IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This renames get_adv_instance_scan_rsp to adv_instance_is_scannable and
make it return a bool since it was not actually properly return the size
of the scan response as one could expect.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Current code is actually failing on the following tests of mgmt-tester
because get_adv_instance_scan_rsp_len did not account for flags that
cause scan response data to be included resulting in non-scannable
instance when in fact it should be scannable.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This test case is meant to verify that multiple
unknown options is included in the response.
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 3, Part A
page 1057
'On an unknown option failure (Result=0x0003),
the option(s) that contain anoption type field that is not
understood by the recipient of the L2CAP_CONFIGURATION_REQ
packet shall be included in the L2CAP_CONFIGURATION_RSP
packet unless they are hints.'
Before this patch:
> ACL Data RX: Handle 11 flags 0x02 dlen 24
L2CAP: Configure Request (0x04) ident 18 len 16
Destination CID: 64
Flags: 0x0000
Option: Unknown (0x10) [mandatory]
10 00 11 02 11 00 12 02 12 00
< ACL Data TX: Handle 11 flags 0x00 dlen 17
L2CAP: Configure Response (0x05) ident 18 len 9
Source CID: 64
Flags: 0x0000
Result: Failure - unknown options (0x0003)
Option: Unknown (0x10) [mandatory]
12
After this patch:
> ACL Data RX: Handle 11 flags 0x02 dlen 24
L2CAP: Configure Request (0x04) ident 5 len 16
Destination CID: 64
Flags: 0x0000
Option: Unknown (0x10) [mandatory]
10 00 11 02 11 00 12 02 12 00
< ACL Data TX: Handle 11 flags 0x00 dlen 23
L2CAP: Configure Response (0x05) ident 5 len 15
Source CID: 64
Flags: 0x0000
Result: Failure - unknown options (0x0003)
Option: Unknown (0x10) [mandatory]
10 11 01 11 12 01 12
Signed-off-by: Jimmy Wahlberg <jimmywa@spotify.com>
Reviewed-by: Luiz Augusto Von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This replaces the BT_DBG function to bt_dev_dbg as it is cleaner to show
the controller index in the debug message.
Signed-off-by: Howard Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to the spec Ver 5.2, Vol 3, Part C, Sec 5.2.2.8:
Device in security mode 4 level 4 shall enforce:
128-bit equivalent strength for link and encryption keys required
using FIPS approved algorithms (E0 not allowed, SAFER+ not allowed,
and P-192 not allowed; encryption key not shortened)
This patch rejects connection with key size below 16 for FIPS
level services.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A different wait queue was used when removing ctrl_wait than when adding
it. This effectively made the remove operation without locking compared
to other operations on the wait queue ctrl_wait was part of. This caused
issues like below where dead000000000100 is LIST_POISON1 and
dead000000000200 is LIST_POISON2.
list_add corruption. next->prev should be prev (ffffffc1b0a33a08), \
but was dead000000000200. (next=ffffffc03ac77de0).
------------[ cut here ]------------
CPU: 3 PID: 2138 Comm: bluetoothd Tainted: G O 4.4.238+ #9
...
---[ end trace 0adc2158f0646eac ]---
Call trace:
[<ffffffc000443f78>] __list_add+0x38/0xb0
[<ffffffc0000f0d04>] add_wait_queue+0x4c/0x68
[<ffffffc00020eecc>] __pollwait+0xec/0x100
[<ffffffc000d1556c>] bt_sock_poll+0x74/0x200
[<ffffffc000bdb8a8>] sock_poll+0x110/0x128
[<ffffffc000210378>] do_sys_poll+0x220/0x480
[<ffffffc0002106f0>] SyS_poll+0x80/0x138
[<ffffffc00008510c>] __sys_trace_return+0x0/0x4
Unable to handle kernel paging request at virtual address dead000000000100
...
CPU: 4 PID: 5387 Comm: kworker/u15:3 Tainted: G W O 4.4.238+ #9
...
Call trace:
[<ffffffc0000f079c>] __wake_up_common+0x7c/0xa8
[<ffffffc0000f0818>] __wake_up+0x50/0x70
[<ffffffc000be11b0>] sock_def_wakeup+0x58/0x60
[<ffffffc000de5e10>] l2cap_sock_teardown_cb+0x200/0x224
[<ffffffc000d3f2ac>] l2cap_chan_del+0xa4/0x298
[<ffffffc000d45ea0>] l2cap_conn_del+0x118/0x198
[<ffffffc000d45f8c>] l2cap_disconn_cfm+0x6c/0x78
[<ffffffc000d29934>] hci_event_packet+0x564/0x2e30
[<ffffffc000d19b0c>] hci_rx_work+0x10c/0x360
[<ffffffc0000c2218>] process_one_work+0x268/0x460
[<ffffffc0000c2678>] worker_thread+0x268/0x480
[<ffffffc0000c94e0>] kthread+0x118/0x128
[<ffffffc000085070>] ret_from_fork+0x10/0x20
---[ end trace 0adc2158f0646ead ]---
Signed-off-by: Ole Bjørn Midtbø <omidtbo@cisco.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Avoid multiple attempts to create the debugfs entry, force_bredr_smp,
by moving it from the SMP registration to the BR/EDR controller init
section. hci_debugfs_create_bredr is only called when HCI_SETUP and
HCI_CONFIG is not set.
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When adding device to white list the device is added to resolving list
also. It has to be added only when HCI_ENABLE_LL_PRIVACY flag is set.
HCI_ENABLE_LL_PRIVACY flag has to be tested before adding/deleting devices
to resolving list. use_ll_privacy macro is used only to check if controller
supports LL_Privacy.
https://bugzilla.kernel.org/show_bug.cgi?id=209745
Fixes: 0eee35bdfa3b ("Bluetooth: Update resolving list when updating whitelist")
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When an LE connection request is made, advertising is disabled and never
resumed. When a client has an active advertisement, this is disruptive.
This change adds resume logic for client-configured (non-directed)
advertisements after the connection attempt.
The patch was tested by registering an advertisement, initiating an LE
connection from a remote peer, and verifying that the advertisement is
re-activated after the connection is established. This is performed on
Hatch and Kukui Chromebooks.
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
AMP_MGR is getting derefernced in hci_phy_link_complete_evt(), when called
from hci_event_packet() and there is a possibility, that hcon->amp_mgr may
not be found when accessing after initialization of hcon.
- net/bluetooth/hci_event.c:4945
The bug seems to get triggered in this line:
bredr_hcon = hcon->amp_mgr->l2cap_conn->hcon;
Fix it by adding a NULL check for the hcon->amp_mgr before checking the ev-status.
Fixes: d5e911928bd8 ("Bluetooth: AMP: Process Physical Link Complete evt")
Reported-and-tested-by: syzbot+0bef568258653cff272f@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=0bef568258653cff272f
Signed-off-by: Anmol Karn <anmol.karan123@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-09-29
Here's the main bluetooth-next pull request for 5.10:
- Multiple fixes to suspend/resume handling
- Added mgmt events for controller suspend/resume state
- Improved extended advertising support
- btintel: Enhanced support for next generation controllers
- Added Qualcomm Bluetooth SoC WCN6855 support
- Several other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This checks if BT_HS is enabled relecting it on MGMT_SETTING_HS instead
of always reporting it as supported.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth High Speed requires hardware support which is very uncommon
nowadays since HS has not pickup interest by the industry.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only sockets will have the chan->data set to an actual sk, channels
like A2MP would have its own data which would likely cause a crash when
calling sk_filter, in order to fix this a new callback has been
introduced so channels can implement their own filtering if necessary.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes various places where a stack variable is used uninitialized.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During system powercycle when trying to get the random address
hci_get_random_address set own_addr_type as 0x01. In which if we enable
ll_privacy it is supposed to be 0x03.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the code auto-creates hci_conn only if the remote address has
been discovered before. This may not be the case. For example, the
remote device may trigger connection after reboot at already-paired
state so there is no inquiry result found, but it is still correct to
create the hci_conn when Connection Complete event is received.
A better guard is to check against bredr allowlist. Devices in the
allowlist have been given permission to auto-connect.
Fixes: 4f40afc6c764 ("Bluetooth: Handle BR/EDR devices during suspend")
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Set scan parameters when there is at least one Advertisement monitor.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes the count of Adv monitor upon monitor removal.
The following test was performed.
- Start two btmgmt consoles, issue a btmgmt advmon-remove command on one
console and observe a MGMT_EV_ADV_MONITOR_REMOVED event on the other.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Drop repeated words in net/bluetooth/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the controller will continue advertising when the system
enters suspend. This patch makes sure that all advertising instances are
paused when entering suspend, and resumed when suspend exits.
The Advertising and Suspend/Resume test suites were both run on this
change on 4.19 kernel with both hardware offloaded multi-advertising and
software rotated multi-advertising. In addition, a new test was added
that performs the following steps:
* Register 3 advertisements via bluez RegisterAdvertisement
* Verify reception of all advertisements by remote peer
* Enter suspend on DUT
* Verify failure to receive all advertisements by remote peer
* Exit suspend on DUT
* Verify reception of all advertisements by remote peer
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Emit controller suspend and resume events when we are ready for suspend
and we've resumed from suspend.
The controller suspend event will report whatever suspend state was
successfully entered. The controller resume event will check the first
HCI event that was received after we finished preparing for suspend and,
if it was a connection event, store the address of the peer that caused
the event. If it was not a connection event, we mark the wake reason as
an unexpected event.
Here is a sample btmon trace with these events:
@ MGMT Event: Controller Suspended (0x002d) plen 1
Suspend state: Page scanning and/or passive scanning (2)
@ MGMT Event: Controller Resumed (0x002e) plen 8
Wake reason: Remote wake due to peer device connection (2)
LE Address: CD:F3:CD:13:C5:9A (OUI CD-F3-CD)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the controller suspend and resume events, which will signal when
Bluetooth has completed preparing for suspend and when it's ready for
resume.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only set extended scan response only when it exists. Otherwise, clear
the scan response data.
Per the core spec v5.2, Vol 4, Part E, 7.8.55
If the advertising set is non-scannable and the Host uses this command
other than to discard existing data, the Controller shall return the
error code Invalid HCI Command Parameters (0x12).
On WCN3991, the controller correctly responds with Invalid Parameters
when this is sent. That error causes __hci_req_hci_power_on to fail
with -EINVAL and LE devices can't connect because background scanning
isn't configured.
Here is an hci trace of where this issue occurs during power on:
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
Handle: 0x00
Properties: 0x0010
Use legacy advertising PDUs: ADV_NONCONN_IND
Min advertising interval: 181.250 msec (0x0122)
Max advertising interval: 181.250 msec (0x0122)
Channel map: 37, 38, 39 (0x07)
Own address type: Random (0x01)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Filter policy: Allow Scan Request from Any, Allow Connect...
TX power: 127 dbm (0x7f)
Primary PHY: LE 1M (0x01)
Secondary max skip: 0x00
Secondary PHY: LE 1M (0x01)
SID: 0x00
Scan request notifications: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 5
LE Set Extended Advertising Parameters (0x08|0x0036) ncmd 1
Status: Success (0x00)
TX power (selected): 9 dbm (0x09)
< HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7
Advertising handle: 0x00
Advertising random address: 08:FD:55:ED:22:28 (OUI 08-FD-55)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertising Set Random Address (0x08|0x0035) ncmd
Status: Success (0x00)
< HCI Command: LE Set Extended Scan Response Data (0x08|0x0038) plen 35
Handle: 0x00
Operation: Complete scan response data (0x03)
Fragment preference: Minimize fragmentation (0x01)
Data length: 0x0d
Name (short): Chromebook
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Response Data (0x08|0x0038) ncmd 1
Status: Invalid HCI Command Parameters (0x12)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For new advertising features, it will be important for userspace to
know the capabilities of the controller and kernel. If the controller
and kernel support extended advertising, we include flags indicating
hardware offloading support and support for setting tx power of adv
instances.
In the future, vendor-specific commands may allow the setting of tx
power in advertising instances, but for now this feature is only
marked available if extended advertising is supported.
This change is manually verified in userspace by ensuring the
advertising manager's supported_flags field is updated with new flags on
hatch chromebook (ext advertising supported).
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Here we make sure we properly report the number of supported
advertising slots when we are using hardware offloading. If no
hardware offloading is available, we default this value to
HCI_MAX_ADV_INSTANCES for use in software rotation as before.
This change has been tested on kukui (no ext adv) and hatch (ext adv)
chromebooks by verifying "SupportedInstances" shows 5 (the default) and
6 (slots supported by controller), respectively.
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch defines new getsockopt options BT_SNDMTU/BT_RCVMTU
for SCO socket to be compatible with other bluetooth sockets.
These new options return the same value as option SCO_OPTIONS
which is already present on existing kernels.
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Unregister_pm_notifier is a blocking call so suspend tasks should be
cleared beforehand. Otherwise, the notifier will wait for completion
before returning (and we encounter a 2s timeout on resume).
Fixes: 0e9952804ec9c8 (Bluetooth: Clear suspend tasks on unregister)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
While unregistering, make sure to clear the suspend tasks before
cancelling the work. If the unregister is called during resume from
suspend, this will unnecessarily add 2s to the resume time otherwise.
Fixes: 4e8c36c3b0d73d (Bluetooth: Fix suspend notifier race)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[akpm@linux-foundation.org: fs/crypto/inline_crypt.c needs linux/slab.h]
[akpm@linux-foundation.org: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Joe Perches <joe@perches.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Link: http://lkml.kernel.org/r/20200616154311.12314-3-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Resolved kernel/bpf/btf.c using instructions from merge commit
69138b34a7248d2396ab85c8652e20c0c39beaba
Signed-off-by: David S. Miller <davem@davemloft.net>
net/bluetooth/sco.c: In function ‘sco_sock_setsockopt’:
net/bluetooth/sco.c:862:3: error: cannot convert to a pointer type
862 | if (get_user(opt, (u32 __user *)optval)) {
| ^~
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-07-31
Here's the main bluetooth-next pull request for 5.9:
- Fix firmware filenames for Marvell chipsets
- Several suspend-related fixes
- Addedd mgmt commands for runtime configuration
- Multiple fixes for Qualcomm-based controllers
- Add new monitoring feature for mgmt
- Fix handling of legacy cipher (E4) together with security level 4
- Add support for Realtek 8822CE controller
- Fix issues with Chinese controllers using fake VID/PID values
- Multiple other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag CRYPTO_ALG_INTERNAL is not meant to be used outside of
the Crypto API. It isn't needed here anyway.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Increment the mgmt revision due to the recently added new commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When an LE connection is requested and an RPA update is needed via
hci_connect_le_scan, the default scanning parameters are used rather
than the connect parameters. This leads to significant delays in the
connection establishment process when using lower duty cycle scanning
parameters.
The patch simply looks at the pended connection list when trying to
determine which scanning parameters should be used.
Before:
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
#378 [hci0] 1659.247156
Own address type: Public (0x00)
Filter policy: Ignore not in white list (0x01)
PHYs: 0x01
Entry 0: LE 1M
Type: Passive (0x00)
Interval: 367.500 msec (0x024c)
Window: 37.500 msec (0x003c)
After:
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
#39 [hci0] 7.422109
Own address type: Public (0x00)
Filter policy: Ignore not in white list (0x01)
PHYs: 0x01
Entry 0: LE 1M
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 60.000 msec (0x0060)
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Yu Liu <yudiliu@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support to enable the use of RPA Address resolution
using expermental feature mgmt command.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enable RPA timeout during bluetooth initialization.
The RPA timeout value is used from hdev, which initialized from
debug_fs
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In this patch if le_create_conn process is started restrict to
disable address resolution and same is disabled during
le_enh_connection_complete
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When address resolution is enabled and set_privacy is enabled let's
use own address type as 0x03
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using controller based address resolution, then the new address
types 0x02 and 0x03 are used. These types need to be converted back into
either public address or random address types.
This patch is specially during LE_CREATE_CONN if using own_add_type as 0x02
or 0x03.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
