IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
The early serial code is not needed because we already have early
printk support provided by common/earlycons.c
This change also fixes the following build error that occurs when
CONFIG_SERIAL_8250 is not configured for Netlogic XLR boards:
arch/mips/built-in.o: In function `nlm_early_serial_setup':
setup.c:(.init.text+0x274): undefined reference to `early_serial_setup'
make: *** [vmlinux] Error 1
Reported-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6083/
Add the SYS block registers for XLP9XX, most of them have changed.
The wakeup sequence has been updated to set the coherent mode from
the main thread rather than the woken up thread.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6280/
Most IO block offsets have changed in XLP9XX. Update iomap.h to add the
new addresses of different SoC blocks like PIC, SYS, UART etc. that are
needed by the base code.
On XLP9xx, the SoC blocks of other nodes are seen on a PCI bus
corresponding to the node. Update iomap code to reflect this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6277/
Add MSI chip and MSIX chip definitions.
For MSI, we map the link interrupt to a MSI link IRQ which will
do a second level of dispatch based on the MSI status register.
The MSI chip definitions use the MSI enable register to enable
and disable the MSI irqs.
For MSI-X, we split the 32 available MSI-X vectors across the
four PCIe links (8 each). These PIC interrupts generate an IRQ
per link which uses a second level dispatch as well.
The MSI-X chip definition uses the standard functions to enable
and disable interrupts.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6270/
The early_init_devtree() API was removed in linux-next for 3.13 with
commit "mips: use early_init_dt_scan". This causes Netlogic XLP compile
to fail:
arch/mips/netlogic/xlp/setup.c:101: undefined reference to `early_init_devtree'
Add xlp_early_init_devtree() which uses the __dt_setup_arch() to
handle early device tree related initialization to fix this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
XLP2XX is first in the series of 28nm XLPII processors.
The changes are to:
* Add processor ID for XLP2XX to asm/cpu.h and kernel/cpu-probe.c.
* Add a cpu_is_xlpii() function to check for XLPII processors.
* Update xlp_mmu_init() to use config4 to enable extended TLB.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5698/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The reset and core initialization code should be available for
uniprocessor as well. This changes is just to take out the code
into a different file, without any change to the logic.
The change for uniprocessor initialization code is in a later patch.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5423/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add SWIOTLB config option and related files to Netlogic platform.
Some XLP SoC components like the SD/MMC interface cannot do DMA beyond
32-bit physical address. The SD/MMC driver can use memory outside this
range for IO, to support this we have to add bounce buffers implemented
by SWIOTLB.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: Ganesan Ramalingam <ganesanr@broadcom.com>
Patchwork: https://patchwork.linux-mips.org/patch/5410/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The definitions are not used anywhere else, and merging it will
make adding the new USB definitions for XLPII series easier.
While there, cleanup some whitespace in usb-init.c. There is no
change to logic due to this commit.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5027/
Acked-by: John Crispin <blogic@openwrt.org>
Update asm/netlogic/haldefs.h to extend register access functions
nlm_{read,write}_reg64() for 32-bit compilation. When compiled for 32-bit
the functions will read 64 IO registers with interrupts disabled.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5026/
Acked-by: John Crispin <blogic@openwrt.org>
The index for a device interrupt in the PIC interrupt routing table
changes for different chips in the XLP family. Avoid using the fixed
entries and derive the index value from the SoC device header.
Add workarounds for some devices which do not report the IRT index
correctly.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5025/
Acked-by: John Crispin <blogic@openwrt.org>
Remove the definitions of {read,write}_c0_{eirr,eimr}. These functions
are now unused after the PIC and IRQ code has been updated to use
optimized EIMR/EIRR functions which work on both 32-bit and 64-bit.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5021/
Acked-by: John Crispin <blogic@openwrt.org>
Remove the irq save/restore from write_c0_eimr(), as it is always called
with interrupts off.
This allows us to remove workaround in write_c0_eimr() to fix up the
flags used by local_irq_save. This fixup worked on XLR, but will break
when 32-bit support is added to r2 cpus like XLP.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5022/
Acked-by: John Crispin <blogic@openwrt.org>
The XLR/XLS/XLP PIC has a 8 countdown timers which run at the PIC
frequencey. One of these can be used as a clocksource to provide
timestamps that is common across cores. This can be used in place
of the count/compare clocksource which is per-CPU.
On XLR/XLS PIC registers are 32-bit, so we just use the lower 32-bits
of the PIC counter. On XLP, the whole 64-bit can be used.
Provide common macros and functions for PIC timer registers on XLR/XLS
and XLP, and use them to register a PIC clocksource.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4786/
Signed-off-by: John Crispin <blogic@openwrt.org>
Since we now use r4k cache code for Netlogic XLP, it is
better to split L1 icache among the active threads, so that
threads won't step on each other while flushing icache.
The L1 dcache is already split among the threads in the core.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4787/
Signed-off-by: John Crispin <blogic@openwrt.org>
Provide functions ack_c0_eirr(), set_c0_eimr(), clear_c0_eimr()
and read_c0_eirr_and_eimr() that do the EIMR and EIRR operations
and update the interrupt handling code to use these functions.
Also, use the EIMR register functions to mask interrupts in the
irq code.
The 64-bit interrupt request and mask registers (EIRR and EIMR) are
accessed when the interrupts are off, and the common operations are
to set or clear a bit in these registers. Using the 64-bit c0 access
functions for these operations is not optimal in 32-bit, because it
will disable/restore interrupts and split/join the 64-bit value during
each register access.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4790/
Signed-off-by: John Crispin <blogic@openwrt.org>