IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Add the power supply capacity level property, it corresponds to
POWER_SUPPLY_CAPACITY_LEVEL_*.
It also utilizes the precision voltage detector function module
to catch the low battery voltage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The power supply type property is varying as the external power
supply changes. It is not a constant.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add the charger status change interrupt support, it will report
the power supply changed event.
This interrupt is generated by one of the conditions as below:
- the state machine jumps out of or into the EOC state
- the CHGIN input voltage goes out of or into the valid range.
- the battery temperature goes out of or into the valid range.
- the PRECHARGE time-out occurs.
- the total charge time-out occurs.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
When get the property, first check the charger state machine,
then check the status bit to decide what value is assigned to
the corresponding property.
Retain the SUSCHG bit of REG 0x71 when configure the timers to
avoid losting the charger suspending info after boot.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Remove "battery_temperature" member, it is redundant, it is the
hardware's responsibility to handle TH pin properly.
It is unnecessary to use the dt property to check if there is
a battery temperature monitor or not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since the act8945a_charger is regarded as a sub-device, all properties will
be assigned to its own device node. All properties can be achieved from its
own node, instead of from its parent device.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
When the charger is missing (disconnected), it is safe to assume that
the charger chip is no charging.
This is especially relevant when a status GPIO is present and the
charger is getting disconnected. bq24735_charger_is_charging will be
triggered due to the interrupt then, it will attempt to read whether it
is charging through i2c, which will fail as the charger is disconnected.
This also fixes that specific issue.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact. The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "monitor_wqueue" is used to monitor the battery
status. It has been identity converted.
It queues multiple work items viz &di->monitor_work,
&di->set_charged_work, which require execution ordering.
Hence, alloc_workqueue has been used to replace the
deprecated create_singlethread_workqueue instance.
WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "fg_wq" is used for running the FG algorithm periodically.
It has been identity converted.
It has multiple work items viz fg_periodic_work, fg_low_bat_work,
fg_reinit_work, fg_work, fg_acc_cur_work and fg_check_hw_failure_work,
which require execution ordering. Hence, a dedicated ordered workqueue
has been used here.
The WQ_MEM_RECLAIM flag has been set to guarantee forward progress under
memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The workqueue "wq" is used for handling battery related tasks.
It has a single work item viz &mb->update and hence it doesn't require
execution ordering. Hence, alloc_workqueue has been used to replace the
deprecated create_singlethread_workqueue instance.
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure.
Since there is a single work item, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "charger_wq" is used for the IRQs and checking HW state of
the charger. It has been identity converted.
It has multiple work items viz usb_charger_attached_work, kick_wd_work,
check_vbat_work, check_hw_failure_work, usb_charger_attached_work,
ac_work, ac_charger_attached_work, attach_work and check_usbchgnotok_work,
which require execution ordering. Hence, a dedicated ordered workqueue
has been used here.
The WQ_MEM_RECLAIM flag has also been set to ensure
forward progress under memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The workqueue "monitor_wqueue" is used to monitor the PMIC battery status.
It queues a single work item (pbi->monitor_battery) and hence doesn't
require ordering. Hence, alloc_workqueue has been used to replace the
deprecated create_singlethread_workqueue instance.
Since PMIC battery status needs to be monitored for any change, the
WQ_MEM_RECLAIM flag has been set to ensure forward progress under memory
pressure.
Since there is a single work item, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "charger_wq" is used for running all the charger related
tasks. This involves charger detection, checking for HW failure and HW
status. This workqueue has been identity converted.
It queues multiple workitems viz &pm2->check_main_thermal_prot_work,
&pm2->check_hw_failure_work, &pm2->ac_work. Hence, the deprecated
create_singlethread_workqueue() instance has been replaced with a
dedicated ordered workqueue.
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The workqueue "btemp_wq" is used for measuring the temperature
periodically. It queues a single workitem (btemp_periodic_work) and
hence doesn't require ordering. Thus, the deprecated
create_singlethread_workqueue() instance has been replaced with
alloc_workqueue().
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure.
Since there is a single work item, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "chargalg_wq" is used for running the charging algorithm.
It has multiple workitems viz &di->chargalg_periodic_work,
&di->chargalg_wd_work, &di->chargalg_work per abx500_chargalg, which
require ordering. It has been identity converted.
Also, WQ_MEM_RECLAIM has been set to ensure forward progress under
memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Battery capacity level is a standard feature of sbs battery
That can be used to tell what the remainig battery capacity is, and
can tell if the battery has not been calibrated/initialized, which makes
the capacity and charging/discharging percentages invalid.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use devm_power_supply_register instead of power_supply_register.
Remove call to power_supply_unregister.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Currently the battery detect gpio can not be used with a chained interrupt
controller that requires threaded irq handlers. Use threaded irq instead.
In addition this was not going to be working at present because
chip->power_supply is assigned after the request irq call.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use devm_kzalloc to allow memory to be freed automatically on
driver probe failure or removal.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The bq27000 and bq27010 have a single byte FLAGS register.
Other gauges have 16 bit FLAGS registers.
For reading the FLAGS register it is sufficient to read the single
register instead of reading RSOC at the next higher address as
well and then ignore the high byte.
This does not change functionality but optimizes i2c and hdq
traffic.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Make use of IRQ resources defined in tps65217 mfd code. If they are valid
we use them instead separate poll task, in order to define AC power state.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This moves all power supply drivers from drivers/power/
to drivers/power/supply/. The intention is a cleaner
source tree, since drivers/power/ also contains frameworks
unrelated to power supply, like adaptive voltage scaling.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
