IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Fix NULL-pointer dereference at open should the device lack a bulk-in or
bulk-out endpoint:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at iuu_open+0x78/0x59c [iuu_phoenix]
Fixes: 07c3b1a10016 ("USB: remove broken usb-serial num_endpoints
check")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Bind to the interface, but do not register any ports, after having
downloaded the firmware. The device will still disconnect and
re-enumerate, but this way we avoid an error messages from being logged
as part of the process:
io_ti: probe of 1-1.3:1.0 failed with error -5
Signed-off-by: Johan Hovold <johan@kernel.org>
Cancel the heartbeat work on driver unbind in order to avoid I/O after
disconnect in case the port is held open.
Note that the cancel in release() is still needed to stop the heartbeat
after late probe errors.
Fixes: 26c78daade0f ("USB: io_ti: Add heartbeat to keep idle EP/416
ports from disconnecting")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In case a device is left in "boot-mode" we must not register any port
devices in order to avoid a NULL-pointer dereference on open due to
missing endpoints. This could be used by a malicious device to trigger
an OOPS:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
[<bf0caa84>] (edge_open [io_ti]) from [<bf0b0118>] (serial_port_activate+0x68/0x98 [usbserial])
[<bf0b0118>] (serial_port_activate [usbserial]) from [<c0470ca4>] (tty_port_open+0x9c/0xe8)
[<c0470ca4>] (tty_port_open) from [<bf0b0da0>] (serial_open+0x48/0x6c [usbserial])
[<bf0b0da0>] (serial_open [usbserial]) from [<c0469178>] (tty_open+0xcc/0x5cc)
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference when clearing halt at open should a
malicious device lack the expected endpoints when in download mode.
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
[<bf011ed8>] (edge_open [io_ti]) from [<bf000118>] (serial_port_activate+0x68/0x98 [usbserial])
[<bf000118>] (serial_port_activate [usbserial]) from [<c0470ca4>] (tty_port_open+0x9c/0xe8)
[<c0470ca4>] (tty_port_open) from [<bf000da0>] (serial_open+0x48/0x6c [usbserial])
[<bf000da0>] (serial_open [usbserial]) from [<c0469178>] (tty_open+0xcc/0x5cc)
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference when initialising URBs at open should a
non-EPIC device lack a bulk-in or interrupt-in endpoint.
Unable to handle kernel NULL pointer dereference at virtual address 00000028
...
PC is at edge_open+0x24c/0x3e8 [io_edgeport]
Note that the EPIC-device probe path has the required sanity checks so
this makes those checks partially redundant.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to free the URB transfer buffer in case submission fails (e.g.
due to a disconnect).
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference when clearing halt at open should the device
lack a bulk-out endpoint.
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at cyberjack_open+0x40/0x9c [cyberjack]
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Stop Endpoint command can come at any point and we
have no control of that. We should make sure to
handle COMP_STOP on SETUP phase as well, otherwise
urb->actual_length might be set to negative values
in some occasions such as below:
urb->length = 4;
build_control_transfer_td_for(urb, ep);
stop_endpoint(ep);
COMP_STOP:
[...]
urb->actual_length = urb->length - trb->length;
trb->length is 8 for SETUP stage (8 control request
bytes), so actual_length would be set to -4 in this
case.
While doing that, also make sure to use TRB_TYPE
field of the actual TRB instead of matching pointers
to figure out in which stage of the control transfer
we got our completion event.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Apollo Lake also requires XHCI_PME_STUCK_QUIRK.
Adding its PCI ID to quirk.
Cc: <stable@vger.kernel.org>
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current abort operation has race.
xhci_handle_command_timeout()
xhci_abort_cmd_ring()
xhci_write_64(CMD_RING_ABORT)
xhci_handshake(5s)
do {
check CMD_RING_RUNNING
udelay(1)
...
COMP_CMD_ABORT event
COMP_CMD_STOP event
xhci_handle_stopped_cmd_ring()
restart cmd_ring
CMD_RING_RUNNING become 1 again
} while ()
return -ETIMEDOUT
xhci_write_64(CMD_RING_ABORT)
/* can abort random command */
To do abort operation correctly, we have to wait both of COMP_CMD_STOP
event and negation of CMD_RING_RUNNING.
But like above, while timeout handler is waiting negation of
CMD_RING_RUNNING, event handler can restart cmd_ring. So timeout
handler never be notice negation of CMD_RING_RUNNING, and retry of
CMD_RING_ABORT can abort random command (BTW, I guess retry of
CMD_RING_ABORT was workaround of this race).
To fix this race, this moves xhci_handle_stopped_cmd_ring() to
xhci_abort_cmd_ring(). And timeout handler waits COMP_CMD_STOP event.
At this point, timeout handler is owner of cmd_ring, and safely
restart cmd_ring by using xhci_handle_stopped_cmd_ring().
[FWIW, as bonus, this way would be easily extend to add CMD_RING_PAUSE
operation]
[locks edited as patch is rebased on other locking fixes -Mathias]
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is preparation to fix abort operation race (See "xhci: Fix race
related to abort operation"). To make timeout sleepable, use
delayed_work instead of timer.
[change a newly added pending timer fix to pending work -Mathias]
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In command timer function, xhci_handle_command_timeout(), xhci->lock
is unlocked before call into xhci_abort_cmd_ring(). This might cause
race between the timer function and the event handler.
The xhci_abort_cmd_ring() function sets the CMD_RING_ABORT bit in the
command register and polling it until the setting takes effect. A stop
command ring event might be handled between writing the abort bit and
polling for it. The event handler will restart the command ring, which
causes the failure of polling, and we ever believed that we failed to
stop it.
As a bonus, this also fixes some issues of calling functions without
locking in xhci_handle_command_timeout().
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we get a command completion event at the same time as the command
timeout work starts on another cpu we might end up aborting the wrong
command.
If the command completion takes the xhci lock before the timeout work, it
will handle the command, pick the next command, mark it as current_cmd, and
re-queue the timeout work. When the timeout work finally gets the lock
It will start aborting the wrong command.
This case can be resolved by checking if the timeout work is pending inside
the timeout function itself. A new timeout work can only be pending if the
command completed and a new command was queued.
If there are no more commands pending then command completion will set
the current_cmd to NULL, which is already handled in the timeout work.
Cc: <stable@vger.kernel.org>
Reported-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When current command was supposed to be aborted, host will free the command
in handle_cmd_completion() function. But it might be still referenced by
xhci->current_cmd, which need to set NULL.
Cc: <stable@vger.kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
handle_cmd_completion() frees a command structure which might be still
referenced by xhci->current_cmd.
This might cause problem when xhci->current_cmd is accessed after that.
A real-life case could be like this. The host takes a very long time to
respond to a command, and the command timer is fired at the same time
when the command completion event arrives. The command completion
handler frees xhci->current_cmd before the timer function can grab
xhci->lock. Afterward, timer function grabs the lock and go ahead with
checking and setting members of xhci->current_cmd.
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function xhci_mtk_probe(), variable ret takes the return value. Its
value should be negative on failures. However, when the call to function
platform_get_irq() fails, it does not set the error code, and 0 will be
returned. 0 indicates no error. As a result, the callers of function
xhci_mtk_probe() will not be able to detect the error. This patch fixes
the bug by assigning the return value of platform_get_irq() to variable
ret if it fails.
CC: <stable@vger.kernel.org>
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_setup_device() should return failure with correct error number
when xhci host has died, removed or halted.
During usb device enumeration, if usb host is not accessible (died,
removed or halted), the hc_driver->address_device() should return
a corresponding error code to usb core. But current xhci driver just
returns success. This misleads usb core to continue the enumeration
by reading the device descriptor, which will result in failure, and
users will get a misleading message like "device descriptor read/8,
error -110".
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the tt_info provided by a HS hub might be in use to by a child device
Make sure we free the devices in the correct order.
This is needed in special cases such as when xhci controller is
reset when resuming from hibernate, and all virt_devices are freed.
Also free the virt_devices starting from max slot_id as children
more commonly have higher slot_id than parent.
CC: <stable@vger.kernel.org>
Reported-by: Guenter Roeck <groeck@chromium.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an error message that was probably copied and pasted. The same
message is used for both the in and out endpoints, so it makes it impossible
to know which one actually failed because both cases say "IN".
Make the out endpoint error message say "OUT".
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DCFG.DEVSPD == 0x3 is not valid and we need to set
DCFG.DEVSPD to 0x1 for full speed mode. Same goes for
DSTS.CONNECTSPD.
Old databooks had 0x3 for full speed in 48MHz mode for
USB1.1 transceivers which was never supported. Newer databooks
don't mention 0x3 at all.
Cc: John Youn <John.Youn@synopsys.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With gcc 4.1.2:
drivers/usb/serial/f81534.c: In function ‘f81534_port_probe’:
drivers/usb/serial/f81534.c:1250: warning: comparison is always false due to limited range of data type
f81534_logic_to_phy_port() may return a negative error value, which is
ignored by assigning it to u8 f81534_port_private.phy_num.
Use an intermediate variable of type int to fix this.
While at it, forward the actual error code instead of converting it to
-ENODEV, and drop the useless check for F81534_NUM_PORT, as the callee
always returns a valid port number in case of success.
Fixes: 0c9bd6004d258d46 ("USB: serial: add Fintek F81532/534 driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Intel Gemini Lake SoC has the same DWC3 than Broxton. Add
the new ID to the supported Devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc2_hsotg_ep_enable can be called from interrupt context, so all
allocations should be done with GFP_ATOMIC flags. This fixes following
issue on ARM architecture:
[<c010d830>] (unwind_backtrace) from [<c010a51c>] (show_stack+0x10/0x14)
[<c010a51c>] (show_stack) from [<c032930c>] (dump_stack+0x74/0x94)
[<c032930c>] (dump_stack) from [<c011cd30>] (__warn+0xd4/0x100)
[<c011cd30>] (__warn) from [<c011cd7c>] (warn_slowpath_null+0x20/0x28)
[<c011cd7c>] (warn_slowpath_null) from [<c0187e04>] (smp_call_function_many+0xcc/0x2a4)
[<c0187e04>] (smp_call_function_many) from [<c0188014>] (on_each_cpu_mask+0x38/0xa8)
[<c0188014>] (on_each_cpu_mask) from [<c01ddfe0>] (start_isolate_page_range+0x134/0x1b8)
[<c01ddfe0>] (start_isolate_page_range) from [<c01a3c14>] (alloc_contig_range+0xac/0x2f8)
[<c01a3c14>] (alloc_contig_range) from [<c01de3e4>] (cma_alloc+0xe0/0x1a8)
[<c01de3e4>] (cma_alloc) from [<c0110acc>] (__alloc_from_contiguous+0x38/0xe0)
[<c0110acc>] (__alloc_from_contiguous) from [<c0110ba4>] (cma_allocator_alloc+0x30/0x38)
[<c0110ba4>] (cma_allocator_alloc) from [<c0111034>] (__dma_alloc+0x1c0/0x2c8)
[<c0111034>] (__dma_alloc) from [<c01111b4>] (arm_dma_alloc+0x3c/0x48)
[<c01111b4>] (arm_dma_alloc) from [<c04ad800>] (dwc2_hsotg_ep_enable+0xec/0x46c)
[<c04ad800>] (dwc2_hsotg_ep_enable) from [<c04da610>] (usb_ep_enable+0x2c/0x3c)
[<c04da610>] (usb_ep_enable) from [<c04dc0c0>] (ecm_set_alt+0xa8/0x154)
[<c04dc0c0>] (ecm_set_alt) from [<c04d678c>] (composite_setup+0xd74/0x1540)
[<c04d678c>] (composite_setup) from [<c04ae048>] (dwc2_hsotg_complete_setup+0xb8/0x370)
[<c04ae048>] (dwc2_hsotg_complete_setup) from [<c04d987c>] (usb_gadget_giveback_request+0xc/0x10)
[<c04d987c>] (usb_gadget_giveback_request) from [<c04acafc>] (dwc2_hsotg_complete_request+0x78/0x128)
[<c04acafc>] (dwc2_hsotg_complete_request) from [<c04aed28>] (dwc2_hsotg_epint+0x69c/0x81c)
[<c04aed28>] (dwc2_hsotg_epint) from [<c04af6c4>] (dwc2_hsotg_irq+0xfc/0x748)
[<c04af6c4>] (dwc2_hsotg_irq) from [<c0163264>] (__handle_irq_event_percpu+0x58/0x140)
[<c0163264>] (__handle_irq_event_percpu) from [<c0163368>] (handle_irq_event_percpu+0x1c/0x58)
[<c0163368>] (handle_irq_event_percpu) from [<c01633dc>] (handle_irq_event+0x38/0x5c)
[<c01633dc>] (handle_irq_event) from [<c01666e4>] (handle_fasteoi_irq+0xc4/0x19c)
[<c01666e4>] (handle_fasteoi_irq) from [<c0162a2c>] (generic_handle_irq+0x18/0x28)
[<c0162a2c>] (generic_handle_irq) from [<c0162b40>] (__handle_domain_irq+0x6c/0xe4)
[<c0162b40>] (__handle_domain_irq) from [<c0101470>] (gic_handle_irq+0x50/0x9c)
[<c0101470>] (gic_handle_irq) from [<c010b00c>] (__irq_svc+0x6c/0xa8)
Fixes: 5f54c54b0ba83 ("usb: dwc2: gadget: Add DDMA chain pointers to
dwc2_hsotg_ep structure")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Calling platform_device_add_properties() replaces existing properties so
the "linux,sysdev_is_parent" property doesn't get set. Add this property
to each platform.
Fixes: d64ff406e51e ("usb: dwc3: use bus->sysdev for DMA configuration")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now races can happen between interrupt handler execution and PM runtime in
error handling code path in probe and in dwc3_omap_remove() which will lead
to system crash:
in probe:
...
err1:
pm_runtime_put_sync(dev);
^^ PM runtime can race with IRQ handler when deferred probing happening
due to extcon
pm_runtime_disable(dev);
return ret;
in dwc3_omap_remove:
...
dwc3_omap_disable_irqs(omap);
^^ IRQs are disabled in HW, but handler may still run
of_platform_depopulate(omap->dev);
pm_runtime_put_sync(&pdev->dev);
^^ PM runtime can race with IRQ handler
pm_runtime_disable(&pdev->dev);
return 0;
So, OMAP DWC3 IRQ need to be disabled before calling
pm_runtime_put() in probe and in dwc3_omap_remove().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dev_config() routine in gadgetfs has a check that
dev->dev->bNumConfigurations is equal to 1, and then contains a
redundant line of code setting the value to 1. This patch removes the
unnecessary assignment.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Andrey Konovalov's fuzz testing of gadgetfs showed that we should
improve the driver's checks for valid configuration descriptors passed
in by the user. In particular, the driver needs to verify that the
wTotalLength value in the descriptor is not too short (smaller
than USB_DT_CONFIG_SIZE). And the check for whether wTotalLength is
too large has to be changed, because the driver assumes there is
always enough room remaining in the buffer to hold a device descriptor
(at least USB_DT_DEVICE_SIZE bytes).
This patch adds the additional check and fixes the existing check. It
may do a little more than strictly necessary, but one extra check
won't hurt.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Andrey Konovalov reports that fuzz testing with syzkaller causes a
KASAN use-after-free bug report in gadgetfs:
BUG: KASAN: use-after-free in gadgetfs_setup+0x208a/0x20e0 at addr ffff88003dfe5bf2
Read of size 2 by task syz-executor0/22994
CPU: 3 PID: 22994 Comm: syz-executor0 Not tainted 4.9.0-rc7+ #16
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
ffff88006df06a18 ffffffff81f96aba ffffffffe0528500 1ffff1000dbe0cd6
ffffed000dbe0cce ffff88006df068f0 0000000041b58ab3 ffffffff8598b4c8
ffffffff81f96828 1ffff1000dbe0ccd ffff88006df06708 ffff88006df06748
Call Trace:
<IRQ> [ 201.343209] [< inline >] __dump_stack lib/dump_stack.c:15
<IRQ> [ 201.343209] [<ffffffff81f96aba>] dump_stack+0x292/0x398 lib/dump_stack.c:51
[<ffffffff817e4dec>] kasan_object_err+0x1c/0x70 mm/kasan/report.c:159
[< inline >] print_address_description mm/kasan/report.c:197
[<ffffffff817e5080>] kasan_report_error+0x1f0/0x4e0 mm/kasan/report.c:286
[< inline >] kasan_report mm/kasan/report.c:306
[<ffffffff817e562a>] __asan_report_load_n_noabort+0x3a/0x40 mm/kasan/report.c:337
[< inline >] config_buf drivers/usb/gadget/legacy/inode.c:1298
[<ffffffff8322c8fa>] gadgetfs_setup+0x208a/0x20e0 drivers/usb/gadget/legacy/inode.c:1368
[<ffffffff830fdcd0>] dummy_timer+0x11f0/0x36d0 drivers/usb/gadget/udc/dummy_hcd.c:1858
[<ffffffff814807c1>] call_timer_fn+0x241/0x800 kernel/time/timer.c:1308
[< inline >] expire_timers kernel/time/timer.c:1348
[<ffffffff81482de6>] __run_timers+0xa06/0xec0 kernel/time/timer.c:1641
[<ffffffff814832c1>] run_timer_softirq+0x21/0x80 kernel/time/timer.c:1654
[<ffffffff84f4af8b>] __do_softirq+0x2fb/0xb63 kernel/softirq.c:284
The cause of the bug is subtle. The dev_config() routine gets called
twice by the fuzzer. The first time, the user data contains both a
full-speed configuration descriptor and a high-speed config
descriptor, causing dev->hs_config to be set. But it also contains an
invalid device descriptor, so the buffer containing the descriptors is
deallocated and dev_config() returns an error.
The second time dev_config() is called, the user data contains only a
full-speed config descriptor. But dev->hs_config still has the stale
pointer remaining from the first call, causing the routine to think
that there is a valid high-speed config. Later on, when the driver
dereferences the stale pointer to copy that descriptor, we get a
use-after-free access.
The fix is simple: Clear dev->hs_config if the passed-in data does not
contain a high-speed config descriptor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Andrey Konovalov reports that fuzz testing with syzkaller causes a
KASAN warning in gadgetfs:
BUG: KASAN: slab-out-of-bounds in dev_config+0x86f/0x1190 at addr ffff88003c47e160
Write of size 65537 by task syz-executor0/6356
CPU: 3 PID: 6356 Comm: syz-executor0 Not tainted 4.9.0-rc7+ #19
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
ffff88003c107ad8 ffffffff81f96aba ffffffff3dc11ef0 1ffff10007820eee
ffffed0007820ee6 ffff88003dc11f00 0000000041b58ab3 ffffffff8598b4c8
ffffffff81f96828 ffffffff813fb4a0 ffff88003b6eadc0 ffff88003c107738
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff81f96aba>] dump_stack+0x292/0x398 lib/dump_stack.c:51
[<ffffffff817e4dec>] kasan_object_err+0x1c/0x70 mm/kasan/report.c:159
[< inline >] print_address_description mm/kasan/report.c:197
[<ffffffff817e5080>] kasan_report_error+0x1f0/0x4e0 mm/kasan/report.c:286
[<ffffffff817e5705>] kasan_report+0x35/0x40 mm/kasan/report.c:306
[< inline >] check_memory_region_inline mm/kasan/kasan.c:308
[<ffffffff817e3fb9>] check_memory_region+0x139/0x190 mm/kasan/kasan.c:315
[<ffffffff817e4044>] kasan_check_write+0x14/0x20 mm/kasan/kasan.c:326
[< inline >] copy_from_user arch/x86/include/asm/uaccess.h:689
[< inline >] ep0_write drivers/usb/gadget/legacy/inode.c:1135
[<ffffffff83228caf>] dev_config+0x86f/0x1190 drivers/usb/gadget/legacy/inode.c:1759
[<ffffffff817fdd55>] __vfs_write+0x5d5/0x760 fs/read_write.c:510
[<ffffffff817ff650>] vfs_write+0x170/0x4e0 fs/read_write.c:560
[< inline >] SYSC_write fs/read_write.c:607
[<ffffffff81803a5b>] SyS_write+0xfb/0x230 fs/read_write.c:599
[<ffffffff84f47ec1>] entry_SYSCALL_64_fastpath+0x1f/0xc2
Indeed, there is a comment saying that the value of len is restricted
to a 16-bit integer, but the code doesn't actually do this.
This patch fixes the warning. It replaces the comment with a
computation that forces the amount of data copied from the user in
ep0_write() to be no larger than the wLength size for the control
transfer, which is a 16-bit quantity.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case EP disabled pass only EPCPLT command
to be handled. In other case we could hit
Bug like below.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000003
IP:
[<ffffffff81673428>] dwc3_thread_interrupt+0x11c8/0x1790
while dep->endpoint.desc is NULL.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Andrey Konovalov reported that we were not properly checking the upper
limit before of a device configuration size before calling
memdup_user(), which could cause some problems.
So set the upper limit to PAGE_SIZE * 4, which should be good enough for
all devices.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The stop_activity() routine in dummy-hcd is supposed to unlink all
active requests for every endpoint, among other things. But it
doesn't handle ep0. As a result, fuzz testing can generate a WARNING
like the following:
WARNING: CPU: 0 PID: 4410 at drivers/usb/gadget/udc/dummy_hcd.c:672 dummy_free_request+0x153/0x170
Modules linked in:
CPU: 0 PID: 4410 Comm: syz-executor Not tainted 4.9.0-rc7+ #32
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
ffff88006a64ed10 ffffffff81f96b8a ffffffff41b58ab3 1ffff1000d4c9d35
ffffed000d4c9d2d ffff880065f8ac00 0000000041b58ab3 ffffffff8598b510
ffffffff81f968f8 0000000041b58ab3 ffffffff859410e0 ffffffff813f0590
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51
[<ffffffff812b808f>] __warn+0x19f/0x1e0 kernel/panic.c:550
[<ffffffff812b831c>] warn_slowpath_null+0x2c/0x40 kernel/panic.c:585
[<ffffffff830fcb13>] dummy_free_request+0x153/0x170 drivers/usb/gadget/udc/dummy_hcd.c:672
[<ffffffff830ed1b0>] usb_ep_free_request+0xc0/0x420 drivers/usb/gadget/udc/core.c:195
[<ffffffff83225031>] gadgetfs_unbind+0x131/0x190 drivers/usb/gadget/legacy/inode.c:1612
[<ffffffff830ebd8f>] usb_gadget_remove_driver+0x10f/0x2b0 drivers/usb/gadget/udc/core.c:1228
[<ffffffff830ec084>] usb_gadget_unregister_driver+0x154/0x240 drivers/usb/gadget/udc/core.c:1357
This patch fixes the problem by iterating over all the endpoints in
the driver's ep array instead of iterating over the gadget's ep_list,
which explicitly leaves out ep0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reserved1 is documented as expected to be set to 0, but this test fails
when it it set to 0. Reverse the condition.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When FUNCTIONFS_EVENTFD flag is set, __ffs_data_got_descs reads a 32bits,
little-endian value right after the fixed structure header, and passes it
to eventfd_ctx_fdget. Document this.
Also, rephrase a comment to be affirmative about the role of string
descriptor at index 0. Ref: USB 2.0 spec paragraph "9.6.7 String", and
also checked to still be current in USB 3.0 spec paragraph "9.6.9 String".
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By convention (according to doc) if function does not provide
get_alt() callback composite framework should assume that it has only
altsetting 0 and should respond with error if host tries to set
other one.
After commit dd4dff8b035f ("USB: composite: Fix bug: should test
set_alt function pointer before use it")
we started checking set_alt() callback instead of get_alt().
This check is useless as we check if set_alt() is set inside
usb_add_function() and fail if it's NULL.
Let's fix this check and move comment about why we check the get
method instead of set a little bit closer to prevent future false
fixes.
Fixes: dd4dff8b035f ("USB: composite: Fix bug: should test set_alt function pointer before use it")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb_get_dr_mode() expects the device-property to be spelled
"dr_mode" not "dr-mode".
Spelling it properly fixes the following warning showing up in dmesg:
[ 8704.500545] dwc3 dwc3.2.auto: Configuration mismatch. dr_mode forced to gadget
Signed-off-by: Hans de Goede <hdegoede@redhat.com
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we're handling so many transfers at a time
and for some dwc3 revisions LPM events *must* be
enabled, we can fall into a situation where too many
events fire and we start receiving Overflow events.
Let's do what XHCI does and allocate a full page for
the Event Ring, this will avoid any future issues.
Cc: <stable@vger.kernel.org> # v4.9
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit 0416e494ce7d ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced") introduced a bug
where we would leak DMA resources which would cause
us to starve the system of them resulting in failing
DMA transfers.
Fix the bug by making sure that we always unmap EP0
requests since those are *always* mapped.
Fixes: 0416e494ce7d ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced")
Cc: <stable@vger.kernel.org>
Tested-by: Tomasz Medrek <tomaszx.medrek@intel.com>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Let's call dwc3_ep0_prepare_one_trb() explicitly
because there are occasions where we will need more
than one TRB to handle an EP0 transfer.
A follow-up patch will fix one bug related to
multiple-TRB Data Phases when it comes to
mapping/unmapping requests for DMA.
Cc: <stable@vger.kernel.org>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For now this is just a cleanup patch, no functional
changes. We will be using the new function to fix a
bug introduced long ago by commit 0416e494ce7d
("usb: dwc3: ep0: correct cache sync issue in case
of ep0_bounced") and further worsened by commit
c0bd5456a470 ("usb: dwc3: ep0: handle non maxpacket
aligned transfers > 512")
Cc: <stable@vger.kernel.org>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current default for gadget DMA descriptor results on bcm2835 in a
unnecessary error message:
Invalid value 1 for param gadget-dma-desc
So fix this by using hw->dma_desc_enable as default value.
Fixes: dec4b55677e ("usb: dwc2: gadget: Add descriptor DMA parameter")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current defaults for DMA results on a non-DMA platform in a unnecessary
error message:
Invalid value 0 for param gadget-dma
So fix this by using dma_capable as default value.
Fixes: 9962b62f1be ("usb: dwc2: Deprecate g-use-dma binding")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to the Devicetree ePAPR [1] the datatypes u8 and u16 are
not defined. So using device_property_read_u16() would result in
a partial read of a 32-bit big-endian integer which is not intended.
So we better read the complete 32-bit value. This fixes a regression
on bcm2835 where the values for g-rx-fifo-size and g-np-tx-fifo-size
always read as zero:
Invalid value 0 for param g-rx-fifo-size
Invalid value 0 for param g-np-tx-fifo-size
[1] - http://elinux.org/images/c/cf/Power_ePAPR_APPROVED_v1.1.pdf
Fixes: 05ee799f202 ("usb: dwc2: Move gadget settings into core_params")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since commit "usb: dwc2: Improve handling of host and device hwparams" the
host mode specific hardware parameter aren't initialized in peripheral mode
from the register settings anymore. So we better do not set them in this
case which avoids the following warnings on bcm2835:
256 invalid for host_nperio_tx_fifo_size. Check HW configuration.
512 invalid for host_perio_tx_fifo_size. Check HW configuration.
Fixes: 55e1040e424b ("usb: dwc2: Improve handling of host and device hwparams")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
