IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This allows panels or bridges that need to send DSI commands during
pre_enable() to successfully send them. We delay DISP0 (aka the
actual display) enabling until after pre_enable so that pixels aren't
streaming before then.
v2: Just clear out the encoder->bridge value to disable the midlayer
calls (idea by Andrzej Hajda).
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621231759.29604-1-eric@anholt.net
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
VC4's DSI1 has a bug where the AXI connection is broken for 32-bit
writes from the CPU, so we use the DMA engine to DMA 32-bit values
into registers instead. That sleeps, so we can't do it from the top
half.
As a solution, use an interrupt thread so that all our writes happen
when sleeping is is allowed.
v2: Use IRQF_ONESHOT (suggested by Boris)
v3: Style nitpicks.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20171014001255.32005-1-eric@anholt.net
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> (v2)
We need the following things to happen in sequence:
DSI host creation
DSI device creation in the panel driver (needs DSI host)
DSI device attach from panel to host.
DSI drm_panel_add()
DSI encoder creation
DSI encoder's DRM panel/bridge attach
Unless we allow device creation while the host isn't up yet, we need
to break the -EPROBE_DEFER deadlock between the panel driver looking
up the host and the host driver looking up the panel. We can do so by
moving the DSI host creation outside of the component bind loop, and
the panel/bridge lookup/attach into the component bind process.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815234722.20700-3-eric@anholt.net
Reviewed-by: Archit Taneja <architt@codeaurora.org>
The incoming mode might have a missing vrefresh field if it came from
drmModeSetCrtc(), which the kernel is supposed to calculate using
drm_mode_vrefresh(). We could either use that or the adjusted_mode's
original vrefresh value.
However, we can maintain a more exact vrefresh value (not just the
integer approximation), by scaling by the ratio of our clocks.
v2: Use math suggested by Andrzej Hajda instead.
v3: Simplify math now that adjusted_mode->clock isn't padded.
v4: Drop some parens.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815234722.20700-2-eric@anholt.net
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
BCM2835's PLLD_DSI1 divider doesn't give us many choices for our pixel
clocks, so to support panels on the Raspberry Pi we need to set a
higher pixel clock rate than requested and adjust the mode we program
to extend out the HFP so that the refresh rate matches.
v2: Drop an unfinished comment (caught by Noralf)
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511235625.22427-2-eric@anholt.net
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If dsi_connector fails to allocate, the exit path via label 'fail'
checks if connector is null, which it always is, so the cleanup
that destroys connector is never going to be called. Hence the
failure path can be more optimally performed by removing this
and just returning ERR_PTR(-ENOMEM). This also removes the need
to initialize connector to NULL, and we can also remove ret too.
Detected by CoverityScan, CID#1399504 ("Logicall Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170203195624.7189-1-colin.king@canonical.com
The DSI0 and DSI1 blocks on the 2835 are related hardware blocks.
Some registers move around, and the featureset is slightly different,
as DSI1 (the 4-lane DSI) is a later version of the hardware block.
This driver doesn't yet enable DSI0, since we don't have any hardware
to test against, but it does put a lot of the register definitions and
code in place.
v2: Use the clk_hw interfaces, don't set CLK_IS_BASIC (from review by
Stephen Boyd)
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/20170131192912.11316-1-eric@anholt.net
