IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
From: Russell King <rmk@armlinux.org.uk>
As per the patches posted, discussed and tested by Peter Rosin, this
converts TDA998x to a bridge driver, while still allowing Armada and
TI LCDC to continue using it as they always have done. It also gets
rid of the private .fill_modes function, and tweaks the TMDS divider
calculation to be more correct to the available information.
[airlied: fixed two conflicts]
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180802093421.GA29670@rmk-PC.armlinux.org.uk
The serializer PLL divider is a power-of-two divider, so our calculation
which assumes that it's a numerical divider is incorrect. Replace it
with one that results in a power-of-two divider value instead.
Tested with all supported modes with a Samsung S24C750.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
We can achieve the same effect via the get_modes() method, rather than
wrapping the fill_modes helper.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Move the mode_valid() implementation to the bridge instead of the
connector, as we're checking the bridge's capabilities.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Register the bridge outside of the component helper as we have
drivers that wish to use the tda998x without its encoder.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cleanup the code a little from the effects of the previous changes:
- Move tda998x_destroy() to be above tda998x_create()
- Use 'dev' directly in tda998x_create() where appropriate.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Move the tda998x_priv allocation inside tda998x_create() and simplify
the tda998x_create()'s arguments. Pass the same to tda998x_destroy().
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Convert tda998x to a bridge driver with built-in encoder support for
compatibility with existing component drivers.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Move the non-DT configuration of the TDA998x into tda998x_create()
so that we do all setup in one place.
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This fits better with the drm_bridge callbacks for when this
driver becomes a drm_bridge.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
[edited by rmk to just split the tda998x_encoder_dpms() function
and restore the double-disable protection we originally had,
preserving original behaviour.]
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
We got a few conflicts in drm_atomic.c after merging the DRM writeback support,
now we need a backmerge to unlock develop development on drm-misc-next.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
The TDA998x is a HDMI transmitter with a TDA9950 CEC engine integrated
onto the same die. Add support for the TDA9950 CEC engine to the
TDA998x driver.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Always disable and clear interrupts at probe time to ensure that the
TDA998x is in a sane state. This ensures that the interrupt line,
which is also the CEC clock calibration signal, is always deasserted.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
We no longer use the CEC client to access the CEC part itself, so we can
move this later in the initialisation sequence.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
If tda998x_get_audio_ports() fails, and we requested the interrupt, we
fail to free the interrupt before returning failure. Rework the failure
cleanup code and exit paths so that we always clean up properly after an
error, and always propagate the error code.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Move the mutex, waitqueue, timer and detect work initialisation early
in the driver's initialisation, rather than being after we've registered
the CEC device.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cross-subsystem Changes:
- device tree doc for the Mitsubishi AA070MC01 and Tianma TM070RVHG71
panels (Lukasz Majewski) and for a 2nd endpoint on stm32 (Philippe Cornu)
Core Changes:
The most important changes are:
- Add drm_driver .last_close and .output_poll_changed helpers to reduce
fbdev emulation footprint in drivers (Noralf)
- Fix plane clipping in core and for vmwgfx (Ville)
Then we have a bunch of of improvement for print and debug such as the
addition of a framebuffer debugfs file. ELD connector, HDMI and
improvements. And a bunch of misc improvements, clean ups and style
changes and doc updates
[airlied: drop eld bits from amdgpu_dm]
Driver Changes:
- sii8620: filter unsupported modes and add DVI mode support (Maciej Purski)
- rockchip: analogix_dp: Remove unnecessary init code (Jeffy Chen)
- virtio, cirrus: add fb create_handle support to enable screenshots(Lepton Wu)
- virtio: replace reference/unreference with get/put (Aastha Gupta)
- vc4, gma500: Convert timers to use timer_setup() (Kees Cook)
- vc4: Reject HDMI modes with too high of clocks (Eric)
- vc4: Add support for more pixel formats (Dave Stevenson)
- stm: dsi: Rename driver name to "stm32-display-dsi" (Philippe Cornu)
- stm: ltdc: add a 2nd endpoint (Philippe Cornu)
- via: use monotonic time for VIA_WAIT_IRQ (Arnd Bergmann)
* tag 'drm-misc-next-2017-11-30' of git://anongit.freedesktop.org/drm/drm-misc: (96 commits)
drm/bridge: tc358767: add copyright lines
MAINTAINERS: change maintainer for Rockchip drm drivers
drm/vblank: Fix vblank timestamp debugs
drm/via: use monotonic time for VIA_WAIT_IRQ
dma-buf: Fix ifnullfree.cocci warnings
drm/printer: Add drm_vprintf()
drm/edid: Allow HDMI infoframe without VIC or S3D
video/hdmi: Allow "empty" HDMI infoframes
dma-buf/fence: Fix lock inversion within dma-fence-array
drm/sti: Handle return value of platform_get_irq_byname
drm/vc4: Add support for NV21 and NV61.
drm/vc4: Use .pixel_order instead of custom .flip_cbcr
drm/vc4: Add support for DRM_FORMAT_RGB888 and DRM_FORMAT_BGR888
drm: Move drm_plane_helper_check_state() into drm_atomic_helper.c
drm: Check crtc_state->enable rather than crtc->enabled in drm_plane_helper_check_state()
drm/vmwgfx: Try to fix plane clipping
drm/vmwgfx: Use drm_plane_helper_check_state()
drm/vmwgfx: Remove bogus crtc coords vs fb size check
gpu: gma500: remove unneeded DRIVER_LICENSE #define
drm: don't link DP aux i2c adapter to the hardware device node
...
HDMI 1.4b support the CEA video modes as per range of CEA-861-D (VIC 1-64).
For any other mode, the VIC filed in AVI infoframes should be 0.
HDMI 2.0 sinks, support video modes range as per CEA-861-F spec, which is
extended to (VIC 1-107).
This patch adds a bool input variable, which indicates if the connected
sink is a HDMI 2.0 sink or not. This will make sure that we don't pass a
HDMI 2.0 VIC to a HDMI 1.4 sink.
This patch touches all drm drivers, who are callers of this function
drm_hdmi_avi_infoframe_from_display_mode but to make sure there is
no change in current behavior, is_hdmi2 is kept as false.
In case of I915 driver, this patch:
- checks if the connected display is HDMI 2.0.
- HDMI infoframes carry one of this two type of information:
- VIC for 4K modes for HDMI 1.4 sinks
- S3D information for S3D modes
As CEA-861-F has already defined VICs for 4K videomodes, this
patch doesn't allow sending HDMI infoframes for HDMI 2.0 sinks,
until the mode is 3D.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jose Abreu <jose.abreu@synopsys.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
PS: This patch touches a few lines in few files, which were
already above 80 char, so checkpatch gives 80 char warning again.
- gpu/drm/omapdrm/omap_encoder.c
- gpu/drm/i915/intel_sdvo.c
V2: Rebase, Added r-b from Andrzej
V3: Addressed review comment from Ville:
- Do not send VICs in both AVI-IF and HDMI-IF
send only one of it.
V4: Rebase
V5: Added r-b from Neil.
Addressed review comments from Ville
- Do not block HDMI vendor IF, instead check for VIC while
handling AVI infoframes
V6: Rebase
V7: Rebase
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1499960000-9232-2-git-send-email-shashank.sharma@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
cec_read() is non-atomic in the presence of other I2C bus transactions
to the same device. This presents a problem when we add support for
the TDA9950 CEC engine part - both drivers can be trying to access the
device.
Avoid the inherent problems by switching to i2c_transfer() instead,
which allows us to perform more than one bus transaction atomically.
As this means we will be using I2C transactions rather than SMBUS, we
have to check that the host supports I2C functionality.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Some TDA998x contain several different I2C devices - there is the HDMI
encoder, and there is a TDA9950 CEC engine. These two share the same
interrupt signal.
In order to allow a driver for the CEC engine to work, we need to be
able to share the interrupt with the CEC driver, so convert the handler
and registration to allow this to happen.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Disabling the pre-filter block of the TDA998x saves 40mW and the colour
conversion block saves 15mW. As we always disable these two blocks, we
can power these sections of the chip down to save 55mW of unnecessary
power consumption.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
tda998x_audio_get_eld() is needlessly complex - the connector associated
with the encoder is always our own priv->connector. Remove this
complexity, but ensure that there are no races when copying out the ELD.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Group the TDA998x audio functions together rather than split between
two different locations in the file, keeping like code together.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Group the TDA998x connector functions and funcs structures together
before the encoder support, rather than scattered amongst the rest of
the file. This keeps like code together.
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The naming of tda998x_encoder_set_config() is a left-over from when
TDA998x was a slave encoder. Since this is part of the initialisation,
drop the _encoder from the name, and move it near tda998x_bind().
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Check for audio support by the attached sink by consulting the EDID
prior to enabling audio over the TMDS link. We must consult the EDID
after calling drm_helper_probe_single_connector_modes(), as this can
use an override EDID, or load a replacement EDID.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The CEA 861B specification indicates the situations when we are able to
send each infoframe based on the version of the EDID's CEA extension.
Update the tda998x driver to follow the CEA specification wrt sending
of infoframes.
Since we only support the generation of AVI version 2, this limits us
to CEA extension version 3, so we treat CEA extension version 2 as
CEA 861 (no infoframes, no audio.)
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Avoid a race between programming audio and an in-progress mode set.
A mode set is complex, and disables the ability to send infoframes
to the sink, and is disruptive to audio - we have to mute the audio
FIFO while doing a mode set.
If an attempt is made to start up the audio side, we will undo the
audio FIFO mute before the mode set has completed.
Move the lock so that we prevent audio interfering with an in-progress
mode set.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Avoid a racy access to the mode clock by storing the current mode clock
during a mode set under the audio mutex. This allows us to access it
from the audio path in a safe way.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
As priv->audio_params can now be changed at run time, we need to be more
careful about how we deal with a mode set. We must take the audio lock
while checking if there's a valid audio configuration.
However, it's slightly worse than that - during mode set, we mute the
audio, and it must not be unmuted until we have finished the mode set.
It is possible that the audio side may start while a mode set is in
progress, so take the audio_mutex lock around the whole mode setting
procedure.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
We will need the audio mutex initialised in all cases, so lets move this
to be early, rather than only being initialised for the DT case.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Connectors shouldn't be registered until the rest of the whole device
is set up, so that consistent state is presented to userspace.
As such, remove the calls to drm_connector_register() and
drm_connector_unregister() from tda998x, as these are now handled by
drm_dev_(un)register() itself.
To work with this change, the mali-dp and hdlcd bind and unbind
sequences have to be reordered, to ensure that the componentised
encoder/connector is bound before drm_dev_register() registers all
connectors. Similarly, the device must be unregistered before the
component is unbound.
Altogether, this allows other drivers using tda998x to be
de-midlayered, and to have less racy initialisation of their components.
Splitting this commit into three (one per driver) isn't possible without
intermediate breakage, so it is all squashed together here.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Register ASoC HDMI codec for audio functionality and adds device tree
binding for audio configuration.
With the registered HDMI codec the tda998x node can be used like a
regular codec node in ASoC card configurations. HDMI audio info-frame
and audio stream header is generated by the ASoC HDMI codec. The codec
also applies constraints for available sample-rates based on Edid Like
Data from the display. The device tree binding document has been
updated [1].
Part of this patch has been inspired by Jean Francoise's "drm/i2c: tda998x:
Add support of a DT graph of ports"-patch [2]. There may still be some
identical lines left from the original patch and some of the ideas
have come from there.
[1] Documentation/devicetree/bindings/display/bridge/tda998x.txt
[2] http://mailman.alsa-project.org/pipermail/alsa-devel/2015-July/095255.html
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Define struct tda998x_audio_params in include/drm/i2c/tda998x.h and
use it in pdata and for tda998x_configure_audio() parameters. Also
updates tda998x_write_aif() to take struct hdmi_audio_infoframe *
directly as a parameter.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
