IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Commit 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux
GPIO translation") has made the cherryview gpio numbers sparse, to get
a 1:1 mapping between ACPI pin numbers and gpio numbers in Linux.
This has greatly simplified things, but the code setting the
irq_valid_mask was not updated for this, so the valid mask is still in
the old "compressed" numbering with the gaps in the pin numbers skipped,
which is wrong as irq_valid_mask needs to be expressed in gpio numbers.
This results in the following error on devices using pin 24 (0x0018) on
the north GPIO controller as an ACPI event source:
[ 0.422452] cherryview-pinctrl INT33FF:01: Failed to translate GPIO to IRQ
This has been reported (by email) to be happening on a Caterpillar CAT T20
tablet and I've reproduced this myself on a Medion Akoya e2215t 2-in-1.
This commit uses the pin number instead of the compressed index into
community->pins to clear the correct bits in irq_valid_mask for GPIOs
using GPEs for interrupts, fixing these errors and in case of the
Medion Akoya e2215t also fixing the LID switch not working.
Cc: stable@vger.kernel.org
Fixes: 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When consumer requests a pin, in order to be on the safest side,
we switch it first to GPIO mode followed by immediate transition
to the input state. Due to posted writes it's luckily to be a single
I/O transaction.
However, if firmware or boot loader already configures the pin
to the GPIO mode, user expects no glitches for the requested pin.
We may check if the pin is pre-configured and leave it as is
till the actual consumer toggles its state to avoid glitches.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Depends-on: f5a26acf0162 ("pinctrl: intel: Initialize GPIO properly when used through irqchip")
Cc: stable@vger.kernel.org
Cc: fei.yang@intel.com
Reported-by: Oliver Barta <oliver.barta@aptiv.com>
Reported-by: Malin Jonsson <malin.jonsson@ericsson.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For the new Spreadtrum pin controller, it expands 6bits to describe the
pin sleep mode with adding one CM4_SLEEP mode, which means the pin sleep
related configuration will be loaded automatically by hardware when the
CM4 system goes into deep sleep mode.
Signed-off-by: Bruce Chen <bruce.chen@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/8ae52263b0625c416461821c457e6789b67170b6.1571228451.git.baolin.wang@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AST2600 EMMC support 3 types DAT bus sizes (1, 4 and 8-bit),
corresponding to 3 groups: EMMCG1, EMMCG4 and EMMCG8
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-8-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When UART13G1 is set the pinmux configuration in SCU4B8 for UART13G0
should be cleared.
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
[AJ: Tweak commit message]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-7-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signal descriptors can represent multi-bit bitfields and so have
explicit "enable" and "disable" states. However many descriptor
instances only describe a single bit, and so the SIG_DESC_SET() macro is
provides an abstraction for the single-bit cases: Its expansion
configures the "enable" state to set the bit and "disable" to clear.
SIG_DESC_CLEAR() was introduced to provide a similar single-bit
abstraction for for descriptors to clear the bit of interest. However
its behaviour was defined as the literal inverse of SIG_DESC_SET() - the
impact is the bit of interest is set in the disable path. This behaviour
isn't intuitive and doesn't align with how we want to use the macro in
practice, so make it clear the bit for both the enable and disable
paths.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-6-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The documentation to configure I3C3/FSI1 and I3C4/FSI2 was initially
unclear.
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
[AJ: Tweak commit message, resolve rebase conflicts]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-5-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2C function the pin participated in was incorrectly named SDA14
which lead to a failure to mux:
[ 6.884344] No function I2C14 found on pin 7 (7). Found signal(s) MACLINK4, SDA14, GPIOA7 for function(s) MACLINK4, SDA14, GPIOA7
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-4-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pins crept in that weren't ordered in the list.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-3-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191014111154.9731-2-linus.walleij@linaro.org
The latent IRQs are IRQs that have occurred when the system
was down in deep sleep and the GPIO block was powered off.
The PRCMU (power reset and control unit) knows which GPIO
line offset fired an IRQ to wake the system up (if so
desired) and this second IRQ was used to replay the action
when the system came back online after suspend().
This is now known to be the wrong approach to solve this
problem: in a patch series Lina Iyer has suggested to
instead make it possible to model the IRQs as hierarchical
with double parents.
Also the current device trees do not contain the right
information to make this code work, the latent IRQ is not
specified nowadays giving noise like this in the console:
[ 0.612168] gpio 8012e000.gpio: IRQ index 1 not found
[ 0.622523] gpio 8012e080.gpio: IRQ index 1 not found
Let's delete the latent IRQ code and reimplement it properly
when we need it.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191014111154.9731-1-linus.walleij@linaro.org
When an STMFX IO is used as interrupt through the interrupt-controller
binding, the STMFX driver should configure this IO as input. Default
value of STMFX IO direction is input, but if the IO is used as output
before the interrupt use, it will not work without these callbacks.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20191009091606.17283-1-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pinctrl driver to support pin configuration with the
pinctrl framework on MSM8976, MSM8956, APQ8056, APQ8076.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20191005105936.31216-2-kholk11@gmail.com
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Zhou Yanjie <zhouyanjie@zoho.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191001133209.17164-1-linus.walleij@linaro.org
Add support for the PM6150 and PM6150L GPIO support to the
Qualcomm PMIC GPIO binding.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Link: https://lore.kernel.org/r/1570188039-22122-1-git-send-email-kgunda@codeaurora.org
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: James Hartley <james.hartley@sondrel.com>
Link: https://lore.kernel.org/r/20191001214536.18477-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191002121550.16104-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20191002114454.9684-1-linus.walleij@linaro.org
The function should be spdifib, fix this typo.
Fixes: 423ddc580b13 ("pinctrl: berlin: add the as370 SoC pinctrl driver")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20191011154321.44f08f9a@xhacker.debian
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191002113819.4927-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion: the ST pin controller errors out of adding a
irqchip if the interrupt is invalid or missing or if the
irqmux is not present: the irqchip should not be added
if either of these errors happen, so rewrite the code to
deal with that. Keep the exit path where the gpio_chip
is added no matter what the status of the irq is.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191001135147.29416-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion: at91 is a little bit special since it registers
up to 3 gpio_chips with the same parent handler, but just
passing girq->parent_handler and the parent on the first
of them should cut it.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20191001130645.8350-1-linus.walleij@linaro.org
This patch allows PINMUX_IPSR_PHYS() to set bits in GPSR.
When assigning function to pin, GPSR should be set to peripheral
function.
For example when using SCL3, GPSR2 bit7 (PWM1_A pin) should be set to
peripheral function.
Signed-off-by: Keiya Nobuta <nobuta.keiya@fujitsu.com>
Link: https://lore.kernel.org/r/20191008060112.29819-1-nobuta.keiya@fujitsu.com
Fixes: 50d1ba1764b3e00a ("pinctrl: sh-pfc: Add physical pin multiplexing helper macros")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Don't populate the array reg_drive on the stack but instead make it
static. Makes the object code smaller by 32 bytes.
Before:
text data bss dec hex filename
31991 15696 0 47687 ba47 drivers/pinctrl/pinctrl-rzn1.o
After:
text data bss dec hex filename
31863 15792 0 47655 ba27 drivers/pinctrl/pinctrl-rzn1.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20191007140559.11840-1-colin.king@canonical.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This includes two fixes for Intel pinctrl drivers:
- Fix warning about shared irqchip
- Restore Strago DMI workaround for all versions
-----BEGIN PGP SIGNATURE-----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=xjVF
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-fixes-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl fixes for v5.4
This includes two fixes for Intel pinctrl drivers:
- Fix warning about shared irqchip
- Restore Strago DMI workaround for all versions
The configuration registers for the LED group have inverted
polarity, which puts the GPIO into open-drain state when used in
GPIO mode. Switch to '0' for GPIO and '1' for LED modes.
Fixes: 87466ccd9401 ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx")
Signed-off-by: Patrick Williams <alpawi@amazon.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191001155154.99710-1-alpawi@amazon.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dev_get_platdata(&pdev->dev) returns a pointer on struct stmfx_pinctrl,
not on struct stmfx (platform_set_drvdata(pdev, pctl); in probe).
Pointer on struct stmfx is stored in driver data of pdev parent (in probe:
struct stmfx *stmfx = dev_get_drvdata(pdev->dev.parent);).
Fixes: 1490d9f841b1 ("pinctrl: Add STMFX GPIO expander Pinctrl/GPIO driver")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20191004122342.22018-1-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_get_irq() can return an error code. Allow for this when getting
the irq.
Fixes: 6f265e5d4da7 ("pinctrl: bcm-iproc: Pass irqchip when adding gpiochip")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191003000310.17099-2-chris.packham@alliedtelesis.co.nz
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the dev_name(dev) for the irqc->name so that we get unique names
when we have multiple instances of this driver.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191003000310.17099-3-chris.packham@alliedtelesis.co.nz
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl->functions[] array has pinctrl->num_functions elements and
the pinctrl->groups[] array is the same way. These are set in
ns2_pinmux_probe(). So the > comparisons should be >= so that we don't
read one element beyond the end of the array.
Fixes: b5aa1006e4a9 ("pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190926081426.GB2332@mwanda
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This convert the BCM IPROC driver to use the SPDX header
for indicating GPL v2.0 only licensing.
Cc: Pramod Kumar <pramodku@broadcom.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Link: https://lore.kernel.org/r/20191002130217.4491-1-linus.walleij@linaro.org
The 37xx configuration registers are only 32 bits long, so
pins 32-35 spill over into the next register. The calculation
for the register address was done, but the bitmask was not, so
any configuration to pin 32 or above resulted in a bitmask that
overflowed and performed no action.
Fix the register / offset calculation to also adjust the offset.
Fixes: 5715092a458c ("pinctrl: armada-37xx: Add gpio support")
Signed-off-by: Patrick Williams <alpawi@amazon.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191001154634.96165-1-alpawi@amazon.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The helper pinctrl_dt_has_hogs() was introduced in
99e4f67508e1 (pinctrl: core: Use delayed work for hogs), but the sole
use then got removed shortly after in 950b0d91dc10 (pinctrl: core: Fix
regression caused by delayed work for hogs).
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20190923142005.5632-1-linux@rasmusvillemoes.dk
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a comment about why the call to of_match_node() cannot be replaced
by of_device_get_match_data(). This will hopefully prevent people from
attempting to clean this up in the future.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20190923095400.GA11084@ulmo
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The call to pinctrl_count_index_with_args checks for a -EINVAL return
however this function calls pinctrl_get_list_and_count and this can
return -ENOENT. Rather than check for a specific error, fix this by
checking for any error return to catch the -ENOENT case.
Addresses-Coverity: ("Improper use of negative")
Fixes: 003910ebc83b ("pinctrl: Introduce TI IOdelay configuration driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190920122030.14340-1-colin.king@canonical.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that the GPIO core has support for hierarchical IRQ chips, convert
Qualcomm's ssbi-gpio over to use these new helpers to reduce duplicated
code across drivers.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Link: https://lore.kernel.org/r/20190914111010.24384-1-masneyb@onstation.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When populating the pinctrl mapping table entries for a device, the
'dev_name' field for each entry is initialised to point directly at the
string returned by 'dev_name()' for the device and subsequently used by
'create_pinctrl()' when looking up the mappings for the device being
probed.
This is unreliable in the presence of calls to 'dev_set_name()', which may
reallocate the device name string leaving the pinctrl mappings with a
dangling reference. This then leads to a use-after-free every time the
name is dereferenced by a device probe:
| BUG: KASAN: invalid-access in strcmp+0x20/0x64
| Read of size 1 at addr 13ffffc153494b00 by task modprobe/590
| Pointer tag: [13], memory tag: [fe]
|
| Call trace:
| __kasan_report+0x16c/0x1dc
| kasan_report+0x10/0x18
| check_memory_region
| __hwasan_load1_noabort+0x4c/0x54
| strcmp+0x20/0x64
| create_pinctrl+0x18c/0x7f4
| pinctrl_get+0x90/0x114
| devm_pinctrl_get+0x44/0x98
| pinctrl_bind_pins+0x5c/0x450
| really_probe+0x1c8/0x9a4
| driver_probe_device+0x120/0x1d8
Follow the example of sysfs, and duplicate the device name string before
stashing it away in the pinctrl mapping entries.
Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: Elena Petrova <lenaptr@google.com>
Tested-by: Elena Petrova <lenaptr@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20191002124206.22928-1-will@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement .get_multiple and .set_multiple to allow reading or setting
multiple pins simultaneously. Pins in the same bank will all be switched at
the same time, improving synchronization and performances.
Keep the driver future proof by allowing its use on 64bits platforms if
they ever appear with this IP and we end up with a mismatch between
ATMEL_PIO_NPINS_PER_BANK and BITS_PER_LONG.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20190918113657.25998-1-alexandre.belloni@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Several functions use for_each_child_of_node() loop with a break to find
a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes: 9a2c1c3b91aa ("pinctrl: samsung: Allow grouping multiple pinmux/pinconf nodes")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In s3c64xx_eint_eint0_init() the for_each_child_of_node() loop is used
with a break to find a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes: 61dd72613177 ("pinctrl: Add pinctrl-s3c64xx driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In s3c24xx_eint_init() the for_each_child_of_node() loop is used with a
break to find a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes: af99a7507469 ("pinctrl: Add pinctrl-s3c24xx driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
