IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
A bunch of fixes for vmwgfx 4.12 regressions and older stuff. In the latter
case either trivial, cc'd stable or requiring backports for stable.
* 'vmwgfx-fixes-4.12' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Bump driver minor and date
drm/vmwgfx: Remove unused legacy cursor functions
drm/vmwgfx: fix spelling mistake "exeeds" -> "exceeds"
drm/vmwgfx: Fix large topology crash
drm/vmwgfx: Make sure to update STDU when FB is updated
drm/vmwgfx: Make sure backup_handle is always valid
drm/vmwgfx: Handle vmalloc() failure in vmw_local_fifo_reserve()
drm/vmwgfx: Don't create proxy surface for cursor
drm/vmwgfx: limit the number of mip levels in vmw_gb_surface_define_ioctl()
drm/i915 fixes for v4.12-rc5
* tag 'drm-intel-fixes-2017-06-08' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: fix warning for unused variable
drm/i915: Fix 90/270 rotated coordinates for FBC
drm/i915: Restore has_fbc=1 for ILK-M
drm/i915: Workaround VLV/CHV DSI scanline counter hardware fail
drm/i915: Fix logical inversion for gen4 quirking
drm/i915: Guard against i915_ggtt_disable_guc() being invoked unconditionally
drm/i915: Always recompute watermarks when distrust_bios_wm is set, v2.
drm/i915: Prevent the system suspend complete optimization
drm/i915/psr: disable psr2 for resolution greater than 32X20
drm/i915: Hold a wakeref for probing the ring registers
drm/i915: Short-circuit i915_gem_wait_for_idle() if already idle
drm/i915: Disable decoupled MMIO
drm/i915/guc: Remove stale comment for q_fail
drm/i915: Serialize GTT/Aperture accesses on BXT
Driver Changes:
- kirin: Use correct dt port for the bridge (John)
- meson: Fix regression caused by adding HDMI support to allow board
configurations without HDMI (Neil)
Cc: John Stultz <john.stultz@linaro.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
* tag 'drm-misc-fixes-2017-06-07' of git://anongit.freedesktop.org/git/drm-misc:
drm/meson: Fix driver bind when only CVBS is available
drm: kirin: Fix drm_of_find_panel_or_bridge conversion
imx-drm: PRE clock gating, panelless LDB, and VDIC CSI selection fixes
- Keep the external clock input to the PRE ungated and only use the internal
soft reset to keep the module in low power state, to avoid sporadic startup
failures.
- Ignore -ENODEV return values from drm_of_find_panel_or_bridge in the LDB
driver to fix probing for devices that still do not specify a panel in the
device tree.
- Fix the CSI input selection to the VDIC. According to experiments, the real
behaviour differs a bit from the documentation.
* tag 'imx-drm-fixes-2017-06-08' of git://git.pengutronix.de/git/pza/linux:
gpu: ipu-v3: Fix CSI selection for VDIC
drm/imx: imx-ldb: Accept drm_of_find_panel_or_bridge failure
gpu: ipu-v3: pre: only use internal clock gating
drivers/gpu/drm/i915/intel_engine_cs.c: In function ‘intel_engine_is_idle’:
drivers/gpu/drm/i915/intel_engine_cs.c:1103:27: error: unused variable ‘dev_priv’ [-Werror=unused-variable]
struct drm_i915_private *dev_priv = engine->i915;
^~~~~~~~
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
While introducing HDMI support, component matching on connectors node
were bypassed since no driver would actually bind on the DT node.
But when only a CVBS connector is present, only a single node is found
in the graph, but ignored and a NULL match table is given to the
component code.
This code permits bypassing the components framework by binding directly
the DRM driver when no components needs to be loaded.
Fixes: a41e82e6c4 ("drm/meson: Add support for components")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1496067352-8733-1-git-send-email-narmstrong@baylibre.com
The scanline counter is bonkers on VLV/CHV DSI. The scanline counter
increment is not lined up with the start of vblank like it is on
every other platform and output type. This causes problems for
both the vblank timestamping and atomic update vblank evasion.
On my FFRD8 machine at least, the scanline counter increment
happens about 1/3 of a scanline ahead of the start of vblank (which
is where all register latching happens still). That means we can't
trust the scanline counter to tell us whether we're in vblank or not
while we're on that particular line. In order to keep vblank
timestamping in working condition when called from the vblank irq,
we'll leave scanline_offset at one, which means that the entire
line containing the start of vblank is considered to be inside
the vblank.
For the vblank evasion we'll need to consider that entire line
to be bad, since we can't tell whether the registers already
got latched or not. And we can't actually use the start of vblank
interrupt to get us past that line as the interrupt would fire
too soon, and then we'd up waiting for the next start of vblank
instead. One way around that would using the frame start
interrupt instead since that wouldn't fire until the next
scanline, but that would require some bigger changes in the
interrupt code. So for simplicity we'll just poll until we get
past the bad line.
v2: Adjust the comments a bit
Cc: stable@vger.kernel.org
Cc: Jonas Aaberg <cja@gmx.net>
Tested-by: Jonas Aaberg <cja@gmx.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99086
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161215174734.28779-1-ville.syrjala@linux.intel.com
Tested-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
(cherry picked from commit ec1b4ee283)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Since
commit bac2a909a0
Author: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Date: Wed Jan 21 02:17:42 2015 +0100
PCI / PM: Avoid resuming PCI devices during system suspend
PCI devices will default to allowing the system suspend complete
optimization where devices are not woken up during system suspend if
they were already runtime suspended. This however breaks the i915/HDA
drivers for two reasons:
- The i915 driver has system suspend specific steps that it needs to
run, that bring the device to a different state than its runtime
suspended state.
- The HDA driver's suspend handler requires power that it will request
from the i915 driver's power domain handler. This in turn requires the
i915 driver to runtime resume itself, but this won't be possible if the
suspend complete optimization is in effect: in this case the i915
runtime PM is disabled and trying to get an RPM reference returns
-EACCESS.
Solve this by requiring the PCI/PM core to resume the device during
system suspend which in effect disables the suspend complete optimization.
Regardless of the above commit the optimization stayed disabled for DRM
devices until
commit d14d2a8453
Author: Lukas Wunner <lukas@wunner.de>
Date: Wed Jun 8 12:49:29 2016 +0200
drm: Remove dev_pm_ops from drm_class
so this patch is in practice a fix for this commit. Another reason for
the bug staying hidden for so long is that the optimization for a device
is disabled if it's disabled for any of its children devices. i915 may
have a backlight device as its child which doesn't support runtime PM
and so doesn't allow the optimization either. So if this backlight
device got registered the bug stayed hidden.
Credits to Marta, Tomi and David who enabled pstore logging,
that caught one instance of this issue across a suspend/
resume-to-ram and Ville who rememberd that the optimization was enabled
for some devices at one point.
The first WARN triggered by the problem:
[ 6250.746445] WARNING: CPU: 2 PID: 17384 at drivers/gpu/drm/i915/intel_runtime_pm.c:2846 intel_runtime_pm_get+0x6b/0xd0 [i915]
[ 6250.746448] pm_runtime_get_sync() failed: -13
[ 6250.746451] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul
snd_hda_codec_realtek snd_hda_codec_generic ghash_clmulni_intel e1000e snd_hda_codec snd_hwdep snd_hda_core ptp mei_me pps_core snd_pcm lpc_ich mei prime_
numbers i2c_hid i2c_designware_platform i2c_designware_core [last unloaded: i915]
[ 6250.746512] CPU: 2 PID: 17384 Comm: kworker/u8:0 Tainted: G U W 4.11.0-rc5-CI-CI_DRM_334+ #1
[ 6250.746515] Hardware name: /NUC5i5RYB, BIOS RYBDWi35.86A.0362.2017.0118.0940 01/18/2017
[ 6250.746521] Workqueue: events_unbound async_run_entry_fn
[ 6250.746525] Call Trace:
[ 6250.746530] dump_stack+0x67/0x92
[ 6250.746536] __warn+0xc6/0xe0
[ 6250.746542] ? pci_restore_standard_config+0x40/0x40
[ 6250.746546] warn_slowpath_fmt+0x46/0x50
[ 6250.746553] ? __pm_runtime_resume+0x56/0x80
[ 6250.746584] intel_runtime_pm_get+0x6b/0xd0 [i915]
[ 6250.746610] intel_display_power_get+0x1b/0x40 [i915]
[ 6250.746646] i915_audio_component_get_power+0x15/0x20 [i915]
[ 6250.746654] snd_hdac_display_power+0xc8/0x110 [snd_hda_core]
[ 6250.746661] azx_runtime_resume+0x218/0x280 [snd_hda_intel]
[ 6250.746667] pci_pm_runtime_resume+0x76/0xa0
[ 6250.746672] __rpm_callback+0xb4/0x1f0
[ 6250.746677] ? pci_restore_standard_config+0x40/0x40
[ 6250.746682] rpm_callback+0x1f/0x80
[ 6250.746686] ? pci_restore_standard_config+0x40/0x40
[ 6250.746690] rpm_resume+0x4ba/0x740
[ 6250.746698] __pm_runtime_resume+0x49/0x80
[ 6250.746703] pci_pm_suspend+0x57/0x140
[ 6250.746709] dpm_run_callback+0x6f/0x330
[ 6250.746713] ? pci_pm_freeze+0xe0/0xe0
[ 6250.746718] __device_suspend+0xf9/0x370
[ 6250.746724] ? dpm_watchdog_set+0x60/0x60
[ 6250.746730] async_suspend+0x1a/0x90
[ 6250.746735] async_run_entry_fn+0x34/0x160
[ 6250.746741] process_one_work+0x1f2/0x6d0
[ 6250.746749] worker_thread+0x49/0x4a0
[ 6250.746755] kthread+0x107/0x140
[ 6250.746759] ? process_one_work+0x6d0/0x6d0
[ 6250.746763] ? kthread_create_on_node+0x40/0x40
[ 6250.746768] ret_from_fork+0x2e/0x40
[ 6250.746778] ---[ end trace 102a62fd2160f5e6 ]---
v2:
- Use the new pci_dev->needs_resume flag, to avoid any overhead during
the ->pm_prepare hook. (Rafael)
v3:
- Update commit message to reference the actual regressing commit.
(Lukas)
v4:
- Rebase on v4 of patch 1/2.
Fixes: d14d2a8453 ("drm: Remove dev_pm_ops from drm_class")
References: https://bugs.freedesktop.org/show_bug.cgi?id=100378
References: https://bugs.freedesktop.org/show_bug.cgi?id=100770
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Marta Lofstedt <marta.lofstedt@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: linux-pci@vger.kernel.org
Cc: <stable@vger.kernel.org> # v4.10.x: 4d071c3 - PCI/PM: Add needs_resume flag
Cc: <stable@vger.kernel.org> # v4.10.x
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Marta Lofstedt <marta.lofstedt@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1493726649-32094-2-git-send-email-imre.deak@intel.com
(cherry picked from commit adfdf85d79)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
While the atomic modesetting capability is signaled also elsewhere, also
reflect it by a driver minor bump.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
These function implementations and/or declarations are no longer used
now that atomic is enabled.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reported-by: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Trivial fix to spelling mistake in DRM_ERROR error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
The previous attempt at this had an issue with with num_clips > 1
because it would always end up using the coordinates of the last
clip while using width and height calculated from the bounding
box of all the clips.
So if the last clip happens to be not at the top-left corner of
the bounding box, the CPU blit operation would go out of bounds.
The original intent was to coalesce all the clips into one blit,
and to do that we need to also track the starting point of the
content buffer.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
When a new FB is bound, we have to send an update command otherwise
the new FB may not be shown
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
When vmw_gb_surface_define_ioctl() is called with an existing buffer,
we end up returning an uninitialized variable in the backup_handle.
The fix is to first initialize backup_handle to 0 just to be sure, and
second, when a user-provided buffer is found, we will use the
req->buffer_handle as the backup_handle.
Cc: <stable@vger.kernel.org>
Reported-by: Murray McAllister <murray.mcallister@insomniasec.com>
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
With atomic, the cursor surface is treated like a FB. Creating
a proxy surface for cursor doesn't gain us much benefit.
This fixes the issue on atomic enabled 2D VMs where the cursor
disappears.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
BXT has a H/W issue with IOMMU which can lead to system hangs when
Aperture accesses are queued within the GAM behind GTT Accesses.
This patch avoids the condition by wrapping all GTT updates in stop_machine
and using a flushing read prior to restarting the machine.
The stop_machine guarantees no new Aperture accesses can begin while
the PTE writes are being emmitted. The flushing read ensures that
any following Aperture accesses cannot begin until the PTE writes
have been cleared out of the GAM's fifo.
Only FOLLOWING Aperture accesses need to be separated from in flight
PTE updates. PTE Writes may follow tightly behind already in flight
Aperture accesses, so no flushing read is required at the start of
a PTE update sequence.
This issue was reproduced by running
igt/gem_readwrite and
igt/gem_render_copy
simultaneously from different processes, each in a tight loop,
with INTEL_IOMMU enabled.
This patch was originally published as:
drm/i915: Serialize GTT Updates on BXT
[Note: This will cause a performance penalty for some use cases, but
avoiding hangs trumps performance hits. This may need to be worked
around in Mesa to recover the lost performance.]
v2: Move bxt/iommu detection into static function
Remove #ifdef CONFIG_INTEL_IOMMU protection
Make function names more reflective of purpose
Move flushing read into static function
v3: Tidy up for checkpatch.pl
Testcase: igt/gem_concurrent_blit
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: John Harrison <john.C.Harrison@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1495641251-30022-1-git-send-email-jon.bloomfield@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 0ef34ad622)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The description of the CSI_SEL bit in the i.MX6 reference manual is
incorrect. It states "This bit defines which CSI is the input to the
IC. This bit is effective only if IC_INPUT is bit cleared".
From experiment it was found this is in fact not correct. The CSI_SEL
bit selects which CSI is input to _both_ the VDIC _and_ the IC. If the
IC_INPUT bit is set so that the IC is receiving from the VDIC, the IC
ignores the CSI_SEL bit, but CSI_SEL still selects which CSI the VDIC
receives from in that case.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Not having an endpoint bound in DT should not cause a failure here,
there are fallbacks. So explicitly accept a missing endpoint.
This behavior change was introduced by refactoring in drm_of parsing
code and it should not require dts changes.
In particular this fixes imx6qdl-sabreauto boards.
Link: https://lists.freedesktop.org/archives/dri-devel/2017-May/141233.html
Fixes: ebc9446135 ("drm: convert drivers to use drm_of_find_panel_or_bridge")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
By setting the SFTRST bit, the PRE will be held in the lowest power state
with clocks to the internal blocks gated. When external clock gating is
used (from the external clock controller, or by setting the CLKGATE bit)
the PRE will sporadically fail to start.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: d2a3423258 ("gpu: ipu-v3: add driver for Prefetch Resolve Engine")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Core Changes:
- Grab locks in drm_atomic_helper_resume() (Daniel)
- Fix oops when unplugging USB device (expand cleanup in drm_unplug_dev) (Hans)
Driver Changes:
- rockchip: Don't output 10-bit format to 8-bit encoders (Mark)
Cc: Mark yao <mark.yao@rock-chips.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Hans de Goede <hdegoede@redhat.com>
* tag 'drm-misc-fixes-2017-06-02' of git://anongit.freedesktop.org/git/drm-misc:
drm: Fix oops + Xserver hang when unplugging USB drm devices
drm: Fix locking in drm_atomic_helper_resume
drm/rockchip: Correct vop out_mode configure
4 nouveau regression fixes.
* 'linux-4.12' of git://github.com/skeggsb/linux:
drm/nouveau/tmr: fully separate alarm execution/pending lists
drm/nouveau: enable autosuspend only when it'll actually be used
drm/nouveau: replace multiple open-coded runpm support checks with function
drm/nouveau/kms/nv50: add null check before pointer dereference
Reusing the list_head for both is a bad idea. Callback execution is done
with the lock dropped so that alarms can be rescheduled from the callback,
which means that with some unfortunate timing, lists can get corrupted.
The execution list should not require its own locking, the single function
that uses it can only be called from a single context.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Add null check before dereferencing pointer asyc
Addresses-Coverity-ID: 1397932
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pull drm displayport quirk support:
"DP quirk for usb c dongles.
As mentioned I have a separate request for fixing a regression, but
also keeping the broken hw working, for certain USB-C DP adapters they
require a minimised n/m parameters, but an attempt to do this
generically has failed, we need to quirk these specific adapters.
However doing it generically regressed some eDP panels.
This pull adds the infrastructure and a quirk for the adapter"
* tag 'drm-dp-quirk-for-v4.12-rc4' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Detect USB-C specific dongles before reducing M and N
drm/dp: start a DPCD based DP sink/branch device quirk database
drm/i915: use drm DP helper to read DPCD desc
drm/dp: add helper for reading DP sink/branch device desc from DPCD
commit a39be606f9 ("drm: Do a full device unregister when unplugging")
causes backtraces like this one when unplugging an usb drm device while
it is in use:
usb 2-3: USB disconnect, device number 25
------------[ cut here ]------------
WARNING: CPU: 0 PID: 242 at drivers/gpu/drm/drm_mode_config.c:424
drm_mode_config_cleanup+0x220/0x280 [drm]
...
RIP: 0010:drm_mode_config_cleanup+0x220/0x280 [drm]
...
Call Trace:
gm12u320_modeset_cleanup+0xe/0x10 [gm12u320]
gm12u320_driver_unload+0x35/0x70 [gm12u320]
drm_dev_unregister+0x3c/0xe0 [drm]
drm_unplug_dev+0x12/0x60 [drm]
gm12u320_usb_disconnect+0x36/0x40 [gm12u320]
usb_unbind_interface+0x72/0x280
device_release_driver_internal+0x158/0x210
device_release_driver+0x12/0x20
bus_remove_device+0x104/0x180
device_del+0x1d2/0x350
usb_disable_device+0x9f/0x270
usb_disconnect+0xc6/0x260
...
[drm:drm_mode_config_cleanup [drm]] *ERROR* connector Unknown-1 leaked!
------------[ cut here ]------------
WARNING: CPU: 0 PID: 242 at drivers/gpu/drm/drm_mode_config.c:458
drm_mode_config_cleanup+0x268/0x280 [drm]
...
<same Call Trace>
---[ end trace 80df975dae439ed6 ]---
general protection fault: 0000 [#1] SMP
...
Call Trace:
? __switch_to+0x225/0x450
drm_mode_rmfb_work_fn+0x55/0x70 [drm]
process_one_work+0x193/0x3c0
worker_thread+0x4a/0x3a0
...
RIP: drm_framebuffer_remove+0x62/0x3f0 [drm] RSP: ffffb776c39dfd98
---[ end trace 80df975dae439ed7 ]---
After which the system is unusable this is caused by drm_dev_unregister
getting called immediately on unplug, which calls the drivers unload
function which calls drm_mode_config_cleanup which removes the framebuffer
object while userspace is still holding a reference to it.
Reverting commit a39be606f9 ("drm: Do a full device unregister
when unplugging") leads to the following oops on unplug instead,
when userspace closes the last fd referencing the drm_dev:
sysfs group 'power' not found for kobject 'card1-Unknown-1'
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2459 at fs/sysfs/group.c:237
sysfs_remove_group+0x80/0x90
...
RIP: 0010:sysfs_remove_group+0x80/0x90
...
Call Trace:
dpm_sysfs_remove+0x57/0x60
device_del+0xfd/0x350
device_unregister+0x1a/0x60
drm_sysfs_connector_remove+0x39/0x50 [drm]
drm_connector_unregister+0x5a/0x70 [drm]
drm_connector_unregister_all+0x45/0xa0 [drm]
drm_modeset_unregister_all+0x12/0x30 [drm]
drm_dev_unregister+0xca/0xe0 [drm]
drm_put_dev+0x32/0x60 [drm]
drm_release+0x2f3/0x380 [drm]
__fput+0xdf/0x1e0
...
---[ end trace ecfb91ac85688bbe ]---
BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8
IP: down_write+0x1f/0x40
...
Call Trace:
debugfs_remove_recursive+0x55/0x1b0
drm_debugfs_connector_remove+0x21/0x40 [drm]
drm_connector_unregister+0x62/0x70 [drm]
drm_connector_unregister_all+0x45/0xa0 [drm]
drm_modeset_unregister_all+0x12/0x30 [drm]
drm_dev_unregister+0xca/0xe0 [drm]
drm_put_dev+0x32/0x60 [drm]
drm_release+0x2f3/0x380 [drm]
__fput+0xdf/0x1e0
...
---[ end trace ecfb91ac85688bbf ]---
This is caused by the revert moving back to drm_unplug_dev calling
drm_minor_unregister which does:
device_del(minor->kdev);
dev_set_drvdata(minor->kdev, NULL); /* safety belt */
drm_debugfs_cleanup(minor);
Causing the sysfs entries to already be removed even though we still
have references to them in e.g. drm_connector.
Note we must call drm_minor_unregister to notify userspace of the unplug
of the device, so calling drm_dev_unregister is not completely wrong the
problem is that drm_dev_unregister does too much.
This commit fixes drm_unplug_dev by not only reverting
commit a39be606f9 ("drm: Do a full device unregister when unplugging")
but by also adding a call to drm_modeset_unregister_all before the
drm_minor_unregister calls to make sure all sysfs entries are removed
before calling device_del(minor->kdev) thereby also fixing the second
set of oopses caused by just reverting the commit.
Fixes: a39be606f9 ("drm: Do a full device unregister when unplugging")
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jeffy <jeffy.chen@rock-chips.com>
Cc: Marco Diego Aurélio Mesquita <marcodiegomesquita@gmail.com>
Reported-by: Marco Diego Aurélio Mesquita <marcodiegomesquita@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601115430.4113-1-hdegoede@redhat.com
DP sink specific quirks
* tag 'topic/dp-quirks-2017-05-31' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Detect USB-C specific dongles before reducing M and N
drm/dp: start a DPCD based DP sink/branch device quirk database
drm/i915: use drm DP helper to read DPCD desc
drm/dp: add helper for reading DP sink/branch device desc from DPCD
Pull gcc-plugin prepwork from Kees Cook:
"Use designated initializers for mtk-vcodec, powerplay, amdgpu, and
sgi-xp. Use ERR_CAST() to avoid cross-structure cast in ocf2, ntfs,
and NFS.
Christoph Hellwig recommended that I send these fixes now, rather than
waiting for the v4.13 merge window. These are all initializer and cast
fixes needed for the future randstruct plugin that haven't been picked
up by the respective maintainers"
* tag 'gcc-plugins-v4.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
mtk-vcodec: Use designated initializers
drm/amd/powerplay: Use designated initializers
drm/amdgpu: Use designated initializers
sgi-xp: Use designated initializers
ocfs2: Use ERR_CAST() to avoid cross-structure cast
ntfs: Use ERR_CAST() to avoid cross-structure cast
NFS: Use ERR_CAST() to avoid cross-structure cast
- Fix a regression to description of exynos_drm_crtc
- Remove preclose hook of Exynos
. This was a exynos change of the patch series[1] merged already.
- Fix one dt broken issue
- Make sure to release bridge_node of Exynos MIPI-DSI driver.
[1] https://lists.freedesktop.org/archives/dri-devel/2017-March/135111.html
* tag 'exynos-drm-fixes-for-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: clean up description of exynos_drm_crtc
drm/exynos: dsi: Remove bridge node reference in removal
drm/exynos: dsi: Fix the parse_dt function
drm/exynos: Merge pre/postclose hooks
a few fixes for 4.12..
* 'msm-fixes-4.12-rc4' of git://people.freedesktop.org/~robclark/linux:
drm/msm: Fix the check for the command size
drm/msm: Take the mutex before calling msm_gem_new_impl
drm/msm: for array in-fences, check if all backing fences are from our own context before waiting
drm/msm: constify irq_domain_ops
drm/msm/mdp5: release hwpipe(s) for unused planes
drm/msm: Reuse dma_fence_release.
drm/msm: Expose our reservation object when exporting a dmabuf.
drm/msm/gpu: check legacy clk names in get_clocks()
drm/msm/mdp5: use __drm_atomic_helper_plane_duplicate_state()
drm/msm: select PM_OPP
drm/i915 fixes for v4.12-rc4
* tag 'drm-intel-fixes-2017-05-29' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Stop pretending to mask/unmask LPE audio interrupts
drm/i915/selftests: Silence compiler warning in igt_ctx_exec
Revert "drm/i915: Restore lost "Initialized i915" welcome message"
drm/i915/gvt: clean up unsubmited workloads before destroying kmem cache
drm/i915/gvt: Disable compression workaround for Gen9
drm/i915: set initialised only when init_context callback is NULL
drm/i915: Fix new -Wint-in-bool-context gcc compiler warning
drm/i915: use vma->size for appgtt allocate_va_range
drm/i915: Do not sync RCU during shrinking
We need program ring buffer on instance 1 register space domain,
when only if instance 1 available, with two instances or instance 0,
and we need only program instance 0 regsiter space domain for ring.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
