IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Prepare for deleting the static and dynamic power calculation and clean
the trace function. These two fields are going to be removed in the next
changes.
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> # for tracing code
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-2-lukasz.luba@arm.com
Use macro for temperature calculation
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210124801.13850-1-sumeet.r.pawnikar@intel.com
Added processor thermal device mail box interface for workload hints
setting. These hints will give indication to hardware to better manage
power and thermals. The supported hints are:
idle
semi_active
burusty
sustained
battery_life
For example when the system is on battery, the hardware can be less
aggressive in power ramp up.
This will create an attribute group at
/sys/bus/pci/devices/0000:00:04.0/workload_request
This folder contains two attributes:
workload_available_types : (RO): This shows available workload types
workload_type: (RW) : Allows to set and get current workload type
setting
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-4-srinivas.pandruvada@linux.intel.com
Add support for RFIM (Radio Frequency Interference Mitigation) support
via processor thermal PCI device. This drivers allows adjustment of
FIVR (Fully Integrated Voltage Regulator) and DDR (Double Data Rate)
frequencies to avoid RF interference with WiFi and 5G.
Switching voltage regulators (VR) generate radiated EMI or RFI at the
fundamental frequency and its harmonics. Some harmonics may interfere
with very sensitive wireless receivers such as Wi-Fi and cellular that
are integrated into host systems like notebook PCs. One of mitigation
methods is requesting SOC integrated VR (IVR) switching frequency to a
small % and shift away the switching noise harmonic interference from
radio channels. OEM or ODMs can use the driver to control SOC IVR
operation within the range where it does not impact IVR performance.
DRAM devices of DDR IO interface and their power plane can generate EMI
at the data rates. Similar to IVR control mechanism, Intel offers a
mechanism by which DDR data rates can be changed if several conditions
are met: there is strong RFI interference because of DDR; CPU power
management has no other restriction in changing DDR data rates;
PC ODMs enable this feature (real time DDR RFI Mitigation referred to as
DDR-RFIM) for Wi-Fi from BIOS.
This change exports two folders under /sys/bus/pci/devices/0000:00:04.0.
One folder "fivr" contains all attributes exposed for controling FIVR
features. The other folder "dvfs" contains all attributes for DDR
features.
Changes done to implement:
- New module for rfim interfaces
- Two new per processor features for DDR and FIVR
- Enable feature for Tiger Lake (FIVR only) and Alder Lake
The attributes exposed and explanation:
FIVR attributes
vco_ref_code_lo (RW): The VCO reference code is an 11-bit field and
controls the FIVR switching frequency. This is the 3-bit LSB field.
vco_ref_code_hi (RW): The VCO reference code is an 11-bit field and
controls the FIVR switching frequency. This is the 8-bit MSB field.
spread_spectrum_pct (RW): Set the FIVR spread spectrum clocking
percentage
spread_spectrum_clk_enable (RW): Enable/disable of the FIVR spread
spectrum clocking feature
rfi_vco_ref_code (RW): This field is a read only status register which
reflects the current FIVR switching frequency
fivr_fffc_rev (RW): This field indicated the revision of the FIVR HW.
DVFS attributes
rfi_restriction_run_busy (RW): Request the restriction of specific DDR
data rate and set this value 1. Self reset to 0 after operation.
rfi_restriction_err_code (RW): Values: 0 :Request is accepted, 1:Feature
disabled, 2: the request restricts more points than it is allowed
rfi_restriction_data_rate_Delta (RW): Restricted DDR data rate for RFI
protection: Lower Limit
rfi_restriction_data_rate_Base (RW): Restricted DDR data rate for RFI
protection: Upper Limit
ddr_data_rate_point_0 (RO): DDR data rate selection 1st point
ddr_data_rate_point_1 (RO): DDR data rate selection 2nd point
ddr_data_rate_point_2 (RO): DDR data rate selection 3rd point
ddr_data_rate_point_3 (RO): DDR data rate selection 4th point
rfi_disable (RW): Disable DDR rate change feature
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-3-srinivas.pandruvada@linux.intel.com
Added AlderLake PCI device id to support processor thermal driver. Reuse
the feature set (just includes RAPL) from previous generations.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-2-srinivas.pandruvada@linux.intel.com
The Processor Thermal PCI device supports multiple features. Currently
we export only RAPL. But we need more features from this device exposed
for Tiger Lake and Alder Lake based platforms. So re-structure the
current MMIO interface, so that more features can be added cleanly.
No functional changes are expected with this change.
Changes done in this patch:
- Using PCI_DEVICE_DATA(), hence names of defines changed
- Move RAPL MMIO code to its own module
- Move the RAPL MMIO offsets to RAPL MMIO module
- Adjust Kconfig dependency of PROC_THERMAL_MMIO_RAPL
- Per processor driver data now contains the supported features
- Moved all the common data structures and defines to a common header
file
- This new header file contains all the processor_thermal_* interfaces
- Based on the features supported the module interface is called
- Each module atleast provides one add and one remove function
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-1-srinivas.pandruvada@linux.intel.com
Currently the error message does not print the correct error code.
Fix it by initializing 'ret' to the proper error code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201202232448.2692-1-festevam@gmail.com
Remove the usage of interrupts for the normal temperature operation and
depend on the polling performed by the thermal core. This is done to
prepare to use the interrupts as they are intended to trigger once
specific trip points are passed and not to react to temperature changes
in the normal operational range.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126220923.3107213-1-niklas.soderlund+renesas@ragnatech.se
The only usage of these structs is to assign their address to the
thermal_zone_attribute_groups array, which consists of pointers to
const, so make them const to allow the compiler to put them in read-only
memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201128234342.36684-1-rikard.falkeborn@gmail.com
The PID coefficients should be estimated again when there was a change to
sustainable power value made by user. This change removes unused argument
'force' and makes the function ready for such updates.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-4-lukasz.luba@arm.com
The sustainable power value might come from the Device Tree or can be
estimated in run time. The sustainable power might be updated by the user
via sysfs interface, which should trigger new estimation of PID
coefficients. There is no need to estimate it every time when the
governor is called and temperature is high. Instead, store the estimated
value and make it available via standard sysfs interface, so it can be
checked from the user-space.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-3-lukasz.luba@arm.com
Intelligent Power Allocation (IPA) is built around the PID controller
concept. The initialization code tries to setup the environment based on
the information available in DT or estimate the value based on minimum
power reported by each of the cooling device. The estimation will have an
impact on the PID controller behaviour via the related 'k_po', 'k_pu',
'k_i' coefficients and also on the power budget calculation.
This change prevents the situation when 'k_i' is relatively big compared
to 'k_po' and 'k_pu' values. This might happen when the estimation for
'sustainable_power' returned small value, thus 'k_po' and 'k_pu' are
small.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-2-lukasz.luba@arm.com
The reference to acpi_gbl_FADT causes a build error when ACPI is not
enabled. Fix by making that conditional on CONFIG_ACPI.
../drivers/thermal/intel/intel_pch_thermal.c: In function 'pch_wpt_suspend':
../drivers/thermal/intel/intel_pch_thermal.c:217:8: error: 'acpi_gbl_FADT' undeclared (first use in this function); did you mean 'acpi_get_type'?
if (!(acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0))
^~~~~~~~~~~~~
Fixes: ef63b043ac86 ("thermal: intel: pch: fix S0ix failure due to PCH temperature above threshold")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Amit Kucheria <amitk@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201117023807.8266-1-rdunlap@infradead.org
Many monitoring tools read the CPU temperature using the hwmon
interface. Expose the thermal sensors on Amlogic boards as hwmon
devices.
Without this lm_sensors' "sensors" tool does not find any temperature
sensors. Now it prints:
cpu_thermal-virtual-0
Adapter: Virtual device
temp1: +44.7 C (crit = +110.0 C)
ddr_thermal-virtual-0
Adapter: Virtual device
temp1: +45.9 C (crit = +110.0 C)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201115190658.631578-1-martin.blumenstingl@googlemail.com
I noticed that I couldn't read the PCH temperature on my workstation
(C620 series chipset, w/ 2x Xeon Gold 5215 CPUs) directly, but had to go
through IPMI. Looking at the data sheet, it looks to me like the
existing intel PCH thermal driver should work without changes for
Lewisburg.
I suspect there's some other PCI IDs missing. But I hope somebody at
Intel would have an easier time figuring that out than I...
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/lkml/20200115184415.1726953-1-andres@anarazel.de/
Signed-off-by: Andres Freund <andres@anarazel.de>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201113204916.1144907-1-andres@anarazel.de
If state has not changed successfully and we updated cpufreq_state,
next time when the new state is equal to cpufreq_state (not changed
successfully last time), we will return directly and miss a
freq_qos_update_request() that should have been.
Fixes: 5130802ddbb1 ("thermal: cpu_cooling: Switch to QoS requests for freq limits")
Cc: v5.4+ <stable@vger.kernel.org> # v5.4+
Signed-off-by: Zhuguangqing <zhuguangqing@xiaomi.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201106092243.15574-1-zhuguangqing83@gmail.com
Function thermal_add_hwmon_sysfs, hwmon will be NULL when
new_hwmon_device = 0, so there is no need to check, kfree will
handle NULL point.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201102023121.3312-1-bernard@vivo.com
The bitmap_* API is the standard way to access data in the bitfield.
So convert irq_ack to return an unsigned long, and make things to use
bitmap API.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201109114624.23035-1-frank@allwinnertech.com
When system tries to enter S0ix suspend state, just after active load
scenarios, it fails due to PCH current temperature is higher than set
threshold.
This patch introduces delay loop mechanism that allows PCH temperature
to go down below threshold during suspend so it won't fail to enter S0ix.
Add delay loop timeout and count as module parameters for user to tune it,
if required based on system design. This change notifies the different
warning messages like when PCH temperature above the threshold and
executing delay loop. Also, notify the messages when it success or
failure for S0ix entry.
Previously out of 1000 runs around 3 to 5 times it might fail to enter
S0ix just after heavy workload. With this change, S0ix failures reduced
as PCH cools down below threshold.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201106170633.20838-1-sumeet.r.pawnikar@intel.com
MT8516 does not support thermal reset. Use device_reset_optional
instead of device_reset.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201021164231.3029956-3-fparent@baylibre.com
On RT or even on mainline with 'threadirqs' on the command line all
interrupts which are not explicitly requested with IRQF_NO_THREAD
run their handlers in thread context. The same applies to soft interrupts.
That means they are subject to the normal scheduler rules and no other
code is going to acquire that lock from hard interrupt context either,
so the irqsave() here is pointless in all cases.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1603760790-37748-1-git-send-email-tiantao6@hisilicon.com
The trip points are checked one by one with multiple condition
branches where one condition is enough to disable the trip point.
Merge all these conditions in a single 'OR' statement.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201027013743.62392-1-bernard@vivo.com
[dlezcano] Changed patch description
Since the power actor section has one function power_actor_set_power()
move it into Intelligent Power Allocation (IPA). There is no other user
of that helper function. It would also allow to remove the check of
cdev_is_power_actor() because the code which calls it in IPA already does
the needed check. Make the function static since only IPA use it.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-5-lukasz.luba@arm.com
Since the Intelligent Power Allocation (IPA) uses different way to get
minimum and maximum power for a given cooling device, the helper functions
are not needed. There is no other code which uses them, so remove the
helper functions.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-4-lukasz.luba@arm.com
The thermal cooling device specified in DT might be instantiated for
a thermal zone trip point with a limited set of OPPs to operate on. This
configuration should be supported by Intelligent Power Allocation (IPA),
since it is a standard for other governors. Change the code and allow IPA
to get power value of lower and upper bound set for a given cooling
device.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-3-lukasz.luba@arm.com
The upper and lower limits of thermal throttle state in the
DT do not apply to the Intelligent Power Allocation (IPA) governor.
Add the clamping for cooling device upper and lower limits in the
power_actor_set_power() used by IPA.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201007024332.30322-1-michael.kao@mediatek.com
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use dev_error_probe() to simplify the error handling on imx and imx8
platforms (Anson Huang)
- Use dedicated kobj_to_dev() instead of container_of() in the sysfs
core code (Tian Tao)
- Fix coding style by adding braces to a one line conditional
statement on rcar (Geert Uytterhoeven)
- Add DT binding documentation for the r8a774e1 platform and update
the Kconfig description supporting RZ/G2 SoCs (Lad Prabhakar)
- Simplify the return expression of stm_thermal_prepare on the stm32
platform (Qinglang Miao)
- Fix the unit in the function documentation for the idle injection
cooling device (Zhuguang Qing)
- Remove an unecessary mutex_init() in the core code (Qinglang Miao)
- Add support for keep alive events in the core code and the specific
int340x (Srinivas Pandruvada)
- Remove unused thermal zone variable in devfreq and cpufreq cooling
devices (Zhuguang Qing)
- Add the A100's THS controller support (Yangtao Li)
- Add power management on the omap3's bandgap sensor (Adam Ford)
- Fix a missing nlmsg_free in the netlink core error path (Jing Xiangfeng)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl+GwbYACgkQqDIjiipP
6E8IFAf/UnO1HqfK96FnVJXx5ClXFE8PQhdVejxBEsNCJqUOwlqfpyONy7mgwABb
EuOvp5ZLX6ly9xG6J4NJhE4gN4DxqRKe0S3bQMU+DX8TQHc3otDKHILJbHrJdOY+
BYZpGxuCjU9yZrsJopztZIcpG7cF78d39XCJVSrBhoOBqPLXNGZkUUzOv9+QQti3
ipdhqB3kUzkgDFgIrDxX8t0vybQZSbiRWNUGrw/WQjMsG0NGIarCUHW4wiaea6gU
L2x1QDR5h9hxEAJiTBarOtF7ZlE15fpria0mWfTgmNMArMEtRBL60kBnmYa4o3EG
CseR7x1MdTCSqLCzKGfQyKv5SFgnVg==
=P6zv
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Fix Kconfig typo "acces" -> "access" (Colin Ian King)
- Use dev_error_probe() to simplify the error handling on imx and imx8
platforms (Anson Huang)
- Use dedicated kobj_to_dev() instead of container_of() in the sysfs
core code (Tian Tao)
- Fix coding style by adding braces to a one line conditional statement
on rcar (Geert Uytterhoeven)
- Add DT binding documentation for the r8a774e1 platform and update the
Kconfig description supporting RZ/G2 SoCs (Lad Prabhakar)
- Simplify the return expression of stm_thermal_prepare on the stm32
platform (Qinglang Miao)
- Fix the unit in the function documentation for the idle injection
cooling device (Zhuguang Qing)
- Remove an unecessary mutex_init() in the core code (Qinglang Miao)
- Add support for keep alive events in the core code and the specific
int340x (Srinivas Pandruvada)
- Remove unused thermal zone variable in devfreq and cpufreq cooling
devices (Zhuguang Qing)
- Add the A100's THS controller support (Yangtao Li)
- Add power management on the omap3's bandgap sensor (Adam Ford)
- Fix a missing nlmsg_free in the netlink core error path (Jing
Xiangfeng)
* tag 'thermal-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal: core: Adding missing nlmsg_free() in thermal_genl_sampling_temp()
thermal: ti-soc-thermal: Enable addition power management
thermal: sun8i: Add A100's THS controller support
thermal: sun8i: add TEMP_CALIB_MASK for calibration data in sun50i_h6_ths_calibrate
dt-bindings: thermal: sun8i: Add binding for A100's THS controller
thermal: cooling: Remove unused variable *tz
thermal: int340x: Add keep alive response method
thermal: core: Add new event for sending keep alive notifications
thermal: int340x: Provide notification for OEM variable change
thermal: core: remove unnecessary mutex_init()
thermal/idle_inject: Fix comment of idle_duration_us and name of latency_ns
thermal: Kconfig: Update description for RCAR_GEN3_THERMAL config
thermal: stm32: simplify the return expression of stm_thermal_prepare()
dt-bindings: thermal: rcar-gen3-thermal: Add r8a774e1 support
thermal: rcar_thermal: Add missing braces to conditional statement
thermal: Use kobj_to_dev() instead of container_of()
thermal: imx8mm: Use dev_err_probe() to simplify error handling
thermal: imx: Use dev_err_probe() to simplify error handling
drivers: thermal: Kconfig: fix spelling mistake "acces" -> "access"
thermal_genl_sampling_temp() misses to call nlmsg_free() in an error path.
Jump to out_free to fix it.
Fixes: 1ce50e7d408ef2 ("thermal: core: genetlink support for events/cmd/sampling")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200929082652.59876-1-jingxiangfeng@huawei.com
The bandgap sensor can be idled when the processor is too, but it
isn't currently being done, so the power consumption of OMAP3
boards can elevated if the bangap sensor is enabled.
This patch attempts to use some additional power management
to idle the clock to the bandgap when not needed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Andreas Kemnade <andreas@kemnade.info> # GTA04
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200911123157.759379-1-aford173@gmail.com
For sun50i_h6_ths_calibrate(), the data read from nvmem needs a round of
calculation. On the other hand, the newer SOC may store other data in
the space other than 12bit sensor data. Add mask operation to read data
to avoid conversion error.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/dcf98648c16aff7649ff82438bfce6caae3e176f.1595572867.git.frank@allwinnertech.com
1. devfreq_cooling.c: The variable *tz is not used in
devfreq_cooling_get_requested_power(), devfreq_cooling_state2power()
and devfreq_cooling_power2state().
2. cpufreq_cooling.c: After 84fe2cab48590, the variable *tz is not used
anymore in cpufreq_get_requested_power(), cpufreq_state2power() and
cpufreq_power2state().
Remove the variable *tz.
Signed-off-by: zhuguangqing <zhuguangqing@xiaomi.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200914071101.13575-1-zhuguangqing83@gmail.com
When firmware requests keep alive response, send an event to user space
to confirm by using imok sysfs entry.
Create a new sysf entry called "imok". User space can write an integer,
which results in execution of IMOK ACPI method of INT3400 thermal zone
device. This results in sending response to firmware request for keep
alive.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200915223650.406046-4-srinivas.pandruvada@linux.intel.com
When we receive ACPI notification for OEM variable change pass the
notification to user space handler. This will avoid polling for
OEM variable change from user space.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200915223650.406046-2-srinivas.pandruvada@linux.intel.com
The mutex poweroff_lock is initialized statically. It is
unnecessary to initialize by mutex_init().
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200916062139.191233-1-miaoqinglang@huawei.com
According to Documentation/process/coding-style.rst, if one branch of a
conditional statement needs braces, both branches should use braces.
Fixes: bbcf90c0646ac797 ("thermal: Explicitly enable non-changing thermal zone devices")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200819092716.3191-1-geert+renesas@glider.be
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1597129185-8460-2-git-send-email-Anson.Huang@nxp.com
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1597129185-8460-1-git-send-email-Anson.Huang@nxp.com
Bulk of the genetlink users can use smaller ops, move them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to add maxattr and policy back to genl_ops, to enable
dumping per command policy to user space. This, however, would
cause bloat for all the families with global policies. Introduce
smaller version of ops (half the size of genl_ops). Translate
these smaller ops into a full blown struct before use in the
core.
v1:
- use struct assignment
- put a full copy of the op in struct genl_dumpit_info
- s/light/small/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
