IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Use generic regamp ramp-delay helper function instead of implementing own.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ROHM BD71815 supports setting voltage levels/regulator status
for HW-states "RUN", "SUSPEND", "LPSR" and "SNVS". Add DT parsing
helper also for SNVS state.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The helper for obtaining HW-state based DVS voltage levels currently only
works for regulators using linear-ranges. Extend support to regulators with
simple linear mappings and add also proper error path if pickable-ranges
regulators call this.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Patch series introducing support for ROHM BD71815 PMIC
ROHM BD71815 is a power management IC used in some battery powered
systems. It contains regulators, GPO(s), charger + coulomb counter, RTC
and a clock gate.
All regulators can be controlled via I2C. LDO4 can additionally be set to
be enabled/disabled by a GPIO. LDO3 voltage could be selected from two
voltages written into separate VSEL reisters using GPIO but this mode is
not supported by driver. On top of that the PMIC has the typical HW
state machine which is present also on many other ROHM PMICs.
IC contains two GPOs - but one of the GPOs is marked as GND in
data-sheet. Thus the driver by default only exposes one GPO. The second
GPO can be enabled by special DT property.
RTC is almost similar to what is on BD71828. For currently used features
only the register address offset to RTC block differs.
The charger driver is not included in this series. ROHM has a charger
driver with some fuel-gauging logig written in but this is not included
here. I am working on separating the logic from HW specific driver and
supporting both BD71815 and BD71828 chargers in separate patch series.
Changelog v5:
Regulator:
- Added regmap helper for regulator ramp-delay and taken it in use
(patches 13, 14, 16 - they can be just dropped if ramp-delay helper is not
a good idea. Patch 15 implements old-fashioned ramp-delay)
GPIO:
- styling changes to GPIO (Mostly suggested by Andy)
- implemented init_valid_mask (but can't count on it yet)
Changelog v4:
- Sorted ROHM chip ID enum
- Statcized DVS structures in regulator driver
- Minor styling for regulator driver
- rebased on v5.12-rc4
Changelog v3:
- GPIO clean-up as suggested by Bartosz
- MFD clean-up as suggested by Lee
- clk-mode dt-binding handling in MFD driver corrected to reflect new
property values.
- Dropped already applied patches
- Rebased on v5.12-rc2
Changelog v2:
- Rebased on top of v5.11-rc3
- Added another "preliminary patch" which fixes HW-dvs voltage
handling (patch 1)
- split regulator patch to two.
- changed dt-binding patch ordering.
regulators:
- staticized probe
- removed some unnecessary defines
- updated comments
- split rohm-regulator patch adding SNVS and supporting simple
linear mapping into two - one adding support for mapping, other
adding SNVS.
GPIO:
- removed unnecessary headers
- clarified dev/parent->dev usage
- removed forgotten #define DEBUG
dt-bindings:
- changed patch order to meet ref-dependencies
- added missing regulator nodes
- changed string property for clk mode to tristated
MFD:
- header cleanups.
CLK:
- fixed commit message
--
Matti Vaittinen (19):
rtc: bd70528: Do not require parent data
mfd: bd718x7: simplify by cleaning unnecessary device data
dt_bindings: bd71828: Add clock output mode
dt_bindings: regulator: Add ROHM BD71815 PMIC regulators
dt_bindings: mfd: Add ROHM BD71815 PMIC
mfd: Add ROHM BD71815 ID
mfd: Sort ROHM chip ID list for better readability
mfd: Support for ROHM BD71815 PMIC core
gpio: support ROHM BD71815 GPOs
regulator: helpers: Export helper voltage listing
regulator: rohm-regulator: linear voltage support
regulator: rohm-regulator: Support SNVS HW state.
regulator: Add regmap helper for ramp-delay setting
regulator: bd718x7, bd71828: Use ramp-delay helper
regulator: Support ROHM BD71815 regulators
regulator: bd71815: use ramp-delay helper
clk: bd718x7: Add support for clk gate on ROHM BD71815 PMIC
rtc: bd70528: Support RTC on ROHM BD71815
MAINTAINERS: Add ROHM BD71815AGW
.../bindings/mfd/rohm,bd71815-pmic.yaml | 201 ++++++
.../bindings/mfd/rohm,bd71828-pmic.yaml | 6 +
.../regulator/rohm,bd71815-regulator.yaml | 116 ++++
MAINTAINERS | 3 +
drivers/clk/clk-bd718x7.c | 9 +-
drivers/gpio/Kconfig | 10 +
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-bd71815.c | 193 ++++++
drivers/mfd/Kconfig | 15 +-
drivers/mfd/rohm-bd71828.c | 486 +++++++++----
drivers/mfd/rohm-bd718x7.c | 43 +-
drivers/regulator/Kconfig | 11 +
drivers/regulator/Makefile | 1 +
drivers/regulator/bd71815-regulator.c | 651 ++++++++++++++++++
drivers/regulator/bd71828-regulator.c | 51 +-
drivers/regulator/bd718x7-regulator.c | 60 +-
drivers/regulator/helpers.c | 101 ++-
drivers/regulator/rohm-regulator.c | 23 +-
drivers/rtc/Kconfig | 6 +-
drivers/rtc/rtc-bd70528.c | 104 +--
include/linux/mfd/rohm-bd71815.h | 562 +++++++++++++++
include/linux/mfd/rohm-bd71828.h | 3 +
include/linux/mfd/rohm-bd718x7.h | 13 -
include/linux/mfd/rohm-generic.h | 15 +-
include/linux/regulator/driver.h | 7 +
25 files changed, 2393 insertions(+), 298 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml
create mode 100644 Documentation/devicetree/bindings/regulator/rohm,bd71815-regulator.yaml
create mode 100644 drivers/gpio/gpio-bd71815.c
create mode 100644 drivers/regulator/bd71815-regulator.c
create mode 100644 include/linux/mfd/rohm-bd71815.h
base-commit: 0d02ec6b3136c73c09e7859f0d0e4e2c4c07b49b
--
2.25.4
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
Some drivers need to translate voltage values to selectors prior regulator
registration. Currently a regulator_desc based list_voltages helper is only
exported for regulators using the linear_ranges. Export similar helper also
for regulators using simple linear mapping.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/1200ef7a50c84327ada019b85f6527b4fc9b5ce1.1617020713.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for PM7325/PMR735A regulators. This ensures
that consumers are able to modify the physical state of PMIC
regulators.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1617192339-3760-3-git-send-email-skakit@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Port the scmi regulator driver to the new SCMI voltage interface based
on protocol handles and common devm_get_ops().
Link: https://lore.kernel.org/r/20210316124903.35011-30-cristian.marussi@arm.com
Cc: Mark Brown <broonie@kernel.org>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
fixes coccicheck warning:
drivers/regulator/mt6360-regulator.c:384:3-10: line 384 is
redundant because platform_get_irq() already prints an error
in fact it is not platform_get_irq but platform_get_irq_byname print error
Signed-off-by: Jian Dong <dongjian@yulong.com>
Link: https://lore.kernel.org/r/1616555474-158789-1-git-send-email-dj0227@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Few drivers implement remove call-back only for ensuring a delayed
work gets cancelled prior driver removal. Clean-up these by switching
to use devm_delayed_work_autocancel() instead.
Additionally, this helps avoiding mixing devm and manual resource
management and cleans up a (theoretical?) bug where devm managed
over-current IRQ might schedule a new work item after wq was cleaned
at remove().
This change is compile-tested only. All testing is appreciated.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/3bd35bb43257f4bf5b99f75d207ed5e1e08d1d38.1616506559.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe() function returns an uninitialized variable in the success
path. There is no need for the "err" variable at all, just delete it.
Fixes: b014e9fae7e7 ("regulator: Support ROHM BD9576MUF and BD9573MUF")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/YEsbfLJfEWtnRpoU@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the "backup_mode" device attribute from sprintf() to
sysfs_emit(), as the latter is aware of the PAGE_SIZE buffer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210312130242.3390038-4-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
If a regulator fails to register, the driver prints an error message
like:
bd9571mwv-regulator bd9571mwv-regulator.6.auto: failed to register bd9571mwv-regulator regulator
However, the platform device's name is already printed as part of
dev_err(), and does not allow the user to distinguish among the various
regulators that are part of the PMIC.
Fix this by printing regulator_desc.name instead, to change the message
like:
bd9571mwv-regulator bd9571mwv-regulator.6.auto: failed to register DVFS regulator
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20210312130242.3390038-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
According to Table 30 ("DVFS_MoniVDAC [6:0] Setting Table") in the
BD9571MWV-M Datasheet Rev. 002, the valid voltage range is 600..1100 mV
(settings 0x3c..0x6e). While the lower limit is taken into account (by
setting regulator_desc.linear_min_sel to 0x3c), the upper limit is not.
Fix this by reducing regulator_desc.n_voltages from 0x80 to 0x6f.
Fixes: e85c5a153fe237f2 ("regulator: Add ROHM BD9571MWV-M PMIC regulator driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210312130242.3390038-2-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
In one of the error paths of the for_each_child_of_node() loop,
add missing call to of_node_put().
Fix the following coccicheck warning:
./drivers/regulator/scmi-regulator.c:343:1-23: WARNING: Function
"for_each_child_of_node" should have of_node_put() before return around
line 347.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1614303575-27436-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The voltages in pf8x00_sw7_voltages are in ascendant order, so use
regulator_map_voltage_ascend.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210216060128.126938-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ULT LV_P50 shares the same configuration as the other ULT LV_Pxxx
and the ULT P300 shares the same as the other ULT Pxxx.
These two regulator types are found on PM8950 and its variants.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210225213514.117031-1-konrad.dybcio@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of error, the function dev_get_regmap() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Fixes: 9351ab8b0cb6 ("regulator: rt4831: Adds support for Richtek RT4831 DSV regulator")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210305034930.3236099-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver uses the DVS registers PCA9450_REG_BUCKxOUT_DVS0 to set the
voltage for the buck regulators 1, 2 and 3. This has no effect as the
PRESET_EN bit is set by default and therefore the preset values are used
instead, which are set to 850 mV.
To fix this we clear the PRESET_EN bit at time of initialization.
Fixes: 0935ff5f1f0a ("regulator: pca9450: add pca9450 pmic driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210222115229.166620-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes the return value of pca9450_i2c_probe() to use the correct
error code when getting the sd-vsel GPIO fails.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210222150809.208942-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
- Standardise MFD_CELL_* helpers
- New Drivers
- Add support for Acer Iconia Tab A500 Embedded Controller
- New Device Support
- Add support for ROHM BD9574MWF to BD9571MWV
- Add support for Intel Alder Lake PCH-P PCI to LPSS
- Add support for Intel Alder Lake PCH-S PCI to LPSS
- New Functionality
- Support ACPI enumeration; arizona
- Fix-ups
- Managed resources; bd9571mwv
- DT additions/fix-ups; bd9571mwv, iqs62x, max8997, gateworks-gsc, ene-kb930
- Convert to SPDX; bd9571mw
- Fix return values/error handling; sunxi
- Provide SOFTDEP; arizona
- Make use of DIV_ROUND_UP; mcp-sa11x0
- Use generic APIs; arizona
- Add MAC address sysfs entries; intel-m10-bmc
- Trivial: Coding-style fix-ups; iqs62x
- Trivial: Remove superflouous code; iqs62x
- Clear-up naming conventions; iqs62x
- Bug Fixes
- Fix 'pointer from integer' error; altera-sysmgr
- Convert SGI_MFD_IOC3 from tristate to bool; Kconfig
- Fix interrupt handling; gateworks-gsc
- Extend required delay; iqs62x
- Do not use I2C polling during calibration; iqs62x
- Do no adjust clock frequency during calibration; iqs62x
- Fix use-after-free; wm831x-auxad
-----BEGIN PGP SIGNATURE-----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=ieAS
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Standardise MFD_CELL_* helpers
New Drivers:
- Add support for Acer Iconia Tab A500 Embedded Controller
New Device Support:
- Add support for ROHM BD9574MWF to BD9571MWV
- Add support for Intel Alder Lake PCH-P PCI to LPSS
- Add support for Intel Alder Lake PCH-S PCI to LPSS
New Functionality:
- Support ACPI enumeration; arizona
Fix-ups:
- Managed resources; bd9571mwv
- DT additions/fix-ups; bd9571mwv, iqs62x, max8997, gateworks-gsc, ene-kb930
- Convert to SPDX; bd9571mw
- Fix return values/error handling; sunxi
- Provide SOFTDEP; arizona
- Make use of DIV_ROUND_UP; mcp-sa11x0
- Use generic APIs; arizona
- Add MAC address sysfs entries; intel-m10-bmc
- Trivial: Coding-style fix-ups; iqs62x
- Trivial: Remove superflouous code; iqs62x
- Clear-up naming conventions; iqs62x
Bug Fixes:
- Fix 'pointer from integer' error; altera-sysmgr
- Convert SGI_MFD_IOC3 from tristate to bool; Kconfig
- Fix interrupt handling; gateworks-gsc
- Extend required delay; iqs62x
- Do not use I2C polling during calibration; iqs62x
- Do no adjust clock frequency during calibration; iqs62x
- Fix use-after-free; wm831x-auxad"
* tag 'mfd-next-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (32 commits)
mfd: wm831x-auxadc: Prevent use after free in wm831x_auxadc_read_irq()
mfd: iqs62x: Do not change clock frequency during ATI
mfd: iqs62x: Do not poll during ATI
mfd: iqs62x: Increase interrupt handler return delay
mfd: iqs62x: Rename regmap_config struct
mfd: iqs62x: Remove unused bit mask
mfd: iqs62x: Remove superfluous whitespace above fallthroughs
mfd: intel-lpss: Add Intel Alder Lake PCH-S PCI IDs
mfd: intel-m10-bmc: Expose MAC address and count
mfd: Add driver for Embedded Controller found on Acer Iconia Tab A500
dt-bindings: mfd: Add ENE KB930 Embedded Controller binding
dt-bindings: mfd: gateworks-gsc: Add fan-tach mode
mfd: intel-lpss: Add Intel Alder Lake PCH-P PCI IDs
mfd: gateworks-gsc: Fix interrupt type
mfd: Standardise MFD_CELL_* helper names
mfd: mcp-sa11x0: Use DIV_ROUND_UP to calculate rw_timeout
mfd: max8997: Add of_compatible to Extcon and Charger mfd_cell
dt-bindings: mfd: Correct the node name of the panel LED
mfd: sgi-ioc3: Turn Kconfig option into a bool
mfd: altera-sysmgr: Fix physical address storing more
...
The ROHM BD718x7 and BD71828 drivers support setting HW state
specific voltages from device-tree. This is used also by various
in-tree DTS files.
These drivers do incorrectly try to compose bit-map using enum
values. By a chance this works for first two valid levels having
values 1 and 2 - but setting values for the rest of the levels
do indicate capability of setting values for first levels as
well. Luckily the regulators which support setting values for
SUSPEND/LPSR do usually also support setting values for RUN
and IDLE too - thus this has not been such a fatal issue.
Fix this by defining the old enum values as bits and fixing the
parsing code. This allows keeping existing IC specific drivers
intact and only slightly changing the rohm-regulator.c
Fixes: 21b72156ede8b ("regulator: bd718x7: Split driver to common and bd718x7 specific parts")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210212080023.GA880728@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
By default the PCA9450 doesn't handle the assertion of the WDOG_B
signal, but this is required to guarantee that things like software
resets triggered by the watchdog work reliably.
As we don't want to rely on the bootloader to enable this, we tell
the PMIC to issue a cold reset in case the WDOG_B signal is
asserted (WDOG_B_CFG = 10), just as the NXP U-Boot code does.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210211105534.38972-3-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
LDO5 has two separate control registers. LDO5CTRL_L is used if the
input signal SD_VSEL is low and LDO5CTRL_H if it is high.
The current driver implementation only uses LDO5CTRL_H. To make this
work on boards that have SD_VSEL connected to a GPIO, we add support
for specifying an optional GPIO and setting it to high at probe time.
In the future we might also want to add support for boards that have
SD_VSEL set to a fixed low level. In this case we need to change the
driver to be able to use the LDO5CTRL_L register.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210211105534.38972-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the correct name to avoid ldo7 commands being sent to ldo6's address.
Fixes: 06369bcc15a1 ("regulator: qcom-rpmh: Add support for SM8150")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210211034935.5622-1-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
Calling the disable_irq() from irq handler might be a bad idea as
disable_irq() should wait for handlers to run. I don't see why
this wouldn't deadlock in wait_event waiting for the threaded
handler to complete.
Use disable_irq_nosync() instead.
Fixes: 390af53e04114 ("regulator: qcom-labibb: Implement short-circuit and over-current IRQs")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/f2c4c88d90bf7473e1b84b8a99b7b33d7a081764.1612249657.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes regulator_get() gets called twice for the same supply on the
same device. This may happen e.g. when a framework / library is used
which uses the regulator; and the driver itself also needs to enable
the regulator in some cases where the framework will not enable it.
Commit ff268b56ce8c ("regulator: core: Don't spew backtraces on
duplicate sysfs") already takes care of the backtrace which would
trigger when creating a duplicate consumer symlink under
/sys/class/regulator/regulator.%d in this scenario.
Commit c33d442328f5 ("debugfs: make error message a bit more verbose")
causes a new error to get logged in this scenario:
[ 26.938425] debugfs: Directory 'wm5102-codec-MICVDD' with parent 'spi-WM510204:00-MICVDD' already present!
There is no _nowarn variant of debugfs_create_dir(), but we can detect
and avoid this problem by checking the return value of the earlier
sysfs_create_link_nowarn() call.
Add a check for the earlier sysfs_create_link_nowarn() failing with
-EEXIST and skip the debugfs_create_dir() call in that case, avoiding
this error getting logged.
Fixes: c33d442328f5 ("debugfs: make error message a bit more verbose")
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210122183250.370571-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds suspend/resume support so that it is possible to
configure the LDOs and BUCKs as on or off during suspend phase as
well as to configure suspend specific voltages.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Link: https://lore.kernel.org/r/4c2e79d4fa96befdc9a6c59c3ff27b0a34f9fb56.camel@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make regulator_sync_voltage() to re-balance voltage state of a coupled
regulators instead of changing the voltage directly.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Dmitry Osipenko <digetx@gmail.com> # A500 T20 and Nexus7 T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210122174311.28230-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With commit eaa7995c529b54 (regulator: core: avoid
regulator_resolve_supply() race condition) we started holding the rdev
lock while resolving supplies, an operation that requires holding the
regulator_list_mutex. This results in lockdep warnings since in other
places we take the list mutex then the mutex on an individual rdev.
Since the goal is to make sure that we don't call set_supply() twice
rather than a concern about the cost of resolution pull the rdev lock
and check for duplicate resolution down to immediately before we do the
set_supply() and drop it again once the allocation is done.
Fixes: eaa7995c529b54 (regulator: core: avoid regulator_resolve_supply() race condition)
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210122132042.10306-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The device node reference obtained with of_get_child_by_name() should be
dropped on error paths.
Fixes: 26aec009f6b6 ("regulator: add device tree support for s5m8767")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210121155914.48034-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulators from PMC8180 and PMC8180C exposed by the RPMH in the
Qualcomm SC8180X seems to be the same as PM8150 and PM8150L. Add
compatibles for the two new PMICs and reuse the definition of the
existing PMICs.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210120224901.1611232-2-bjorn.andersson@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Call of_node_put() to drop references of regulators_np and reg_np before
returning error code.
Fixes: 9ae5cc75ceaa ("regulator: s5m8767: Pass descriptor instead of GPIO number")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210121032756.49501-1-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ST-Ericsson U300 platform is getting removed, so this driver is no
longer needed.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210120151307.1726876-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Okay, the title may be a little "aggressive"? However, the qcom-labibb
driver wasn't really .. doing much.
The current form of this driver is only taking care of enabling or
disabling the regulators, which is pretty useless if they were not
pre-set from the bootloader, which sets them only if continuous
splash is enabled.
Moreover, some bootloaders are setting a higher voltage and/or a higher
current limit compared to what's actually required by the attached
hardware (which is, in 99.9% of the cases, a display) and this produces
a higher power consumption, higher heat output and a risk of actually
burning the display if kept up for a very long time: for example, this
is true on at least some Sony Xperia MSM8998 (Yoshino platform) and
especially on some Sony Xperia SDM845 (Tama platform) smartphones.
In any case, the main reason why this change was necessary for us is
that, during the bringup of Sony Xperia MSM8998 phones, we had an issue
with the bootloader not turning on the display and not setting the lab
and ibb regulators before booting the kernel, making it impossible to
powerup the display.
With this said, this patchset enables setting voltage, current limiting,
overcurrent and short-circuit protection.. and others, on the LAB/IBB
regulators.
Each commit in this patch series provides as many informations as
possible about what's going on and testing methodology.
Changes in v4:
- Remove already applied commit
- Add commit to switch to regulator_{list,map}_voltage_linear
which in v3 got squashed in the commit that got removed in v4.
Changes in v3:
- Improved check for PBS disable and short-circuit condition:
during the testing of short-circuit, coincidentally another
register reading zero on the interesting bit was probed,
which didn't trigger a malfunction of the SC logic, but was
also wrong.
After the change, the short-circuit test was re-done in the
same way as described in the commit that is implementing it.
- From Bjorn Andersson review:
- Improved documentation about over-current and short-circuit
protection in the driver
- Improved maintainability of qcom_labibb_sc_recovery_worker()
- Flipped around check for PBS vreg disabled in for loop of
function labibb_sc_err_handler()
- From Mark Brown (forgotten in v2):
- Changed regulator_{list,map}_voltage_linear_range usages to
regulator_{list,map}_voltage_linear (and fixed regulator
descs to reflect the change).
Changes in v2:
- From Mark Brown review:
- Replaced some if branches with switch statements
- Moved irq get and request in probe function
- Changed short conditionals to full ones
- Removed useless check for ocp_irq_requested
- Fixed issues with YAML documentation
AngeloGioacchino Del Regno (7):
regulator: qcom-labibb: Switch voltage ops from linear_range to linear
regulator: qcom-labibb: Implement current limiting
regulator: qcom-labibb: Implement pull-down, softstart, active
discharge
dt-bindings: regulator: qcom-labibb: Document soft start properties
regulator: qcom-labibb: Implement short-circuit and over-current IRQs
dt-bindings: regulator: qcom-labibb: Document SCP/OCP interrupts
arm64: dts: pmi8998: Add the right interrupts for LAB/IBB SCP and OCP
.../regulator/qcom-labibb-regulator.yaml | 30 +-
arch/arm64/boot/dts/qcom/pmi8998.dtsi | 8 +-
drivers/regulator/qcom-labibb-regulator.c | 720 +++++++++++++++++-
3 files changed, 735 insertions(+), 23 deletions(-)
--
2.30.0
Decrements the reference count of device node and its child node.
Fixes: dfe7a1b058bb ("regulator: AXP20x: Add support for regulators subsystem")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/20210120123313.107640-1-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Short-Circuit Protection (SCP) and Over-Current Protection (OCP) are
very important for regulators like LAB and IBB, which are designed to
provide from very small to relatively big amounts of current to the
device (normally, a display).
Now that this regulator supports both voltage setting and current
limiting in this driver, to me it looked like being somehow essential
to provide support for SCP and OCP, for two reasons:
1. SCP is a drastic measure to prevent damaging "more" hardware in
the worst situations, if any was damaged, preventing potentially
drastic issues;
2. OCP is a great way to protect the hardware that we're powering
through these regulators as if anything bad happens, the HW will
draw more current than expected: in this case, the OCP interrupt
will fire and the regulators will be immediately shut down,
preventing hardware damage in many cases.
Both interrupts were successfully tested in a "sort-of" controlled
manner, with the following methodology:
Short-Circuit Protection (SCP):
1. Set LAB/IBB to 4.6/-1.4V, current limit 200mA/50mA;
2. Connect a 10 KOhm resistor to LAB/IBB by poking the right traces
on a FxTec Pro1 smartphone for a very brief time (in short words,
"just a rapid touch with flying wires");
3. The Short-Circuit protection trips: IRQ raises, regulators get
cut. Recovery OK, test repeated without rebooting, OK.
Over-Current Protection (OCP):
1. Set LAB/IBB to the expected voltage to power up the display of
a Sony Xperia XZ Premium smartphone (Sharp LS055D1SX04), set
current limit to LAB 200mA, IBB 50mA (the values that this
display unit needs are 200/800mA);
2. Boot the kernel: OCP fires. Recovery never happens because
the selected current limit is too low, but that's expected.
Test OK.
3. Set LAB/IBB to the expected current limits for XZ Premium
(LAB 200mA, IBB 800mA), but lower than expected voltage,
specifically LAB 5.4V, IBB -5.6V (instead of 5.6, -5.8V);
4. Boot the kernel: OCP fires. Recovery never happens because
the selected voltage (still in the working range limits)
is producing a current draw of more than 200mA on LAB.
Test OK.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210119174421.226541-6-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Soft start is required to avoid inrush current during LAB ramp-up and
IBB ramp-down, protecting connected hardware to which we supply voltage.
Since soft start is configurable on both LAB and IBB regulators, it
was necessary to add two DT properties, respectively "qcom,soft-start-us"
to control LAB ramp-up and "qcom,discharge-resistor-kohms" to control
the discharge resistor for IBB ramp-down, which obviously brought the
need of implementing a of_parse callback for both regulators.
Finally, also implement pull-down mode in order to avoid unpredictable
behavior when the regulators are disabled (random voltage spikes etc).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210119174421.226541-4-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
LAB and IBB regulators can be current-limited by setting the
appropriate registers, but this operation is granted only after
sending an unlock code for secure access.
Besides the secure access, it would be possible to use the
regmap helper for get_current_limit, as there is no security
blocking reads, but I chose not to as to avoid having a very
big array containing current limits, especially for IBB.
That said, these regulators support current limiting for:
- LAB (pos): 200-1600mA, with 200mA per step (8 steps),
- IBB (neg): 0-1550mA, with 50mA per step (32 steps).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210119174421.226541-3-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The LAB and IBB regulator have just one range and it is useless
to use linear_range ops, as these are used to express multiple
linear ranges.
Switch list_voltage and map_voltage callbacks to *_linear instead.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210119174421.226541-2-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
