IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Add common LED properties - the function and color - to aat1290 flash
LED node in Galaxy S3, so we can drop deprecated label property.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220620175033.130468-4-krzysztof.kozlowski@linaro.org
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Meraki MR26 is an EOL wireless access point featuring a
PoE ethernet port and two dual-band 3x3 MIMO 802.11n
radios and 1x1 dual-band WIFI dedicated to scanning.
Thank you Amir for the unit and PSU.
Hardware info:
SOC : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz)
RAM : SK Hynix Inc. H5TQ1G63EFR, 1 GBit DDR3 SDRAM = 128 MiB
NAND : Spansion S34ML01G100TF100, 1 GBit SLC NAND Flash = 128 MiB
ETH : 1 GBit Ethernet Port - PoE (TPS23754 PoE Interface)
WIFI0 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI2 : Broadcom BCM43428 "Air Marshal" 802.11 abgn (1x1:1)
BUTTON: One reset key behind a small hole next to the Ethernet Port
LEDS : One amber (fault), one white (indicator) LED, separate RGB-LED
MISC : Atmel AT24C64 8KiB EEPROM i2c
: Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor
SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC (next to J3, has the pin 1 indicator), RX, TX, GND.
Odd stuff:
- uboot does not support lzma compression, but gzip'd uImage/DTB work.
- uboot claims to support FIT, but fails to pass the DTB to the kernel.
Appending the dtb after the kernel image works.
- RGB-controller is supported through an external userspace program.
- The ubi partition contains a "board-config" volume. It stores the
MAC Address (0x66 in binary) and Serial No. (0x7c alpha-numerical).
- SoC's temperature sensor always reports that it is on fire.
This causes the system to immediately shutdown! Looking at reported
"418 degree Celsius" suggests that this sensor is not working.
WIFI:
b43 is able to initialize all three WIFIs @ 802.11bg.
| b43-phy0: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0000:01:00.0: bus1: Switched to core: 0x812
| b43-phy0: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy0: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy0 warning: 5 GHz band is unsupported on this PHY
| b43-phy1: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0001:01:00.0: bus2: Switched to core: 0x812
| b43-phy1: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy1: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy1 warning: 5 GHz band is unsupported on this PHY
| b43-phy2: Broadcom 43228 WLAN found (core revision 30)
| bcma-pci-bridge 0002:01:00.0: bus3: Switched to core: 0x812
| b43-phy2: Found PHY: Analog 9, Type 4 (N), Revision 16
| b43-phy2: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
| Broadcom 43xx driver loaded [ Features: NL ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
- Sort nodes and properties alphabetical
- End all pinctrl node names in grp and avoid using dashes
- Change the pmic's node name to pmic@8 per binding requirement
- Add sound-dai-cells to the codec node per binding requirement
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adapt the brightness steps as the backlight doesn't light up
for very low duty cycles.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set #pwm-cells to the default 3 to gain access to the parameter
which allows inverting the PWM signal. This is useful to specify
a backlight which has its highest brightness at 0.
With the change to use the PWM with inverted polarity the PWM signal
is inverted to how it was before this patch.
This changes the meaning of the values in the brightness-levels
property. I.e. the duty-cycle changes from x/255 to (255-x)/255.
Keeping the brightness-levels will then have a big brightness
jump from 0 to 127 duty cycle, the other 6 steps will then be
barely noticeable.
Change the brightness-levels to provide the same brightness-levels
as before.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Ixora V1.2 carrier board adds SW relevant new features compared to
the V1.1 version.
- An I2C EEPROM is added.
- The SD card slot got a switchable 3.3V supply.
- Pull ups on the SD card signals are not assembled to faciliate 1.8V
speed modes.
- The CAN transceivers got a switchable 3.3V supply.
Add a new device tree and, as the differences are so small rework the
device tree for V1.1 to include the V1.2 device tree and adjust as
needed.
Drop adding the toradex,apalis_imx6q-ixora to the dtb compatible to
adhere to the binding yaml document.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Configure SOM DTSI to 8-bit, card detect in the SoM dtsi as this is
the Apalis family default functionality.
Limit the interface to 4-bit only on the Ixora V1.1 carrier boards.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Apalis iMX6 modules allow connecting a parallel video input.
Add support for our ADV7280 video input module but have it disabled.
This allows to enable it in an overlay per the current system
configuration.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Apalis iMX6 modules allow connecting a mipi-csi video input.
Add support for our OV5640 camera module but have it disabled.
This allows to enable it in an overlay per the current system
configuration.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Unify its label with other toradex SoM dtbs.
This allows to enable it in an overlay per the current
system configuration.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This allows to enable it in an overlay per the current system
configuration.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add LVDS panel and endpoint linkage support but keep the inherited
disabled state. This allows to enable it in an overlay per the current
system configuration.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move gpio-keys to module-level device tree given it is standard Apalis
functionality.
Sort properties alphabetical.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reduces code duplication. While at it drop the comments which do not
apply on Apalis iMX6 but add the correct SoM pin names.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPIO pinmux groups are declared on the module level. Move muxing
them to the same level. It also reduces code duplication.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move all Parallel RGB-related nodes to the module level and disable it by
default. This allows to enable it in an overlay per the current system
configuration.
Update SPDX-License spelling to latest convention.
Update Copyright year.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Apalis iMX6 HW doesn't allow to use the PWR_ON_REQ signal for
poweroff. Use the fsl,pmic-stby-poweroff property to command the PMIC
into a low power mode in poweroff.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add GPIO line names on module level. Those are all GPIOs which a user
might use on his custom carrier board. If more meaningful names are
available on the carrier board, the user can overwrite the line names
in the carrier board level device tree.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The STMPE MFD device binding requires the child node to have a fixed
name, i.e. with '_', not '-'. Otherwise the stmpe_adc, stmpe_touchscreen
drivers will not be probed.
Fixes: 56086b5e804f ("ARM: dts: imx6qdl-apalis: Avoid underscore in node name")
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass a label to the AIPS nodes to make it easier to reference
it from other devicetree files.
Some i.MX dtsi files already describe labels for the AIPS nodes.
Make it available for all SoCs for consistency.
U-Boot, for example usually needs to access the AIPS node to
pass U-Boot-specific properties.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass a label to the 'soc' node to make it easier to reference
it from other devicetree files.
U-Boot, for example usually needs to access the AIPS node to
pass U-Boot-specific properties.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6ul is not compatible to imx6sx, both have different erratas.
Fixes the dt_binding_check warning:
spi@21e0000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-qspi', 'fsl,imx6sx-qspi'] is too long
Additional items are not allowed ('fsl,imx6sx-qspi' was unexpected)
'fsl,imx6ul-qspi' is not one of ['fsl,ls1043a-qspi']
'fsl,imx6ul-qspi' is not one of ['fsl,imx8mq-qspi']
'fsl,ls1021a-qspi' was expected
'fsl,imx7d-qspi' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In yaml binding "fsl,imx6ul-lcdif" is listed as compatible to imx6sx-lcdif,
but not imx28-lcdif. Change the list accordingly. Fixes the
dt_binding_check warning:
lcdif@21c8000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-lcdif', 'fsl,imx28-lcdif'] is too long
Additional items are not allowed ('fsl,imx28-lcdif' was unexpected)
'fsl,imx6ul-lcdif' is not one of ['fsl,imx23-lcdif', 'fsl,imx28-lcdif',
'fsl,imx6sx-lcdif']
'fsl,imx6sx-lcdif' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"fsl,imx6ul-csi" was never listed as compatible to "fsl,imx7-csi", neither
in yaml bindings, nor previous txt binding. Remove the imx7 part. Fixes
the dt schema check warning:
csi@21c4000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-csi', 'fsl,imx7-csi'] is too long
Additional items are not allowed ('fsl,imx7-csi' was unexpected)
'fsl,imx8mm-csi' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to binding, the compatible shall only contain imx6ul and imx21
compatibles. Fixes the dt_binding_check warning:
keypad@20b8000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-kpp', 'fsl,imx6q-kpp', 'fsl,imx21-kpp'] is too long
Additional items are not allowed ('fsl,imx6q-kpp', 'fsl,imx21-kpp' were
unexpected)
Additional items are not allowed ('fsl,imx21-kpp' was unexpected)
'fsl,imx21-kpp' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
operating-points is a uint32-matrix as per opp-v1.yaml. Change it
accordingly. While at it, change fsl,soc-operating-points as well,
although there is no bindings file (yet). But they should have the same
format. Fixes the dt_binding_check warning:
cpu@0: operating-points:0: [696000, 1275000, 528000, 1175000, 396000,
1025000, 198000, 950000] is too long
cpu@0: operating-points:0: Additional items are not allowed (528000,
1175000, 396000, 1025000, 198000, 950000 were unexpected)
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All 3 properties are required by sram.yaml. Fixes the dtbs_check
warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
usdhc2 is connected to a Wifi chip that is powered by a 3.3V supply.
Pass the "no-1-8-v" property to guarantee that no communication is
made at 1.8V.
While at it, also remove the unnecessary properties: "cap-sd-highspeed",
"sd-uhs-ddr50", and "mmc-ddr-1_8v".
Fixes: 9ac0ae97e349 ("ARM: dts: imx7d-smegw01: Add support for i.MX7D SMEGW01 board")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Skov's i.MX6 based boards come in different flavors which have different panels
attached. For optimal contrast experience each panel type needs an individual
common voltage (VCOM) to drive its TFT backplane. The latter is generated by an
LCD bias supply IC controlled by a pwm as input signal. Introduce a pwm-
regulator to describe this hardware property and parameterize it appropriately
for the different boards.
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix whitespace coding style: use single space instead of tabs or
multiple spaces around '=' sign in property assignment. No functional
changes (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20220526204139.831895-3-krzysztof.kozlowski@linaro.org
The GPIO expander line names has been fixed in the vendor tree last year,
so upstream these changes.
Fixes: 1c701accecf2 ("ARM: dts: Add Raspberry Pi 400 support")
Reported-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
