IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
SoPine is a SoM by Pine64, which have a gold finger compatible with the
slot of DDR3 SODIMM (signals are not compatible), and have an A64, an
AXP803, a LPDDR3 DRAM chip, a power led and a MicroSD slot on it.
The card detect pin of the MicroSD slot on the SoM is pulled down, which
makes it unusable; however, the slot is at the surface of the SoM that
is closed to the baseboard, so it's nearly impossible to hot-swap it,
thus I make it non-removable.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A64 device tree file has some remnants of raw number references
to the CCU node, likely from when the CCU bindings and device tree
changes were first merged.
Convert these, and the R_CCU ones, to use the proper defined macros
from their respective device tree binding header files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pine64 exposes all A64 UARTs, not just UART0.
Since the pins can be used as GPIO, don't enable the new UART nodes by
default, but prepare the pinctrl settings to aid in activating them via
overlays, i.e., overriding the status property of &uartX nodes.
For UART4 (Euler) the safer route of not including RTS/CTS pins is chosen,
whereas for UART1 (Bluetooth) they are included.
Add the corresponding pinctrl nodes where missing.
Suggested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 have a RSB controller like the one on A23/A33 SoCs.
Add it and its pinmux.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enabling uart2 node currently leads to a /dev/ttyS1 device, with ttyS0..4
always present, causing confusion on the user's part.
dtc cannot resolve an overlay's &uart2 reference for strings, only for
phandles, so it would need to hardcode the full node path.
Avoid this and enforce reliable numbering by adding serialX aliases for:
UART1 - on Wifi/BT connector
UART2 - on Pi-2 connector
UART3 - on Euler connector
UART4 - on Euler connector
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
UART2 is exposed on the Pi connector of Pine64. Make a pinctrl node
available at the SoC level, to simplify enabling UART2 via DT overlay.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
NanoPi NEO2 is a board with the same size factor with the original
NanoPi NEO by FriendlyELEC.
It has a H5 instead of H3 on NanoPi NEO, and the ethernet is upgraded to
1Gbps (with external RTL8211E PHY).
Add support for this board.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orange Pi Prime is a new Allwinner H5-based SBC by Xunlong.
It's like a Orange Pi Plus 2E with H3 replaced with H5, eMMC replaced
with onboard SPI NOR Flash and wireless card changed to Realtek
RTL8723BS (with Bluetooth functionality).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Switch to use the new compatible for the SCPI sensors so that the
sensor readings are reported using the correct scale.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The dwmac-sun8i hardware is present on the Orange PI PC2.
It uses an external PHY rtl8211e via RGMII.
This patch create the needed regulator, emac and phy nodes.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i is an ethernet MAC hardware that support 10/100/1000
speed.
This patch enable the dwmac-sun8i on Allwinner H3/H5 SoC Device-tree.
SoC H3/H5 have an internal PHY, so optionals syscon and ephy are set.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch add the dt node for the syscon register present on the
Allwinner H3/H5
Only two register are present in this syscon and the only one useful is
the one dedicated to EMAC clock..
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that the R_CCU device tree binding headers have been merged, we
can convert the raw number references in the device trees to use the
defined macros.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The TX status trigger of the wlan interface is named phy0tx, so this
updates the default-trigger for the WLAN LED to use that instead.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the DT node for Kryo CPU clock controller on msm8996
devices.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
SMEM allows various subsystems/processors to share
memory/data (heap format) in order to enable various
peripherals.
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This regulator is not moving anywhere. Sit, stay...
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Stingray SoC has two instances of SDHCI controller
and one instance of iProc PWM.
Let's enable above mentioned devices in Stingray DT.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We have two instance of PL022 SPI controllers, one instance of
DMA PL330, and one non-secure SP805 Watchdog on Stingray SOC.
This patch adds DT nodes for the above mentioned devices in
Stingray DT.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Pramod KUMAR <pramod.kumar@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The GPIOs on Stingray SOC are based on iProc GPIOs hence
using this we add GPIO DT nodes for Stingray SOC.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch adds pinctrl and pinmux related DT nodes for
Stingray SOC.
For manageability, pinctrl and pinmum DT nodes are added
as separate DTSi file and included in main DTSi file.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Vikram Prakash <vikram.prakash@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch describes Stingray SOC clock tree using
DT nodes in Stingray DTS.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Broadcom Stingray SoC is a new member in Broadcom iProc
SoC family.
This patch adds initial DTS files for Broadcom Stingray SoC
and two of its reference boards (bcm958742k and bcm958742t).
We have lot of reference boards and large number of devices
in Broadcom Stingray SoC so eventually we will have quite
a few DTS files for Stingray. To tackle, we have added a
separate directory for Stingray DTS files.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds DT bindings info for Broadcom Stingray SOC
and related reference boards.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
ls1012a has separate input root clocks for core PLLs versus the platform
PLL, with the latter described as sysclk in the hw docs.
Accordingly, update the clock-frequency in sysclk to 125M as platform
input clock.
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "dis_rxdet_inp3_quirk" boolean property to USB3 node. This property
is used to disable rx detection in P3 PHY mode.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently SD UHS-I modes were enabled by default on LS208xARDB boards,
but the new LS2088ARDB RevF board didn't support them any more since SDHC
circuit had been reworked. This patch is to disable SD UHS-I modes by default
in case of any issue on LS2088ARDB RevF
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds an initial DT for the RTD1295 SoC and a TV box based on it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vjlA
-----END PGP SIGNATURE-----
Merge tag 'realtek-arm64-dt-for-4.12' of git://github.com/afaerber/linux into next/dt64
Realtek ARM64 based SoC DT for v4.12
This adds an initial DT for the RTD1295 SoC and a TV box based on it.
* tag 'realtek-arm64-dt-for-4.12' of git://github.com/afaerber/linux:
ARM64: dts: Add Realtek RTD1295 and Zidoo X9S
dt-bindings: arm: Add Realtek RTD1295 bindings
dt-bindings: Add vendor prefix for Zidoo
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add support for R-Car H3 ES2.0
* Break out common board support
* Set drive-strength for ravb pins for r8a7795/h3ulcb and r8a7796/m3ulcb
* Enable HDMI outputs on r8a7795/salvator-x
* Add R-Car audio to DT of r8a7796 SoC
* Add current sense amplifiers to DT of r8a779[56]/salvator-x
* Enable NFS-root on r8a7796/salvator-x
* Enable HS200 for eMMC on r8a779[56]/salvator-x,
r8a7795/h3ulcb and r8a7796/m3ulcb
* Enable EthernetAVB, I2C r8a7796/m3ulcb
* Update memory node to 2 GiB map on r8a7796/m3ulcb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cmye
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Renesas ARM64 Based SoC DT Updates for v4.13
* Add support for R-Car H3 ES2.0
* Break out common board support
* Set drive-strength for ravb pins for r8a7795/h3ulcb and r8a7796/m3ulcb
* Enable HDMI outputs on r8a7795/salvator-x
* Add R-Car audio to DT of r8a7796 SoC
* Add current sense amplifiers to DT of r8a779[56]/salvator-x
* Enable NFS-root on r8a7796/salvator-x
* Enable HS200 for eMMC on r8a779[56]/salvator-x,
r8a7795/h3ulcb and r8a7796/m3ulcb
* Enable EthernetAVB, I2C r8a7796/m3ulcb
* Update memory node to 2 GiB map on r8a7796/m3ulcb
* tag 'renesas-arm64-dt-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (35 commits)
arm64: dts: r8a7795: salvator-x: Add support for R-Car H3 ES2.0
arm64: dts: r8a7795: Add support for R-Car H3 ES2.0
arm64: dts: ulcb: Set drive-strength for ravb pins
arm64: dts: renesas: r8a7795-salvator-x: Enable HDMI outputs
arm64: dts: renesas: r8a7795-salvator-x: Add DU external dot clocks
arm64: dts: renesas: salvator-x: Add HDMI output connectors
arm64: dts: renesas: salvator-x: Add DU external dot clock sources
arm64: dts: renesas: r8a7795: Add HDMI encoder support
arm64: dts: salvator-x: Add panel backlight support
arm64: dts: r8a7796: Add PWM device nodes
arm64: dts: r8a7796: add Sound MIX support
arm64: dts: r8a7796: add Sound CTU support
arm64: dts: r8a7796: add Sound DVC support
arm64: dts: r8a7796: add Sound SRC support
arm64: dts: r8a7796: add Sound SSI DMA support
arm64: dts: r8a7796: add Sound SSI PIO support
arm64: dts: r8a7796: add AUDIO_DMAC support
arm64: dts: salvator-x: Add current sense amplifiers
arm64: dts: renesas: Extract common ULCB board support
arm64: dts: renesas: Extract common Salvator-X board support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
All SoCs supported up to now rely on the fallback binding of mt6577.
Fix the binding description to reflect this.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
This patch adds the SPICC Controller pins nodes for Amlogic GXL SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the SPICC Controller pins nodes for Amlogic GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic Meson GXL SoCs embeds an 10/100 Ethernet PHY, this patchs adds
the Link and Activity LEDs signals pins nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the AO and EE domain CEC pins nodes for the Amlogic Meson GXL SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the AO and EE domain CEC pins nodes for the Amlogic Meson GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The pull-enable register base was wrongly copied from the meson8b pinctrl node,
but was not used yet.
Fixes: c328666d58aa ("ARM64: dts: amlogic: Add Meson GX dtsi from GXBB")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The pull-enable register base was wrongly copied from the GXBB pinctrl node,
but was not used yet.
Fixes: fb0fe92294a9 ("ARM64: dts: meson-gxl: Add pinctrl nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The gpio-range was badly added on the GXL dtsi, the AO pin count is 10
instead of 14.
Fixes: 84412e4e857f ("ARM64: dts: meson-gxl: Add gpio-ranges properties")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The FriendlyARM NanoPi K2 is a single-board computer.
Cc: techsupport@friendlyarm.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The FriendlyARM NanoPi K2 is a single-board computer.
Cc: techsupport@friendlyarm.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The R-Box Pro is a TV box derived from Amlogic q200 reference design.
It uses an AP6255 Wifi module. It features an LED tube that lights a
surrounding stripe and the top logo in blue or red or pink'ish - blue
is on by default, and red (i.e., pink) is configured as panic indicator.
This device is available in at least two models, with 2 GB vs. 3 GB RAM
as well as varying eMMC size. The intent is to handle this with a single
.dts that gets the actual RAM size from U-Boot.
Cc: ada@kingnoval.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Cc: ada@kingnoval.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Their domain name is spelled kingnoval, but textually Kingnovel.
Cc: ada@kingnoval.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The rk3399 has multiple variants with different frequency ratings.
The operating points currently in the kernel stem from the op1 variant
used in Gru ChromeOS devices and may not be suitable for general rk3399
chips. Therefore bring it back to the official general operating points.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The OP1 is a rk3399 variant used in ChromeOS devices with a slightly
higher frequency rating compared to the regular rk3399, but right now
the only available operating points don't match either variant
with both needing adjustments to actually fit their specs.
Therefore introduce separate operting points, from the ChromeOS kernel,
for the OP1 and use it on Gru devices.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
