IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Add an encoder hook, which can be called on enabled TC ports to
determine if the port uses a TBT or a non-TBT PLL. An upcoming patch
will use this to sanity check active TC port's PHY state wrt. the PLL
type used by the port.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-13-imre.deak@intel.com
Since an HDMI output can only be enabled in legacy mode on TC ports,
assume that VBT is wrong and the port is legacy if VBT says the port is
non-legacy and has HDMI. If VBT says to enable DP as well leave the
non-legacy flag enabled, relying on the flag getting fixed up based on
the HPD status during sink detection.
v2: Fix the legacy port flag only if DP is not enabled.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-1-imre.deak@intel.com
For consistency detect the initial TC mode in the PHY owned state the
same way this is done in the not owned state (w/o changing the
behavior). While at it, add more details to the PHY state debug print.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-11-imre.deak@intel.com
Atm, a TC port's initial mode will be read out as TBT mode in any case
the PHY ownership is not held. This isn't correct for legacy ports which
should be used only in legacy mode.
Fix the above initial mode to be disconnected mode for a legacy port and
TBT mode for DP-alt/TBT ports. Determine the port type by checking first
the HPD state and then the legacy VBT flag (so the HPD state can correct
a bogus VBT flag). If a sink is connected on a disabled port the PHY
will get also connected (switching it to legacy mode on a legacy port).
Also connect the PHY on a legacy port if it's enabled but BIOS
incorrectly left it in the disconnected state for some reason.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-10-imre.deak@intel.com
A legacy TC port can't be switched to TBT mode, even if the PHY
initialization wasn't ready yet for some reason, so prevent this.
This shouldn't normally happen as the driver waits for the IOM/TCSS
PHY initialization during driver loading and system resume.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-9-imre.deak@intel.com
Atm, the target TC mode - which the PHY should be switched to at any
point it's used - is TBT in case there is no sink connected. However
legacy ports are only used in the legacy mode regardless of the sink
connected state. Fix the mode returned by
intel_tc_port_get_target_mode() accordingly.
Despite of the above issue, the PHY got disconnected as expected in
response to a sink disconnect event, causing only a redundant
PHY disconnect->reconnect sequence whenever the port was used.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-8-imre.deak@intel.com
During boot-up/system resume, the TC PHY on legacy ports will be
initialized by the IOM/TCSS firmware regardless of a sink being
connected or not (as opposed to DP-alt/TBT ports, which the FW only
inits once a sink is connected).
Wait for the above initialization to complete during HW readout, so that
connecting the PHY later will already see the expected PHY ready state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-6-imre.deak@intel.com
At least restoring the MST topology during system resume needs to use
AUX before the display HW readout->sanitization sequence is complete,
but on TC ports the PHY may be in the wrong mode for this, resulting in
the AUX transfers to fail.
The initial TC port mode is kept fixed as BIOS left it for the above HW
readout sequence (to prevent changing the mode on an enabled port). If
the port is disabled this initial mode is TBT - as in any case the PHY
ownership is not held - even if a DP-alt sink is connected. Thus, the
AUX transfers during this time will use TBT mode instead of the expected
DP-alt mode and so time out.
Fix the above by connecting the PHY during port initialization if the
port is disabled, which will switch to the expected mode (DP-alt in the
above case).
As the encoder/pipe HW state isn't read-out yet at this point, check if
the port is enabled based on the DDI_BUF enabled flag. Save the read-out
initial mode, so intel_tc_port_sanitize_mode() can check this wrt. the
read-out encoder HW state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-5-imre.deak@intel.com
The commit renaming icl_tc_phy_is_in_safe_mode() to
icl_tc_phy_take_ownership() didn't flip the function's return value
accordingly, fix this up.
This didn't cause an actual problem besides state check errors, since
the function is only used during HW readout.
Cc: José Roberto de Souza <jose.souza@intel.com>
Fixes: f53979d68a77 ("drm/i915/display/tc: Rename safe_mode functions ownership")
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-4-imre.deak@intel.com
An enabled TC MST port holds one TC port link reference, regardless of
the number of enabled streams on it, but the TC port HW readout takes
one reference for each active MST stream.
Fix the HW readout, taking only one reference for MST ports.
This didn't cause an actual problem, since the encoder HW readout doesn't
yet support reading out the MST HW state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-3-imre.deak@intel.com
On TC ports the 4ms AUX timeout combined with the 5 * 32 retry
attempts during DPCD accesses adds a 640ms delay to each access if the
sink is disconnected. This in turn slows down a modeset during which the
sink is disconnected (for instance a disabling modeset).
Prevent the above delay by aborting AUX transfers on a TC port with a
disconnected sink.
The DP 1.4a link CTS (4.2.1.5 Source Device Inactive HPD / Inactive AUX
Test") also requires not to initiate AUX transfers on disconnected DP
ports in general, however this patch doesn't change the behavior on
non-TC ports, leaving that for a follow-up.
Reported-and-tested-by: Chris Chiu <chris.chiu@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8279
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-2-imre.deak@intel.com
Rename symbols to match the style of other fbdev-emulation source
code. No functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-9-tzimmermann@suse.de
Consolidate all handling of CONFIG_DRM_FBDEV_LEAK_PHYS_SMEM by
making the module parameter optional in drm_fb_helper.c.
Without the config option, modules can set smem_start in struct
fb_info for internal usage, but not export if to userspace. The
address can only be exported by enabling the option and setting
the module parameter. Also update the comment.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng<suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-8-tzimmermann@suse.de
Clean up fbdev and client state if the probe function fails. It
used to leak allocated resources. Also reorder the individual steps
to simplify cleanup.
v2:
* move screen_size update into separate patches
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-7-tzimmermann@suse.de
The size of the screen memory should be equivalent to the size of
the screen's GEM buffer. Don't recalculate the value.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-6-tzimmermann@suse.de
The size of the framebuffer can either be stored in screen_info or
smem_len. Take both into account in the deferred I/O code.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-5-tzimmermann@suse.de
Export the fb_info release code as drm_fb_helper_release_info(). Will
help with cleaning up failed fbdev probing.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng<suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-4-tzimmermann@suse.de
Remove the flag prefer_shadow_fbdev from struct drm_mode_config.
Drivers set this flag to enable shadow buffering in the generic
fbdev emulation. Such shadow buffering is now mandatory, so the
flag is unused.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-3-tzimmermann@suse.de
Remove all codepaths that implement fbdev output directly on GEM
buffers. Always allocate a shadow buffer in system memory and set
up deferred I/O for mmap.
The fbdev code that operated directly on GEM buffers was used by
drivers based on GEM DMA helpers. Those drivers have been migrated
to use fbdev-dma, a dedicated fbdev emulation for DMA memory. All
remaining users of fbdev-generic require shadow buffering.
Memory management of the remaining callers uses TTM, GEM SHMEM
helpers or a variant of GEM DMA helpers that is incompatible with
fbdev-dma. Therefore remove the unused codepaths from fbdev-generic
and simplify the code.
Using a shadow buffer with deferred I/O is probably the best case
for most remaining callers. Some of the TTM-based drivers might
benefit from a dedicated fbdev emulation that operates directly on
the driver's video memory.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-2-tzimmermann@suse.de
Replace the open-code with dev_err_probe() to simplify the code.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/202303221622511915615@zte.com.cn
Replace the open-code with dev_err_probe() to simplify the code.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/202303221621336645576@zte.com.cn
- uAPI changes:
- Add opcodes to the CS ioctl to allow user to stall/resume specific engines
inside Gaudi2. This is to allow the user to perform power
testing/measurements when training different topologies.
- Expose in the INFO ioctl the amount of device memory that the driver
and f/w reserve for themselves.
- Expose in the INFO ioctl a bit-mask of the available rotator engines
in Gaudi2. This is to align with other engines that are already exposed.
- Expose in the INFO ioctl the register's address of the f/w that should
be used to trigger interrupts from within the user's code running in the
compute engines.
- Add a critical-event bit in the eventfd bitmask so the user will know the
event that was received was critical, and a reset will now occur
- Expose in the INFO ioctl two new opcodes to fetch information on h/w and
f/w events. The events recorded are the events that were reported in the
eventfd.
- New features and improvements:
- Add a dedicated interrupt ID in MSI-X in the device to the notification of
an unexpected user-related event in Gaudi2. Handle it in the driver by
reporting this event.
- Allow the user to fetch the device memory current usage even when the
device is undergoing compute-reset (a reset type that only clears the
compute engines).
- Enable graceful reset mechanism for compute-reset. This will give the
user a few seconds before the device is reset. For example, the user can,
during that time, perform certain device operations (dump data for debug)
or close the device in an orderly fashion.
- Align the decoder with the rest of the engines in regard to notification
to the user about interrupts and in regard to performing graceful reset
when needed (instead of immediate reset).
- Add support for assert interrupt from the TPC engine.
- Get the reset type that is necessary to perform per event from the
auto-generated irq_map array.
- Print the specific reason why a device is still in use when notifying to
the user about it (after the user closed the device's FD).
- Move to threaded IRQ when handling interrupts of workload completions.
- Firmware related fixes:
- Fix RAZWI event handler to match newest f/w version.
- Read error cause register in dma core events because the f/w doesn't
do that.
- Increase maximum time to wait for completion of Gaudi2 reset due to f/w
bug.
- Align to the latest firmware specs.
- Enforce the release order of the compute device and dma-buf.
i.e increment the device file refcount for any dma-buf that was exported
for that device. This will make sure the compute device release function
won't be called until the user closes all the FDs of the relevant
dma-bufs. Without this change, closing the device's FD before/without
closing the dma-buf's FD would always lead to hard-reset of the device.
- Fix a link in the drm documentation to correctly point to the accel section.
- Compilation warnings cleanups
- Misc bug fixes and code cleanups
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE7TEboABC71LctBLFZR1NuKta54AFAmQYfcAACgkQZR1NuKta
54DB4Af/SuiHZkVXwr+yHPv9El726rz9ZQD7mQtzNmehWGonwAvz15yqocNMUSbF
JbqE/vrZjvbXrP1Uv5UrlRVdnFHSPV18VnHU4BMS/WOm19SsR6vZ0QOXOoa6/AUb
w+kF3D//DbFI4/mTGfpH5/pzwu51ti8aVktosPFlHIa8iI8CB4/4IV+ivQ8UW4oK
HyDRkIvHdRmER7vGOfhwhsr4zdqSlJBYrv3C3Z1dkSYBPW/5ICbiM1UlKycwdYKI
cajQBSdUQwUCWnI+i8RmSy3kjNO6OE4XRUvTv89F2bQeyK/1rJLG2m2xZR/Ml/o5
7Cgvbn0hWZyeqe7OObYiBlSOBSehCA==
=wclm
-----END PGP SIGNATURE-----
Merge tag 'drm-habanalabs-next-2023-03-20' of https://git.kernel.org/pub/scm/linux/kernel/git/ogabbay/linux into drm-next
This tag contains habanalabs driver and accel changes for v6.4:
- uAPI changes:
- Add opcodes to the CS ioctl to allow user to stall/resume specific engines
inside Gaudi2. This is to allow the user to perform power
testing/measurements when training different topologies.
- Expose in the INFO ioctl the amount of device memory that the driver
and f/w reserve for themselves.
- Expose in the INFO ioctl a bit-mask of the available rotator engines
in Gaudi2. This is to align with other engines that are already exposed.
- Expose in the INFO ioctl the register's address of the f/w that should
be used to trigger interrupts from within the user's code running in the
compute engines.
- Add a critical-event bit in the eventfd bitmask so the user will know the
event that was received was critical, and a reset will now occur
- Expose in the INFO ioctl two new opcodes to fetch information on h/w and
f/w events. The events recorded are the events that were reported in the
eventfd.
- New features and improvements:
- Add a dedicated interrupt ID in MSI-X in the device to the notification of
an unexpected user-related event in Gaudi2. Handle it in the driver by
reporting this event.
- Allow the user to fetch the device memory current usage even when the
device is undergoing compute-reset (a reset type that only clears the
compute engines).
- Enable graceful reset mechanism for compute-reset. This will give the
user a few seconds before the device is reset. For example, the user can,
during that time, perform certain device operations (dump data for debug)
or close the device in an orderly fashion.
- Align the decoder with the rest of the engines in regard to notification
to the user about interrupts and in regard to performing graceful reset
when needed (instead of immediate reset).
- Add support for assert interrupt from the TPC engine.
- Get the reset type that is necessary to perform per event from the
auto-generated irq_map array.
- Print the specific reason why a device is still in use when notifying to
the user about it (after the user closed the device's FD).
- Move to threaded IRQ when handling interrupts of workload completions.
- Firmware related fixes:
- Fix RAZWI event handler to match newest f/w version.
- Read error cause register in dma core events because the f/w doesn't
do that.
- Increase maximum time to wait for completion of Gaudi2 reset due to f/w
bug.
- Align to the latest firmware specs.
- Enforce the release order of the compute device and dma-buf.
i.e increment the device file refcount for any dma-buf that was exported
for that device. This will make sure the compute device release function
won't be called until the user closes all the FDs of the relevant
dma-bufs. Without this change, closing the device's FD before/without
closing the dma-buf's FD would always lead to hard-reset of the device.
- Fix a link in the drm documentation to correctly point to the accel section.
- Compilation warnings cleanups
- Misc bug fixes and code cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCgAdFiEE7TEboABC71LctBLFZR1NuKta54AFAmQYfcAACgkQZR1NuKta
# 54DB4Af/SuiHZkVXwr+yHPv9El726rz9ZQD7mQtzNmehWGonwAvz15yqocNMUSbF
# JbqE/vrZjvbXrP1Uv5UrlRVdnFHSPV18VnHU4BMS/WOm19SsR6vZ0QOXOoa6/AUb
# w+kF3D//DbFI4/mTGfpH5/pzwu51ti8aVktosPFlHIa8iI8CB4/4IV+ivQ8UW4oK
# HyDRkIvHdRmER7vGOfhwhsr4zdqSlJBYrv3C3Z1dkSYBPW/5ICbiM1UlKycwdYKI
# cajQBSdUQwUCWnI+i8RmSy3kjNO6OE4XRUvTv89F2bQeyK/1rJLG2m2xZR/Ml/o5
# 7Cgvbn0hWZyeqe7OObYiBlSOBSehCA==
# =wclm
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 21 Mar 2023 01:37:36 AEST
# gpg: using RSA key ED311BA00042EF52DCB412C5651D4DB8AB5AE780
# gpg: Can't check signature: No public key
From: Oded Gabbay <ogabbay@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320154026.GA766126@ogabbay-vm-u20.habana-labs.com
Driver Changes:
- Fix issue #6333: "list_add corruption" and full system lockup from
performance monitoring (Janusz)
- Give the punit time to settle before fatally failing (Aravind, Chris)
- Don't use stolen memory or BAR for ring buffers on LLC platforms (John)
- Add missing ecodes and correct timeline seqno on GuC error captures (John)
- Make sure DSM size has correct 1MiB granularity on Gen12+ (Nirmoy,
Lucas)
- Fix potential SSEU max_subslices array-index-out-of-bounds access on Gen11 (Andrea)
- Whitelist COMMON_SLICE_CHICKEN3 for UMD access on Gen12+ (Matt R.)
- Apply Wa_1408615072/Wa_1407596294 correctly on Gen11 (Matt R)
- Apply LNCF/LBCF workarounds correctly on XeHP SDV/PVC/DG2 (Matt R)
- Implement Wa_1606376872 for Xe_LP (Gustavo)
- Consider GSI offset when doing MCR lookups on Meteorlake+ (Matt R.)
- Add engine TLB invalidation for Meteorlake (Matt R.)
- Fix GSC Driver-FLR completion on Meteorlake (Alan)
- Fix GSC races on driver load/unload on Meteorlake+ (Daniele)
- Disable MC6 for MTL A step (Badal)
- Consolidate TLB invalidation flow (Tvrtko)
- Improve debug GuC/HuC debug messages (Michal Wa., John)
- Move fd_install after last use of fence (Rob)
- Initialize the obj flags for shmem objects (Aravind)
- Fix missing debug object activation (Nirmoy)
- Probe lmem before the stolen portion (Matt A)
- Improve clean up of GuC busyness stats worker (John)
- Fix missing return code checks in GuC submission init (John)
- Annotate two more workaround/tuning registers as MCR on PVC (Matt R)
- Fix GEN8_MISCCPCTL definition and remove unused INF_UNIT_LEVEL_CLKGATE (Lucas)
- Use sysfs_emit() and sysfs_emit_at() (Nirmoy)
- Make kobj_type structures constant (Thomas W.)
- make kobj attributes const on gt/ (Jani)
- Remove the unused virtualized start hack on buddy allocator (Matt A)
- Remove redundant check for DG1 (Lucas)
- Move DG2 tuning to the right function (Lucas)
- Rename dev_priv to i915 for private data naming consistency in gt/ (Andi)
- Remove unnecessary whitelisting of CS_CTX_TIMESTAMP on Xe_HP platforms (Matt R.)
-
- Escape wildcard in method names in kerneldoc (Bagas)
- Selftest improvements (Chris, Jonathan, Tvrtko, Anshuman, Tejas)
- Fix sparse warnings (Jani)
[airlied: fix unused variable in intel_workarounds]
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZBMSb42yjjzczRhj@jlahtine-mobl.ger.corp.intel.com
As lima_gem_add_deps() performs the same steps as
drm_sched_job_add_syncobj_dependency(), replace the open-coded
implementation in Lima in order to simply use the DRM function.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Qiang Yu <yuq825@gmail.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230224214133.411966-1-mcanal@igalia.com
drm-misc-next for v6.4-rc1:
Cross-subsystem Changes:
- Add drm_bridge.h to drm_bridge maintainers.
Core Changes:
- Assorted fixes to TTM, tests, format-helper, accel.
- Assorted Makefile fixes to drivers and accel.
- Implement fbdev emulation for GEM DMA drivers, and convert a lot of
drivers to use it.
- Use tgid instead of pid for tracking clients.
Driver Changes:
- Assorted fixes in rockchip, vmwgfx, nouveau, cirrus.
- Add imx25 driver.
- Add Elida KD50T048A, Sony TD4353, Novatek NT36523, STARRY 2081101QFH032011-53G panels.
- Add 4K mode support to rockchip.
- Convert cirrus to use regular atomic helpers, and more cirrus
improvements.
- Add damage clipping to cirrus, virtio.
[airlied: add drm_bridge.h include to imx]
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f7b765c7-d49d-edb5-2a6a-4f7a7be16a59@linux.intel.com
Keeping DC states enabled is incompatible with the _noarm()/_arm()
split we use for writing pipe/plane registers. When DC5 and PSR
are enabled, all pipe/plane registers effectively become self-arming
on account of DC5 exit arming the update, and PSR exit latching it.
What probably saves us most of the time is that (with PIPE_MISC[21]=0)
all pipe register writes themselves trigger PSR exit, and then
we don't re-enter PSR until the idle frame count has elapsed.
So it may be that the PSR exit happens already before we've
updated the state too much.
Also the PSR1 panel (at least on this KBL) seems to discard the first
frame we trasmit, presumably still scanning out from its internal
framebuffer at that point. So only the second frame we transmit is
actually visible. But I suppose that could also be panel specific
behaviour. I haven't checked out how other PSR panels behave, nor
did I bother to check what the eDP spec has to say about this.
And since this really is all about DC states, let's switch from
the MODESET domain to the DC_OFF domain. Functionally they are
100% identical. We should probably remove the MODESET domain...
And for good measure let's toss in an assert to the place where
we do the _noarm() register writes to make sure DC states are
in fact off.
v2: Just use intel_display_power_is_enabled() (Imre)
Cc: <stable@vger.kernel.org> #v5.17+
Cc: Manasi Navare <navaremanasi@google.com>
Cc: Drew Davenport <ddavenport@chromium.org>
Cc: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Fixes: d13dde449580 ("drm/i915: Split pipe+output CSC programming to noarm+arm pair")
Fixes: f8a005eb8972 ("drm/i915: Optimize icl+ universal plane programming")
Fixes: 890b6ec4a522 ("drm/i915: Split skl+ plane update into noarm+arm pair")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320183532.17727-1-ville.syrjala@linux.intel.com
Unlike SKL/GLK the ICL CSC unit suffers from a new issue where
CSC_MODE arming is sticky. That is, once armed it remains armed
causing the CSC coeff/offset registers to become effectively
self-arming.
CSC coeff/offset registers writes no longer disarm the CSC,
but fortunately register read still do. So we can use that
to disarm the CSC unit once the registers for the current
frame have been latched. This avoid s the self-arming behaviour
from persisting into the next frame's .color_commit_noarm()
call.
Cc: <stable@vger.kernel.org> #v5.19+
Cc: Manasi Navare <navaremanasi@google.com>
Cc: Drew Davenport <ddavenport@chromium.org>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Fixes: d13dde449580 ("drm/i915: Split pipe+output CSC programming to noarm+arm pair")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320095438.17328-5-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
We're going to need stuff after the color management
register latching has happened. Add a corresponding hook.
Cc: <stable@vger.kernel.org> #v5.19+
Cc: Manasi Navare <navaremanasi@google.com>
Cc: Drew Davenport <ddavenport@chromium.org>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320095438.17328-4-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
SKL/GLK CSC unit suffers from a nasty issue where a CSC
coeff/offset register read or write between DC5 exit and
PSR exit will undo the CSC arming performed by DMC, and
then during PSR exit the hardware will latch zeroes into
the active CSC registers. This causes any plane going
through the CSC to output all black.
We can sidestep the issue by making sure the PSR exit has
already actually happened before we touch the CSC coeff/offset
registers. Easiest way to guarantee that is to just move the
CSC programming back into the .color_commir_arm() as we force
a PSR exit (and crucially wait for it to actually happen)
prior to touching the arming registers.
When PSR (and thus also DC states) are disabled we don't
have anything to worry about, so we can keep using the
more optional _noarm() hook for writing the CSC registers.
Cc: <stable@vger.kernel.org> #v5.19+
Cc: Manasi Navare <navaremanasi@google.com>
Cc: Drew Davenport <ddavenport@chromium.org>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8283
Fixes: d13dde449580 ("drm/i915: Split pipe+output CSC programming to noarm+arm pair")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320095438.17328-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
We're going to want different behavior for skl/glk vs. icl
in .color_commit_noarm(), so split the hook into two. Arguably
we already had slightly different behaviour since
csc_enable/gamma_enable are never set on icl+, so the old
code was perhaps a bit confusing as well.
Cc: <stable@vger.kernel.org> #v5.19+
Cc: Manasi Navare <navaremanasi@google.com>
Cc: Drew Davenport <ddavenport@chromium.org>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320095438.17328-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Enable SDP error detection configuration, this will set CRC16 in
128b/132b link layer.
For Display version 13 a hardware bit31 in register VIDEO_DIP_CTL is
added to enable/disable SDP CRC applicable for DP2.0 only, but the
default value of this bit will enable CRC16 in 128b/132b hence
skipping this write.
Corrective actions on SDP corruption is yet to be defined.
v2: Moved the CRC enable to link training init(Jani N)
v3: Moved crc enable to ddi pre enable <Jani N>
v4: Separate function for SDP CRC16 (Jani N)
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230302081532.765821-3-arun.r.murthy@intel.com
DP2.0 E11 defines a new register to facilitate SDP error detection by a
128B/132B capable DPRX device.
v2: Update the macro name to reflect the DP spec(Harry)
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230302081532.765821-2-arun.r.murthy@intel.com
The pipe may differ from crtc index if pipes are fused off. For testing
purposes, IGT needs to know the pipe.
There's already a I915_GET_PIPE_FROM_CRTC_ID IOCTL for this. However,
the upcoming Xe driver won't have that IOCTL, and going forward, we'll
want a unified interface for testing i915 and Xe, as they share the
display code. Thus add the debugfs for i915 display.
v2: User letters for pipe names (Ville)
Cc: Bhanuprakash Modem <bhanuprakash.modem@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bhanuprakash Modem <bhanuprakash.modem@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320124429.786985-2-jani.nikula@intel.com
Convert the crtc debugfs code to use struct intel_crtc instead of struct
drm_crtc.
v2: Fix build for CONFIG_DRM_I915_DEBUG_VBLANK_EVADE=y (kernel test robot)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320124429.786985-1-jani.nikula@intel.com
clang with W=1 reports
drivers/gpu/drm/gma500/psb_irq.c:35:19: error: unused function
'gma_pipe_event' [-Werror,-Wunused-function]
static inline u32 gma_pipe_event(int pipe)
^
This function is not used, so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230319142320.1704336-1-trix@redhat.com
BSPEC has updated the cdclk audio keepalives AUD_TS_CDCLK_M value to 60
for all supported platforms and refclks.
BSPEC: 54034
BSPEC: 55409
BSPEC: 65243
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316234654.3797572-1-clinton.a.taylor@intel.com
As mmu refactor and nic resume are not relevant anymore, remove
their TODO comments.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
FW had one data route for tpc0 and tpc1 when running in secured mode
and a different one when running without secured mode. After fw fixed
this issue, both mode have the same data path.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order for the user to be aware of unexpected events in Gaudi2 that
aren't assigned to a specific engine, we are adding the handling of
this dedicated interrupt.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Replace initialization of "struct cpucp_packet" from "{0} to "{}" to
avoid a "missing braces around initializer" compilation warning.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
After getting page fault in gaudi2, we need to clear the valid bit
instead of the address.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
All engine masks are exposed to user, make sure user gets the
correct rotator enabled mask in gaudi2.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Some names of events has been modified/added.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Commit 2c204f3d53218d ("accel: add dedicated minor for accelerator
devices") adds link to accelerator nodes section of DRM internals doc
(Documentation/gpu/drm-internals.rst), but the target doesn't exist.
Instead, there is only an introduction doc for computer accelerator
subsytem.
Link to that doc until there is documentation of accelerator internals.
Fixes: 2c204f3d53218d ("accel: add dedicated minor for accelerator devices")
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We expose this in order for user applications to know how much dram
is reserved for internal use.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Remove all '\n' from strings which are passed as arguments to
gaudi2_print_event(), because the newline character is added internally
in this function.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
