IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
last_rate is initialized to zero by sta_info_alloc(), but
this indicates legacy bitrate for the last TX rate (and
invalid for the last RX rate). To avoid a warning when
decoding the last rate as legacy (before a data frame
has been sent), initialize them as S1G MCS.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20201005164522.18069-2-thomas@adapt-ip.com
[rename to ieee80211_s1g_sta_rate_init(), seems more appropriate]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even though a driver or mac80211 shouldn't produce a
legacy bitrate if sband->bitrates doesn't exist, don't
crash if that is the case either.
This fixes a kernel panic if station dump is run before
last_rate can be updated with a data frame when
sband->bitrates is missing (eg. in S1G bands).
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20201005164522.18069-1-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CAN Transport Protocols offer support for segmented Point-to-Point
communication between CAN nodes via two defined CAN Identifiers.
As CAN frames can only transport a small amount of data bytes
(max. 8 bytes for 'classic' CAN and max. 64 bytes for CAN FD) this
segmentation is needed to transport longer PDUs as needed e.g. for
vehicle diagnosis (UDS, ISO 14229) or IP-over-CAN traffic.
This protocol driver implements data transfers according to
ISO 15765-2:2016 for 'classic' CAN and CAN FD frame types.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20200928200404.82229-1-socketcan@hartkopp.net
[mkl: Removed "WITH Linux-syscall-note" from isotp.c.
Fixed indention, a checkpatch warning and typos.
Replaced __u{8,32} by u{8,32}.
Removed always false (optlen < 0) check in isotp_setsockopt().]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For now, this function simply aligns the data at the beginning of the
pages. This can eventually be expanded to shift data to the correct
offsets when we're ready.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
This patch adds the ability to "read a hole" into a set of XDR data
pages by taking the following steps:
1) Shift all data after the current xdr->p to the right, possibly into
the tail,
2) Zero the specified range, and
3) Update xdr->p to point beyond the hole.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
xdr_shrink_pagelen() is very similar to what we need for hole expansion,
so split out the common code into its own function that can be used by
both functions.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
I don't need the entire align pages code for READ_PLUS, so split out the
part I do need so I don't need to reimplement anything.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
I'll need this for READ_PLUS to help figure out the offset where page
data is stored at, but it might also be useful for other things.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
I'm going to need this bit of code in a few places for READ_PLUS
decoding, so let's make it a helper function.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Error queue are not yet implemented in CAN-raw sockets.
The problem: a userland call to recvmsg(soc, msg, MSG_ERRQUEUE) on a
CAN-raw socket would unqueue messages from the normal queue without
any kind of error or warning. As such, it prevented CAN drivers from
using the functionalities that relies on the error queue such as
skb_tx_timestamp().
SCM_CAN_RAW_ERRQUEUE is defined as the type for the CAN raw error
queue. SCM stands for "Socket control messages". The name is inspired
from SCM_J1939_ERRQUEUE of include/uapi/linux/can/j1939.h.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20200926162527.270030-1-mailhol.vincent@wanadoo.fr
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the kernel doc for can_rcv_list_find() which was broken in commit:
3ee6d2bebe ("can: af_can: rename find_rcv_list() to can_rcv_list_find()")
while renaming a variable, but forgetting to rename the kernel doc, too.
Link: http://lore.kernel.org/r/20201006203748.1750156-2-mkl@pengutronix.de
Fixes: 3ee6d2bebe ("can: af_can: rename find_rcv_list() to can_rcv_list_find()")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Perform header flags validation through the policy.
Only pause command supports ETHTOOL_FLAG_STATS. Create a separate
policy to be able to express that in policy dumps to user space.
Note that even though the core will validate the header policy,
it cannot record multiple layers of attributes and we have to
re-parse header sub-attrs. When doing so we could skip attribute
validation, or use most permissive policy. Opt for the former.
We will no longer return the extack cookie for flags but since
we only added first new flag in this release it's not expected
that any user space had a chance to make use of it.
v2: - remove the re-validation in ethnl_parse_header_dev_get()
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't have good validation policy for existing unsigned int attrs
which serve as flags (for new ones we could use NLA_BITFIELD32).
With increased use of policy dumping having the validation be
expressed as part of the policy is important. Add validation
policy in form of a mask of supported/valid bits.
Support u64 in the uAPI to be future-proof, but really for now
the embedded mask member can only hold 32 bits, so anything with
bit 32+ set will always fail validation.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To get the most out of parsing by the core, and to allow dumping
full policies we need to specify which policy applies to nested
attrs. For headers it's ethnl_header_policy.
$ sed -i 's@\(ETHTOOL_A_.*HEADER\].*=\) { .type = NLA_NESTED },@\1\n\t\tNLA_POLICY_NESTED(ethnl_header_policy),@' net/ethtool/*
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ethtool uses strict attribute validation there's no need
to initialize all attributes in policy tables. 0 is NLA_UNSPEC
which is going to be rejected. Remove the NLA_REJECTs.
Similarly attributes above maxattrs are rejected, so there's
no need to always size the policy tables to ETHTOOL_A_..._MAX.
v2: - new patch
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to get commands wire up the policies of set commands
to get parsing by the core and policy dumps.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wire up policies for get commands in struct nla_policy of the ethtool
family. Make use of genetlink code attr validation and parsing, as well
as allow dumping policies to user space.
For every ETHTOOL_MSG_*_GET:
- add 'ethnl_' prefix to policy name
- add extern declaration in net/ethtool/netlink.h
- wire up the policy & attr in ethtool_genl_ops[].
- remove .request_policy and .max_attr from ethnl_request_ops.
Obviously core only records the first "layer" of parsed attrs
so we still need to parse the sub-attrs of the nested header
attribute.
v2:
- merge of patches 1 and 2 from v1
- remove stray empty lines in ops
- also remove .max_attr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
use new helper for netstats settings
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=dmWc
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-fixes-20201005' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Miscellaneous fixes
Here are some miscellaneous rxrpc fixes:
(1) Fix the xdr encoding of the contents read from an rxrpc key.
(2) Fix a BUG() for a unsupported encoding type.
(3) Fix missing _bh lock annotations.
(4) Fix acceptance handling for an incoming call where the incoming call
is encrypted.
(5) The server token keyring isn't network namespaced - it belongs to the
server, so there's no need. Namespacing it means that request_key()
fails to find it.
(6) Fix a leak of the server keyring.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Define get/set phy tunable callbacks in ethtool ops.
This will allow MAC drivers with integrated PHY still to implement
these tunables.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently skb_dump has a restriction to only dump full packet for the
first 5 socket buffers, then only headers will be printed. Remove this
arbitrary and confusing restriction, which is only documented vaguely
("up to") in the comments above the prototype.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got reports from GKE customers flows being reset by netfilter
conntrack unless nf_conntrack_tcp_be_liberal is set to 1.
Traces seemed to suggest ACK packet being dropped by the
packet capture, or more likely that ACK were received in the
wrong order.
wscale=7, SYN and SYNACK not shown here.
This ACK allows the sender to send 1871*128 bytes from seq 51359321 :
New right edge of the window -> 51359321+1871*128=51598809
09:17:23.389210 IP A > B: Flags [.], ack 51359321, win 1871, options [nop,nop,TS val 10 ecr 999], length 0
09:17:23.389212 IP B > A: Flags [.], seq 51422681:51424089, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 1408
09:17:23.389214 IP A > B: Flags [.], ack 51422681, win 1376, options [nop,nop,TS val 10 ecr 999], length 0
09:17:23.389253 IP B > A: Flags [.], seq 51424089:51488857, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 64768
09:17:23.389272 IP A > B: Flags [.], ack 51488857, win 859, options [nop,nop,TS val 10 ecr 999], length 0
09:17:23.389275 IP B > A: Flags [.], seq 51488857:51521241, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 32384
Receiver now allows to send 606*128=77568 from seq 51521241 :
New right edge of the window -> 51521241+606*128=51598809
09:17:23.389296 IP A > B: Flags [.], ack 51521241, win 606, options [nop,nop,TS val 10 ecr 999], length 0
09:17:23.389308 IP B > A: Flags [.], seq 51521241:51553625, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 32384
It seems the sender exceeds RWIN allowance, since 51611353 > 51598809
09:17:23.389346 IP B > A: Flags [.], seq 51553625:51611353, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 57728
09:17:23.389356 IP B > A: Flags [.], seq 51611353:51618393, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 7040
09:17:23.389367 IP A > B: Flags [.], ack 51611353, win 0, options [nop,nop,TS val 10 ecr 999], length 0
netfilter conntrack is not happy and sends RST
09:17:23.389389 IP A > B: Flags [R], seq 92176528, win 0, length 0
09:17:23.389488 IP B > A: Flags [R], seq 174478967, win 0, length 0
Now imagine ACK were delivered out of order and tcp_add_backlog() sets window based on wrong packet.
New right edge of the window -> 51521241+859*128=51631193
Normally TCP stack handles OOO packets just fine, but it
turns out tcp_add_backlog() does not. It can update the window
field of the aggregated packet even if the ACK sequence
of the last received packet is too old.
Many thanks to Alexandre Ferrieux for independently reporting the issue
and suggesting a fix.
Fixes: 4f693b55c3 ("tcp: implement coalescing on backlog queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Alexandre Ferrieux <alexandre.ferrieux@orange.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we skip calling tcp_cleanup_rbuf() when packets
are moved into the OoO queue or simply dropped. In both
cases we still increment tp->copied_seq, and we should
ask the TCP stack to check for ack.
Fixes: c76c695656 ("mptcp: call tcp_cleanup_rbuf on subflows")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently data fin on data packet are not handled properly:
the 'rcv_data_fin_seq' field is interpreted as the last
sequence number carrying a valid data, but for data fin
packet with valid maps we currently store map_seq + map_len,
that is, the next value.
The 'write_seq' fields carries instead the value subseguent
to the last valid byte, so in mptcp_write_data_fin() we
never detect correctly the last DSS map.
Fixes: 7279da6145 ("mptcp: Use MPTCP-level flag for sending DATA_FIN")
Fixes: 1a49b2c2a5 ("mptcp: Handle incoming 32-bit DATA_FIN values")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rcu_read_lock() is not supposed to lock the kernel_sendmsg() API
since it has the lock_sock() in qrtr_sendmsg() which will sleep. Hence,
fix it by excluding the locking for kernel_sendmsg().
While at it, let's also use radix_tree_deref_retry() to confirm the
validity of the pointer returned by radix_tree_deref_slot() and use
radix_tree_iter_resume() to resume iterating the tree properly before
releasing the lock as suggested by Doug.
Fixes: a7809ff90c ("net: qrtr: ns: Protect radix_tree_deref_slot() using rcu read locks")
Reported-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Alex Elder <elder@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Make sure SKB control block is in the proper state during IPSEC
ESP-in-TCP encapsulation. From Sabrina Dubroca.
2) Various kinds of attributes were not being cloned properly when we
build new xfrm_state objects from existing ones. Fix from Antony
Antony.
3) Make sure to keep BTF sections, from Tony Ambardar.
4) TX DMA channels need proper locking in lantiq driver, from Hauke
Mehrtens.
5) Honour route MTU during forwarding, always. From Maciej
Żenczykowski.
6) Fix races in kTLS which can result in crashes, from Rohit
Maheshwari.
7) Skip TCP DSACKs with rediculous sequence ranges, from Priyaranjan
Jha.
8) Use correct address family in xfrm state lookups, from Herbert Xu.
9) A bridge FDB flush should not clear out user managed fdb entries
with the ext_learn flag set, from Nikolay Aleksandrov.
10) Fix nested locking of netdev address lists, from Taehee Yoo.
11) Fix handling of 32-bit DATA_FIN values in mptcp, from Mat Martineau.
12) Fix r8169 data corruptions on RTL8402 chips, from Heiner Kallweit.
13) Don't free command entries in mlx5 while comp handler could still be
running, from Eran Ben Elisha.
14) Error flow of request_irq() in mlx5 is busted, due to an off by one
we try to free and IRQ never allocated. From Maor Gottlieb.
15) Fix leak when dumping netlink policies, from Johannes Berg.
16) Sendpage cannot be performed when a page is a slab page, or the page
count is < 1. Some subsystems such as nvme were doing so. Create a
"sendpage_ok()" helper and use it as needed, from Coly Li.
17) Don't leak request socket when using syncookes with mptcp, from
Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
net/core: check length before updating Ethertype in skb_mpls_{push,pop}
net: mvneta: fix double free of txq->buf
net_sched: check error pointer in tcf_dump_walker()
net: team: fix memory leak in __team_options_register
net: typhoon: Fix a typo Typoon --> Typhoon
net: hinic: fix DEVLINK build errors
net: stmmac: Modify configuration method of EEE timers
tcp: fix syn cookied MPTCP request socket leak
libceph: use sendpage_ok() in ceph_tcp_sendpage()
scsi: libiscsi: use sendpage_ok() in iscsi_tcp_segment_map()
drbd: code cleanup by using sendpage_ok() to check page for kernel_sendpage()
tcp: use sendpage_ok() to detect misused .sendpage
nvme-tcp: check page by sendpage_ok() before calling kernel_sendpage()
net: add WARN_ONCE in kernel_sendpage() for improper zero-copy send
net: introduce helper sendpage_ok() in include/linux/net.h
net: usb: pegasus: Proper error handing when setting pegasus' MAC address
net: core: document two new elements of struct net_device
netlink: fix policy dump leak
net/mlx5e: Fix race condition on nhe->n pointer in neigh update
net/mlx5e: Fix VLAN create flow
...
If someone calls setsockopt() twice to set a server key keyring, the first
keyring is leaked.
Fix it to return an error instead if the server key keyring is already set.
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
The keyring containing the server's tokens isn't network-namespaced, so it
shouldn't be looked up with a network namespace. It is expected to be
owned specifically by the server, so namespacing is unnecessary.
Fixes: a58946c158 ("keys: Pass the network namespace into request_key mechanism")
Signed-off-by: David Howells <dhowells@redhat.com>
When a new incoming call arrives at an userspace rxrpc socket on a new
connection that has a security class set, the code currently pushes it onto
the accept queue to hold a ref on it for the socket. This doesn't work,
however, as recvmsg() pops it off, notices that it's in the SERVER_SECURING
state and discards the ref. This means that the call runs out of refs too
early and the kernel oopses.
By contrast, a kernel rxrpc socket manually pre-charges the incoming call
pool with calls that already have user call IDs assigned, so they are ref'd
by the call tree on the socket.
Change the mode of operation for userspace rxrpc server sockets to work
like this too. Although this is a UAPI change, server sockets aren't
currently functional.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
conn->state_lock may be taken in softirq mode, but a previous patch
replaced an outer lock in the response-packet event handling code, and lost
the _bh from that when doing so.
Fix this by applying the _bh annotation to the state_lock locking.
Fixes: a1399f8bb0 ("rxrpc: Call channels should have separate call number spaces")
Signed-off-by: David Howells <dhowells@redhat.com>
If rxrpc_read() (which allows KEYCTL_READ to read a key), sees a token of a
type it doesn't recognise, it can BUG in a couple of places, which is
unnecessary as it can easily get back to userspace.
Fix this to print an error message instead.
Fixes: 99455153d0 ("RxRPC: Parse security index 5 keys (Kerberos 5)")
Signed-off-by: David Howells <dhowells@redhat.com>
The session key should be encoded with just the 8 data bytes and
no length; ENCODE_DATA precedes it with a 4 byte length, which
confuses some existing tools that try to parse this format.
Add an ENCODE_BYTES macro that does not include a length, and use
it for the key. Also adjust the expected length.
Note that commit 774521f353 ("rxrpc: Fix an assertion in
rxrpc_read()") had fixed a BUG by changing the length rather than
fixing the encoding. The original length was correct.
Fixes: 99455153d0 ("RxRPC: Parse security index 5 keys (Kerberos 5)")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime
Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.
So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.
Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only usage of these is to assign their address to the small_ops field
in the genl_family struct, which is a const pointer, and applying
ARRAY_SIZE() on them. Make them const to allow the compiler to put them
in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only usages of mptcp_pm_ops is to assign its address to the small_ops
field of the genl_family struct, which is a const pointer, and applying
ARRAY_SIZE() on it. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Openvswitch allows to drop a packet's Ethernet header, therefore
skb_mpls_push() and skb_mpls_pop() might be called with ethernet=true
and mac_len=0. In that case the pointer passed to skb_mod_eth_type()
doesn't point to an Ethernet header and the new Ethertype is written at
unexpected locations.
Fix this by verifying that mac_len is big enough to contain an Ethernet
header.
Fixes: fa4e0f8855 ("net/sched: fix corrupted L2 header with MPLS 'push' and 'pop' actions")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we take RTNL on dump path, it is possible to
skip RTNL on insertion path. So the following race condition
is possible:
rtnl_lock() // no rtnl lock
mutex_lock(&idrinfo->lock);
// insert ERR_PTR(-EBUSY)
mutex_unlock(&idrinfo->lock);
tc_dump_action()
rtnl_unlock()
So we have to skip those temporary -EBUSY entries on dump path
too.
Reported-and-tested-by: syzbot+b47bc4f247856fb4d9e1@syzkaller.appspotmail.com
Fixes: 0fedc63fad ("net_sched: commit action insertions together")
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow DSA drivers to make use of devlink port regions, via simple
wrappers.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow regions to be registered to a devlink port. The same netlink API
is used, but the port index is provided to indicate when a region is a
port region as opposed to a device region.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drivers want to create regions on devlink ports as well as the
devlink device instance, in order to export registers and other tables
per port. To keep all this code together in the drivers, have the
devlink ports registered early, so the setup() method can setup both
device and port devlink regions.
v3:
Remove dp->setup
Move common code out of switch statement.
Fix wrong goto
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a port is unused, still create a devlink port for it, but set the
flavour to unused. This allows us to attach devlink regions to the
port, etc.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all ports of a switch need to be used, particularly in embedded
systems. Add a port flavour for ports which physically exist in the
switch, but are not connected to the front panel etc, and so are
unused. By having unused ports present in devlink, it gives a more
accurate representation of the hardware. It also allows regions to be
associated to such ports, so allowing, for example, to determine
unused ports are correctly powered off, or to compare probable reset
defaults of unused ports to used ports experiences issues.
Actually registering unused ports and setting the flavour to unused is
optional. The DSA core will register all such switch ports, but such
ports are expected to be limited in number. Bigger ASICs may decide
not to list unused ports.
v2:
Expand the description about why it is useful
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Rename 'searched' column to 'clashres' in conntrack /proc/ stats
to amend a recent patch, from Florian Westphal.
2) Remove unused nft_data_debug(), from YueHaibing.
3) Remove unused definitions in IPVS, also from YueHaibing.
4) Fix user data memleak in tables and objects, this is also amending
a recent patch, from Jose M. Guisado.
5) Use nla_memdup() to allocate user data in table and objects, also
from Jose M. Guisado
6) User data support for chains, from Jose M. Guisado
7) Remove unused definition in nf_tables_offload, from YueHaibing.
8) Use kvzalloc() in ip_set_alloc(), from Vasily Averin.
9) Fix false positive reported by lockdep in nfnetlink mutexes,
from Florian Westphal.
10) Extend fast variant of cmp for neq operation, from Phil Sutter.
11) Implement fast bitwise variant, also from Phil Sutter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A typical use of bitwise expression is to mask out parts of an IP
address when matching on the network part only. Optimize for this common
use with a fast variant for NFT_BITWISE_BOOL-type expressions operating
on 32bit-sized values.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a boolean indicating NFT_CMP_NEQ. To include it into the match
decision, it is sufficient to XOR it with the data comparison's result.
While being at it, store the mask that is calculated during expression
init and free the eval routine from having to recalculate it each time.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
From time to time there are lockdep reports similar to this one:
WARNING: possible circular locking dependency detected
------------------------------------------------------
000000004f61aa56 (&table[i].mutex){+.+.}, at: nfnl_lock [nfnetlink]
but task is already holding lock:
[..] (&net->nft.commit_mutex){+.+.}, at: nf_tables_valid_genid [nf_tables]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&net->nft.commit_mutex){+.+.}:
[..]
nf_tables_valid_genid+0x18/0x60 [nf_tables]
nfnetlink_rcv_batch+0x24c/0x620 [nfnetlink]
nfnetlink_rcv+0x110/0x140 [nfnetlink]
netlink_unicast+0x12c/0x1e0
[..]
sys_sendmsg+0x18/0x40
linux_sparc_syscall+0x34/0x44
-> #0 (&table[i].mutex){+.+.}:
[..]
nfnl_lock+0x24/0x40 [nfnetlink]
ip_set_nfnl_get_byindex+0x19c/0x280 [ip_set]
set_match_v1_checkentry+0x14/0xc0 [xt_set]
xt_check_match+0x238/0x260 [x_tables]
__nft_match_init+0x160/0x180 [nft_compat]
[..]
sys_sendmsg+0x18/0x40
linux_sparc_syscall+0x34/0x44
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&net->nft.commit_mutex);
lock(&table[i].mutex);
lock(&net->nft.commit_mutex);
lock(&table[i].mutex);
Lockdep considers this an ABBA deadlock because the different nfnl subsys
mutexes reside in the same lockdep class, but this is a false positive.
CPU1 table[i] refers to the nftables subsys mutex, whereas CPU1 locks
the ipset subsys mutex.
Yi Che reported a similar lockdep splat, this time between ipset and
ctnetlink subsys mutexes.
Time to place them in distinct classes to avoid these warnings.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently netadmin inside non-trusted container can quickly allocate
whole node's memory via request of huge ipset hashtable.
Other ipset-related memory allocations should be restricted too.
v2: fixed typo ALLOC -> ACCOUNT
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The MPTCP ADD_ADDR suboption with echo-flag=1 has no HMAC, the size is
smaller than the one initially sent without echo-flag=1. We then need to
use the correct size everywhere when we need this echo bit.
Before this patch, the wrong size was reserved but the correct amount of
bytes were written (and read): the remaining bytes contained garbage.
Fixes: 6a6c05a8b0 ("mptcp: send out ADD_ADDR with echo flag")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/95
Reported-and-tested-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the MAC_PUSH action which pushes an MPLS LSE before the mac
header (instead of between the mac and the network headers as the
plain PUSH action does).
The only special case is when the skb has an offloaded VLAN. In that
case, it has to be inlined before pushing the MPLS header.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement TCA_VLAN_ACT_POP_ETH and TCA_VLAN_ACT_PUSH_ETH, to
respectively pop and push a base Ethernet header at the beginning of a
frame.
POP_ETH is just a matter of pulling ETH_HLEN bytes. VLAN tags, if any,
must be stripped before calling POP_ETH.
PUSH_ETH is restricted to skbs with no mac_header, and only the MAC
addresses can be configured. The Ethertype is automatically set from
skb->protocol. These restrictions ensure that all skb's fields remain
consistent, so that this action can't confuse other part of the
networking stack (like GSO).
Since openvswitch already had these actions, consolidate the code in
skbuff.c (like for vlan and mpls push/pop).
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for old hardware versions that did not have SMCDv2 support was
using suspicious pointer magic. Address the fields using an array.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building a CLC proposal message then the list of ISM devices does
not need to contain multiple devices that have the same chid value,
all these devices use the same function at the end.
Improve smc_find_ism_v2_device_clnt() to collect only ISM devices that
have unique chid values.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The retransmission refactoring patch
686989700c ("tcp: simplify tcp_mark_skb_lost")
does not properly update the total lost packet counter which may
break the policer mode in BBR. This patch fixes it.
Fixes: 686989700c ("tcp: simplify tcp_mark_skb_lost")
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smatch complains about
net/iucv/iucv.c:1119 __iucv_message_receive() warn: inconsistent indenting
While touching this line, also make the return logic consistent and thus
get rid of a goto label.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smatch complains about
net/iucv/af_iucv.c:624 iucv_sock_bind() error: memcpy() 'sa->siucv_user_id' too small (8 vs 9)
Which is absolutely correct - the memcpy() takes 9 bytes (sizeof(uid))
from an 8-byte field (sa->siucv_user_id).
Luckily the sockaddr_iucv struct contains more data after the
.siucv_user_id field, and we checked the size of the passed data earlier
on. So the memcpy() won't accidentally read from an invalid location.
Fix the warning by reducing the size of the uid variable to what's
actually needed, and thus reducing the amount of copied data.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now CTRL_CMD_GETPOLICY can only dump the family-wide
policy. Support dumping policy of a specific op.
v3:
- rebase after per-op policy export and handle that
v2:
- make cmd U32, just in case.
v1:
- don't echo op in the output in a naive way, this should
make it cleaner to extend the output format for dumping
policies for all the commands at once in the future.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20201001225933.1373426-11-kuba@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for per-op policy dumping. The data is pretty much
as before, except that now the assumption that the policy with
index 0 is "the" policy no longer holds - you now need to look
at the new CTRL_ATTR_OP_POLICY attribute which is a nested attr
(indexed by op) containing attributes for do and dump policies.
When a single op is requested, the CTRL_ATTR_OP_POLICY will be
added in the same way, since do and dump policies may differ.
v2:
- conditionally advertise per-command policies only if there
actually is a policy being used for the do/dump and it's
present at all
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll need this later for the per-op policy index dump.
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the policy dump code a bit to support adding multiple
policies to a single dump, in order to e.g. support per-op
policies in generic netlink.
v2:
- move kernel-doc to implementation [Jakub]
- squash the first patch to not flip-flop on the prototype
[Jakub]
- merge netlink_policy_dump_get_policy_idx() with the old
get_policy_idx() we already had
- rebase without Jakub's patch to have per-op dump
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maxtype is really an integral part of the policy, and while we
haven't gotten into a situation yet where this happens, it seems
that some developer might eventually have two places pointing to
identical policies, with different maxattr to exclude some attrs
in one of the places.
Even if not, it's really the right thing to compare both since the
two data items fundamentally belong together.
v2:
- also do the proper comparison in get_policy_idx()
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use in compat_syscall to import either native or the compat iovecs, and
remove the now superflous compat_import_iovec.
This removes the need for special compat logic in most callers, and
the remaining ones can still be simplified by using __import_iovec
with a bool compat parameter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In preparation for adding a new attribute to CTRL_CMD_GETPOLICY
split the policies for getpolicy and getfamily apart.
This will cause a slight user-visible change in that dumping
the policies will switch from per family to per op, but
supposedly sniffer-type applications (which are the main use
case for policy dumping thus far) should support both, anyway.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attributes are already parsed based on the policy specified
in the family and ready-to-use in info->attrs. No need to
call genlmsg_parse() again.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add policy to the struct genl_ops structure, this time
with maxattr, so it can be used properly.
Propagate .policy and .maxattr from the family
in genl_get_cmd() if needed, this way the rest of the
code does not have to worry if the policy is per op
or global.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure of ctrl_dumppolicy() is clearly split into
init and dumping. Move the init to a .start callback
for clarity, it's a more idiomatic netlink dump code structure.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever netlink dump uses more than 2 cb->args[] entries
code gets hard to read. We're about to add more state to
ctrl_dumppolicy() so create a structure.
Since the structure is typed and clearly named we can remove
the local fam_id variable and use ctx->fam_id directly.
v3:
- rebase onto explicit free fix
v1:
- s/nl_policy_dump/netlink_policy_dump_state/
- forward declare struct netlink_policy_dump_state,
and move from passing unsigned long to actual pointer type
- add build bug on
- u16 fam_id
- s/args/ctx/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bulk of the genetlink users can use smaller ops, move them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to add maxattr and policy back to genl_ops, to enable
dumping per command policy to user space. This, however, would
cause bloat for all the families with global policies. Introduce
smaller version of ops (half the size of genl_ops). Translate
these smaller ops into a full blown struct before use in the
core.
v1:
- use struct assignment
- put a full copy of the op in struct genl_dumpit_info
- s/light/small/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new devlink callback, .trap_group_action_set(), which can be used
by device drivers which do not support controlling the action (drop,
trap) on each trap but rather on the entire group trap.
If this new callback is populated, it will take precedence over the
.trap_action_set() callback when the user requests a change of all the
traps in a group.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add parser error drop packet traps, so that capable device driver could
register them with devlink. The new packet trap group holds any drops of
packets which were marked by the device as erroneous during header
parsing. Add documentation for every added packet trap and packet trap
group.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a syn-cookies request socket don't pass MPTCP-level
validation done in syn_recv_sock(), we need to release
it immediately, or it will be leaked.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/89
Fixes: 9466a1cceb ("mptcp: enable JOIN requests even if cookies are in use")
Reported-and-tested-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* lots more S1G band support
* 6 GHz scanning, finally
* kernel-doc fixes
* non-split wiphy dump fixes in nl80211
* various other small cleanups/features
-----BEGIN PGP SIGNATURE-----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=B9Xl
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of changes, this time with:
* lots more S1G band support
* 6 GHz scanning, finally
* kernel-doc fixes
* non-split wiphy dump fixes in nl80211
* various other small cleanups/features
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In libceph, ceph_tcp_sendpage() does the following checks before handle
the page by network layer's zero copy sendpage method,
if (page_count(page) >= 1 && !PageSlab(page))
This check is exactly what sendpage_ok() does. This patch replace the
open coded checks by sendpage_ok() as a code cleanup.
Signed-off-by: Coly Li <colyli@suse.de>
Acked-by: Jeff Layton <jlayton@kernel.org>
Cc: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a10674bf24 ("tcp: detecting the misuse of .sendpage for Slab
objects") adds the checks for Slab pages, but the pages don't have
page_count are still missing from the check.
Network layer's sendpage method is not designed to send page_count 0
pages neither, therefore both PageSlab() and page_count() should be
both checked for the sending page. This is exactly what sendpage_ok()
does.
This patch uses sendpage_ok() in do_tcp_sendpages() to detect misused
.sendpage, to make the code more robust.
Fixes: a10674bf24 ("tcp: detecting the misuse of .sendpage for Slab objects")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Vasily Averin <vvs@virtuozzo.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
If a page sent into kernel_sendpage() is a slab page or it doesn't have
ref_count, this page is improper to send by the zero copy sendpage()
method. Otherwise such page might be unexpected released in network code
path and causes impredictable panic due to kernel memory management data
structure corruption.
This path adds a WARN_ON() on the sending page before sends it into the
concrete zero-copy sendpage() method, if the page is improper for the
zero-copy sendpage() method, a warning message can be observed before
the consequential unpredictable kernel panic.
This patch does not change existing kernel_sendpage() behavior for the
improper page zero-copy send, it just provides hint warning message for
following potential panic due the kernel memory heap corruption.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Cong Wang <amwang@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a new helper skb_adjust_room() so users can push/pop
extra bytes from a BPF_SK_SKB_STREAM_VERDICT program.
Some protocols may include headers and other information that we may
not want to include when doing a redirect from a BPF_SK_SKB_STREAM_VERDICT
program. One use case is to redirect TLS packets into a receive socket
that doesn't expect TLS data. In TLS case the first 13B or so contain the
protocol header. With KTLS the payload is decrypted so we should be able
to redirect this to a receiving socket, but the receiving socket may not
be expecting to receive a TLS header and discard the data. Using the
above helper we can pop the header off and put an appropriate header on
the payload. This allows for creating a proxy between protocols without
extra hops through the stack or userspace.
So in order to fix this case add skb_adjust_room() so users can strip the
header. After this the user can strip the header and an unmodified receiver
thread will work correctly when data is redirected into the ingress path
of a sock.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/160160099197.7052.8443193973242831692.stgit@john-Precision-5820-Tower
Now that we are guaranteed that dsa_untag_bridge_pvid() is called after
eth_type_trans() we can utilize __vlan_find_dev_deep_rcu() which will
take care of finding an 802.1Q upper on top of a bridge master.
A common use case, prior to 12a1526d067 ("net: dsa: untag the bridge
pvid from rx skbs") was to configure a bridge 802.1Q upper like this:
ip link add name br0 type bridge vlan_filtering 0
ip link add link br0 name br0.1 type vlan id 1
in order to pop the default_pvid VLAN tag.
With this change we restore that behavior while still allowing the DSA
receive path to automatically pop the VLAN tag.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that dsa_untag_bridge_pvid() is called after eth_type_trans() we are
guaranteed that skb->protocol will be set to a correct value, thus
allowing us to avoid calling vlan_eth_hdr().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indicate to the DSA receive path that we need to untage the bridge PVID,
this allows us to remove the dsa_untag_bridge_pvid() calls from
net/dsa/tag_brcm.c.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA switch driver needs to call dsa_untag_bridge_pvid(), it can
set dsa_switch::untag_brige_pvid to indicate this is necessary.
This is a pre-requisite to making sure that we are always calling
dsa_untag_bridge_pvid() after eth_type_trans() has been called.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2020-10-02
1) Add a full xfrm compatible layer for 32-bit applications on
64-bit kernels. From Dmitry Safonov.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Upstream commit a95bc734e6 ]
If userspace doesn't complete the policy dump, we leak the
allocated state. Fix this.
Fixes: d07dcf9aad ("netlink: add infrastructure to expose policies to userspace")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If userspace doesn't complete the policy dump, we leak the
allocated state. Fix this.
Fixes: d07dcf9aad ("netlink: add infrastructure to expose policies to userspace")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 0813a84156 ("bpf: tcp: Allow bpf prog to write and parse TCP header option")
unnecessarily introduced bpf_skops_init_child() which limited the child
sk from inheriting all bpf_sock_ops_cb_flags of the listen sk. That
breaks existing user expectation.
This patch removes the bpf_skops_init_child() and just allows
sock_copy() to do its job to copy everything from listen sk to
the child sk.
Fixes: 0813a84156 ("bpf: tcp: Allow bpf prog to write and parse TCP header option")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201002013448.2542025-1-kafai@fb.com
In ieee80211_determine_chantype(), the sband->ht_cap was
being processed before S1G Operation element. Since the
HT capability element should not be present on the S1G
band, avoid processing potential garbage by moving the
call to ieee80211_apply_htcap_overrides() to after the S1G
block.
Also, in case of a missing S1G Operation element, we would
continue trying to process non-S1G elements (and return
with a channel width of 20MHz). Instead, just assume
primary channel is equal to operating and infer the
operating width from the BSS channel, then return.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20201001174748.24520-1-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When dumping wiphy information, we try to split the data into
many submessages, but for old userspace we still support the
old mode where this doesn't happen.
However, in this case we were not resetting our state correctly
and dumping multiple messages for each wiphy, which would have
broken such older userspace.
This was broken pretty much immediately afterwards because it
only worked in the original commit where non-split dumps didn't
have any more data than split dumps...
Fixes: fe1abafd94 ("nl80211: re-add channel width and extended capa advertising")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200928130717.3e6d9c6bada2.Ie0f151a8d0d00a8e1e18f6a8c9244dd02496af67@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When wiphy dumps cannot be split, such as in events or with
older userspace that doesn't support it, the size can today
be too big.
Reduce it, by doing two things:
1) remove data that couldn't have been present before the
split capability was introduced since it's new, such as
HE capabilities
2) as suggested by Martin Willi, remove management frame
subtypes from the split dumps, as just (1) isn't even
enough due to other new code capabilities. This is fine
as old consumers (really just wpa_supplicant) didn't
check this data before they got support for split dumps.
Reported-by: Martin Willi <martin@strongswan.org>
Suggested-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Martin Willi <martin@strongswan.org>
Link: https://lore.kernel.org/r/20200928130655.53bce7873164.I71f06c9a221cd0630429a1a56eeae68a13beca61@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix follow warnings:
[net/core/net-sysfs.c:1161]: (warning) %u in format string (no. 1)
requires 'unsigned int' but the argument type is 'int'.
[net/core/net-sysfs.c:1162]: (warning) %u in format string (no. 1)
requires 'unsigned int' but the argument type is 'int'.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix follow warnings:
[net/core/pktgen.c:925]: (warning) %u in format string (no. 1)
requires 'unsigned int' but the argument type is 'signed int'.
[net/core/pktgen.c:942]: (warning) %u in format string (no. 1)
requires 'unsigned int' but the argument type is 'signed int'.
[net/core/pktgen.c:962]: (warning) %u in format string (no. 1)
requires 'unsigned int' but the argument type is 'signed int'.
[net/core/pktgen.c:984]: (warning) %u in format string (no. 1)
requires 'unsigned int' but the argument type is 'signed int'.
[net/core/pktgen.c:1149]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-10-01
The following pull-request contains BPF updates for your *net-next* tree.
We've added 90 non-merge commits during the last 8 day(s) which contain
a total of 103 files changed, 7662 insertions(+), 1894 deletions(-).
Note that once bpf(/net) tree gets merged into net-next, there will be a small
merge conflict in tools/lib/bpf/btf.c between commit 1245008122 ("libbpf: Fix
native endian assumption when parsing BTF") from the bpf tree and the commit
3289959b97 ("libbpf: Support BTF loading and raw data output in both endianness")
from the bpf-next tree. Correct resolution would be to stick with bpf-next, it
should look like:
[...]
/* check BTF magic */
if (fread(&magic, 1, sizeof(magic), f) < sizeof(magic)) {
err = -EIO;
goto err_out;
}
if (magic != BTF_MAGIC && magic != bswap_16(BTF_MAGIC)) {
/* definitely not a raw BTF */
err = -EPROTO;
goto err_out;
}
/* get file size */
[...]
The main changes are:
1) Add bpf_snprintf_btf() and bpf_seq_printf_btf() helpers to support displaying
BTF-based kernel data structures out of BPF programs, from Alan Maguire.
2) Speed up RCU tasks trace grace periods by a factor of 50 & fix a few race
conditions exposed by it. It was discussed to take these via BPF and
networking tree to get better testing exposure, from Paul E. McKenney.
3) Support multi-attach for freplace programs, needed for incremental attachment
of multiple XDP progs using libxdp dispatcher model, from Toke Høiland-Jørgensen.
4) libbpf support for appending new BTF types at the end of BTF object, allowing
intrusive changes of prog's BTF (useful for future linking), from Andrii Nakryiko.
5) Several BPF helper improvements e.g. avoid atomic op in cookie generator and add
a redirect helper into neighboring subsys, from Daniel Borkmann.
6) Allow map updates on sockmaps from bpf_iter context in order to migrate sockmaps
from one to another, from Lorenz Bauer.
7) Fix 32 bit to 64 bit assignment from latest alu32 bounds tracking which caused
a verifier issue due to type downgrade to scalar, from John Fastabend.
8) Follow-up on tail-call support in BPF subprogs which optimizes x64 JIT prologue
and epilogue sections, from Maciej Fijalkowski.
9) Add an option to perf RB map to improve sharing of event entries by avoiding remove-
on-close behavior. Also, add BPF_PROG_TEST_RUN for raw_tracepoint, from Song Liu.
10) Fix a crash in AF_XDP's socket_release when memory allocation for UMEMs fails,
from Magnus Karlsson.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal reported a build failure likes below:
BTFIDS vmlinux
FAILED unresolved symbol tcp_timewait_sock
make[1]: *** [/.../linux-5.9-rc7/Makefile:1176: vmlinux] Error 255
This error can be triggered when config has CONFIG_NET enabled
but CONFIG_INET disabled. In this case, there is no user of
istructs inet_timewait_sock and tcp_timewait_sock and hence
vmlinux BTF types are not generated for these two structures.
To fix the problem, let us force BTF generation for these two
structures with BTF_TYPE_EMIT.
Fixes: fce557bcef ("bpf: Make btf_sock_ids global")
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20201001051339.2549085-1-yhs@fb.com
Now we have a io_uring kernel header, move this definition out of fs.h
and into io_uring.h where it belongs.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Previously, devlink called into drop monitor in order to report hardware
originated drops / exceptions. devlink intentionally filtered control
packets and did not pass them to drop monitor as they were not dropped
by the underlying hardware.
Now drop monitor registers its probe on a generic 'devlink_trap_report'
tracepoint and should therefore perform this filtering itself instead of
having devlink do that.
Add the trap type as metadata and have drop monitor ignore control
packets.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'struct net_dm_hw_metadata' is a duplicate of 'struct
devlink_trap_metadata'.
Remove the former and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old probe functions that were invoked by drop monitor code are no
longer called and can thus be removed. They were replaced by actual
probe functions that are registered on the recently introduced
'devlink_trap_report' tracepoint.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert drop monitor to use the recently introduced
'devlink_trap_report' tracepoint instead of having devlink call into
drop monitor.
This is both consistent with software originated drops ('kfree_skb'
tracepoint) and also allows drop monitor to be built as a module and
still report hardware originated drops.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop monitor supports two alerting modes: Summary and packet. Prepare a
probe function for each, so that they could be later registered on the
devlink tracepoint by calling register_trace_devlink_trap_report(),
based on the configured alerting mode.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a tracepoint for trap reports so that drop monitor could register
its probe on it. Use trace_devlink_trap_report_enabled() to avoid
wasting cycles setting the trap metadata if the tracepoint is not
enabled.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever host is under very high memory pressure,
__tcp_send_ack() skb allocation fails, and we setup
a 200 ms (TCP_DELACK_MAX) timer before retrying.
On hosts with high number of TCP sockets, we can spend
considerable amount of cpu cycles in these attempts,
add high pressure on various spinlocks in mm-layer,
ultimately blocking threads attempting to free space
from making any progress.
This patch adds standard exponential backoff to avoid
adding fuel to the fire.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP has been using it to work around the possibility of tcp_delack_timer()
finding the socket owned by user.
After commit 6f458dfb40 ("tcp: improve latencies of timer triggered events")
we added TCP_DELACK_TIMER_DEFERRED atomic bit for more immediate recovery,
so we can get rid of icsk_ack.blocked
This frees space that following patch will reuse.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a redirect_neigh() helper as redirect() drop-in replacement
for the xmit side. Main idea for the helper is to be very similar
in semantics to the latter just that the skb gets injected into
the neighboring subsystem in order to let the stack do the work
it knows best anyway to populate the L2 addresses of the packet
and then hand over to dev_queue_xmit() as redirect() does.
This solves two bigger items: i) skbs don't need to go up to the
stack on the host facing veth ingress side for traffic egressing
the container to achieve the same for populating L2 which also
has the huge advantage that ii) the skb->sk won't get orphaned in
ip_rcv_core() when entering the IP routing layer on the host stack.
Given that skb->sk neither gets orphaned when crossing the netns
as per 9c4c325252 ("skbuff: preserve sock reference when scrubbing
the skb.") the helper can then push the skbs directly to the phys
device where FQ scheduler can do its work and TCP stack gets proper
backpressure given we hold on to skb->sk as long as skb is still
residing in queues.
With the helper used in BPF data path to then push the skb to the
phys device, I observed a stable/consistent TCP_STREAM improvement
on veth devices for traffic going container -> host -> host ->
container from ~10Gbps to ~15Gbps for a single stream in my test
environment.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Cc: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/bpf/f207de81629e1724899b73b8112e0013be782d35.1601477936.git.daniel@iogearbox.net
With its use in BPF, the cookie generator can be called very frequently
in particular when used out of cgroup v2 hooks (e.g. connect / sendmsg)
and attached to the root cgroup, for example, when used in v1/v2 mixed
environments. In particular, when there's a high churn on sockets in the
system there can be many parallel requests to the bpf_get_socket_cookie()
and bpf_get_netns_cookie() helpers which then cause contention on the
atomic counter.
As similarly done in f991bd2e14 ("fs: introduce a per-cpu last_ino
allocator"), add a small helper library that both can use for the 64 bit
counters. Given this can be called from different contexts, we also need
to deal with potential nested calls even though in practice they are
considered extremely rare. One idea as suggested by Eric Dumazet was
to use a reverse counter for this situation since we don't expect 64 bit
overflows anyways; that way, we can avoid bigger gaps in the 64 bit
counter space compared to just batch-wise increase. Even on machines
with small number of cores (e.g. 4) the cookie generation shrinks from
min/max/med/avg (ns) of 22/50/40/38.9 down to 10/35/14/17.3 when run
in parallel from multiple CPUs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Link: https://lore.kernel.org/bpf/8a80b8d27d3c49f9a14e1d5213c19d8be87d1dc8.1601477936.git.daniel@iogearbox.net
Similarly to 5a52ae4e32 ("bpf: Allow to retrieve cgroup v1 classid
from v2 hooks"), add a helper to retrieve cgroup v1 classid solely
based on the skb->sk, so it can be used as key as part of BPF map
lookups out of tc from host ns, in particular given the skb->sk is
retained these days when crossing net ns thanks to 9c4c325252
("skbuff: preserve sock reference when scrubbing the skb."). This
is similar to bpf_skb_cgroup_id() which implements the same for v2.
Kubernetes ecosystem is still operating on v1 however, hence net_cls
needs to be used there until this can be dropped in with the v2
helper of bpf_skb_cgroup_id().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/ed633cf27a1c620e901c5aa99ebdefb028dce600.1601477936.git.daniel@iogearbox.net
Enables storing userdata for nft_chain. Field udata points to user data
and udlen stores its length.
Adds new attribute flag NFTA_CHAIN_USERDATA.
Signed-off-by: Jose M. Guisado Gomez <guigom@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When userdata support was added to tables and objects, user data coming
from user space was allocated and copied using kzalloc + nla_memcpy.
Use nla_memdup to copy userdata of tables and objects.
Signed-off-by: Jose M. Guisado Gomez <guigom@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When userdata was introduced for tables and objects its allocation was
only freed inside the error path of the new{table, object} functions.
Free user data inside corresponding destroy functions for tables and
objects.
Fixes: b131c96496 ("netfilter: nf_tables: add userdata support for nft_object")
Fixes: 7a81575b80 ("netfilter: nf_tables: add userdata attributes to nft_table")
Signed-off-by: Jose M. Guisado Gomez <guigom@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Alexei Starovoitov says:
====================
pull-request: bpf 2020-09-29
The following pull-request contains BPF updates for your *net* tree.
We've added 7 non-merge commits during the last 14 day(s) which contain
a total of 7 files changed, 28 insertions(+), 8 deletions(-).
The main changes are:
1) fix xdp loading regression in libbpf for old kernels, from Andrii.
2) Do not discard packet when NETDEV_TX_BUSY, from Magnus.
3) Fix corner cases in libbpf related to endianness and kconfig, from Tony.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The peer may send a DATA_FIN mapping with either a 32-bit or 64-bit
sequence number. When a 32-bit sequence number is received for the
DATA_FIN, it must be expanded to 64 bits before comparing it to the
last acked sequence number. This expansion was missing.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/93
Fixes: 3721b9b646 ("mptcp: Track received DATA_FIN sequence number and add related helpers")
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The msk->ack_seq value is sometimes read without the msk lock held, so
make proper use of READ_ONCE and WRITE_ONCE.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quite some drivers make conditional decisions based on in_interrupt() to
invoke either netif_rx() or netif_rx_ni().
Conditionals based on in_interrupt() or other variants of preempt count
checks in drivers should not exist for various reasons and Linus clearly
requested to either split the code pathes or pass an argument to the
common functions which provides the context.
This is obviously the correct solution, but for some of the affected
drivers this needs a major rewrite due to their convoluted structure.
As in_interrupt() usage in drivers needs to be phased out, provide
netif_rx_any_context() as a stop gap for these drivers.
This confines the in_interrupt() conditional to core code which in turn
allows to remove the access to this check for driver code and provides one
central place to do further modifications once the driver maze is cleaned
up.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an L2TPv3 session receives a data frame with an incorrect cookie
l2tp_core logs a warning message and bumps a stats counter to reflect
the fact that the packet has been dropped.
However, the stats counter in question is missing from the l2tp_netlink
get message for tunnel and session instances.
Include the statistic in the netlink get response.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-09-29
Here's the main bluetooth-next pull request for 5.10:
- Multiple fixes to suspend/resume handling
- Added mgmt events for controller suspend/resume state
- Improved extended advertising support
- btintel: Enhanced support for next generation controllers
- Added Qualcomm Bluetooth SoC WCN6855 support
- Several other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After 'peeking' the ring, the consumer, not the producer, reads the data.
Fix this mistake in the comments.
Fixes: 15d8c9162c ("xsk: Add function naming comments and reorder functions")
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20200928082344.17110-1-ciara.loftus@intel.com
Like all genl families ethtool_genl_family needs to not
be a straight up constant, because it's modified/initialized
by genl_register_family(). After init, however, it's only
passed to genlmsg_put() & co. therefore we can mark it
as __ro_after_init.
Since genl_family structure contains function pointers
mark this as a fix.
Fixes: 2b4a8990b7 ("ethtool: introduce ethtool netlink interface")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Refactor the code according to the use of a flexible-array member in
struct tc_u_hnode and use the struct_size() helper to calculate the
size for the allocations. Commit 5778d39d07 ("net_sched: fix struct
tc_u_hnode layout in u32") makes it clear that the code is expected to
dynamically allocate divisor + 1 entries for ->ht[] in tc_uhnode. Also,
based on other observations, as the piece of code below:
1232 for (h = 0; h <= ht->divisor; h++) {
1233 for (n = rtnl_dereference(ht->ht[h]);
1234 n;
1235 n = rtnl_dereference(n->next)) {
1236 if (tc_skip_hw(n->flags))
1237 continue;
1238
1239 err = u32_reoffload_knode(tp, n, add, cb,
1240 cb_priv, extack);
1241 if (err)
1242 return err;
1243 }
1244 }
we can assume that, in general, the code is actually expecting to allocate
that extra space for the one-element array in tc_uhnode, everytime it
allocates memory for instances of tc_uhnode or tc_u_common structures.
That's the reason for passing '1' as the last argument for struct_size()
in the allocation for _root_ht_ and _tp_c_, and 'divisor + 1' in the
allocation code for _ht_.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9-rc1/process/deprecated.html#zero-length-and-one-element-arrays
Tested-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/5f7062af.z3T9tn9yIPv6h5Ny%25lkp@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow passing a pointer to a BTF struct sock_common* when updating
a sockmap or sockhash. Since BTF pointers can fault and therefore be
NULL at runtime we need to add an additional !sk check to
sock_map_update_elem. Since we may be passed a request or timewait
socket we also need to check sk_fullsock. Doing this allows calling
map_update_elem on sockmap from bpf_iter context, which uses
BTF pointers.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200928090805.23343-2-lmb@cloudflare.com
similarly to what has been done with commit 9d149045b3 ("geneve: change
from tx_error to tx_dropped on missing metadata"), avoid reporting errors
to userspace in case the kernel doesn't find any tunnel information for a
skb that is going to be transmitted: an increase of tx_dropped is enough.
tested with the following script:
# for t in ip6gre ip6gretap ip6erspan; do
> ip link add dev gre6-test0 type $t external
> ip address add dev gre6-test0 2001:db8::1/64
> ip link set dev gre6-test0 up
> sleep 30
> ip -s -j link show dev gre6-test0 | jq \
> '.[0].stats64.tx | {"errors": .errors, "dropped": .dropped}'
> ip link del dev gre6-test0
> done
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch covers the small SMCD version 2 changes for CLC decline.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC Version 2 defines a first contact extension for CLC accept
and CLC confirm. This patch covers sending and receiving of the
CLC first contact extension.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new format of SMCD V2 CLC accept and confirm is introduced,
and building and checking of SMCD V2 CLC accepts / confirms is adapted
accordingly.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD Version 2 allows to propose up to 8 additional ISM devices
offered to the peer as candidates for SMCD communication.
This patch covers the server side, i.e. selection of an ISM device
matching one of the proposed ISM devices, that will be used for
CLC accept
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new format of an SMCD V2 CLC proposal is introduced, and
building and checking of SMCD V2 CLC proposals is adapted
accordingly.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD Version 2 allows to propose up to 8 additional ISM devices
offered to the peer as candidates for SMCD communication.
This patch covers determination of the ISM devices to be proposed.
ISM devices without PNETID are preferred, since ISM devices with
PNETID are a V1 leftover and will disappear over the time.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD version 2 allows usage of ISM devices with hardware PNETID
only, if an Ethernet net_device exists with the same hardware PNETID.
This requires to maintain a list of pnetids belonging to
Ethernet net_devices, which is covered by this patch.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With SMCD version 2 the CHIDs of ISM devices are needed for the
CLC handshake.
This patch provides the new callback to retrieve the CHID of an
ISM device.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD version 2 defines a System Enterprise ID (short SEID).
This patch contains the SEID creation and adds the callback to
retrieve the created SEID.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD Version 2 allows proposing of up to 8 ISM devices in addition
to the native ISM device of SMCD Version 1.
This patch prepares the struct smc_init_info to deal with these
additional 8 ISM devices.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending CLC confirm and CLC accept, separate the trailing
part of the message from the initial part (to be prepared for
future first contact extension).
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides better separation of device determinations
in function smc_listen_work(). No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD version 2 defines 2 more bits in the CLC header to specify
version 2 types. This patch prepares better naming of the CLC
header fields. No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the existing symbol _S instead of SMC_ASCII_BLANK, and introduce a
helper to check if a pnetid is set. No functional change.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add a new variable 'nested_level' into the net_device
structure.
This variable will be used as a parameter of spin_lock_nested() of
dev->addr_list_lock.
netif_addr_lock() can be called recursively so spin_lock_nested() is
used instead of spin_lock() and dev->lower_level is used as a parameter
of spin_lock_nested().
But, dev->lower_level value can be updated while it is being used.
So, lockdep would warn a possible deadlock scenario.
When a stacked interface is deleted, netif_{uc | mc}_sync() is
called recursively.
So, spin_lock_nested() is called recursively too.
At this moment, the dev->lower_level variable is used as a parameter of it.
dev->lower_level value is updated when interfaces are being unlinked/linked
immediately.
Thus, After unlinking, dev->lower_level shouldn't be a parameter of
spin_lock_nested().
A (macvlan)
|
B (vlan)
|
C (bridge)
|
D (macvlan)
|
E (vlan)
|
F (bridge)
A->lower_level : 6
B->lower_level : 5
C->lower_level : 4
D->lower_level : 3
E->lower_level : 2
F->lower_level : 1
When an interface 'A' is removed, it releases resources.
At this moment, netif_addr_lock() would be called.
Then, netdev_upper_dev_unlink() is called recursively.
Then dev->lower_level is updated.
There is no problem.
But, when the bridge module is removed, 'C' and 'F' interfaces
are removed at once.
If 'F' is removed first, a lower_level value is like below.
A->lower_level : 5
B->lower_level : 4
C->lower_level : 3
D->lower_level : 2
E->lower_level : 1
F->lower_level : 1
Then, 'C' is removed. at this moment, netif_addr_lock() is called
recursively.
The ordering is like this.
C(3)->D(2)->E(1)->F(1)
At this moment, the lower_level value of 'E' and 'F' are the same.
So, lockdep warns a possible deadlock scenario.
In order to avoid this problem, a new variable 'nested_level' is added.
This value is the same as dev->lower_level - 1.
But this value is updated in rtnl_unlock().
So, this variable can be used as a parameter of spin_lock_nested() safely
in the rtnl context.
Test commands:
ip link add br0 type bridge vlan_filtering 1
ip link add vlan1 link br0 type vlan id 10
ip link add macvlan2 link vlan1 type macvlan
ip link add br3 type bridge vlan_filtering 1
ip link set macvlan2 master br3
ip link add vlan4 link br3 type vlan id 10
ip link add macvlan5 link vlan4 type macvlan
ip link add br6 type bridge vlan_filtering 1
ip link set macvlan5 master br6
ip link add vlan7 link br6 type vlan id 10
ip link add macvlan8 link vlan7 type macvlan
ip link set br0 up
ip link set vlan1 up
ip link set macvlan2 up
ip link set br3 up
ip link set vlan4 up
ip link set macvlan5 up
ip link set br6 up
ip link set vlan7 up
ip link set macvlan8 up
modprobe -rv bridge
Splat looks like:
[ 36.057436][ T744] WARNING: possible recursive locking detected
[ 36.058848][ T744] 5.9.0-rc6+ #728 Not tainted
[ 36.059959][ T744] --------------------------------------------
[ 36.061391][ T744] ip/744 is trying to acquire lock:
[ 36.062590][ T744] ffff8c4767509280 (&vlan_netdev_addr_lock_key){+...}-{2:2}, at: dev_set_rx_mode+0x19/0x30
[ 36.064922][ T744]
[ 36.064922][ T744] but task is already holding lock:
[ 36.066626][ T744] ffff8c4767769280 (&vlan_netdev_addr_lock_key){+...}-{2:2}, at: dev_uc_add+0x1e/0x60
[ 36.068851][ T744]
[ 36.068851][ T744] other info that might help us debug this:
[ 36.070731][ T744] Possible unsafe locking scenario:
[ 36.070731][ T744]
[ 36.072497][ T744] CPU0
[ 36.073238][ T744] ----
[ 36.074007][ T744] lock(&vlan_netdev_addr_lock_key);
[ 36.075290][ T744] lock(&vlan_netdev_addr_lock_key);
[ 36.076590][ T744]
[ 36.076590][ T744] *** DEADLOCK ***
[ 36.076590][ T744]
[ 36.078515][ T744] May be due to missing lock nesting notation
[ 36.078515][ T744]
[ 36.080491][ T744] 3 locks held by ip/744:
[ 36.081471][ T744] #0: ffffffff98571df0 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x236/0x490
[ 36.083614][ T744] #1: ffff8c4767769280 (&vlan_netdev_addr_lock_key){+...}-{2:2}, at: dev_uc_add+0x1e/0x60
[ 36.085942][ T744] #2: ffff8c476c8da280 (&bridge_netdev_addr_lock_key/4){+...}-{2:2}, at: dev_uc_sync+0x39/0x80
[ 36.088400][ T744]
[ 36.088400][ T744] stack backtrace:
[ 36.089772][ T744] CPU: 6 PID: 744 Comm: ip Not tainted 5.9.0-rc6+ #728
[ 36.091364][ T744] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[ 36.093630][ T744] Call Trace:
[ 36.094416][ T744] dump_stack+0x77/0x9b
[ 36.095385][ T744] __lock_acquire+0xbc3/0x1f40
[ 36.096522][ T744] lock_acquire+0xb4/0x3b0
[ 36.097540][ T744] ? dev_set_rx_mode+0x19/0x30
[ 36.098657][ T744] ? rtmsg_ifinfo+0x1f/0x30
[ 36.099711][ T744] ? __dev_notify_flags+0xa5/0xf0
[ 36.100874][ T744] ? rtnl_is_locked+0x11/0x20
[ 36.101967][ T744] ? __dev_set_promiscuity+0x7b/0x1a0
[ 36.103230][ T744] _raw_spin_lock_bh+0x38/0x70
[ 36.104348][ T744] ? dev_set_rx_mode+0x19/0x30
[ 36.105461][ T744] dev_set_rx_mode+0x19/0x30
[ 36.106532][ T744] dev_set_promiscuity+0x36/0x50
[ 36.107692][ T744] __dev_set_promiscuity+0x123/0x1a0
[ 36.108929][ T744] dev_set_promiscuity+0x1e/0x50
[ 36.110093][ T744] br_port_set_promisc+0x1f/0x40 [bridge]
[ 36.111415][ T744] br_manage_promisc+0x8b/0xe0 [bridge]
[ 36.112728][ T744] __dev_set_promiscuity+0x123/0x1a0
[ 36.113967][ T744] ? __hw_addr_sync_one+0x23/0x50
[ 36.115135][ T744] __dev_set_rx_mode+0x68/0x90
[ 36.116249][ T744] dev_uc_sync+0x70/0x80
[ 36.117244][ T744] dev_uc_add+0x50/0x60
[ 36.118223][ T744] macvlan_open+0x18e/0x1f0 [macvlan]
[ 36.119470][ T744] __dev_open+0xd6/0x170
[ 36.120470][ T744] __dev_change_flags+0x181/0x1d0
[ 36.121644][ T744] dev_change_flags+0x23/0x60
[ 36.122741][ T744] do_setlink+0x30a/0x11e0
[ 36.123778][ T744] ? __lock_acquire+0x92c/0x1f40
[ 36.124929][ T744] ? __nla_validate_parse.part.6+0x45/0x8e0
[ 36.126309][ T744] ? __lock_acquire+0x92c/0x1f40
[ 36.127457][ T744] __rtnl_newlink+0x546/0x8e0
[ 36.128560][ T744] ? lock_acquire+0xb4/0x3b0
[ 36.129623][ T744] ? deactivate_slab.isra.85+0x6a1/0x850
[ 36.130946][ T744] ? __lock_acquire+0x92c/0x1f40
[ 36.132102][ T744] ? lock_acquire+0xb4/0x3b0
[ 36.133176][ T744] ? is_bpf_text_address+0x5/0xe0
[ 36.134364][ T744] ? rtnl_newlink+0x2e/0x70
[ 36.135445][ T744] ? rcu_read_lock_sched_held+0x32/0x60
[ 36.136771][ T744] ? kmem_cache_alloc_trace+0x2d8/0x380
[ 36.138070][ T744] ? rtnl_newlink+0x2e/0x70
[ 36.139164][ T744] rtnl_newlink+0x47/0x70
[ ... ]
Fixes: 845e0ebb44 ("net: change addr_list_lock back to static key")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions related to nested interface infrastructure such as
netdev_walk_all_{ upper | lower }_dev() pass both private functions
and "data" pointer to handle their own things.
At this point, the data pointer type is void *.
In order to make it easier to expand common variables and functions,
this new netdev_nested_priv structure is added.
In the following patch, a new member variable will be added into this
struct to fix the lockdep issue.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdev_upper_dev_unlink() has to work differently according to flags.
This idea is the same with __netdev_upper_dev_link().
In the following patches, new flags will be added.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All TC actions call tcf_action_check_ctrlact() to validate
goto chain, so this check in tcf_action_init_1() is actually
redundant. Remove it to save troubles of leaking memory.
Fixes: e49d8c22f1 ("net_sched: defer tcf_idr_insert() in tcf_action_init_1()")
Reported-by: Vlad Buslov <vladbu@mellanox.com>
Suggested-by: Davide Caratti <dcaratti@redhat.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add .test_run for raw_tracepoint. Also, introduce a new feature that runs
the target program on a specific CPU. This is achieved by a new flag in
bpf_attr.test, BPF_F_TEST_RUN_ON_CPU. When this flag is set, the program
is triggered on cpu with id bpf_attr.test.cpu. This feature is needed for
BPF programs that handle perf_event and other percpu resources, as the
program can access these resource locally.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200925205432.1777-2-songliubraving@fb.com
Unfortunately recent Intel NIC designs share the UDP port table
across netdevs. So far the UDP tunnel port state was maintained
per netdev, we need to extend that to cater to Intel NICs.
Expect NICs to allocate the info structure dynamically and link
to the state from there. All the shared NICs will record port
offload information in the one instance of the table so we need
to make sure that the use count can accommodate larger numbers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a user-space software manages fdb entries externally it should
set the ext_learn flag which marks the fdb entry as externally managed
and avoids expiring it (they're treated as static fdbs). Unfortunately
on events where fdb entries are flushed (STP down, netlink fdb flush
etc) these fdbs are also deleted automatically by the bridge. That in turn
causes trouble for the managing user-space software (e.g. in MLAG setups
we lose remote fdb entries on port flaps).
These entries are completely externally managed so we should avoid
automatically deleting them, the only exception are offloaded entries
(i.e. BR_FDB_ADDED_BY_EXT_LEARN + BR_FDB_OFFLOADED). They are flushed as
before.
Fixes: eb100e0e24 ("net: bridge: allow to add externally learned entries from user-space")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2020-09-28
1) Fix a build warning in ip_vti if CONFIG_IPV6 is not set.
From YueHaibing.
2) Restore IPCB on espintcp before handing the packet to xfrm
as the information there is still needed.
From Sabrina Dubroca.
3) Fix pmtu updating for xfrm interfaces.
From Sabrina Dubroca.
4) Some xfrm state information was not cloned with xfrm_do_migrate.
Fixes to clone the full xfrm state, from Antony Antony.
5) Use the correct address family in xfrm_state_find. The struct
flowi must always be interpreted along with the original
address family. This got lost over the years.
Fix from Herbert Xu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix possible crash in socket_release when an out-of-memory error has
occurred in the bind call. If a socket using the XDP_SHARED_UMEM flag
encountered an error in xp_create_and_assign_umem, the bind code
jumped to the exit routine but erroneously forgot to set the err value
before jumping. This meant that the exit routine thought the setup
went well and set the state of the socket to XSK_BOUND. The xsk socket
release code will then, at application exit, think that this is a
properly setup socket, when it is not, leading to a crash when all
fields in the socket have in fact not been initialized properly. Fix
this by setting the err variable in xsk_bind so that the socket is not
set to XSK_BOUND which leads to the clean-up in xsk_release not being
triggered.
Fixes: 1c1efc2af1 ("xsk: Create and free buffer pool independently from umem")
Reported-by: syzbot+ddc7b4944bc61da19b81@syzkaller.appspotmail.com
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/1601112373-10595-1-git-send-email-magnus.karlsson@gmail.com
Allow drivers to request that interface-iterator does NOT iterate
over interfaces that are not sdata-in-driver. This will allow
us to fix crashes in ath10k (and possibly other drivers).
To summarize Johannes' explanation:
Consider
add interface wlan0
add interface wlan1
iterate active interfaces -> wlan0 wlan1
add interface wlan2
iterate active interfaces -> wlan0 wlan1 wlan2
If you apply this scenario to a restart, which ought to be functionally
equivalent to the normal startup, just compressed in time, you're
basically saying that today you get
add interface wlan0
add interface wlan1
iterate active interfaces -> wlan0 wlan1 wlan2 << problem here
add interface wlan2
iterate active interfaces -> wlan0 wlan1 wlan2
which yeah, totally seems wrong.
But fixing that to be
add interface wlan0
add interface wlan1
iterate active interfaces ->
<nothing>
add interface wlan2
iterate active interfaces -> <nothing>
(or
maybe -> wlan0 wlan1 wlan2 if the reconfig already completed)
This is also at least somewhat wrong, but better to not iterate
over something that exists in the driver than iterate over something
that does not. Originally the first issue was causing crashes in
testing with lots of station vdevs on an ath10k radio, combined
with firmware crashing.
I ran with a similar patch for years with no obvious bad results,
including significant testing with ath9k and ath10k.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20200922191957.25257-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The SRG min and max offset won't present when SRG Information Present of
SR control field of Spatial Reuse Parameter Set element set to 0. Per
spec. IEEE802.11ax D7.0, SRG OBSS PD Min Offset ≤ SRG OBSS PD Max
Offset. Hence fix the constrain check to allow same values in both
offset and also call appropriate nla_get function to read the values.
Fixes: 796e90f42b ("cfg80211: add support for parsing OBBS_PD attributes")
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Link: https://lore.kernel.org/r/1601278091-20313-1-git-send-email-rmanohar@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The the __freq_reg_info() never returns NULL and the callers don't check
for NULL. This initialization to set "reg_rule = NULL;" is just there
to make GCC happy but it's not required in current GCCs.
The problem is that Smatch sees the initialization and concludes that
this function can return NULL so it complains that the callers are not
checking for it.
Smatch used to be able to parse this correctly but we recently changed
the code from:
- for (bw = MHZ_TO_KHZ(20); bw >= min_bw; bw = bw / 2) {
+ for (bw = MHZ_TO_KHZ(bws[i]); bw >= min_bw; bw = MHZ_TO_KHZ(bws[i--])) {
Originally Smatch used to understand that this code always iterates
through the loop once, but the change from "MHZ_TO_KHZ(20)" to
"MHZ_TO_KHZ(bws[i])" is too complicated for Smatch.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200923084203.GC1454948@mwanda
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a frame was acked and probe frames were sent, the connection monitoring
needs to be reset, otherwise it will keep probing until the connection is
considered dead, even though frames have been acked in the mean time.
Fixes: 9abf4e4983 ("mac80211: optimize station connection monitor")
Reported-by: Georgi Valkov <gvalkov@abv.bg>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200927105605.97954-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Recently channels gained a potential frequency offset, so
include this in the per-channel survey info.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-16-thomas@adapt-ip.com
[add the offset only if non-zero]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The changes required for associating in S1G are:
- apply S1G BSS channel info before assoc
- mark all S1G STAs as QoS STAs
- include and parse AID request element
- handle new Association Response format
- don't fail assoc if supported rates element is missing
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-15-thomas@adapt-ip.com
[pass skb to ieee80211_add_aid_request_ie(), remove unused variable 'bss']
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G beacons are 802.11 Extension Frames, so the fixed
header part differs from regular beacons.
Add a handler to process S1G beacons and abstract out the
fetching of BSSID and element start locations in the
beacon body handler.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-14-thomas@adapt-ip.com
[don't rename, small coding style cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
minstrel_ht is confused by the lack of sband->bitrates,
and S1G will likely require a unique RC algorithm, so
avoid rate init for now if STA is on the S1G band.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-13-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G doesn't have legacy (sband->bitrates) rates, only MCS.
For now, just send a frame at MCS 0 if a low rate is
requested. Note we also redefine (since we're out of TX
flags) TX_RC_VHT_MCS as TX_RC_S1G_MCS to indicate an S1G
MCS. This is probably OK as VHT MCS is not valid on S1G
band and vice versa.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-12-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For now just skip the duration calculation for frames
transmitted on the S1G band and avoid a warning.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-11-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G allows listen interval up to 2^14 * 10000 beacon
intervals. In order to do this listen interval needs a
scaling factor applied to the lower 14 bits. Calculate
this and properly encode the listen interval for S1G STAs.
See IEEE802.11ah-2016 Table 9-44a for reference.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-10-thomas@adapt-ip.com
[move listen_int_usf into function using it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The sending STA type is implicit based on beacon or probe
response content. If sending STA was an S1G STA, adjust
the Information Element location accordingly.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-9-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit finds the correct offset for Information
Elements in S1G beacon frames so they can be reported in
scan results.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-8-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The S1G beacon is an extension frame as opposed to
management frame for the regular beacon. This means we may
have to occasionally cast the frame buffer to a different
header type. Luckily this isn't too bad as scan results
mostly only care about the IEs.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-6-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Include the S1G Capabilities element in an association
request, and support the cfg80211 capability overrides.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-5-thomas@adapt-ip.com
[pass skb to ieee80211_add_s1g_capab_ie(), small code style edits]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NL80211_ATTR_S1G_CAPABILITY can be passed along with
NL80211_ATTR_S1G_CAPABILITY_MASK to NL80211_CMD_ASSOCIATE
to indicate S1G capabilities which should override the
hardware capabilities in eg. the association request.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-4-thomas@adapt-ip.com
[johannes: always require both attributes together, commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An S1G BSS can beacon at either 1 or 2 MHz and the channel
width is unique to a given frequency. Ignore scan channel
width for now and use the allowed channel width.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When deleting a channel context, mac80211 would assing
NL80211_CHAN_WIDTH_20_NOHT as the default channel width.
This is wrong in S1G however, so instead get the allowed
channel width for a given channel.
Fixes eg. configuring strange (20Mhz) width during a scan
on the S1G band.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-2-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support 6 GHz scanning, by
* a new scan flag to scan for colocated BSSes advertised
by (and found) APs on 2.4 & 5 GHz
* doing the necessary reduced neighbor report parsing for
this, to find them
* adding the ability to split the scan request in case the
device by itself cannot support this.
Also add some necessary bits in mac80211 to not break with
these changes.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200918113313.232917c93af9.Ida22f0212f9122f47094d81659e879a50434a6a2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Because we can miss AP wakeup (beacon) while scanning other channels,
it's better go into wakeup state and inform the AP of that upon
returning to the operating channel, rather than staying asleep and
waiting for the next TIM indicating traffic for us.
This saves precious time, especially when we only have 200ms inter-
scan period for monitoring the active connection.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1593420923-26668-1-git-send-email-loic.poulain@linaro.org
[rewrite commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After commit d0186842ec ("net: vlan: Avoid using BUG() in
vlan_proto_idx()"), vlan_proto_idx() was changed to return a signed
integer, however one of its called: vlan_group_prealloc_vid() was still
using an unsigned integer for its return value, fix that.
Fixes: d0186842ec ("net: vlan: Avoid using BUG() in vlan_proto_idx()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 is a bit of a special snowflake, in that not all frames are
transmitted/received in the same way. L2 link-local frames are received
with the source port/switch ID information put in the destination MAC
address. For the rest, a tag_8021q header is used. So only the latter
frames displace the rest of the headers and need to use the generic flow
dissector procedure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: John Crispin <john@phrozen.org>
Cc: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 Broadcom tags in use, one places the DSA tag before the
Ethernet destination MAC address, and the other before the EtherType.
Nonetheless, both displace the rest of the headers, so this tagger can
use the generic flow dissector procedure which accounts for that.
The ASCII art drawing is a good reference though, so keep it but move it
somewhere else.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent mitigations against speculative execution exploits,
indirect function calls are more expensive and it would be good to avoid
them where possible.
In the case of DSA, most switch taggers will shift the EtherType and
next headers by a fixed amount equal to that tag's length in bytes.
So we can use a generic procedure to determine that, without calling
into custom tagger code. However we still leave the flow_dissect method
inside struct dsa_device_ops as an override for the generic function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6060 uses tag_trailer.c and the KSZ8795, KSZ9477 and
KSZ9893 switches also use tail tags.
Tell that to the DSA core, since this makes a difference for the flow
dissector. Most switches break the parsing of frame headers, but these
ones don't, so no flow dissector adjustment needs to be done for them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no tagger that returns anything other than zero, so just change
the return type appropriately.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 goals that we follow:
- Reduce the header size
- Make the header size equal between RX and TX
The issue that required long prefix on RX was the fact that the ocelot
DSA tag, being put before Ethernet as it is, would overlap with the area
that a DSA master uses for RX filtering (destination MAC address
mainly).
Now that we can ask DSA to put the master in promiscuous mode, in theory
we could remove the prefix altogether and call it a day, but it looks
like we can't. Using no prefix on ingress, some packets (such as ICMP)
would be received, while others (such as PTP) would not be received.
This is because the DSA master we use (enetc) triggers parse errors
("MAC rx frame errors") presumably because it sees Ethernet frames with
a bad length. And indeed, when using no prefix, the EtherType (bytes
12-13 of the frame, bits 96-111) falls over the REW_VAL field from the
extraction header, aka the PTP timestamp.
When turning the short (32-bit) prefix on, the EtherType overlaps with
bits 64-79 of the extraction header, which are a reserved area
transmitted as zero by the switch. The packets are not dropped by the
DSA master with a short prefix. Actually, the frames look like this in
tcpdump (below is a PTP frame, with an extra dsa_8021q tag - dadb 0482 -
added by a downstream sja1105).
89:0c:a9:f2:01:00 > 88:80:00:0a:00:1d, 802.3, length 0: LLC, \
dsap Unknown (0x10) Individual, ssap ProWay NM (0x0e) Response, \
ctrl 0x0004: Information, send seq 2, rcv seq 0, \
Flags [Response], length 78
0x0000: 8880 000a 001d 890c a9f2 0100 0000 100f ................
0x0010: 0400 0000 0180 c200 000e 001f 7b63 0248 ............{c.H
0x0020: dadb 0482 88f7 1202 0036 0000 0000 0000 .........6......
0x0030: 0000 0000 0000 0000 0000 001f 7bff fe63 ............{..c
0x0040: 0248 0001 1f81 0500 0000 0000 0000 0000 .H..............
0x0050: 0000 0000 0000 0000 0000 0000 ............
So the short prefix is our new default: we've shortened our RX frames by
12 octets, increased TX by 4, and headers are now equal between RX and
TX. Note that we still need promiscuous mode for the DSA master to not
drop it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently PTP is broken when ports are in standalone mode (the tagger
keeps printing this message):
sja1105 spi0.1: Expected meta frame, is 01-80-c2-00-00-0e in the DSA master multicast filter?
Sure, one might say "simply add 01-80-c2-00-00-0e to the master's RX
filter" but things become more complicated because:
- Actually all frames in the 01-80-c2-xx-xx-xx and 01-1b-19-xx-xx-xx
range are trapped to the CPU automatically
- The switch mangles bytes 3 and 4 of the MAC address via the incl_srcpt
("include source port [in the DMAC]") option, which is how source port
and switch id identification is done for link-local traffic on RX. But
this means that an address installed to the RX filter would, at the
end of the day, not correspond to the final address seen by the DSA
master.
Assume RX filtering lists on DSA masters are typically too small to
include all necessary addresses for PTP to work properly on sja1105, and
just request promiscuous mode unconditionally.
Just an example:
Assuming the following addresses are trapped to the CPU:
01-80-c2-00-00-00 to 01-80-c2-00-00-ff
01-1b-19-00-00-00 to 01-1b-19-00-00-ff
These are 512 addresses.
Now let's say this is a board with 3 switches, and 4 ports per switch.
The 512 addresses become 6144 addresses that must be managed by the DSA
master's RX filtering lists.
This may be refined in the future, but for now, it is simply not worth
it to add the additional addresses to the master's RX filter, so simply
request it to become promiscuous as soon as the driver probes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently DSA assumes that taggers don't mess with the destination MAC
address of the frames on RX. That is not always the case. Some DSA
headers are placed before the Ethernet header (ocelot), and others
simply mangle random bytes from the destination MAC address (sja1105
with its incl_srcpt option).
Currently the DSA master goes to promiscuous mode automatically when the
slave devices go too (such as when enslaved to a bridge), but in
standalone mode this is a problem that needs to be dealt with.
So give drivers the possibility to signal that their tagging protocol
will get randomly dropped otherwise, and let DSA deal with fixing that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sections of device flash may contain settings or device identifying
information. When performing a flash update, it is generally expected
that these settings and identifiers are not overwritten.
However, it may sometimes be useful to allow overwriting these fields
when performing a flash update. Some examples include, 1) customizing
the initial device config on first programming, such as overwriting
default device identifying information, or 2) reverting a device
configuration to known good state provided in the new firmware image, or
3) in case it is suspected that current firmware logic for managing the
preservation of fields during an update is broken.
Although some devices are able to completely separate these types of
settings and fields into separate components, this is not true for all
hardware.
To support controlling this behavior, a new
DEVLINK_ATTR_FLASH_UPDATE_OVERWRITE_MASK is defined. This is an
nla_bitfield32 which will define what subset of fields in a component
should be overwritten during an update.
If no bits are specified, or of the overwrite mask is not provided, then
an update should not overwrite anything, and should maintain the
settings and identifiers as they are in the previous image.
If the overwrite mask has the DEVLINK_FLASH_OVERWRITE_SETTINGS bit set,
then the device should be configured to overwrite any of the settings in
the requested component with settings found in the provided image.
Similarly, if the DEVLINK_FLASH_OVERWRITE_IDENTIFIERS bit is set, the
device should be configured to overwrite any device identifiers in the
requested component with the identifiers from the image.
Multiple overwrite modes may be combined to indicate that a combination
of the set of fields that should be overwritten.
Drivers which support the new overwrite mask must set the
DEVLINK_SUPPORT_FLASH_UPDATE_OVERWRITE_MASK in the
supported_flash_update_params field of their devlink_ops.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink core recently gained support for checking whether the driver
supports a flash_update parameter, via `supported_flash_update_params`.
However, parameters are specified as function arguments. Adding a new
parameter still requires modifying the signature of the .flash_update
callback in all drivers.
Convert the .flash_update function to take a new `struct
devlink_flash_update_params` instead. By using this structure, and the
`supported_flash_update_params` bit field, a new parameter to
flash_update can be added without requiring modification to existing
drivers.
As before, all parameters except file_name will require driver opt-in.
Because file_name is a necessary field to for the flash_update to make
sense, no "SUPPORTED" bitflag is provided and it is always considered
valid. All future additional parameters will require a new bit in the
supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing .flash_update, drivers which do not support
per-component update are manually checking the component parameter to
verify that it is NULL. Without this check, the driver might accept an
update request with a component specified even though it will not honor
such a request.
Instead of having each driver check this, move the logic into
net/core/devlink.c, and use a new `supported_flash_update_params` field
in the devlink_ops. Drivers which will support per-component update must
now specify this by setting DEVLINK_SUPPORT_FLASH_UPDATE_COMPONENT in
the supported_flash_update_params in their devlink_ops.
This helps ensure that drivers do not forget to check for a NULL
component if they do not support per-component update. This also enables
a slightly better error message by enabling the core stack to set the
netlink bad attribute message to indicate precisely the unsupported
attribute in the message.
Going forward, any new additional parameter to flash update will require
a bit in the supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Cc: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_skb_mark_lost is used by RFC6675-SACK and can easily be replaced
with the new tcp_mark_skb_lost handler.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates and simplifes the loss marking logic used
by a few loss detections (RACK, RFC6675, NewReno). Previously
each detection uses a subset of several intertwined subroutines.
This unncessary complexity has led to bugs (and fixes of bug fixes).
tcp_mark_skb_lost now is the single one routine to mark a packet loss
when a loss detection caller deems an skb ist lost:
1. rewind tp->retransmit_hint_skb if skb has lower sequence or
all lost ones have been retransmitted.
2. book-keeping: adjust flags and counts depending on if skb was
retransmitted or not.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pure refactor to move tcp_mark_skb_lost to tcp_input.c to prepare
for the later loss marking consolidation.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_simple_retransmit() used for path MTU discovery may not adjust
the retransmit hint properly by deducting retrans_out before checking
it to adjust the hint. This patch fixes this by a correct routine
tcp_mark_skb_lost() already used by the RACK loss detection.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should remove a group from the sg_port hash only if it's an S,G
entry. This makes it correct and more symmetric with group add. Also
since *,G groups are not added to that hash we can hide a bug.
Fixes: 085b53c8be ("net: bridge: mcast: add sg_port rhashtable")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Is it just me, or is the logic written in a slightly convoluted way?
I find it a little easier to read this way.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
seq_puts is a lot cheaper than seq_printf, so use that to print
literal strings.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Reserving space for a large READ payload requires special handling when
reserving space in the xdr buffer pages. One problem we can have is use
of the scratch buffer, which is used to get a pointer to a contiguous
region of data up to PAGE_SIZE. When using the scratch buffer, calls to
xdr_commit_encode() shift the data to it's proper alignment in the xdr
buffer. If we've reserved several pages in a vector, then this could
potentially invalidate earlier pointers and result in incorrect READ
data being sent to the client.
I get around this by looking at the amount of space left in the current
page, and never reserve more than that for each entry in the read
vector. This lets us place data directly where it needs to go in the
buffer pages.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Drop duplicate words in net/sunrpc/.
Also fix "Anyone" to be "Any one".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: linux-nfs@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
