IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
It can be useful to delay setting the nowayout feature for a watchdog
device. Moreover, not every driver (notably gpio_wdt) implements a
nowayout module parameter/otherwise respects CONFIG_WATCHDOG_NOWAYOUT,
and modifying those drivers carries a risk of causing a regression for
someone who has two watchdog devices, sets CONFIG_WATCHDOG_NOWAYOUT
and somehow relies on the gpio_wdt driver being ignorant of
that (i.e., allowing one to gracefully close a gpio_wdt but not the
other watchdog in the system).
So instead, simply make the nowayout sysfs file writable. Obviously,
setting nowayout is a one-way street.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191105205118.11359-1-linux@rasmusvillemoes.dk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
When PREEMPT_RT is enabled, all hrtimer expiry functions are
deferred for execution into the context of ksoftirqd unless otherwise
annotated.
Deferring the expiry of the hrtimer used by the watchdog core, however,
is a waste, as the callback does nothing but queue a kthread work item
and wakeup watchdogd.
It's worst then that, too: the deferral through ksoftirqd also means
that for correct behavior a user must adjust the scheduling parameters
of both watchdogd _and_ ksoftirqd, which is unnecessary and has other
side effects (like causing unrelated expiry functions to execute at
potentially elevated priority).
Instead, mark the hrtimer used by the watchdog core as being _HARD to
allow it's execution directly from hardirq context. The work done in
this expiry function is well-bounded and minimal.
A user still must adjust the scheduling parameters of the watchdogd
to be correct w.r.t. their application needs.
Link: https://lkml.kernel.org/r/0e02d8327aeca344096c246713033887bc490dd7.1538089180.git.julia@ni.com
Cc: Guenter Roeck <linux@roeck-us.net>
Reported-and-tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Reported-by: Tim Sander <tim@krieglstein.org>
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
[bigeasy: use only HRTIMER_MODE_REL_HARD]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191105144506.clyadjbvnn7b7b2m@linutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use definitions instead of magic values in order to improve readability.
Since the CLK field of the WDOG CS register is composed of two bits
to select the watchdog clock source, use a shift representation
instead of BIT().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191029174037.25381-5-festevam@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Compiler is smart enough and knows when to inline, so there
is no need to mark some of these functions as 'inline'.
Remove such annotations.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191029174037.25381-4-festevam@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The 'notifier_block' structure member is unused, so just remove it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191029174037.25381-3-festevam@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
It is more natural to pass the watchdog instance inside
imx7ulp_wdt_enable() instead of the base address.
This also has the benefit to reduce the code a bit.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191029174037.25381-2-festevam@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The function documentation for the exported ROHM BD70528 WDG control
functions used old argument names. Fix the names.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191010060733.GA9979@localhost.localdomain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The struct cdev is embedded in the struct watchdog_core_data. In the
current code, we manage the watchdog_core_data with a kref, but the
cdev is manged by a kobject. There is no any relationship between
this kref and kobject. So it is possible that the watchdog_core_data is
freed before the cdev is entirely released. We can easily get the
following call trace with CONFIG_DEBUG_KOBJECT_RELEASE and
CONFIG_DEBUG_OBJECTS_TIMERS enabled.
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x38
WARNING: CPU: 23 PID: 1028 at lib/debugobjects.c:481 debug_print_object+0xb0/0xf0
Modules linked in: softdog(-) deflate ctr twofish_generic twofish_common camellia_generic serpent_generic blowfish_generic blowfish_common cast5_generic cast_common cmac xcbc af_key sch_fq_codel openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4
CPU: 23 PID: 1028 Comm: modprobe Not tainted 5.3.0-next-20190924-yoctodev-standard+ #180
Hardware name: Marvell OcteonTX CN96XX board (DT)
pstate: 00400009 (nzcv daif +PAN -UAO)
pc : debug_print_object+0xb0/0xf0
lr : debug_print_object+0xb0/0xf0
sp : ffff80001cbcfc70
x29: ffff80001cbcfc70 x28: ffff800010ea2128
x27: ffff800010bad000 x26: 0000000000000000
x25: ffff80001103c640 x24: ffff80001107b268
x23: ffff800010bad9e8 x22: ffff800010ea2128
x21: ffff000bc2c62af8 x20: ffff80001103c600
x19: ffff800010e867d8 x18: 0000000000000060
x17: 0000000000000000 x16: 0000000000000000
x15: ffff000bd7240470 x14: 6e6968207473696c
x13: 5f72656d6974203a x12: 6570797420746365
x11: 6a626f2029302065 x10: 7461747320657669
x9 : 7463612820657669 x8 : 3378302f3078302b
x7 : 0000000000001d7a x6 : ffff800010fd5889
x5 : 0000000000000000 x4 : 0000000000000000
x3 : 0000000000000000 x2 : ffff000bff948548
x1 : 276a1c9e1edc2300 x0 : 0000000000000000
Call trace:
debug_print_object+0xb0/0xf0
debug_check_no_obj_freed+0x1e8/0x210
kfree+0x1b8/0x368
watchdog_cdev_unregister+0x88/0xc8
watchdog_dev_unregister+0x38/0x48
watchdog_unregister_device+0xa8/0x100
softdog_exit+0x18/0xfec4 [softdog]
__arm64_sys_delete_module+0x174/0x200
el0_svc_handler+0xd0/0x1c8
el0_svc+0x8/0xc
This is a common issue when using cdev embedded in a struct.
Fortunately, we already have a mechanism to solve this kind of issue.
Please see commit 233ed09d7f ("chardev: add helper function to
register char devs with a struct device") for more detail.
In this patch, we choose to embed the struct device into the
watchdog_core_data, and use the API provided by the commit 233ed09d7f
to make sure that the release of watchdog_core_data and cdev are
in sequence.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191008112934.29669-1-haokexin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
... by moving the fall through comment outside of the code block so that
gcc sees it.
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190929114649.22740-1-bp@alien8.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Normally, the watchdog is disabled when /dev/watchdog is closed, but if
CONFIG_WATCHDOG_NOWAYOUT is defined, then it means that the watchdog should
remain enabled. So we should keep it enabled if CONFIG_WATCHDOG_NOWAYOUT
is defined.
Reported-by: Razvan Becheriu <razvan.becheriu@qualitance.com>
Cc: Ferry Toth <fntoth@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Razvan Becheriu <razvan.becheriu@gmail.com>
Link: https://lore.kernel.org/r/20190924143116.69823-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use __maybe_unused for power management related functions instead
of #if CONFIG_PM_SLEEP to simply the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1569308828-8320-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The watchdog controller on NCT6116D is compatible with NCT6102D.
Extend the support to enable SuperIO based NCT6116D watchdog device.
Signed-off-by: Srikanth Krishnakar <Srikanth_Krishnakar@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190918160458.10108-1-Srikanth_Krishnakar@mentor.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The bd70528 watchdog driver is probed by MFD driver. Add MODULE_ALIAS
in order to allow udev to load the module when MFD sub-device cell for
watchdog is added.
Fixes: bbc88a0ec9 ("watchdog: bd70528: Initial support for ROHM BD70528 watchdog block")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
SCU firmware calculates pretimeout based on current time stamp
instead of watchdog timeout stamp, need to convert the pretimeout
to SCU firmware's timeout value.
Fixes: 15f7d7fc55 ("watchdog: imx_sc: Add pretimeout support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The left time value is wrong when we get it by sysfs. The left time value
should be equal to preset timeout value minus elapsed time value. According
to the Meson-GXB/GXL datasheets which can be found at [0], the timeout value
is saved to BIT[0-15] of the WATCHDOG_TCNT, and elapsed time value is saved
to BIT[16-31] of the WATCHDOG_TCNT.
[0]: http://linux-meson.com
Fixes: 683fa50f0e ("watchdog: Add Meson GXBB Watchdog Driver")
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
When an IRQ is present in the dts, the probe function shall fail if
the interrupt can not be registered.
The probe function shall also be retried if getting the irq is being
deferred.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The compat_ptr_ioctl() infrastructure did not make it into
linux-5.4, so cpwd now fails to build.
Fix it by using an open-coded version.
Fixes: 68f28b01fb ("watchdog: cpwd: use generic compat_ptr_ioctl")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAl2NtDQACgkQ+iyteGJfRsoHgQCdGLeQMm4IR3jsDdFQk/eTIGfR
eNIAoN8AY1UTFvWJTxEOhucdAzEAVnHs
=TdeQ
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-5.4-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- addition of AST2600, i.MX7ULP and F81803 watchdog support
- removal of the w90x900 and ks8695 drivers
- ziirave_wdt improvements
- small fixes and improvements
* tag 'linux-watchdog-5.4-rc1' of git://www.linux-watchdog.org/linux-watchdog: (51 commits)
watchdog: f71808e_wdt: Add F81803 support
watchdog: qcom: remove unnecessary variable from private storage
watchdog: qcom: support pre-timeout when the bark irq is available
watchdog: imx_sc: this patch just fixes whitespaces
watchdog: apseed: Add access_cs0 option for alt-boot
watchdog: aspeed: add support for dual boot
watchdog: orion_wdt: use timer1 as a pretimeout
watchdog: Add i.MX7ULP watchdog support
dt-bindings: watchdog: Add i.MX7ULP bindings
dt-bindings: watchdog: sun4i: Add the watchdog clock
dt-bindings: watchdog: sun4i: Add the watchdog interrupts
dt-bindings: watchdog: Convert Allwinner watchdog to a schema
dt-bindings: watchdog: Add YAML schemas for the generic watchdog bindings
watchdog: aspeed: Add support for AST2600
dt-bindings: watchdog: Add ast2600 compatible
watchdog: ziirave_wdt: Update checked I2C functionality mask
watchdog: ziirave_wdt: Drop ziirave_firm_write_block_data()
watchdog: ziirave_wdt: Fix DOWNLOAD_START payload
watchdog: ziirave_wdt: Drop status polling code
watchdog: ziirave_wdt: Fix RESET_PROCESSOR payload
...
Pull i2c updates from Wolfram Sang:
- new driver for ICY, an Amiga Zorro card :)
- axxia driver gained slave mode support, NXP driver gained ACPI
- the slave EEPROM backend gained 16 bit address support
- and lots of regular driver updates and reworks
* 'i2c/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
i2c: tegra: Move suspend handling to NOIRQ phase
i2c: imx: ACPI support for NXP i2c controller
i2c: uniphier(-f): remove all dev_dbg()
i2c: uniphier(-f): use devm_platform_ioremap_resource()
i2c: slave-eeprom: Add comment about address handling
i2c: exynos5: Remove IRQF_ONESHOT
i2c: stm32f7: Make structure stm32f7_i2c_algo constant
i2c: cht-wc: drop check because i2c_unregister_device() is NULL safe
i2c-eeprom_slave: Add support for more eeprom models
i2c: fsi: Add of_put_node() before break
i2c: synquacer: Make synquacer_i2c_ops constant
i2c: hix5hd2: Remove IRQF_ONESHOT
i2c: i801: Use iTCO version 6 in Cannon Lake PCH and beyond
watchdog: iTCO: Add support for Cannon Lake PCH iTCO
i2c: iproc: Make bcm_iproc_i2c_quirks constant
i2c: iproc: Add full name of devicetree node to adapter name
i2c: piix4: Add ACPI support
i2c: piix4: Fix probing of reserved ports on AMD Family 16h Model 30h
i2c: ocores: use request_any_context_irq() to register IRQ handler
i2c: designware: Fix optional reset error handling
...
This adds watchdog support for the Fintek F81803 Super I/O chip.
Testing was done on the Seneca XK-QUAD.
Signed-off-by: Jaret Cantu <jaret.cantu@timesys.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190912175550.9340-1-jaret.cantu@timesys.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
there is no need to continue keeping the clock in private storage.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190906205411.31666-3-jorge.ramirez-ortiz@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the bark interrupt as the pre-timeout notifier whenever this
interrupt is available.
By default, the pretimeout notification shall occur one second earlier
than the timeout.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190906205411.31666-2-jorge.ramirez-ortiz@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Set WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION into WDT_CLEAR_TIMEOUT_STATUS
to clear out boot code source and re-enable access to the primary SPI flash
chip while booted via wdt2 from the alternate chip.
AST2400 datasheet says:
"In the 2nd flash booting mode, all the address mapping to CS0# would be
re-directed to CS1#. And CS0# is not accessible under this mode. To access
CS0#, firmware should clear the 2nd boot mode register in the WDT2 status
register WDT30.bit[1]."
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190828102402.13155-4-i.mikhaylov@yadro.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The orion watchdog can either reset the CPU or generate an interrupt.
The interrupt would be useful for debugging as it provides panic()
output about the watchdog expiry, however if the interrupt is used the
watchdog can't reset the CPU in the event of being stuck in a loop with
interrupts disabled or if the CPU is prevented from accessing memory
(e.g. an unterminated DMA).
The Armada SoCs have spare timers that aren't currently used by the
Linux kernel. We can use timer1 to provide a pre-timeout ahead of the
watchdog timer and provide the possibility of gathering debug before the
reset triggers.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190829215224.27956-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The i.MX7ULP Watchdog Timer (WDOG) module is an independent timer
that is available for system use.
It provides a safety feature to ensure that software is executing
as planned and that the CPU is not stuck in an infinite loop or
executing unintended code. If the WDOG module is not serviced
(refreshed) within a certain period, it resets the MCU.
Add driver support for i.MX7ULP watchdog.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1566999303-18795-2-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The ast2600 can be supported by the same code as the ast2500.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190819051738.17370-3-joel@jms.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
There's only one user of ziirave_firm_write_block_data(), so we may as
well inline it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-22-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Bootloader firmware expects the following traffic for DOWNLOAD_END:
S Addr Wr [A] 0x10 [A] P
using ziirave_firm_write_byte() will result in
S Addr Wr [A] 0x10 [A] 0x01 [A] 0x01 [A] P
which happens to work because firmware will ignore any extra bytes
sent. Fix this by converting the code to use i2c_smbus_write_byte()
instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-21-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Bootloader firmware doesn't implement DOWNLOAD_START or
DOWNLOAD_PACKET in a non-blocking way. It will stretch the clock of
the first status byte read until the operation is complete. Polling
for the status is not really necessary since it will always succed on
the first try. Replace polling code with a simple single byte read to
simplify things.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-20-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Bootloader firmware expects the following traffic for
RESET_PROCESSOR:
S Addr Wr [A] 0x0b [A] 0x01 [A] P
using ziirave_firm_write_byte() will result in
S Addr Wr [A] 0x0b [A] 0x01 [A] 0x01 [A] P
which happens to work because firmware will ignore any extra bytes and
expected magic value matches byte count sent by
i2c_smbus_write_block_data(). Fix this by converting the code to use
i2c_smbus_write_byte_data() instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-19-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Bootloader firmware expects the following traffic for DOWNLOAD_END:
S Addr Wr [A] 0x11 [A] P
using ziirave_firm_write_byte() will result in
S Addr Wr [A] 0x11 [A] 0x01 [A] 0x01 [A] P
which happens to work because firmware will ignore any extra bytes
sent. Fix this by converting the code to use i2c_smbus_write_byte()
instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-18-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Bootloader firmware expects the following traffic for
JUMP_TO_BOOTLOADER:
S Addr Wr [A] 0x0c [A] 0x01 [A] P
using ziirave_firm_write_byte() will result in
S Addr Wr [A] 0x0c [A] 0x01 [A] 0x01 [A] P
which happens to work because firmware will ignore any extra bytes and
expected magic value matches byte count sent by
i2c_smbus_write_block_data(). Fix this by converting the code to use
i2c_smbus_write_byte_data() instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-17-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Fix misleading error message in ziirave_wdt_init_duration(). Saying
"unable to set ..." implies that an attempt at communication with
watchdog device has taken palce and was not successful. In this case,
however, all it indicates is that no reset pulse duration was
specified either via kernel parameter or Device Tree. Re-phase the log
message to be more clear about benign nature of this event.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-16-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Bootloader code will ignore any attempts to write data to any flash
area outside of [ZIIRAVE_FIRM_FLASH_MEMORY_START;
ZIIRAVE_FIRM_FLASH_MEMORY_END]. Firmware update code already have an
appropriate check to skip those areas when validating updated
firmware. Firmware programming code, OTOH, does not and will
needlessly send no-op I2C traffic. Add an appropriate check to
__ziirave_firm_write_pkt() so as to save all of that wasted effort.
While at it, normalize all of the address handling code to use full
32-bit address in units of bytes and convert it to an appropriate
value only in places where that is necessary.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-15-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
We only compare first 'len' bytes of read firmware, so we don't need
to read more that that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-14-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Ihex_next_binrec() will return NULL if next record's 'len' is zero, so
explicit checks for that in the driver are unnecessary. Drop them.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-13-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Instead of doing this explicitly use put_unaligned_le16() to place
16-bit address value into command payload.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-12-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Instead of zeroing out all of the packet and then overwriting a
significant portion of those zeros via memcpy(), zero out only a
portion of the packet that is known to not contain any data.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-11-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Both memset() and ziirave_firm_write_block_data() expect length in
bytes as an argument, not a number of elements in array. It just
happens that in this particular case both values are equal. Modify the
code to use sizeof() instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-10-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Zeros don't contribute anything to checksum value, so we can skip
unused portion of the packet when calculating its checksum.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-9-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
We don't need to check for packet length more than once, so drop the
extra check in ziirave_firm_upload(). While at it move the check at
the very start of __ziirave_firm_write_pkt(), as to not waste any time
preparing a packet we'll never use.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-8-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
There no reason why ziirave_firm_write_pkt() has to take firmware
data via 'struct ihex_binrec' and it can just take address, data pointer
and data length as individual arguments. Make this change to allow us
to drastically simplify handling page crossing case by removing all of
the extra code required to split 'struct ihex_binrec' into two.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-7-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Log bootloader/firmware info during probe. This information is
available via sysfs already, but it's really helpful to have this in
kernel log during startup as well.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-6-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Reprogramming bootloader on watchdog MCU will result in reported
default timeout value of "0". That in turn will be unnecessarily
rejected by the driver as invalid device (-ENODEV). Simplify probe to
read stored timeout value, set it to a sane default if it is bogus,
and then program that value unconditionally.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-5-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
