IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The kernel entry points of both boot CPU (i.e., kernel_entry) and non-
boot CPUs (i.e., smpboot_entry) may be physical address from BootLoader
(in DA mode or identity-mapping PG mode). So we should jump to the link
address before PG enabled (because DA is disabled at the same time) and
just after DMW configured.
Specifically: With some older firmwares, non-boot CPUs started with PG
enabled, but this need firmware cooperation in the form of a temporary
page table, which is deemed unnecessary. OTOH, latest firmware versions
configure the non-boot CPUs to start in DA mode, so kernel-side changes
are needed.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
The return value from the call to get_timer_irq() is int, which can be
a negative error code. However, the return value is being assigned to an
unsigned int variable 'irq', so making 'irq' an int.
Eliminate the following coccicheck warning:
./arch/loongarch/kernel/time.c:146:5-8: WARNING: Unsigned expression compared with zero: irq < 0
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
1, ACPI, EFI and SMP are mandatories for LoongArch, select them
unconditionally to avoid various build errors for 'make randconfig'.
2, Move the MMU_GATHER_MERGE_VMAS selection to the correct place.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
We can see the "ROM Size" is different in the following outputs:
[root@linux loongson]# cat /sys/firmware/loongson/boardinfo
BIOS Information
Vendor : Loongson
Version : vUDK2018-LoongArch-V2.0.pre-beta8
ROM Size : 63 KB
Release Date : 06/15/2022
Board Information
Manufacturer : Loongson
Board Name : Loongson-LS3A5000-7A1000-1w-A2101
Family : LOONGSON64
[root@linux loongson]# dmidecode | head -11
...
Handle 0x0000, DMI type 0, 26 bytes
BIOS Information
Vendor: Loongson
Version: vUDK2018-LoongArch-V2.0.pre-beta8
Release Date: 06/15/2022
ROM Size: 4 MB
According to "BIOS Information (Type 0) structure" in the SMBIOS
Reference Specification [1], it shows 64K * (n+1) is the size of
the physical device containing the BIOS if the size is less than
16M.
Additionally, we can see the related code in dmidecode [2]:
u64 s = { .l = (code1 + 1) << 6 };
So the output of dmidecode is correct, the output of boardinfo
is wrong, fix it.
By the way, at present no need to consider the size is 16M or
greater on LoongArch, because it is usually 4M or 8M which is
enough to use.
[1] https://www.dmtf.org/sites/default/files/standards/documents/DSP0134_3.6.0.pdf
[2] https://git.savannah.nongnu.org/cgit/dmidecode.git/tree/dmidecode.c#n347
Fixes: 628c3bb40e9a ("LoongArch: Add boot and setup routines")
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
In file ptrace.c, function fpr_set does not copy fcsr data from ubuf
to kbuf. That's the reason why fcsr cannot be modified by ptrace.
This patch fixs this problem and allows users using ptrace to modify
the fcsr.
Co-developed-by: Xu Li <lixu@loongson.cn>
Signed-off-by: Qi Hu <huqi@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Current calculation of shared cache size is from the node (die) scope,
but we hope 'lscpu' to show the shared cache size of the whole package
for multi-die chips (e.g., Loongson-3C5000L, which contains 4 dies in
one package). So fix it by multiplying nodes_per_package.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Disable executable stack for LoongArch by default, as all modern
architectures do.
Reported-by: Andreas Schwab <schwab@suse.de>
Suggested-by: WANG Xuerui <git@xen0n.name>
Link: https://sourceware.org/pipermail/binutils/2022-July/121992.html
Tested-by: WANG Xuerui <git@xen0n.name>
Tested-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
There are some variables never used or referenced, this patch
removes these varaibles and make the code cleaner.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
On physical machine we can save power by disabling clock of hot removed
cpu. However as different platforms require different methods to
configure clocks, the code is platform-specific, and probably belongs to
firmware/pmu or cpu regulator, rather than generic arch/loongarch code.
Also, there is no such register on QEMU virt machine since the
clock/frequency regulation is not emulated.
This patch removes the hard-coded clock register accesses in generic
LoongArch cpu hotplug flow.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
The content of LoongArch's compiler.h is trivial, with some unused
anywhere, so inline the definitions and remove the header.
Signed-off-by: Jun Yi <yijun@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
These syntactic sugars have been supported by upstream binutils from the
beginning, so no need to patch them locally.
Signed-off-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Reflow the *.S files for better stylistic consistency, namely hard tabs
after mnemonic position, and vertical alignment of the first operand
with hard tabs. Tab width is obviously 8. Some pre-existing intra-block
vertical alignments are preserved.
Signed-off-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Support for the syntactic sugar is present in upstream binutils port
from the beginning. Use it for shorter lines and better consistency.
Generated code should be identical.
Signed-off-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Support for the syntactic sugar is present in upstream binutils port
from the beginning. Use it for shorter lines and better consistency.
Generated code should be identical.
Signed-off-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
While B{EQ,NE}Z and B{EQ,NE} are different instructions, and the vastly
expanded range for branch destination does not really matter in the few
cases touched, use the B{EQ,NE}Z where possible for shorter lines and
better consistency (e.g. some places used "BEQ foo, zero", while some
used "BEQ zero, foo").
Signed-off-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Some of the assembly code in the LoongArch port likely originated
from a time when the assembler did not support pseudo-instructions like
"move" or "jr", so the desugared form was used and readability suffers
(to a minor degree) as a result.
As the upstream toolchain supports these pseudo-instructions from the
beginning, migrate the existing few usages to them for better
readability.
Signed-off-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Some of the assembly code in the LoongArch port likely originated
from a time when the assembler did not support pseudo-instructions like
"move" or "jr", so the desugared form was used and readability suffers
(to a minor degree) as a result.
As the upstream toolchain supports these pseudo-instructions from the
beginning, migrate the existing few usages to them for better
readability.
Signed-off-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Some of the assembly in the LoongArch port seem to come from a
prehistoric time, when the assembler didn't even have support for the
ABI names we all come to know and love, thus used raw register numbers
which hampered readability.
The usages are found with a regex match inside arch/loongarch, then
manually adjusted for those non-definitions.
Signed-off-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Scattered across the archs are 3 basic forms of tlb_{start,end}_vma().
Provide two new MMU_GATHER_knobs to enumerate them and remove the per
arch tlb_{start,end}_vma() implementations.
- MMU_GATHER_NO_FLUSH_CACHE indicates the arch has flush_cache_range()
but does *NOT* want to call it for each VMA.
- MMU_GATHER_MERGE_VMAS indicates the arch wants to merge the
invalidate across multiple VMAs if possible.
With these it is possible to capture the three forms:
1) empty stubs;
select MMU_GATHER_NO_FLUSH_CACHE and MMU_GATHER_MERGE_VMAS
2) start: flush_cache_range(), end: empty;
select MMU_GATHER_MERGE_VMAS
3) start: flush_cache_range(), end: flush_tlb_range();
default
Obviously, if the architecture does not have flush_cache_range() then
it also doesn't need to select MMU_GATHER_NO_FLUSH_CACHE.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LoongArch CPUINTC stands for CSR.ECFG/CSR.ESTAT and related interrupt
controller that described in Section 7.4 of "LoongArch Reference Manual,
Vol 1". For more information please refer Documentation/loongarch/irq-
chip-model.rst.
LoongArch CPUINTC has 13 interrupt sources: SWI0~1, HWI0~7, IPI, TI
(Timer) and PCOV (PMC). IRQ mappings of HWI0~7 are configurable (can be
created from DT/ACPI), but IPI, TI (Timer) and PCOV (PMC) are hardcoded
bits, so we expose the fwnode_handle to map them, and get mapped irq
by irq_create_mapping when using them.
Co-developed-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1658314292-35346-13-git-send-email-lvjianmin@loongson.cn
EIOINTC stands for "Extended I/O Interrupts" that described in Section
11.2 of "Loongson 3A5000 Processor Reference Manual". For more
information please refer Documentation/loongarch/irq-chip-model.rst.
Loongson-3A5000 has 4 cores per NUMA node, and each NUMA node has an
EIOINTC; while Loongson-3C5000 has 16 cores per NUMA node, and each NUMA
node has 4 EIOINTCs. In other words, 16 cores of one NUMA node in
Loongson-3C5000 are organized in 4 groups, each group connects to an
EIOINTC. We call the "group" here as an EIOINTC node, so each EIOINTC
node always includes 4 cores (both in Loongson-3A5000 and Loongson-
3C5000).
Co-developed-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1658314292-35346-12-git-send-email-lvjianmin@loongson.cn
LIOINTC stands for "Legacy I/O Interrupts" that described in Section
11.1 of "Loongson 3A5000 Processor Reference Manual". For more
information please refer Documentation/loongarch/irq-chip-model.rst.
Co-developed-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1658314292-35346-11-git-send-email-lvjianmin@loongson.cn
PCH-PIC/PCH-MSI stands for "Interrupt Controller" that described in
Section 5 of "Loongson 7A1000 Bridge User Manual". For more information
please refer Documentation/loongarch/irq-chip-model.rst.
Co-developed-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1658314292-35346-10-git-send-email-lvjianmin@loongson.cn
PCH-PIC/PCH-MSI stands for "Interrupt Controller" that described in
Section 5 of "Loongson 7A1000 Bridge User Manual". For more information
please refer Documentation/loongarch/irq-chip-model.rst.
Co-developed-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1658314292-35346-9-git-send-email-lvjianmin@loongson.cn
PCH-LPC stands for "LPC Interrupts" that described in Section 24.3 of
"Loongson 7A1000 Bridge User Manual". For more information please refer
Documentation/loongarch/irq-chip-model.rst.
Co-developed-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1658314292-35346-8-git-send-email-lvjianmin@loongson.cn
For systems with two chipsets, there are two related pch-pic and
pch-msi irqdomains, each of which has the same node id as its
parent irqdomain. So we use a structure to mantain the relation
of node and it's parent irqdomain as pch irqdomin, the 'pci_segment'
field is only used to match the pci segment of a pci device when
setting msi irqdomain for the device.
struct acpi_vector_group {
int node;
int pci_segment;
struct irq_domain *parent;
};
The field 'pci_segment' and 'node' are initialized from MCFG, and
the parent irqdomain driver will set field 'parent' by matching same
'node'.
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1658314292-35346-7-git-send-email-lvjianmin@loongson.cn
For LoongArch, generic gsi code(driver/acpi/irq.c) can be
reused after following patchs:
APCI: irq: Add support for multiple GSI domains
ACPI: irq: Allow acpi_gsi_to_irq() to have an arch-specific fallback
So, config ACPI_GENERIC_GSI for LoongArch with removing the gsi code
in arch directory.
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1658314292-35346-6-git-send-email-lvjianmin@loongson.cn
The LoongArch architecture is using ACPI, but the spec containing
the required updates still is in an unreleased state.
Instead of preventing the inclusion of the IRQ support into the
kernel, add the missing bits to the arch-specific parts of
the ACPICA support.
Once the ACPICA bits are updated to the version that supports
LoongArch, these bits can eventually be removed.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Link: https://lore.kernel.org/r/1658314292-35346-2-git-send-email-lvjianmin@loongson.cn
init_numa_memory() is annotated __init and not used by any module,
thus don't export it.
Remove not needed EXPORT_SYMBOL for init_numa_memory() to fix the
following section mismatch warning:
MODPOST vmlinux.symvers
WARNING: modpost: vmlinux.o(___ksymtab+init_numa_memory+0x0): Section mismatch in reference
from the variable __ksymtab_init_numa_memory to the function .init.text:init_numa_memory()
The symbol init_numa_memory is exported and annotated __init
Fix this by removing the __init annotation of init_numa_memory or drop the export.
This is build on Linux 5.19-rc4.
Fixes: d4b6f1562a3c ("LoongArch: Add Non-Uniform Memory Access (NUMA) support")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Building loongarch:tinyconfig fails with the following error.
./arch/loongarch/include/asm/page.h: In function 'pfn_valid':
./arch/loongarch/include/asm/page.h:42:32: error: 'PHYS_OFFSET' undeclared
Add the missing include file and fix succeeding vdso errors.
Fixes: 09cfefb7fa70 ("LoongArch: Add memory management")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
The `vcsr` only exists in the old hardware design, it isn't used in any
shipped hardware from Loongson-3A5000 on. Both scalar FP and LSX/LASX
instructions use the `fcsr` as their control and status registers now.
For example, the RM control bit in fcsr0 is shared by FP, LSX and LASX
instructions.
Particularly, fcsr16 to fcsr31 are reserved for LSX/LASX now, access to
these registers has no visible effect if LSX/LASX is enabled, and will
cause SXD/ASXD exceptions if LSX/LASX is not enabled.
So, mentions of vcsr are obsolete in the first place (it was just used
for debugging), let's remove them.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Qi Hu <huqi@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Commit fa96b57c1490 ("LoongArch: Add build infrastructure") adds the new
file arch/loongarch/Kconfig.
As the work on LoongArch was probably quite some time under development,
various config symbols have changed and disappeared from the time of
initial writing of the Kconfig file and its inclusion in the repository.
The following four commits:
commit c126a53c2760 ("arch: remove GENERIC_FIND_FIRST_BIT entirely")
commit 140c8180eb7c ("arch: remove HAVE_COPY_THREAD_TLS")
commit aca52c398389 ("mm: remove CONFIG_HAVE_MEMBLOCK")
commit 3f08a302f533 ("mm: remove CONFIG_HAVE_MEMBLOCK_NODE_MAP option")
remove the mentioned config symbol, and enable the intended setup by
default without configuration.
Drop these obsolete selects in loongarch's Kconfig.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
compute_return_era() always returns 0, make it return void,
and then no need to check its return value for its callers.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
According to the configuration information accessible by the CPUCFG
instruction in LoongArch Reference Manual [1], FP_ver is stored in
bit [5: 3] of CPUCFG2, the current code to get fpu version is wrong,
use CPUCFG2_FPVERS to fix it.
[1] https://loongson.github.io/LoongArch-Documentation/LoongArch-Vol1-EN.html
Fixes: 628c3bb40e9a ("LoongArch: Add boot and setup routines")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
setup_tlb_handler() is expected to set per-cpu exception handlers, but
it only set the TLBRENTRY successfully because of copy & paste errors,
so fix it.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
_stext means the start of .text section (see __is_kernel_text()), but we
put its definition in .ref.text by mistake. Fix it by defining it in the
vmlinux.lds.S.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Fix the !THP build by making pmd_pfn() available in all configurations.
Because pmd_pfn() is used in mm/page_vma_mapped.c whether or not THP is
configured.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Commit c604abc3f6e ("vmlinux.lds.h: Split ELF_DETAILS from STABS_DEBUG")
splits ELF_DETAILS from STABS_DEBUG, resulting in missing ELF_DETAILS
information in LoongArch architecture, so add it.
Fixes: c604abc3f6e ("vmlinux.lds.h: Split ELF_DETAILS from STABS_DEBUG")
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
This comment block was taken originally from the MIPS architecture code,
where indeed there are particular assumptions one can make regarding SMP
and !SMP and cycle counters. On LoongArch, however, the rdtime family of
functions is always available. As Xuerui wrote:
The rdtime family of instructions is in fact guaranteed to be
available on LoongArch; LoongArch's subsets all contain them, even
the 32-bit "Primary" subset intended for university teaching -- they
provide the rdtimeh.w and rdtimel.w pair of instructions that access
the same 64-bit counter.
So this commit simply removes the incorrect comment block.
Link: https://lore.kernel.org/lkml/e78940bc-9be2-2fe7-026f-9e64a1416c9f@xen0n.name/
Fixes: b738c106f735 ("LoongArch: Add other common headers")
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Commit c5febea0956fd387 ("fork: Pass struct kernel_clone_args into
copy_thread") change the prototype of copy_thread(), while commit
5bd2e97c868a8a44 ("fork: Generalize PF_IO_WORKER handling") change
the structure of kernel_clone_args. They cause build errors, so fix it.
Fixes: 5bd2e97c868a8a44 ("fork: Generalize PF_IO_WORKER handling")
Fixes: c5febea0956fd387 ("fork: Pass struct kernel_clone_args into copy_thread")
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
1, We assume arch/loongarch/include/asm/smp.h be included in include/
linux/smp.h is valid and the reverse inclusion isn't. So remove the
<linux/smp.h> in arch/loongarch/include/asm/smp.h.
2, arch/loongarch/include/asm/smp.h is only needed when CONFIG_SMP,
and setup.c include it only because it need plat_smp_setup(). So,
reorganize setup.c & smp.h, and then remove <asm/smp.h> in setup.c.
3, Fix cacheinfo.c and percpu.h build error by adding the missing header
files when !CONFIG_SMP.
4, Fix acpi.c build error by adding CONFIG_SMP guards.
5, Move irq_stat definition from smp.c to irq.c and fix its declaration.
6, Select CONFIG_SMP for CONFIG_NUMA, similar as other architectures do.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Add Non-Uniform Memory Access (NUMA) support for LoongArch. LoongArch
has 48-bit physical address, but the HyperTransport I/O bus only support
40-bit address, so we need a custom phys_to_dma() and dma_to_phys() to
extract the 4-bit node id (bit 44~47) from Loongson-3's 48-bit physical
address space and embed it into 40-bit. In the 40-bit dma address, node
id offset can be read from the LS7A_DMA_CFG register.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
LoongArch-based procesors have 4, 8 or 16 cores per package. This patch
adds multi-processor (SMP) support for LoongArch.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Add VDSO and VSYSCALL support (sigreturn, gettimeofday and its friends)
for LoongArch.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
