IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
ARConnect/MCIP Inter-Core-Interrupt module can't send interrupt to
local core. So use core intc capability to trigger software
interrupt to self, using an unsued IRQ #21.
This showed up as csd deadlock with LTP trace_sched on a dual core
system. This test acts as scheduler fuzzer, triggering all sorts of
schedulting activity. Trouble starts with IPI to self, which doesn't get
delivered (effectively lost due to H/w capability), but the msg intended
to be sent remain enqueued in per-cpu @ipi_data.
All subsequent IPIs to this core from other cores get elided due to the
IPI coalescing optimization in ipi_send_msg_one() where a pending msg
implies an IPI already sent and assumes other core is yet to ack it.
After the elided IPI, other core simply goes into csd_lock_wait()
but never comes out as this core never sees the interrupt.
Fixes STAR 9001008624
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org> [4.2]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC HS Cores support configurable multiple interrupt priorities of upto
16 levels.
There is processor "interrupt preemption threshhold" in STATUS32.E[4:1]
And several places need to set this up:
1. seed value as kernel is booting
2. seed value for user space programs
3. Arg to SLEEP instruction in idle task (what interrupt prio can wake)
4. Per-IRQ line prioirty (i.e. what is the priority of interrupt
raised by a peripheral or timer or perf counter...
Currently above sites use the highest priority 0. This can be potential
problem when multiple priorities are supported. e.g. user space could
only be interrupted by P0 interrupt, not others...
So turn this over and instead make default interruption level to be
the lowest priority possible 15. This should be fine even if there are
fewer priority levels configured (say two: P0 HIGH, P1 LOW)
This feature also effectively disables FIRQ feature if present in
hardware config. With old code, a P0 interrupt would be FIRQ, needing
special handling (ISR or Register Banks) which is NOT supported yet.
Now it not be P0 (P15 or whatever is lowest prio) so FIRQ is not
triggered.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Although kernel doesn't support the multiple IRQ priority levels provided
by HS38x core intc yet, ensure that the default prio value is used
anyways by relevant code.
SLEEP insn needs to be provided the IRQ priority level which can
interrupt it. This needs to be the default level which maynot
necessarily be 0 as assumed by current code.
This change allows a kernel with ARCV2_IRQ_DEF_PRIO = 1 to boot fine.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The issue was, on HS when interrupt is taken, IRQ_ACT is set and that is
NOT cleared unless we do RTIE (or manually clear it). Linux interrupt
handling has top and bottom halves. Latter lead to softirqs (which can
reschedule) AND expect interrupts to be REALLY re-enabled which was NOT
happening for us since we only SETI, dont clear IRQ_ACT
So we can have a state when both cores have taken interrupt (IRQ_ACT set),
get rescheduled, both send IPI and wait in CSD lock which will never be
cleared as cores can't take the pending IPI IRQ due to existing IRQ_ACT
set.
So local_irq_enable() now drops the IRQ_ACT.act bit to re-enable IRQs.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
