IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
ic_dev_xid is only used in __init ic_bootp_recv under IPCONFIG_BOOTP
and __init ic_dynamic under IPCONFIG_DYNAMIC(which is itself defined
with the same IPCONFIG_BOOTP)
This patch fixes the following warning when IPCONFIG_BOOTP is not set:
>> net/ipv4/ipconfig.c:146:15: warning: 'ic_dev_xid' defined but not used [-Wunused-variable]
static __be32 ic_dev_xid; /* Device under configuration */
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: netdev@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes 3 similar bugs where incoming packets might be routed into
wrong non-wildcard tunnels:
1) Consider the following setup:
ip address add 1.1.1.1/24 dev eth0
ip address add 1.1.1.2/24 dev eth0
ip tunnel add ipip1 remote 2.2.2.2 local 1.1.1.1 mode ipip dev eth0
ip link set ipip1 up
Incoming ipip packets from 2.2.2.2 were routed into ipip1 even if it has dst =
1.1.1.2. Moreover even if there was wildcard tunnel like
ip tunnel add ipip0 remote 2.2.2.2 local any mode ipip dev eth0
but it was created before explicit one (with local 1.1.1.1), incoming ipip
packets with src = 2.2.2.2 and dst = 1.1.1.2 were still routed into ipip1.
Same issue existed with all tunnels that use ip_tunnel_lookup (gre, vti)
2) ip address add 1.1.1.1/24 dev eth0
ip tunnel add ipip1 remote 2.2.146.85 local 1.1.1.1 mode ipip dev eth0
ip link set ipip1 up
Incoming ipip packets with dst = 1.1.1.1 were routed into ipip1, no matter what
src address is. Any remote ip address which has ip_tunnel_hash = 0 raised this
issue, 2.2.146.85 is just an example, there are more than 4 million of them.
And again, wildcard tunnel like
ip tunnel add ipip0 remote any local 1.1.1.1 mode ipip dev eth0
wouldn't be ever matched if it was created before explicit tunnel like above.
Gre & vti tunnels had the same issue.
3) ip address add 1.1.1.1/24 dev eth0
ip tunnel add gre1 remote 2.2.146.84 local 1.1.1.1 key 1 mode gre dev eth0
ip link set gre1 up
Any incoming gre packet with key = 1 were routed into gre1, no matter what
src/dst addresses are. Any remote ip address which has ip_tunnel_hash = 0 raised
the issue, 2.2.146.84 is just an example, there are more than 4 million of them.
Wildcard tunnel like
ip tunnel add gre2 remote any local any key 1 mode gre dev eth0
wouldn't be ever matched if it was created before explicit tunnel like above.
All this stuff happened because while looking for a wildcard tunnel we didn't
check that matched tunnel is a wildcard one. Fixed.
Signed-off-by: Dmitry Popov <ixaphire@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ic_dev_xid is only used in ipconfig.c
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: netdev@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The undo code assumes that, upon entering loss recovery, TCP
1) always retransmit something
2) the retransmission never fails locally (e.g., qdisc drop)
so undo_marker is set in tcp_enter_recovery() and undo_retrans is
incremented only when tcp_retransmit_skb() is successful.
When the assumption is broken because TCP's cwnd is too small to
retransmit or the retransmit fails locally. The next (DUP)ACK
would incorrectly revert the cwnd and the congestion state in
tcp_try_undo_dsack() or tcp_may_undo(). Subsequent (DUP)ACKs
may enter the recovery state. The sender repeatedly enter and
(incorrectly) exit recovery states if the retransmits continue to
fail locally while receiving (DUP)ACKs.
The fix is to initialize undo_retrans to -1 and start counting on
the first retransmission. Always increment undo_retrans even if the
retransmissions fail locally because they couldn't cause DSACKs to
undo the cwnd reduction.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem was triggered by these steps:
1) create socket, bind and then setsockopt for add mc group.
mreq.imr_multiaddr.s_addr = inet_addr("255.0.0.37");
mreq.imr_interface.s_addr = inet_addr("192.168.1.2");
setsockopt(sockfd, IPPROTO_IP, IP_ADD_MEMBERSHIP, &mreq, sizeof(mreq));
2) drop the mc group for this socket.
mreq.imr_multiaddr.s_addr = inet_addr("255.0.0.37");
mreq.imr_interface.s_addr = inet_addr("0.0.0.0");
setsockopt(sockfd, IPPROTO_IP, IP_DROP_MEMBERSHIP, &mreq, sizeof(mreq));
3) and then drop the socket, I found the mc group was still used by the dev:
netstat -g
Interface RefCnt Group
--------------- ------ ---------------------
eth2 1 255.0.0.37
Normally even though the IP_DROP_MEMBERSHIP return error, the mc group still need
to be released for the netdev when drop the socket, but this process was broken when
route default is NULL, the reason is that:
The ip_mc_leave_group() will choose the in_dev by the imr_interface.s_addr, if input addr
is NULL, the default route dev will be chosen, then the ifindex is got from the dev,
then polling the inet->mc_list and return -ENODEV, but if the default route dev is NULL,
the in_dev and ifIndex is both NULL, when polling the inet->mc_list, the mc group will be
released from the mc_list, but the dev didn't dec the refcnt for this mc group, so
when dropping the socket, the mc_list is NULL and the dev still keep this group.
v1->v2: According Hideaki's suggestion, we should align with IPv6 (RFC3493) and BSDs,
so I add the checking for the in_dev before polling the mc_list, make sure when
we remove the mc group, dec the refcnt to the real dev which was using the mc address.
The problem would never happened again.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a connected socket we can precompute the flow hash for setting
in skb->hash on output. This is a performance advantage over
calculating the skb->hash for every packet on the connection. The
computation is done using the common hash algorithm to be consistent
with computations done for packets of the connection in other states
where thers is no socket (e.g. time-wait, syn-recv, syn-cookies).
This patch adds sk_txhash to the sock structure. inet_set_txhash and
ip6_set_txhash functions are added which are called from points in
TCP and UDP where socket moves to established state.
skb_set_hash_from_sk is a function which sets skb->hash from the
sock txhash value. This is called in UDP and TCP transmit path when
transmitting within the context of a socket.
Tested: ran super_netperf with 200 TCP_RR streams over a vxlan
interface (in this case skb_get_hash called on every TX packet to
create a UDP source port).
Before fix:
95.02% CPU utilization
154/256/505 90/95/99% latencies
1.13042e+06 tps
Time in functions:
0.28% skb_flow_dissect
0.21% __skb_get_hash
After fix:
94.95% CPU utilization
156/254/485 90/95/99% latencies
1.15447e+06
Neither __skb_get_hash nor skb_flow_dissect appear in perf
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always store in snt_synack the time at which the server received the
first client SYN and attempted to send the first SYNACK.
Recent commit aa27fc501 ("tcp: tcp_v[46]_conn_request: fix snt_synack
initialization") resolved an inconsistency between IPv4 and IPv6 in
the initialization of snt_synack. This commit brings back the idea
from 843f4a55e (tcp: use tcp_v4_send_synack on first SYN-ACK), which
was going for the original behavior of snt_synack from the commit
where it was added in 9ad7c049f0f79 ("tcp: RFC2988bis + taking RTT
sample from 3WHS for the passive open side") in v3.1.
In addition to being simpler (and probably a tiny bit faster),
unconditionally storing the time of the first SYNACK attempt has been
useful because it allows calculating a performance metric quantifying
how long it took to establish a passive TCP connection.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Jerry Chu <hkchu@google.com>
Acked-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some older router implementations still send Fragmentation Needed
errors with the Next-Hop MTU field set to zero. This is explicitly
described as an eventuality that hosts must deal with by the
standard (RFC 1191) since older standards specified that those
bits must be zero.
Linux had a generic (for all of IPv4) implementation of the algorithm
described in the RFC for searching a list of MTU plateaus for a good
value. Commit 46517008e116 ("ipv4: Kill ip_rt_frag_needed().")
removed this as part of the changes to remove the routing cache.
Subsequently any Fragmentation Needed packet with a zero Next-Hop
MTU has been discarded without being passed to the per-protocol
handlers or notifying userspace for raw sockets.
When there is a router which does not implement RFC 1191 on an
MTU limited path then this results in stalled connections since
large packets are discarded and the local protocols are not
notified so they never attempt to lower the pMTU.
One example I have seen is an OpenBSD router terminating IPSec
tunnels. It's worth pointing out that this case is distinct from
the BSD 4.2 bug which incorrectly calculated the Next-Hop MTU
since the commit in question dismissed that as a valid concern.
All of the per-protocols handlers implement the simple approach from
RFC 1191 of immediately falling back to the minimum value. Although
this is sub-optimal it is vastly preferable to connections hanging
indefinitely.
Remove the Next-Hop MTU != 0 check and allow such packets
to follow the normal path.
Fixes: 46517008e116 ("ipv4: Kill ip_rt_frag_needed().")
Signed-off-by: Edward Allcutt <edward.allcutt@openmarket.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in repair-mode and TCP_RECV_QUEUE is set, we end up calling
tcp_push with mss_now being 0. If data is in the send-queue and
tcp_set_skb_tso_segs gets called, we crash because it will divide by
mss_now:
[ 347.151939] divide error: 0000 [#1] SMP
[ 347.152907] Modules linked in:
[ 347.152907] CPU: 1 PID: 1123 Comm: packetdrill Not tainted 3.16.0-rc2 #4
[ 347.152907] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 347.152907] task: f5b88540 ti: f3c82000 task.ti: f3c82000
[ 347.152907] EIP: 0060:[<c1601359>] EFLAGS: 00210246 CPU: 1
[ 347.152907] EIP is at tcp_set_skb_tso_segs+0x49/0xa0
[ 347.152907] EAX: 00000b67 EBX: f5acd080 ECX: 00000000 EDX: 00000000
[ 347.152907] ESI: f5a28f40 EDI: f3c88f00 EBP: f3c83d10 ESP: f3c83d00
[ 347.152907] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 347.152907] CR0: 80050033 CR2: 083158b0 CR3: 35146000 CR4: 000006b0
[ 347.152907] Stack:
[ 347.152907] c167f9d9 f5acd080 000005b4 00000002 f3c83d20 c16013e6 f3c88f00 f5acd080
[ 347.152907] f3c83da0 c1603b5a f3c83d38 c10a0188 00000000 00000000 f3c83d84 c10acc85
[ 347.152907] c1ad5ec0 00000000 00000000 c1ad679c 010003e0 00000000 00000000 f3c88fc8
[ 347.152907] Call Trace:
[ 347.152907] [<c167f9d9>] ? apic_timer_interrupt+0x2d/0x34
[ 347.152907] [<c16013e6>] tcp_init_tso_segs+0x36/0x50
[ 347.152907] [<c1603b5a>] tcp_write_xmit+0x7a/0xbf0
[ 347.152907] [<c10a0188>] ? up+0x28/0x40
[ 347.152907] [<c10acc85>] ? console_unlock+0x295/0x480
[ 347.152907] [<c10ad24f>] ? vprintk_emit+0x1ef/0x4b0
[ 347.152907] [<c1605716>] __tcp_push_pending_frames+0x36/0xd0
[ 347.152907] [<c15f4860>] tcp_push+0xf0/0x120
[ 347.152907] [<c15f7641>] tcp_sendmsg+0xf1/0xbf0
[ 347.152907] [<c116d920>] ? kmem_cache_free+0xf0/0x120
[ 347.152907] [<c106a682>] ? __sigqueue_free+0x32/0x40
[ 347.152907] [<c106a682>] ? __sigqueue_free+0x32/0x40
[ 347.152907] [<c114f0f0>] ? do_wp_page+0x3e0/0x850
[ 347.152907] [<c161c36a>] inet_sendmsg+0x4a/0xb0
[ 347.152907] [<c1150269>] ? handle_mm_fault+0x709/0xfb0
[ 347.152907] [<c15a006b>] sock_aio_write+0xbb/0xd0
[ 347.152907] [<c1180b79>] do_sync_write+0x69/0xa0
[ 347.152907] [<c1181023>] vfs_write+0x123/0x160
[ 347.152907] [<c1181d55>] SyS_write+0x55/0xb0
[ 347.152907] [<c167f0d8>] sysenter_do_call+0x12/0x28
This can easily be reproduced with the following packetdrill-script (the
"magic" with netem, sk_pacing and limit_output_bytes is done to prevent
the kernel from pushing all segments, because hitting the limit without
doing this is not so easy with packetdrill):
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 < S 0:0(0) win 32792 <mss 1460>
+0 > S. 0:0(0) ack 1 <mss 1460>
+0.1 < . 1:1(0) ack 1 win 65000
+0 accept(3, ..., ...) = 4
// This forces that not all segments of the snd-queue will be pushed
+0 `tc qdisc add dev tun0 root netem delay 10ms`
+0 `sysctl -w net.ipv4.tcp_limit_output_bytes=2`
+0 setsockopt(4, SOL_SOCKET, 47, [2], 4) = 0
+0 write(4,...,10000) = 10000
+0 write(4,...,10000) = 10000
// Set tcp-repair stuff, particularly TCP_RECV_QUEUE
+0 setsockopt(4, SOL_TCP, 19, [1], 4) = 0
+0 setsockopt(4, SOL_TCP, 20, [1], 4) = 0
// This now will make the write push the remaining segments
+0 setsockopt(4, SOL_SOCKET, 47, [20000], 4) = 0
+0 `sysctl -w net.ipv4.tcp_limit_output_bytes=130000`
// Now we will crash
+0 write(4,...,1000) = 1000
This happens since ec3423257508 (tcp: fix retransmission in repair
mode). Prior to that, the call to tcp_push was prevented by a check for
tp->repair.
The patch fixes it, by adding the new goto-label out_nopush. When exiting
tcp_sendmsg and a push is not required, which is the case for tp->repair,
we go to this label.
When repairing and calling send() with TCP_RECV_QUEUE, the data is
actually put in the receive-queue. So, no push is required because no
data has been added to the send-queue.
Cc: Andrew Vagin <avagin@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Fixes: ec3423257508 (tcp: fix retransmission in repair mode)
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Acked-by: Andrew Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an UDP application switches from AF_INET to AF_INET6 sockets, we
have a small performance degradation for IPv4 communications because of
extra cache line misses to access ipv6only information.
This can also be noticed for TCP listeners, as ipv6_only_sock() is also
used from __inet_lookup_listener()->compute_score()
This is magnified when SO_REUSEPORT is used.
Move ipv6only into struct sock_common so that it is available at
no extra cost in lookups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have two different ways to handle changes to sk->sk_dst
First way (used by TCP) assumes socket lock is owned by caller, and use
no extra lock : __sk_dst_set() & __sk_dst_reset()
Another way (used by UDP) uses sk_dst_lock because socket lock is not
always taken. Note that sk_dst_lock is not softirq safe.
These ways are not inter changeable for a given socket type.
ipv4_sk_update_pmtu(), added in linux-3.8, added a race, as it used
the socket lock as synchronization, but users might be UDP sockets.
Instead of converting sk_dst_lock to a softirq safe version, use xchg()
as we did for sk_rx_dst in commit e47eb5dfb296b ("udp: ipv4: do not use
sk_dst_lock from softirq context")
In a follow up patch, we probably can remove sk_dst_lock, as it is
only used in IPv6.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Fixes: 9cb3a50c5f63e ("ipv4: Invalidate the socket cached route on pmtu events if possible")
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes build error introduced by commit 1fb6f159fd21c64 (tcp: add
tcp_conn_request):
net/ipv4/tcp_input.c: In function 'pr_drop_req':
net/ipv4/tcp_input.c:5889:130: error: 'struct sock_common' has no member named 'skc_v6_daddr'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
3328715e6c1fc (xfrm4: Add IPsec protocol multiplexer) adds a
duplicate semicolon after the return-statement.
Although it has no negative impact, the second semicolon should be
removed.
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Create tcp_conn_request and remove most of the code from
tcp_v4_conn_request and tcp_v6_conn_request.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add queue_add_hash member to tcp_request_sock_ops so that we can later
unify tcp_v4_conn_request and tcp_v6_conn_request.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mss_clamp member to tcp_request_sock_ops so that we can later
unify tcp_v4_conn_request and tcp_v6_conn_request.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new tcp_request_sock_ops method to unify the IPv4/IPv6
signature for tcp_v[46]_send_synack. This allows us to later unify
tcp_v4_rtx_synack with tcp_v6_rtx_synack and tcp_v4_conn_request with
tcp_v4_conn_request.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More work in preparation of unifying tcp_v4_conn_request and
tcp_v6_conn_request: indirect the init sequence calls via the
tcp_request_sock_ops.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create wrappers with same signature for the IPv4/IPv6 request routing
calls and use these wrappers (via route_req method from
tcp_request_sock_ops) in tcp_v4_conn_request and tcp_v6_conn_request
with the purpose of unifying the two functions in a later patch.
We can later drop the wrapper functions and modify inet_csk_route_req
and inet6_cks_route_req to use the same signature.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the specific IPv4/IPv6 cookie sequence initialization to a new
method in tcp_request_sock_ops in preparation for unifying
tcp_v4_conn_request and tcp_v6_conn_request.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the specific IPv4/IPv6 intializations to a new method in
tcp_request_sock_ops in preparation for unifying tcp_v4_conn_request
and tcp_v6_conn_request.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 016818d07 (tcp: TCP Fast Open Server - take SYNACK RTT after
completing 3WHS) changes the code to only take a snt_synack timestamp
when a SYNACK transmit or retransmit succeeds. This behaviour is later
broken by commit 843f4a55e (tcp: use tcp_v4_send_synack on first
SYN-ACK), as snt_synack is now updated even if tcp_v4_send_synack
fails.
Also, commit 3a19ce0ee (tcp: IPv6 support for fastopen server) misses
the required IPv6 updates for 016818d07.
This patch makes sure that snt_synack is updated only when the SYNACK
trasnmit/retransmit succeeds, for both IPv4 and IPv6.
Cc: Cardwell <ncardwell@google.com>
Cc: Daniel Lee <longinus00@gmail.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the generic plain text packet loggger for ARP packets. It is
based on the ebt_log code. Nevertheless, the output has been modified
to make it consistent with the original xt_LOG output.
This is an example output:
IN=wlan0 OUT= ARP HTYPE=1 PTYPE=0x0800 OPCODE=2 MACSRC=00🆎12:34:55:63 IPSRC=192.168.10.1 MACDST=80:09:12:70:4f:50 IPDST=192.168.10.150
This patch enables packet logging from ARP chains, eg.
nft add rule arp filter input log prefix "input: "
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Before this patch, the nf_loginfo parameter specified the logging
configuration in case the specified default logger was loaded. This
patch updates the semantics of the nf_loginfo parameter in
nf_log_packet() which now indicates the logger that you explicitly
want to use.
Thus, nf_log_packet() is exposed as an unified interface which
internally routes the log message to the corresponding logger type
by family.
The module dependencies are expressed by the new nf_logger_find_get()
and nf_logger_put() functions which bump the logger module refcount.
Thus, you can not remove logger modules that are used by rules anymore.
Another important effect of this change is that the family specific
module is only loaded when required. Therefore, xt_LOG and nft_log
will just trigger the autoload of the nf_log_{ip,ip6} modules
according to the family.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The plain text logging is currently embedded into the xt_LOG target.
In order to be able to use the plain text logging from nft_log, as a
first step, this patch moves the family specific code to the following
files and Kconfig symbols:
1) net/ipv4/netfilter/nf_log_ip.c: CONFIG_NF_LOG_IPV4
2) net/ipv6/netfilter/nf_log_ip6.c: CONFIG_NF_LOG_IPV6
3) net/netfilter/nf_log_common.c: CONFIG_NF_LOG_COMMON
These new modules will be required by xt_LOG and nft_log. This patch
is based on original patch from Arturo Borrero Gonzalez.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add MIB counters for rcvbuferrors in UDP to help diagnose problems.
Signed-off-by: James M Leddy <james.leddy@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error handling in the module init and exit functions can be
shortened to safe us some code.
1/ Remove the code duplications in the init function, jump straight to
the existing cleanup code by adding some labels. Also give the error
message some more value by telling the reason why loading the module has
failed. Furthermore fix the "IPSec" typo -- it should be "IPsec" instead.
2/ Remove the error handling in the exit function as the only legitimate
reason xfrm4_protocol_deregister() might fail is inet_del_protocol()
returning -1. That, in turn, means some other protocol handler had been
registered for this very protocol in the meantime. But that essentially
means we haven't been handling that protocol any more, anyway. What it
definitely means not is that we "can't deregister tunnel". Therefore
just get rid of that bogus warning. It's plain wrong.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When IP route cache had been removed in linux-3.6, we broke assumption
that dst entries were all freed after rcu grace period. DST_NOCACHE
dst were supposed to be freed from dst_release(). But it appears
we want to keep such dst around, either in UDP sockets or tunnels.
In sk_dst_get() we need to make sure dst refcount is not 0
before incrementing it, or else we might end up freeing a dst
twice.
DST_NOCACHE set on a dst does not mean this dst can not be attached
to a socket or a tunnel.
Then, before actual freeing, we need to observe a rcu grace period
to make sure all other cpus can catch the fact the dst is no longer
usable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dormando <dormando@rydia.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been marked as deprecated for quite some time and the NFLOG
target replacement has been also available since 2006.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If there is an MSS change (or misbehaving receiver) that causes a SACK
to arrive that covers the end of an skb but is less than one MSS, then
tcp_match_skb_to_sack() was rounding up pkt_len to the full length of
the skb ("Round if necessary..."), then chopping all bytes off the skb
and creating a zero-byte skb in the write queue.
This was visible now because the recently simplified TLP logic in
bef1909ee3ed1c ("tcp: fixing TLP's FIN recovery") could find that 0-byte
skb at the end of the write queue, and now that we do not check that
skb's length we could send it as a TLP probe.
Consider the following example scenario:
mss: 1000
skb: seq: 0 end_seq: 4000 len: 4000
SACK: start_seq: 3999 end_seq: 4000
The tcp_match_skb_to_sack() code will compute:
in_sack = false
pkt_len = start_seq - TCP_SKB_CB(skb)->seq = 3999 - 0 = 3999
new_len = (pkt_len / mss) * mss = (3999/1000)*1000 = 3000
new_len += mss = 4000
Previously we would find the new_len > skb->len check failing, so we
would fall through and set pkt_len = new_len = 4000 and chop off
pkt_len of 4000 from the 4000-byte skb, leaving a 0-byte segment
afterward in the write queue.
With this new commit, we notice that the new new_len >= skb->len check
succeeds, so that we return without trying to fragment.
Fixes: adb92db857ee ("tcp: Make SACK code to split only at mss boundaries")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Ilpo Jarvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ir_mark initialization is done for both TCP v4 and v6, move it in the
common tcp_openreq_init function.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is overwritten by the child socket assignment before
it ever gets used.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its too easy to add thousand of UDP sockets on a particular bucket,
and slow down an innocent multicast receiver.
Early demux is supposed to be an optimization, we should avoid spending
too much time in it.
It is interesting to note __udp4_lib_demux_lookup() only tries to
match first socket in the chain.
10 is the threshold we already have in __udp4_lib_lookup() to switch
to secondary hash.
Fixes: 421b3885bf6d5 ("udp: ipv4: Add udp early demux")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: David Held <drheld@google.com>
Cc: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Fix to a problem observed when losing a FIN segment that does not
contain data. In such situations, TLP is unable to recover from
*any* tail loss and instead adds at least PTO ms to the
retransmission process, i.e., RTO = RTO + PTO.
Signed-off-by: Per Hurtig <per.hurtig@kau.se>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/core/rtnetlink.c
net/core/skbuff.c
Both conflicts were very simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to gro_postpull_rcsum for GRO to work with checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In skb_checksum complete, if we need to compute the checksum for the
packet (via skb_checksum) save the result as CHECKSUM_COMPLETE.
Subsequent checksum verification can use this.
Also, added csum_complete_sw flag to distinguish between software and
hardware generated checksum complete, we should always be able to trust
the software computation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some tunnels (though only vti as for now) can use i_key just for internal use:
for example vti uses it for fwmark'ing incoming packets. So raw i_key value
shouldn't be treated as a distinguisher for them. ip_tunnel_key_match exists for
cases when we want to compare two ip_tunnel_parms' i_keys.
Example bug:
ip link add type vti ikey 1 local 1.0.0.1 remote 2.0.0.2
ip link add type vti ikey 2 local 1.0.0.1 remote 2.0.0.2
spawned two tunnels, although it doesn't make sense.
Signed-off-by: Dmitry Popov <ixaphire@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip tunnel add remote 10.2.2.1 local 10.2.2.2 mode vti ikey 1 okey 2
translates to p->iflags = VTI_ISVTI|GRE_KEY and p->i_key = 1, but GRE_KEY !=
TUNNEL_KEY, so ip_tunnel_ioctl would set i_key to 0 (same story with o_key)
making us unable to create vti tunnels with [io]key via ip tunnel.
We cannot simply translate GRE_KEY to TUNNEL_KEY (as GRE module does) because
vti_tunnels with same local/remote addresses but different ikeys will be treated
as different then. So, imo the best option here is to move p->i_flags & *_KEY
check for vti tunnels from ip_tunnel.c to ip_vti.c and to think about [io]_mark
field for ip_tunnel_parm in the future.
Signed-off-by: Dmitry Popov <ixaphire@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4_{update_pmtu,redirect} were called with tunnel's ifindex (t->dev is a
tunnel netdevice). It caused wrong route lookup and failure of pmtu update or
redirect. We should use the same ifindex that we use in ip_route_output_* in
*tunnel_xmit code. It is t->parms.link .
Signed-off-by: Dmitry Popov <ixaphire@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to require forcing device down on a Ethernet GRE (gretap)
tunnel to change the MAC address.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_fragment can be called from process context (from tso_fragment).
Add a new gfp parameter to allow it to preserve atomic memory if
possible.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull cgroup updates from Tejun Heo:
"A lot of activities on cgroup side. Heavy restructuring including
locking simplification took place to improve the code base and enable
implementation of the unified hierarchy, which currently exists behind
a __DEVEL__ mount option. The core support is mostly complete but
individual controllers need further work. To explain the design and
rationales of the the unified hierarchy
Documentation/cgroups/unified-hierarchy.txt
is added.
Another notable change is css (cgroup_subsys_state - what each
controller uses to identify and interact with a cgroup) iteration
update. This is part of continuing updates on css object lifetime and
visibility. cgroup started with reference count draining on removal
way back and is now reaching a point where csses behave and are
iterated like normal refcnted objects albeit with some complexities to
allow distinguishing the state where they're being deleted. The css
iteration update isn't taken advantage of yet but is planned to be
used to simplify memcg significantly"
* 'for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (77 commits)
cgroup: disallow disabled controllers on the default hierarchy
cgroup: don't destroy the default root
cgroup: disallow debug controller on the default hierarchy
cgroup: clean up MAINTAINERS entries
cgroup: implement css_tryget()
device_cgroup: use css_has_online_children() instead of has_children()
cgroup: convert cgroup_has_live_children() into css_has_online_children()
cgroup: use CSS_ONLINE instead of CGRP_DEAD
cgroup: iterate cgroup_subsys_states directly
cgroup: introduce CSS_RELEASED and reduce css iteration fallback window
cgroup: move cgroup->serial_nr into cgroup_subsys_state
cgroup: link all cgroup_subsys_states in their sibling lists
cgroup: move cgroup->sibling and ->children into cgroup_subsys_state
cgroup: remove cgroup->parent
device_cgroup: remove direct access to cgroup->children
memcg: update memcg_has_children() to use css_next_child()
memcg: remove tasks/children test from mem_cgroup_force_empty()
cgroup: remove css_parent()
cgroup: skip refcnting on normal root csses and cgrp_dfl_root self css
cgroup: use cgroup->self.refcnt for cgroup refcnting
...
