IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
I2C transfer were using dynamic stack allocation. Get rid of it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
PER/UCB statistics are collected once on each 1 second.
However, it doesn't provide the total number of packets
needed to calculate PER.
Yet, as we know the bit rate, it is possible to estimate
such number. So, do it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
On dib8000, the BER statistics are updated on every 1.25e6 bits.
Adjust the code to only update the statistics after having it
done.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
On dib8000, the block error count is a monotonic 32 bits register.
With DVBv5 stats, we use a 64 bits counter, that it is reset
when a new channel is tuned.
Change the UCB counting start from 0 and to be returned with
64 bits, just like the API requests.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Use multiple linear segments to better interpolate the dBm
for the signal strength.
The table that converts from linear strength to dB was
empirically determinated with the help of a signal generator
(DTA-2111).
The entries from -35dBm to -22.5dBm were taken using just
the signal generator and the board.
For the entries from -36dBm to -51dBm, a 16 dB tap was used,
in order to extend its range.
Signals below to -51dBm are just linearly interpolated.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Better to have Signal strength in dB.
This takes a very rough estimation for the signal strength,
that was calibrated using a Dektec DTA-2111 Gold RF generator
and a Pixelview dib8076 stick.
It estimates the signal strength using a linear equation where:
- the max is -22.5 dBm, with returns 55953
- the min is -35.0 dBm, with returns 50110
With -22dBm, the signal strengh is returned as 65535.
Unfortunately, the min strength generated with DTA-2111 is
-35dBm.
It should be noticed that approximating it by a linear equation
is not right. I should probably be splitting it into 0.5 dB
linear segments, in order to get a higher precision, just like
it is done on mb86a20s, but that would force me to add some
attenuators, in order to get dB levels below -35dBm, which is,
btw, strong enough to get signal lock.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
The advantage of DVBv5 stats is that it allows adding proper
scales to all measures. use it for this frontend.
This patch adds a basic set of stats, basically cloning what's already
provided by DVBv3 API. Latter patches will improve it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
On ISDB-T, the valid values for interleaving are 0, 1, 2 and 4.
While the first 3 are properly reported, the last one is reported
as 3 instead. Fix it.
Tested with a Dektec DTA-2111 RF generator.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
The logic that detects if auto search mode should be used is too
complex.
Also, it doesn't cover all cases, as the dib8000_tune logic
requires either auto mode or a fully specified manual mode.
So, move it to a separate function and add some extra debug
data to help identifying when it falled back to auto mode,
because the manual settings are invalid.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Both dvbv5-scan and dvbv5-zap tools call FE_GET_PROPERTY inside the
loop that checks for stats. If the frontend doesn't support DVBv5, it
falls back to call the DVBv5 stats APIs(FE_READ_BER, FE_READ_SIGNAL,
FE_READ_SNR and FE_READ_UNCORRECTED_BLOCKS).
A call to FE_GET_PROPERTY makes dvb-frontend core to call get_frontend().
However, due to a race condition on dib8000 between dib8000_get_frontend
and dib8000_tune, if get_frontend occurs too early, it causes the
tune state machine to fail and not get any lock.
This patch adds a workaround code that makes get_frontend() to just
return if none of the frontends have a SYNC. This change fixed the issue
with dvbv5-scan/dvbv5-zap, but a fine-tuned logic might be needed in
the future, when we implement DVBv5 stats on this frontend.
The procedure to test the bug and the fix is the one below:
1) tune into a non-existing frequency with:
$ dvbv5-zap -I dvbv5 -c non_existing_freqs -m 679142857 -t3
2) tune/lock into an existing frequency with:
$ dvbv5-zap -I dvbv5 -c isdb-test -m 479142857
or
$ dvbv5-scan isdb-test
In this case, 679 MHz carrier doesn't exist. Only 479 MHz does.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
As the dvb-frontend kthread can be called anytime, it can race
with some get status ioctl. So, it seems better to avoid one to
race with the other while reading a 32 bits register.
I can't see any other reason for having a mutex there at I2C, except
to provide such kind of protection, as the I2C core already has a
mutex to protect I2C transfers.
Note: instead of this approach, it could eventually remove the dib8000
specific mutex for it, and either group the 4 ops into one xfer or
to manually control the I2C mutex. The main advantage of the current
approach is that the changes are smaller and more puntual.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Commit 173a64cb3fcf broke support for some dib807x versions.
Fix it by providing backward compatibility with the older versions.
[mkrufky@linuxtv.org: conflict handling and CodingStyle fixes]
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Merge the media fixes merged upstream for v3.13-rc4
* upstream-fixes: (30 commits)
[media] videobuf2-dma-sg: fix possible memory leak
[media] vb2: regression fix: always set length field.
[media] mt9p031: Include linux/of.h header
[media] rtl2830: add parent for I2C adapter
[media] media: marvell-ccic: use devm to release clk
[media] ths7303: Declare as static a private function
[media] em28xx-video: Swap release order to avoid lock nesting
[media] usbtv: Add support for PAL video source
[media] media_tree: Fix spelling errors
[media] videobuf2: Add support for file access mode flags for DMABUF exporting
[media] radio-shark2: Mark shark_resume_leds() inline to kill compiler warning
[media] radio-shark: Mark shark_resume_leds() inline to kill compiler warning
[media] af9035: unlock on error in af9035_i2c_master_xfer()
[media] af9033: fix broken I2C
[media] v4l: omap3isp: Don't check for missing get_fmt op on remote subdev
[media] af9035: fix broken I2C and USB I/O
[media] wm8775: fix broken audio routing
[media] marvell-ccic: drop resource free in driver remove
[media] tef6862/radio-tea5764: actually assign clamp result
[media] cx231xx: use after free on error path in probe
...
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch should fix/enhance the set_voltage function for
the cx24117 demodulator.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the complete list of all the commands known
for the cx24117 demodulator.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver did not work anymore since I2C has gone broken due
to recent commit:
commit 37ebaf6891ee81687bb558e8375c0712d8264ed8
[media] dvb-frontends: Don't use dynamic static allocation
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable@vger.kernel.org
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/stv090x.c:750:1: warning: 'stv090x_write_regs.constprop.6' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/stv0367.c:791:1: warning: 'stv0367_writeregs.constprop.4' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/stb0899_drv.c:540:1: warning: 'stb0899_write_regs' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/af9013.c:77:1: warning: 'af9013_wr_regs_i2c' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/af9033.c:188:1: warning: 'af9033_wr_reg_val_tab' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/af9033.c:68:1: warning: 'af9033_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/bcm3510.c:230:1: warning: 'bcm3510_do_hab_cmd' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/cxd2820r_core.c:84:1: warning: 'cxd2820r_rd_regs_i2c.isra.1' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/rtl2830.c:56:1: warning: 'rtl2830_wr' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/rtl2832.c:187:1: warning: 'rtl2832_wr' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/tda10071.c:52:1: warning: 'tda10071_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/tda10071.c:84:1: warning: 'tda10071_rd_regs' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/bcm3510.c:230:1: warning: 'bcm3510_do_hab_cmd' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/itd1000.c:69:1: warning: 'itd1000_write_regs.constprop.0' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/mt312.c:126:1: warning: 'mt312_write' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/nxt200x.c:111:1: warning: 'nxt200x_writebytes' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/stb6100.c:216:1: warning: 'stb6100_write_reg_range.constprop.3' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/stv6110.c:98:1: warning: 'stv6110_write_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/stv6110x.c:85:1: warning: 'stv6110x_write_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/tda18271c2dd.c:147:1: warning: 'WriteRegs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/zl10039.c:119:1: warning: 'zl10039_write' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/s5h1420.c:851:1: warning: 's5h1420_tuner_i2c_tuner_xfer' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer.
In the specific case of this frontend, only ttpci uses it. The maximum
number of messages there is two, on I2C read operations. As the logic
can add an extra operation, change the size to 3.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use R820T config for R828D too as those are about same tuner.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drxk_hard.c:1086:62: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxk_hard.c:2784:63: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drxd_hard.c:1017:70: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:1038:69: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:2836:33: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:2972:30: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These aren't necessary after switch and while statements.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch will fix the situation where the mutex was left in a
locked state if for some reason the FE init failed.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the cx24117 dual DVB-S/S2 frontend.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Changeset 9e8da9e8 added a parameter to specify the frequency
divisor, used by the driver. However, not all places are passing
this parameter. So, preserve the previous default, to avoid breaking
the existing drivers.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the tuner part of the ds3000 driver was split to share code with the m88rs2000 driver, the ts2020 driver used
the frequency divider value from the m88rs2000 driver. However the ds3000 driver requires a different value, and this
resulted in some frequecies being invisible to the tuner. This patch adds back in the value needed for the ds3000 driver
and configured as an option in the dw2102 frontend driver.
It may also apply to su3000 devices, which use the same ds3000 driver, but for now it is only applied to the s660 device.
Signed-off-by: John Horan <knasher@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Make sure that a format string cannot accidentally
leak into the printk buffer.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SIZEOF_ARRAY is not used (anymore). Besides, ARRAY_SIZE, defined in
include/linux/kernel.h, should be used rather than explicitly coding some
variant of it.
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reading firmware status register to detect whether firmware is
running or not didn't work 100% reliably. That register was
likely set by firmware itself which means it could not contain
reasonable values until firmware is up and running. Usually it
just worked as some garbage value was returned accidentally but it
appears that in some cases returned garbage value was 0x00 which
was considered "firmware is up and running" by the driver and
firmware loading was skipped leaving device to non-working state.
Fix problem by removing unreliable check and let the driver keep
count whether firmware is loaded or not.
Signed-off-by: Andreas Matthies <a.matthies@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
changeset 768e6dadd74 caused a regression on using mb86a20s
in parallel mode, as the parallel mode selection got
overriden by mb86a20s_init2.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
According with Manu Abraham, stb0899 seek algorithm is broken
for symbol rates bellow to 5Mbauds. So, revert those patches:
55b3318 [media] stb0899: allow minimum symbol rate of 2000000
2eeed77 [media] stb0899: allow minimum symbol rate of 1000000
Requested-by: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is no longer needed since the core now handles this through DBG_G_CHIP_INFO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
There are a few cases where breaking the code into separate
lines make it worse to read. However, on several places,
breaking it to make checkpatch.pl happier is OK and improves
code readability.
So, break longer lines where that won't cause harm.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
There are several places where: state->var = (some_var)
The parenthesis there are doing nothing but making it
harder to read and breaking the 80 columns soft limits.
Just get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
