AdD43k+FOfZlv0YU80WmPVmOpGGHGB5Pqkix2KtnvPYmtx3pb/5ikhDwSTWZpqBl
Qq6/RgsRjYZ8VMKqrMTkJMrJWHQYbg8lgsP5810nsFBn/Qdbxms+WBqpMkFVo3b2
rvUZj8QijMJPS3qr55DklVaOlXV4+sTAytTdCiubVnaB/agM2jjRflp/lnJrhtTg
yc4NTrIlD1RsMV/lNh92upBP/pCm6Bs0zQ2H1v3hkdhBBmaO0IVXpSheYhfDOHfo
9v209n137N7X86CGWImFk6m2b+EfiFnLFir07zKSA+iZwkYKn75znSdPfj0KCc0=
=bxTm
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-4.1-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen features and fixes from David Vrabel:
- use a single source list of hypercalls, generating other tables etc.
at build time.
- add a "Xen PV" APIC driver to support >255 VCPUs in PV guests.
- significant performance improve to guest save/restore/migration.
- scsiback/front save/restore support.
- infrastructure for multi-page xenbus rings.
- misc fixes.
* tag 'stable/for-linus-4.1-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pci: Try harder to get PXM information for Xen
xenbus_client: Extend interface to support multi-page ring
xen-pciback: also support disabling of bus-mastering and memory-write-invalidate
xen: support suspend/resume in pvscsi frontend
xen: scsiback: add LUN of restored domain
xen-scsiback: define a pr_fmt macro with xen-pvscsi
xen/mce: fix up xen_late_init_mcelog() error handling
xen/privcmd: improve performance of MMAPBATCH_V2
xen: unify foreign GFN map/unmap for auto-xlated physmap guests
x86/xen/apic: WARN with details.
x86/xen: Provide a "Xen PV" APIC driver to support >255 VCPUs
xen/pciback: Don't print scary messages when unsupported by hypervisor.
xen: use generated hypercall symbols in arch/x86/xen/xen-head.S
xen: use generated hypervisor symbols in arch/x86/xen/trace.c
xen: synchronize include/xen/interface/xen.h with xen
xen: build infrastructure for generating hypercall depending symbols
xen: balloon: Use static attribute groups for sysfs entries
xen: pcpu: Use static attribute groups for sysfs entry
Pull security subsystem updates from James Morris:
"Highlights for this window:
- improved AVC hashing for SELinux by John Brooks and Stephen Smalley
- addition of an unconfined label to Smack
- Smack documentation update
- TPM driver updates"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (28 commits)
lsm: copy comm before calling audit_log to avoid race in string printing
tomoyo: Do not generate empty policy files
tomoyo: Use if_changed when generating builtin-policy.h
tomoyo: Use bin2c to generate builtin-policy.h
selinux: increase avtab max buckets
selinux: Use a better hash function for avtab
selinux: convert avtab hash table to flex_array
selinux: reconcile security_netlbl_secattr_to_sid() and mls_import_netlbl_cat()
selinux: remove unnecessary pointer reassignment
Smack: Updates for Smack documentation
tpm/st33zp24/spi: Add missing device table for spi phy.
tpm/st33zp24: Add proper wait for ordinal duration in case of irq mode
smack: Fix gcc warning from unused smack_syslog_lock mutex in smackfs.c
Smack: Allow an unconfined label in bringup mode
Smack: getting the Smack security context of keys
Smack: Assign smack_known_web as default smk_in label for kernel thread's socket
tpm/tpm_infineon: Use struct dev_pm_ops for power management
MAINTAINERS: Add Jason as designated reviewer for TPM
tpm: Update KConfig text to include TPM2.0 FIFO chips
tpm/st33zp24/dts/st33zp24-spi: Add dts documentation for st33zp24 spi phy
...
Originally Xen PV drivers only use single-page ring to pass along
information. This might limit the throughput between frontend and
backend.
The patch extends Xenbus driver to support multi-page ring, which in
general should improve throughput if ring is the bottleneck. Changes to
various frontend / backend to adapt to the new interface are also
included.
Affected Xen drivers:
* blkfront/back
* netfront/back
* pcifront/back
* scsifront/back
* vtpmfront
The interface is documented, as before, in xenbus_client.c.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Cc: Konrad Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
MODULE_DEVICE_TABLE is missing in spi phy in case CONFIG_OF is not set.
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
In case the driver is configured to use irq, we are not waiting the answer
for a duration period to see the DATA_AVAIL status bit to raise but at
maximum timeout_c. This may result in critical failure as we will
not wait long enough for the command completion.
Reviewed-by: Jason Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Fixes: bf38b87108 ("tpm/tpm_i2c_stm_st33: Split tpm_i2c_tpm_st33 in 2
layers (core + phy)")
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Make the tpm_infineon driver define its PM callbacks through
a struct dev_pm_ops object rather than by using legacy PM hooks
in struct pnp_driver.
This allows the driver to use tpm_pm_suspend() as its suspend
callback directly, so we can remove the duplicated savestate code.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
I got a lot of requests lately about whether the new TPM2.0 support
includes the FIFO interface for TPM2.0 as well.
The FIFO interface is handled by tpm_tis since FIFO=TIS (more or less).
-> Update the helptext and headline
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
st33zp24 TIS 1.2 support also SPI. It is using a proprietary protocol to
transport TIS data.
Acked-by: Jarkko Sakkinen <jarkko.sakknen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
tpm_i2c_stm_st33 is a TIS 1.2 TPM with a core interface which can be used
by different phy such as i2c or spi. The core part is called st33zp24 which
is also the main part reference.
include/linux/platform_data/tpm_stm_st33.h is renamed consequently.
The driver is also split into an i2c phy in charge of sending/receiving
data as well as managing platform data or dts configuration.
Acked-by: Jarkko Sakkinen <jarkko.sakknen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
io_lpcpd is accessible from struct tpm_stm_dev.
struct st33zp24_platform_data is only valid when using static platform
configuration data, not when using dts.
Reviewed-by: Jason Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
I started to work with PPI interface so that it would be available
under character device sysfs directory and realized that chip
registeration was still too messy.
In TPM 1.x in some rare scenarios (errors that almost never occur)
wrong order in deinitialization steps was taken in teardown. I
reproduced these scenarios by manually inserting error codes in the
place of the corresponding function calls.
The key problem is that the teardown is messy with two separate code
paths (this was inherited when moving code from tpm-interface.c).
Moved TPM 1.x specific register/unregister functionality to own helper
functions and added single code path for teardown in tpm_chip_register().
Now the code paths have been fixed and it should be easier to review
later on this part of the code.
Cc: <stable@vger.kernel.org>
Fixes: 7a1d7e6dd7 ("tpm: TPM 2.0 baseline support")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Removing some boilerplate by using module_pnp_driver instead of calling
register and unregister in the otherwise empty init/exit functions
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- tpm_dev_add_device(): cdev_add() must be done before uevent is
propagated in order to avoid races.
- tpm_chip_register(): tpm_dev_add_device() must be done as the
last step before exposing device to the user space in order to
avoid races.
In addition clarified description in tpm_chip_register().
Fixes: 313d21eeab ("tpm: device class for tpm")
Fixes: afb5abc262 ("tpm: two-phase chip management functions")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Problem: When IMA and VTPM are both enabled in kernel config,
kernel hangs during bootup on LE OS.
Why?: IMA calls tpm_pcr_read() which results in tpm_ibmvtpm_send
and tpm_ibmtpm_recv getting called. A trace showed that
tpm_ibmtpm_recv was hanging.
Resolution: tpm_ibmtpm_recv was hanging because tpm_ibmvtpm_send
was sending CRQ message that probably did not make much sense
to phype because of Endianness. The fix below sends correctly
converted CRQ for LE. This was not caught before because it
seems IMA is not enabled by default in kernel config and
IMA exercises this particular code path in vtpm.
Tested with IMA and VTPM enabled in kernel config and VTPM
enabled on both a BE OS and a LE OS ppc64 lpar. This exercised
CRQ and TPM command code paths in vtpm.
Patch is against Peter's tpmdd tree on github which included
Vicky's previous vtpm le patches.
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # eb71f8a5e3: "Added Little Endian support to vtpm module"
Cc: <stable@vger.kernel.org>
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
- tpm_dev_add_device(): cdev_add() must be done before uevent is
propagated in order to avoid races.
- tpm_chip_register(): tpm_dev_add_device() must be done as the
last step before exposing device to the user space in order to
avoid races.
In addition clarified description in tpm_chip_register().
Fixes: 313d21eeab ("tpm: device class for tpm")
Fixes: afb5abc262 ("tpm: two-phase chip management functions")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Problem: When IMA and VTPM are both enabled in kernel config,
kernel hangs during bootup on LE OS.
Why?: IMA calls tpm_pcr_read() which results in tpm_ibmvtpm_send
and tpm_ibmtpm_recv getting called. A trace showed that
tpm_ibmtpm_recv was hanging.
Resolution: tpm_ibmtpm_recv was hanging because tpm_ibmvtpm_send
was sending CRQ message that probably did not make much sense
to phype because of Endianness. The fix below sends correctly
converted CRQ for LE. This was not caught before because it
seems IMA is not enabled by default in kernel config and
IMA exercises this particular code path in vtpm.
Tested with IMA and VTPM enabled in kernel config and VTPM
enabled on both a BE OS and a LE OS ppc64 lpar. This exercised
CRQ and TPM command code paths in vtpm.
Patch is against Peter's tpmdd tree on github which included
Vicky's previous vtpm le patches.
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # eb71f8a5e3: "Added Little Endian support to vtpm module"
Cc: <stable@vger.kernel.org>
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
The tpm_ibmvtpm module is affected by an unaligned access problem.
ibmvtpm_crq_get_version failed with rc=-4 during boot when vTPM is
enabled in Power partition, which supports both little endian and
big endian modes.
We added little endian support to fix this problem:
1) added cpu_to_be64 calls to ensure BE data is sent from an LE OS.
2) added be16_to_cpu and be32_to_cpu calls to make sure data received
is in LE format on a LE OS.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>
[phuewe: manually applied the patch :( ]
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
If during transmission system error was returned, the logic was to
incorrectly deduce that chip is a TPM 1.x chip. This patch fixes this
issue. Also, this patch changes probing so that message tag is used as the
measure for TPM 2.x, which should be much more stable. A separate function
called tpm2_probe() is encapsulated because it can be used with any
chipset.
Fixes: aec04cbdf7 ("tpm: TPM 2.0 FIFO Interface")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Fixed suspend/resume paths for TPM 2.0 and consolidated all the
associated code to the tpm_pm_suspend() and tpm_pm_resume()
functions. Resume path should be handled by the firmware, i.e.
Startup(CLEAR) for hibernate and Startup(STATE) for suspend.
There might be some non-PC embedded devices in the future where
Startup() is not the handled by the FW but fixing the code for
those IMHO should be postponed until there is hardware available
to test the fixes although extra Startup in the driver code is
essentially a NOP.
Added Shutdown(CLEAR) to the remove paths of TIS and CRB drivers.
Changed tpm2_shutdown() to a void function because there isn't
much you can do except print an error message if this fails with
a system error.
Fixes: aec04cbdf7 ("tpm: TPM 2.0 FIFO Interface")
Fixes: 30fc8d138e ("tpm: TPM 2.0 CRB Interface")
[phuewe: both did send TPM_Shutdown on resume which 'disables' the TPM
and did not send TPM2_Shutdown on teardown which leads some TPM2.0 to
believe there was an attack (no TPM2_Shutdown = no orderly shutdown =
attack)]
Reported-by: Peter Hüwe <PeterHuewe@gmx.de>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This fixes a build failure if CONFIG_PNP is set but CONFIG_ACPI is not:
drivers/char/tpm/tpm_tis.c: In function ?tpm_tis_pnp_init?:
drivers/char/tpm/tpm_tis.c:912:45: error: invalid type argument of
?->? (have ?int?)
acpi_dev_handle = pnp_acpi_device(pnp_dev)->handle;
If CONFIG_PNPACPI is not set pnp_acpi_device is defined as 0 and thus
accesing the handle is not possible.
Fixes: 0dc5536521 ("tpm: fix raciness of PPI interface lookup")
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: James Morris <james.l.morris@oracle.com>
