IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Syzbot reports the following WARNING:
[200~raw_local_irq_restore() called with IRQs enabled
WARNING: CPU: 1 PID: 1206 at kernel/locking/irqflag-debug.c:10
warn_bogus_irq_restore+0x1d/0x20 kernel/locking/irqflag-debug.c:10
Hardware initialization for the rtl8188cu can run for as long as 350 ms,
and the routine may be called with interrupts disabled. To avoid locking
the machine for this long, the current routine saves the interrupt flags
and enables local interrupts. The problem is that it restores the flags
at the end without disabling local interrupts first.
This patch fixes commit a53268be0c ("rtlwifi: rtl8192cu: Fix too long
disable of IRQs").
Reported-by: syzbot+cce1ee31614c171f5595@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Fixes: a53268be0c ("rtlwifi: rtl8192cu: Fix too long disable of IRQs")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211215171105.20623-1-Larry.Finger@lwfinger.net
The A-MPDU TX retransmission rate is always high (> 20%) even in a very
clean environment. However, the vendor driver retransimission rate is
< 10% in the same test bed. The difference is the vendor driver starts
the A-MPDU TXOP with initial RTS/CTS handshake which is observed in the
air capture and the TX descriptor. Since the driver does not know how
many frames will be aggregated and the estimated duration, forcing the
RTS/CTS protection for A-MPDU helps to lower the retransmission rate
from > 20% to ~12% in the same test setup with the vendor driver.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211215085819.729345-1-chris.chiu@canonical.com
These settings enables mac to detect and recover when rx fifo
circuit deadlock occurs. Previous version missed this, so we fix it.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217012708.8623-1-pkshih@realtek.com
Currently all realtek wifi chip is set to check CRC of VHT-SIG-B
in 802.11ac signal, but some AP don't calculate the CRC and packets
from these AP can't be received and lead to disconnection.
We disable the check defaultly to avoid this case.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217012421.7859-1-pkshih@realtek.com
Many Intel based platforms face system random freeze after commit
9e2fd29864 ("rtw88: add napi support").
The commit itself shouldn't be the culprit. My guess is that the 8821CE
only leaves ASPM L1 for a short period when IRQ is raised. Since IRQ is
masked during NAPI polling, the PCIe link stays at L1 and makes RX DMA
extremely slow. Eventually the RX ring becomes messed up:
[ 1133.194697] rtw_8821ce 0000:02:00.0: pci bus timeout, check dma status
Since the 8821CE hardware may fail to leave ASPM L1, manually do it in
the driver to resolve the issue.
Fixes: 9e2fd29864 ("rtw88: add napi support")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=215131
BugLink: https://bugs.launchpad.net/bugs/1927808
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211215114635.333767-1-kai.heng.feng@canonical.com
Move _chk_btc_err and update_bt_cnt to _chk_btc_report(),
so we can update counter/info to COEX at a proper moment,
instead of relying on a user does cat the debug info periodically.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211209083229.10815-6-pkshih@realtek.com
Add function to get and parse BT polluted counter.
When WLAN Tx was dropped by BT, the packet will be marked as BT polluted.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211209083229.10815-4-pkshih@realtek.com
Prevent to send H2C request to FW when BTC is not initialized or
WL is under power saving. Add counter to count the H2C success or fail.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211209083229.10815-3-pkshih@realtek.com
To resolve C2H handle length mismatch, or it will parse the c2h content
out of array.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211209083229.10815-2-pkshih@realtek.com
This is found by Smatch static checker warning:
drivers/net/wireless/realtek/rtw89/mac80211.c:31 rtw89_ops_tx()
error: uninitialized symbol 'qsel'.
The warning is because 'qsel' isn't filled by rtw89_core_tx_write() due to
failed to write. The way to fix it is to avoid kicking off TX DMA, so add
'return' to the failure case.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211201093816.13806-1-pkshih@realtek.com
Originally, cch_by_bw recorded center channels of each available
bandwidths under current bandwidth. And the plan was to iterate
cch_by_bw as parameters to query other configurations. However,
we have not used it for the time being. Keeping it will disturb
the follow-up things, such as bandwidth 160 MHz, so we remove it
for now. If it's really needed at some point, we will redesign it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211201080901.12125-1-pkshih@realtek.com
With wrong rtwsta->mac_id, it can't send out ack properly when we receive
assoc response occasionally. Then, it failed to connect an AP.
The cause is that we store 'sta' and use it somewhere. To correct this,
remove the variable and use mac_id in drv_priv of 'sta' or 'vif' passed
by mac80211.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211201080607.11211-1-pkshih@realtek.com
Show channel and bandwidth in debugfs tx_pwr_tbl to make it easier
to understand which tx power table is shown currently, and to reduce
additional checks through other ways.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211129020626.6384-1-pkshih@realtek.com
It is useful to fix the bit rate of TX packets. For example, if
someone is measuring the TX power, or debugging with the issues
of the TX throughput on the field.
To set the value of fixed rate, one should input corresponding
desc rate index (ex, 0x0b for DESC_RATE54M to fix at 54 Mbps).
Set a value larger than DESC_RATE_MAX will disable fix rate, so
the rate adaptive mechanism can resume to work.
Example,
To fix rate at MCS 1:
echo 0x0d > /sys/kernel/debug/ieee80211/phy0/rtw88/fix_rate
To not to fix rate:
echo 0xff > /sys/kernel/debug/ieee80211/phy0/rtw88/fix_rate
To know which rate was fixed at:
cat /sys/kernel/debug/ieee80211/phy0/rtw88/fix_rate
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211129020506.6273-1-pkshih@realtek.com
We used to fill in rx skbs' frequency field by mac80211's current
channel value. In some cases, mac80211 switches channel before all
rx packets have been processed. This results in incorrect bss info.
We fix this by filling in frequency field with channel index obtained
from hardware, then fix potential cck missing issue by skb's original
hw rate. After all fix is done, convert hw rate back to the supported
band rate index.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211111023706.14154-3-pkshih@realtek.com
In order to use compiler to check if we do improper cast of const* on
arguments of inline function.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211119054512.10620-4-pkshih@realtek.com
Add 'const' to be clear that this is a read-only access, and this patch
doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211119054512.10620-3-pkshih@realtek.com
First set of patches for v5.17. The biggest change is the iwlmei
driver for Intel's AMT devices. Also now WCN6855 support in ath11k
should be usable.
Major changes:
ath10k
* fetch (pre-)calibration data via nvmem subsystem
ath11k
* enable 802.11 power save mode in station mode for qca6390 and wcn6855
* trace log support
* proper board file detection for WCN6855 based on PCI ids
* BSS color change support
rtw88
* add debugfs file to force lowest basic rate
* add quirk to disable PCI ASPM on HP 250 G7 Notebook PC
mwifiex
* add quirk to disable deep sleep with certain hardware revision in
Surface Book 2 devices
iwlwifi
* add iwlmei driver for co-operating with Intel's Active Management
Technology (AMT) devices
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmGvclcRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZtK6wgAoOoT83JKMreXlXXhVegqlJbC3HyElF5r
DJlpDDJkJUT9airol2nd0yFfP+5WFyQPrt5shsQmqz43U4jlgfFpFXZIjQufK+gn
VAGvVGfsanRXEFlsVgFZeSZvAEyEyNSggxADC03Ky0xtiCGc89r2o71jD3HA/ZzO
1X8gbKH7YLWj4G/GQkrKsvIAwzoZXT7nwQSdW73M8QVzk4OSNhLBLdiqKYq0yViM
7Ea2Vj27hiyk/RXNUZHy+bKa8vKN5sA91VHJ836aPZBQ4OLotGzF3AgHfgIhIpdr
hI4BVJbngpjQho1EkCnZZuISPes0YQWJB5hK5xpL98yuIL4wyJRfeQ==
=I8Dj
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
First set of patches for v5.17. The biggest change is the iwlmei
driver for Intel's AMT devices. Also now WCN6855 support in ath11k
should be usable.
Major changes:
ath10k
* fetch (pre-)calibration data via nvmem subsystem
ath11k
* enable 802.11 power save mode in station mode for qca6390 and wcn6855
* trace log support
* proper board file detection for WCN6855 based on PCI ids
* BSS color change support
rtw88
* add debugfs file to force lowest basic rate
* add quirk to disable PCI ASPM on HP 250 G7 Notebook PC
mwifiex
* add quirk to disable deep sleep with certain hardware revision in
Surface Book 2 devices
iwlwifi
* add iwlmei driver for co-operating with Intel's Active Management
Technology (AMT) devices
* tag 'wireless-drivers-next-2021-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (87 commits)
iwlwifi: mei: fix linking when tracing is not enabled
rtlwifi: rtl8192de: Style clean-ups
mwl8k: Use named struct for memcpy() region
intersil: Use struct_group() for memcpy() region
libertas_tf: Use struct_group() for memcpy() region
libertas: Use struct_group() for memcpy() region
wlcore: no need to initialise statics to false
rsi: Fix out-of-bounds read in rsi_read_pkt()
rsi: Fix use-after-free in rsi_rx_done_handler()
brcmfmac: Configure keep-alive packet on suspend
wilc1000: remove '-Wunused-but-set-variable' warning in chip_wakeup()
iwlwifi: mvm: read the rfkill state and feed it to iwlmei
iwlwifi: mvm: add vendor commands needed for iwlmei
iwlwifi: integrate with iwlmei
iwlwifi: mei: add debugfs hooks
iwlwifi: mei: add the driver to allow cooperation with CSME
mei: bus: add client dma interface
mwifiex: Ignore BTCOEX events from the 88W8897 firmware
mwifiex: Ensure the version string from the firmware is 0-terminated
mwifiex: Add quirk to disable deep sleep with certain hardware revision
...
====================
Link: https://lore.kernel.org/r/20211207144211.A9949C341C1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
8821CE causes random freezes on HP 250 G7 Notebook PC. Add a quirk
to disable pci ASPM capability.
Reported-by: rtl8821cerfe2 <rtl8821cerfe2@protonmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211119052437.8671-1-pkshih@realtek.com
The management frame with high rate e.g. 24M may not be transmitted
smoothly in long range environment.
Add a debugfs to force to use the lowest basic rate
in order to debug the reachability of transmitting management frame.
obtain current setting
cat /sys/kernel/debug/ieee80211/phyX/rtw88/force_lowest_basic_rate
force lowest rate:
echo 1 > /sys/kernel/debug/ieee80211/phyX/rtw88/force_lowest_basic_rate
Signed-off-by: Yu-Yen Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211102022454.10944-2-pkshih@realtek.com
By default the driver uses the 1M and 6M rate for managemnt frames
in 2G and 5G bands respectively. But when the basic rates is
configured from the mac80211, we need to send the management frames
according to the basic rates.
This commit makes the driver use the lowest basic rates to send
the management frames.
Signed-off-by: Yu-Yen Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211102022454.10944-1-pkshih@realtek.com
The AXIDMA is tx/rx packet transmission between PCIE host
and device, and TX FIFO is MAC TX data.
We dump them to verify that these memory buffers are correct.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211122021129.4339-1-pkshih@realtek.com
The RF register array is used to help firmware to restore RF settings.
The original code can potentially access out of range, if the size is
between (RTW89_H2C_RF_PAGE_SIZE * RTW89_H2C_RF_PAGE_NUM + 1) to
((RTW89_H2C_RF_PAGE_SIZE + 1) * RTW89_H2C_RF_PAGE_NUM). Fortunately,
current used size doesn't fall into the wrong case, and the size will not
change if we don't update RF parameter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211119055729.12826-1-pkshih@realtek.com
Fix the following coccicheck review:
./drivers/net/wireless/realtek/rtw89/mac.c: 1096: 5-8: Unneeded variable
Remove unneeded variable used to store return value.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211110121135.151187-1-deng.changcheng@zte.com.cn
The conditional operator is unnecessary while assigning values to the
bool variables.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211104061119.1685-1-ye.guojin@zte.com.cn
Start to configure entries with RTW89_QATAR, RTW89_UKRAINE, RTW89_CN.
Adjust some entries with explicit rtw89_regulatory instead of RTW89_WW.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211101093106.28848-5-pkshih@realtek.com
Update tx power limit table and tx power limit_ru table to R54.
Configure entries for MEXICO, CN, QATAR, and adjust some values
of original entries.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211101093106.28848-4-pkshih@realtek.com
Support QATAR in rtw89_regulation_type and reorder the enum to align
realtek R58-R31 regulation definition. Besides, if an unassigned entry
of limit/limit_ru tables is read, return the corresponding WW value for
the unconfigured case.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211101093106.28848-3-pkshih@realtek.com
This modification just replaces the number filled in the regd field
with the corresponding enum. No assignment of a value in a table is
changed. Doing this first is because the follow-up patches may adjust
the order of enum declarations.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211101093106.28848-2-pkshih@realtek.com
The partition size is used to tell hardware the size of piece we are going
to send a firmware. The old code updates the size in constant buffer of
firmware, and leads system crash.
To fix this, update the size on skb->data after we copy the firmware data
into skb.
Buglink: https://bugzilla.opensuse.org/show_bug.cgi?id=1188303
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211119054512.10620-2-pkshih@realtek.com
The pointer rtwsta is dereferencing pointer sta before sta is being null
checked. Fix this by assigning sta->drv_priv to rtwsta only if sta is not
NULL, otherwise just NULL.
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211022061242.8383-1-pkshih@realtek.com
It seems to me when pub_cfg->grp0 + pub_cfg->grp1 != pub_cfg->pub_max is true,
it should return -EFAULT rather than 0. Otherwise, the function doesn't need
to exist.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXEJey8lKksAZif4@ns.kevlo.org
This patch fixes the following Coccinelle warning:
drivers/net/wireless/realtek/rtw89/rtw8852a.c:753:
WARNING possible condition with no effect (if == else)
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211021042035.1042463-1-lv.ruyi@zte.com.cn
Fix the return value check which testing the wrong variable
in rtw89_cam_send_sec_key_cmd().
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018033102.1813058-1-yangyingliang@huawei.com
The function rtw89_mac_enable_bb_rf is a void return type, so there is
no return error code to ret, so the following check for an error in ret
is redundant dead code and can be removed.
Addresses-Coverity: ("Logically dead code")
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015152113.33179-1-colin.king@canonical.com
There are two spelling mistakes in rtw89_debug messages. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015105004.11817-1-colin.king@canonical.com
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/0855d51423578ad019c0264dad3fe47a2e8af9c7.1633849511.git.christophe.jaillet@wanadoo.fr
The variable version is being initialized with a value that is
never read, it is being updated afterwards in both branches of
an if statement. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211007163722.20165-1-colin.king@canonical.com
This driver named rtw89, which is the next generation of rtw88, supports
Realtek 8852AE 802.11ax 2x2 chip whose new features are OFDMA, DBCC,
Spatial reuse, TWT and BSS coloring; now some of them aren't implemented
though.
The chip architecture is entirely different from the chips supported by
rtw88 like RTL8822CE 802.11ac chip. First of all, register address ranges
are totally redefined, so it's impossible to reuse register definition. To
communicate with firmware, new H2C/C2H format is proposed. In order to have
better utilization, TX DMA flow is changed to two stages DMA. To provide
rich RX status information, additional RX PPDU packets are added.
Since there are so many differences mentioned above, we decide to propose
a new driver. It has many authors, they are listed in alphabetic order:
Chin-Yen Lee <timlee@realtek.com>
Ping-Ke Shih <pkshih@realtek.com>
Po Hao Huang <phhuang@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Vincent Fann <vincent_fann@realtek.com>
Yan-Hsuan Chuang <tony0620emma@gmail.com>
Zong-Zhe Yang <kevin_yang@realtek.com>
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211008035627.19463-1-pkshih@realtek.com
According to the Realtek propritary driver and the rtw88 driver, the
tx rates of the ack (includes block ack) are initialized with lower
tx rates (no HT rates) which is set by the RRSR register value. In
real cases, ack rate higher than current tx rate could lead to
difficulty for the receiving end to receive management/control frames.
The retransmission rate would be higher then expected when the driver
is acting as receiver and the RSSI is not good.
Cross out higer rates for ack packet before implementing dynamic rrsr
configuration like the commit 4830872685 ("rtw88: add dynamic rrsr
configuration").
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211001040044.1028708-1-chris.chiu@canonical.com
The usage of fw_crash debugfs is to write 1 to it to trigger fw crash
simulation and to read from it to check the state. When zero is read,
it is supposed to mean fw crash/restart process is done. Then, some
test plans can be designed for crash/restart.
e.g.
step 1. trigger fw crash simulation
step 2. poll the state until zero is read
step 3. check connection by ping test
However, in certain connection cases, triggering fw crash simulation
will take a while. If the state is queried too early before restart
begins processing, it may mistakenly think restart process has been
done. If some tests are started at this time, something unexpected
might happen due to the follow-up restart process.
To avoid that, let fw_crash also show non-zero when a simulation
is still triggering.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211001082301.4805-1-pkshih@realtek.com
When fw fifo dumps, RX clock gating should be disabled to avoid
something unexpected. However, the register operation ran into
a mistake. So, we fix it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210927111830.5354-1-pkshih@realtek.com
