IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The tx_status is most likely going to be asked for the current transfer, so
check that first then try to fall back to lookup of non started transfers.
In this way the code is a bit more readable and in most cases we will avoid
to run vchan_find_desc() all the time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190716082459.1222-2-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current driver works perfectly fine on every generation of the
JZ47xx SoCs, except on the JZ4740.
There, when hardware descriptors are chained together (with the LINK
bit set), the next descriptor isn't automatically fetched as it should -
instead, an interrupt is raised, even if the TIE bit (Transfer Interrupt
Enable) bit is cleared. When it happens, the DMA transfer seems to be
stopped (it doesn't chain), and it's uncertain how many bytes have
actually been transferred.
Until somebody smarter than me can figure out how to make chained
descriptors work on the JZ4740, we now disable chained descriptors on
that particular SoC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20190714215504.10877-1-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
During enabling of the RPi 4, we found out that the driver doesn't provide
a helpful error message in case setting DMA mask fails. So add one.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/1563297318-4900-1-git-send-email-wahrenst@gmx.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With the audio driver no longer referring to this function, it
can be made private to the dmaengine driver itself, and the
header file removed.
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190722081705.2084961-2-arnd@arndb.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Add support in dmaengine core to do device node checks for DT devices and
update bunch of drivers to use that and remove open coding from drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
-----BEGIN PGP SIGNATURE-----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=R+aC
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Add support in dmaengine core to do device node checks for DT devices
and update bunch of drivers to use that and remove open coding from
drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
* tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: Revert "dmaengine: fsl-edma: add i.mx7ulp edma2 version support"
dmaengine: at_xdmac: check for non-empty xfers_list before invoking callback
Documentation: dmaengine: clean up description of dmatest usage
dmaengine: tegra210-adma: remove PM_CLK dependency
dmaengine: fsl-edma: add i.mx7ulp edma2 version support
dt-bindings: dma: fsl-edma: add new i.mx7ulp-edma
dmaengine: fsl-edma-common: version check for v2 instead
dmaengine: fsl-edma-common: move dmamux register to another single function
dmaengine: fsl-edma: add drvdata for fsl-edma
dmaengine: Revert "dmaengine: fsl-edma: support little endian for edma driver"
dmaengine: rcar-dmac: Reject zero-length slave DMA requests
dmaengine: dw: Enable iDMA 32-bit on Intel Elkhart Lake
dmaengine: dw-edma: fix semicolon.cocci warnings
dmaengine: sh: usb-dmac: Use [] to denote a flexible array member
dmaengine: dmatest: timeout value of -1 should specify infinite wait
dmaengine: dw: Distinguish ->remove() between DW and iDMA 32-bit
dmaengine: fsl-edma: support little endian for edma driver
dmaengine: hsu: Revert "set HSU_CH_MTSR to memory width"
dmagengine: pl330: add code to get reset property
dt-bindings: pl330: document the optional resets property
...
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
* fix BCH ECC layout for large page NAND parts
* fallback to detected ecc-strength, ecc-step-size
* when oops in progress use pio and interrupt polling
* code refactor code to introduce helper functions
* add support for v7.3 controller
- FSMC:
* use nand_op_trace for operation tracing
- GPMI:
* move all driver code into single file
* various cleanups (including dmaengine changes)
* use runtime PM to manage clocks
* implement exec_op
- MTK:
* correct low level time calculation of r/w cycle
* improve data sampling timing for read cycle
* add validity check for CE# pin setting
* fix wrongly assigned OOB buffer pointer issue
* re-license MTK NAND driver as Dual MIT/GPL
- STM32:
* manage the get_irq error case
* increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0qLr4ACgkQJWrqGEe9
VoQVCwf/ZCG5CldS3cs6B68kMJoZ/rJyJxBnxtIhffda2vw1KG/12o6XaDO9xA/R
EwYrOTzlYZxzCZsNvWyHepG3Kj3d38CJ52ZqhavjpihwMlKKOgW/K39xuKWCrfxS
sVMLz/UdrcsQfcPGAy7DSyqhzRAtupNxngCdEkIIMGFZWsv4uZfOFEGMrzUJ5RYN
/okIyUE7Iz0dRq1/KXSl365V1MS8QP2eHFuHrUd38+kJ8TJnQjXX3Bmdul4aNTx+
HIIpykovoAn5BZ0YA4lJL90zVoDOWysARwHIAMDvJa8zS0wDTU16Tj2M6AQK+a4x
hbIOOkeX0hTKpJvy7/khli5y1bn2mw==
=L+tV
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"This contains the following changes for MTD:
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
- fix BCH ECC layout for large page NAND parts
- fallback to detected ecc-strength, ecc-step-size
- when oops in progress use pio and interrupt polling
- code refactor code to introduce helper functions
- add support for v7.3 controller
- FSMC:
- use nand_op_trace for operation tracing
- GPMI:
- move all driver code into single file
- various cleanups (including dmaengine changes)
- use runtime PM to manage clocks
- implement exec_op
- MTK:
- correct low level time calculation of r/w cycle
- improve data sampling timing for read cycle
- add validity check for CE# pin setting
- fix wrongly assigned OOB buffer pointer issue
- re-license MTK NAND driver as Dual MIT/GPL
- STM32:
- manage the get_irq error case
- increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control"
* tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (60 commits)
mtd: concat: implement _is_locked mtd operation
mtd: concat: refactor concat_lock/concat_unlock
mtd: abi: do not use C++ style comments in uapi header
mtd: afs: remove unneeded NULL check
mtd: rawnand: stm32_fmc2: increase DMA completion timeouts
mtd: rawnand: Use kzalloc() instead of kmalloc() and memset()
mtd: hyperbus: Add driver for TI's HyperBus memory controller
mtd: spinand: read returns badly if the last page has bitflips
mtd: spinand: Add initial support for Paragon PN26G0xA
mtd: rawnand: mtk: Re-license MTK NAND driver as Dual MIT/GPL
mtd: rawnand: gpmi: remove double assignment to block_size
dt-bindings: mtd: brcmnand: Add brcmnand, brcmnand-v7.3 support
mtd: rawnand: brcmnand: Add support for v7.3 controller
mtd: rawnand: brcmnand: Refactored code to introduce helper functions
mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling
mtd: Add flag to indicate panic_write
mtd: rawnand: Add Macronix NAND read retry support
mtd: onenand: Avoid fall-through warnings
mtd: spinand: Add support for GigaDevice GD5F1GQ4UFxxG
mtd: spinand: Add support for two-byte device IDs
...
This reverts commit 7144afd025 ("dmaengine: fsl-edma: add i.mx7ulp
edma2 version support") as this fails to build with module option due to
usage of of_irq_count() which is not an exported symbol as kernel
drivers are *not* expected to use it (rightly so).
Signed-off-by: Vinod Koul <vkoul@kernel.org>
tx descriptor retrieved from an empty xfers_list may not have valid
pointers to the callback functions.
Avoid calling dmaengine_desc_get_callback_invoke if xfers_list is empty.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
One space is left unused in circular FIFO to differentiate
'full' and 'empty' cases. So take that in to account while
counting for the descriptors completed.
Fixes the issue reported here,
https://lkml.org/lkml/2019/6/18/669
Cc: stable@vger.kernel.org
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It is possible for an irq triggered by channel0 to be received later
after clks are disabled once firmware loaded during sdma probe. If
that happens then clearing them by writing to SDMA_H_INTR won't work
and the kernel will hang processing infinite interrupts. Actually,
don't need interrupt triggered on channel0 since it's pollling
SDMA_H_STATSTOP to know channel0 done rather than interrupt in
current code, just clear BD_INTR to disable channel0 interrupt to
avoid the above case.
This issue was brought by commit 1d069bfa3c ("dmaengine: imx-sdma:
ack channel 0 IRQ in the interrupt handler") which didn't take care
the above case.
Fixes: 1d069bfa3c ("dmaengine: imx-sdma: ack channel 0 IRQ in the interrupt handler")
Cc: stable@vger.kernel.org #5.0+
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reported-by: Sven Van Asbroeck <thesven73@gmail.com>
Tested-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If probe() fails anywhere beyond the point where
sdma_get_firmware() is called, then a kernel oops may occur.
Problematic sequence of events:
1. probe() calls sdma_get_firmware(), which schedules the
firmware callback to run when firmware becomes available,
using the sdma instance structure as the context
2. probe() encounters an error, which deallocates the
sdma instance structure
3. firmware becomes available, firmware callback is
called with deallocated sdma instance structure
4. use after free - kernel oops !
Solution: only attempt to load firmware when we're certain
that probe() will succeed. This guarantees that the firmware
callback's context will remain valid.
Note that the remove() path is unaffected by this issue: the
firmware loader will increment the driver module's use count,
ensuring that the module cannot be unloaded while the
firmware callback is pending or running.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
[vkoul: fixed braces for if condition]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The "pending" variable was a u32 but we cast it to an unsigned long
pointer when we do the for_each_set_bit() loop. The problem is that on
big endian 64bit systems that results in an out of bounds read.
Fixes: 4e4106f5e9 ("dmaengine: jz4780: Fix transfers being ACKed too soon")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tegra ADMA does not use pm-clk interface now and hence the dependency
is removed from Kconfig.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add edma2 for i.mx7ulp by version v3, since v2 has already
been used by mcf-edma.
The big changes based on v1 are belows:
1. only one dmamux.
2. another clock dma_clk except dmamux clk.
3. 16 independent interrupts instead of only one interrupt for
all channels.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The next v3 i.mx7ulp edma is based on v1, so change version
check logic for v2 instead.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Prepare for edmav2 on i.mx7ulp whose dmamux register is 32bit. No function
impacted.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are some differences between vf610 and next i.mx7ulp. Put such
differences into static driver data for distinguishing easily at
driver level. Change mcf-edma accordingly.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This reverts commit 002905eca5.
Commit 002905eca5 ("dmaengine: fsl-edma: support little endian for edma
driver") incorrectly assumed that there was not little endian support
in the driver.
This causes hangs on Vybrid, so revert it so that Vybrid systems
could boot again.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The gpmi driver performance suffers from NAND operations being split
in multiple small DMA transfers. This has been forced by the NAND layer
in the former days, but now with exec_op we can use the controller as
intended.
With this patch gpmi_nfc_exec_op becomes the main entry point to NAND
operations. Here all instructions are collected and chained as separate
DMA transfers. In the end whole chain is fired and waited to be
finished. gpmi_nfc_exec_op only does the hardware operations, bad block
marker swapping and buffer scrambling is done by the callers. It's worth
noting that the nand_*_op functions always take the buffer lengths for
the data that the NAND chip actually transfers. When doing BCH we have
to calculate the net data size from the raw data size in some places.
This patch has been tested with 2048/64 and 2048/128 byte NAND on
i.MX6q. mtd_oobtest, mtd_subpagetest and mtd_speedtest run without
errors. nandbiterrs, nandpagetest and nandsubpagetest userspace tests
from mtdutils run without errors and UBIFS can successfully be mounted.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The mxs dma driver uses the flags parameter in dmaengine_prep_slave_sg() for
custom flags, but still uses the dmaengine specific names of the flags.
Do a little bit better and at least give the flag a custom name.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The mxs dma driver can do PIO transfers. A pointer to the PIO words
to transfer is passed in the struct scatterlist * argument of
dmaengine_prep_slave_sg(). It's quite ugly and non obvious to cast
u32 * to struct scatterlist * each time when calling
dmaengine_prep_slave_sg(), so add a static inline wrapper function
to be called by the user along with a description what is going on.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The mxs dma driver insists on having the DMA_PREP_INTERRUPT flag set
on all but the first transfer. There's no need to let the user set this
flag, the driver can do it internally whenever it needs it. Drop
handling of this flag from the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
While the .device_prep_slave_sg() callback rejects empty scatterlists,
it still accepts single-entry scatterlists with a zero-length segment.
These may happen if a driver calls dmaengine_prep_slave_single() with a
zero len parameter. The corresponding DMA request will never complete,
leading to messages like:
rcar-dmac e7300000.dma-controller: Channel Address Error happen
and DMA timeouts.
Although requesting a zero-length DMA request is a driver bug, rejecting
it early eases debugging. Note that the .device_prep_dma_memcpy()
callback already rejects requests to copy zero bytes.
Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Analyzed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel Elkhart Lake OSE (Offload Service Engine) provides few DMA controllers
to the host. Enable them in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Flexible array members should be denoted using [] instead of [0], else
gcc will not warn when they are no longer at the end of the structure.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The dmatest module parameter 'timeout' is documented as accepting a
-1 to mean "infinite timeout". However, an infinite timeout is not
advised, nor possible since the module parameter is an unsigned int,
which won't accept a negative value. Change the parameter
comment to reflect current behavior, which allows values from 0 up to
4294967295 (0xFFFFFFFF).
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the same way as done for ->probe(), call ->remove() based on
the type of the hardware.
While it works now due to equivalency of the two removal functions,
it might be changed in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The commit
080edf75d3 ("dmaengine: hsu: set HSU_CH_MTSR to memory width")
has been mistakenly submitted. The further investigations show that
the original code does better job since the memory side transfer size
has never been configured by DMA users.
As per latest revision of documentation: "Channel minimum transfer size
(CHnMTSR)... For IOSF UART, maximum value that can be programmed is 64 and
minimum value that can be programmed is 1."
This reverts commit 080edf75d3.
Fixes: 080edf75d3 ("dmaengine: hsu: set HSU_CH_MTSR to memory width")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA controller on some SoCs can be held in reset, and thus requires
the reset signal(s) to deasserted. Most SoCs will have just one reset
signal, but there are others, i.e. Arria10/Stratix10 will have an
additional reset signal, referred to as the OCP.
Add code to get the reset property from the device tree for deassert and
assert.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The registers for AXI DMAC are detailed at:
https://wiki.analog.com/resources/fpga/docs/axi_dmac#register_map
This change adds regmap support for these registers, in case some wants to
have a more direct access to them via this interface.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
[vkoul: fixed code style issue]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When a partial transfer is received, the driver should not submit any more
segments to the hardware, as they will be ignored/unused until a new
transfer start operation is done.
This change implements this by adding a new flag on the AXI DMAC
descriptor. This flags is set to true, if there was a partial transfer in
a previously completed segment. When that flag is true, the TLAST flag is
added to the to the submitted segment, signaling the controller to stop
receiving more segments.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Starting with version 4.2.a, the AXI DMAC controller can report partial
transfers that have been issued.
This change implements computing DMA residue information for transfers,
based on that reported information.
The way this is done, is to dequeue the partial transfers from the FIFO of
partial transfers, store the partial length to the correct segment &
descriptor, and compute the residue before submitting the DMA cookie to the
DMA framework.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This allows each virtual channel to store information about each transfer
that completed, i.e. which transfer succeeded (or which failed) and if
there was any residue data on each (completed) transfer.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Also, because there is no need to save the file dentry, remove the
variables that were saving them as they were never even being used once
set.
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Also, because there is no need to save the file dentry, remove the
variable that was saving it as it was never even being used once set.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No need to check the return value of debugfs_create_file(), so no need
to provide a fake "cast away" of the return value either.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Also, because there is no need to save the file dentry, remove the
variable that was saving it as it was never even being used once set.
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No need to check the return value of debugfs_create_file(), so no need
to provide a fake "cast away" of the return value either.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If CONFIG_PCI_MSI is not set, building with CONFIG_DW_EDMA
fails:
drivers/dma/dw-edma/dw-edma-core.c: In function dw_edma_irq_request:
drivers/dma/dw-edma/dw-edma-core.c:784:21: error: implicit declaration of function pci_irq_vector; did you mean rcu_irq_enter? [-Werror=implicit-function-declaration]
err = request_irq(pci_irq_vector(to_pci_dev(dev), 0),
^~~~~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e63d79d1ff ("dmaengine: Add Synopsys eDMA IP core driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The change replaces the old license information in the comment header with
the new SPDX license specifier.
As well as bumping the year range from 2013-2015 to 2013-2019.
The latter also reflects recent changes that were added to the driver.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Synopsys eDMA IP is normally distributed along with Synopsys PCIe
EndPoint IP (depends of the use and licensing agreement).
This IP requires some basic configurations, such as:
- eDMA registers BAR
- eDMA registers offset
- eDMA registers size
- eDMA linked list memory BAR
- eDMA linked list memory offset
- eDMA linked list memory size
- eDMA data memory BAR
- eDMA data memory offset
- eDMA data memory size
- eDMA version
- eDMA mode
- IRQs available for eDMA
As a working example, PCIe glue-logic will attach to a Synopsys PCIe
EndPoint IP prototype kit (Vendor ID = 0x16c3, Device ID = 0xedda),
which has built-in an eDMA IP with this default configuration:
- eDMA registers BAR = 0
- eDMA registers offset = 0x00001000 (4 Kbytes)
- eDMA registers size = 0x00002000 (8 Kbytes)
- eDMA linked list memory BAR = 2
- eDMA linked list memory offset = 0x00000000 (0 Kbytes)
- eDMA linked list memory size = 0x00800000 (8 Mbytes)
- eDMA data memory BAR = 2
- eDMA data memory offset = 0x00800000 (8 Mbytes)
- eDMA data memory size = 0x03800000 (56 Mbytes)
- eDMA version = 0
- eDMA mode = EDMA_MODE_UNROLL
- IRQs = 1
This driver can be compile as built-in or external module in kernel.
To enable this driver just select DW_EDMA_PCIE option in kernel
configuration, however it requires and selects automatically DW_EDMA
option too.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
