IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Removes some functions that are not used anywhere:
dbgi_rd_rsp3() dbgi_wr_addr3()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a set of three fixes: one to correct an abort path thinko causing
failures (and a panic) in USB on device misbehaviour, One to fix an out of
order issue in the fnic driver and one to match discard expectations to qemu
which otherwise cause Linux to behave badly as a guest.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJUpsmHAAoJEDeqqVYsXL0MdToH/1UsmOdtxNh6AfBDWWYi45o8
kBno1gTnRrDgIlOiRu+BtmL25A1rNcCdCQKjG6JBEBruqUVAwZztktGjfuSvso6s
EYbrnE+5DmDs6cW8pp6GK3QGV+R+AmbT8oBbe/Kpg5LdTsdnQOozSycUp7X3XgTi
pLOm6rW/AgEV1QFcQz1bjI6cnbcOZMcGZnC5qwphiKgBnVYd+PZY24RSHDKCu/va
z2lsa5yqXFHKZZZRhYG343YqCTf3Dkph78124JoNvVm3EjO+GQAAiojiUa7l59UF
RqNRqeMxfz2cPmBnJxbNmWiP1YQGBgOaNDRgc7D7SPxaMwUe9444Gm4MkoZWzmQ=
=706l
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of three fixes: one to correct an abort path thinko
causing failures (and a panic) in USB on device misbehaviour, One to
fix an out of order issue in the fnic driver and one to match discard
expectations to qemu which otherwise cause Linux to behave badly as a
guest"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
SCSI: fix regression in scsi_send_eh_cmnd()
fnic: IOMMU Fault occurs when IO and abort IO is out of order
sd: tweak discard heuristics to work around QEMU SCSI issue
Until now, when VLAN acceleration was in use, the bytes of the VLAN header
were not included in port or flow byte counters. They were however
included when VLAN acceleration was not used. This commit corrects the
inconsistency, by always including the VLAN header in byte counters.
Previous discussion at
http://openvswitch.org/pipermail/dev/2014-December/049521.html
Reported-by: Motonori Shindo <mshindo@vmware.com>
Signed-off-by: Ben Pfaff <blp@nicira.com>
Reviewed-by: Flavio Leitner <fbl@sysclose.org>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Jarosch reported IPsec TCP stalls when a PMTU event occurs.
In fact the problem was completely unrelated to IPsec. The bug is
also reproducible if you just disable TSO/GSO.
The problem is that when the MSS goes down, existing queued packet
on the TX queue that have not been transmitted yet all look like
TSO packets and get treated as such.
This then triggers a bug where tcp_mss_split_point tells us to
generate a zero-sized packet on the TX queue. Once that happens
we're screwed because the zero-sized packet can never be removed
by ACKs.
Fixes: 1485348d242 ("tcp: Apply device TSO segment limit earlier")
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Signed-off-by: David S. Miller <davem@davemloft.net>
Not needed, only four cases:
- kfree_skb (or one of its aliases).
Don't need to zero, memory will be freed.
- kfree_skb_partial and head was stolen: memory will be freed.
- skb_morph: The skb header fields (including tc ones) will be
copied over from the 'to-be-morphed' skb right after
skb_release_head_state returns.
- skb_segment: Same as before, all the skb header
fields are copied over from the original skb right away.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg say:
====================
pull request: bluetooth-next 2014-12-31
Here's the first batch of bluetooth patches for 3.20.
- Cleanups & fixes to ieee802154 drivers
- Fix synchronization of mgmt commands with respective HCI commands
- Add self-tests for LE pairing crypto functionality
- Remove 'BlueFritz!' specific handling from core using a new quirk flag
- Public address configuration support for ath3012
- Refactor debugfs support into a dedicated file
- Initial support for LE Data Length Extension feature from Bluetooth 4.2
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing too exciting as a new year's start here: most of fixes are for
ASoC, a boot crash fix on OMAP for deferred probe, a few driver
specific fixes (Intel, dwc, rockchip, rt5677), in addition to typo
fixes in kerneldoc comments for PCM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ARQX
-----END PGP SIGNATURE-----
Merge tag 'sound-3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Nothing too exciting as a new year's start here: most of fixes are for
ASoC, a boot crash fix on OMAP for deferred probe, a few driver
specific fixes (Intel, dwc, rockchip, rt5677), in addition to typo
fixes in kerneldoc comments for PCM"
* tag 'sound-3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Fix kerneldoc for params_*() functions
ASoC: rockchip: i2s: fix maxburst of dma data to 4
ASoC: rockchip: i2s: fix error defination of transmit data level
ASoC: Intel: correct the fixed free block allocation
ASoC: rt5677: fixed rt5677_dsp_vad_put rt5677_dsp_vad_get panic
ASoC: Intel: Fix BYTCR machine driver MODULE_ALIAS
ASoC: Intel: Fix BYTCR firmware name
ASoC: dwc: Iterate over all channels
ASoC: dwc: Ensure FIFOs are flushed to prevent channel swap
ASoC: Intel: Add I2C dependency to two new machines
ASoC: dapm: Remove snd_soc_of_parse_audio_routing() due to deferred probe
This results in an approximately 30% increase in throughput
when handling encapsulated bulk traffic.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the only tunnel protocol that supports GRO with encapsulated
Ethernet is VXLAN. This pulls out the Ethernet code into a proper layer
so that it can be used by other tunnel protocols such as GRE and Geneve.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Altera network device doesn't come up after
ifconfig eth0 down
ifconfig eth0 up
The reason behind is clearing priv->phydev during tse_shutdown().
The phydev is not restored back at tse_open().
Resubmiting as to follow Tobias Klauser suggestion.
phy_start/phy_stop are called on each ifup/ifdown and
phy_disconnect is called once during the module removal.
Signed-off-by: Kostya Belezko <bkostya@hotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
mlx4 driver fixes for 3.19-rc2
Please push Maor's patch to -stable >= 3.17
Jack's fixes error-flow issues introduced in 3.19-rc1, no need for -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't call UNMAP_FA here, this is done in mlx4_load_one.
If mlx4_query_func fails, we need to invoke CLOSE_HCA for both
native and master.
Fixes: a0eacca948d2 ('net/mlx4_core: Refactor mlx4_load_one')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, mlx4_mt_rereg_write filled the MPT's entity_size with the
old MTT's page shift, which could result in using an incorrect offset.
Fix the initialization to be after we calculate the new MTT offset.
In addition, assign mtt order to -1 after calling mlx4_mtt_cleanup. This
is necessary in order to mark the MTT as invalid and avoid freeing it later.
Fixes: e630664 ('mlx4_core: Add helper functions to support MR re-registration')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set the clock speed in read/write which will be performed
unnecessarily for each mdio access. Init it during probe is enough.
Also, the hardcoded clock value is not a proper way for all SoCs.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Which is wrong and not used, so no extra space needed by
mdiobus_alloc_size(), use mdiobus_alloc() instead.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the reset is just clock setting, individual mdio reset is
not available.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 14516bb7bb6ffbd49f35389f9ece3b2045ba5815.
This was causing regression test failures with generic/285 with an ext3
filesystem using CONFIG_EXT4_USE_FOR_EXT23.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
There's a single change here, fixing a vhost bug where vhost initialization
fails due to used ring alignment check being too strict.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUoRcnAAoJECgfDbjSjVRpb7IIAIGoNJkB56Q3WWX0rP5i1Lqi
Uxt8lrvySotzoWMVZlm2pGRiwJv2T1dQXKWetvZDn0GuwCBi2/vm2l4eOhu1K+VV
jOtKk8n8kDJVgMOGaJUwqt8lhDbqGwHHDUCKDk78/pV5Q959bAVo143vWOh2DixQ
m3YmvmLwyhF6CYNwOD0HqllaojDPBAP3k22GdmJNy/H7CpcOSYK7BRoiQHX7FsbR
I3Kj/7gf5OlZFzLTLxNx/O01p1BkX6EusADfl3+tl6nggc6vqW9fHNz/TZLGh9I/
ap0Ng3pm8q/t6S6wsPj8wzTHNesK4gVWvecRN8kZV8UQY2rwd/y7R/k+VpJDseg=
=+Pmi
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull vhost cleanup and virtio bugfix
"There's a single change here, fixing a vhost bug where vhost
initialization fails due to used ring alignment check being too
strict"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: relax used address alignment
virtio_ring: document alignment requirements
If the check of adapter fails and goes into the 'else' branch, the
return value 'err' should not still be zero.
Signed-off-by: Yongjian Xu <xuyongjiande@gmail.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
The patch also modifies the test of mgp->cmd to satisfy checkpatch.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-12-31
This series contains updates to fixes for e100, igb and i40e.
John Linville fixes a typo in e100 that has been around for some time,
where an attempted revert actually inverted the test for eeprom_mdix_enabled.
Todd fixes up a code comment that should have been removed back in 2007.
Joe Perches fixes a possible memory leak in i40e which was reported by
Dan Carpenter using smatch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Roger Chen says:
====================
support GMAC driver for RK3288
Roger Chen (6):
patch1: add driver for Rockchip RK3288 SoCs integrated GMAC
patch2: define clock ID used for GMAC
patch3: modify CRU config for Rockchip RK3288 SoCs integrated GMAC
patch4: dts: rockchip: add gmac info for rk3288
patch5: dts: rockchip: enable gmac on RK3288 evb board
patch6: add document for Rockchip RK3288 GMAC
Tested on rk3288 evb board:
Execute the following command to enable ethernet,
set local IP and ping a remote host.
busybox ifconfig eth0 up
busybox ifconfig eth0 192.168.1.111
ping 192.168.1.1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The document descripts how to add properties for GMAC in device tree.
change since v2:
1. remove power-gpio, reset-gpio, phyirq-gpio, pmu_regulator setting
2. add "snps,reset-gpio", "snps,reset-active-low;" "snps,reset-delays-us"
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enable gmac in rk3288-evb-rk808.dts
changes since v2:
1. add fixed regulator for PHY
2. remove power-gpio, reset-gpio, phyirq-gpio, pmu_regulator setting
3. add "snps,reset-gpio", "snps,reset-active-low;" "snps,reset-delays-us"
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add gmac info in rk3288.dtsi for GMAC driver
changes since v2:
1. add drive-strength in the pinctrl settings
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
modify CRU config for GMAC driver
changes since v2:
1. remove SCLK_MAC_PLL
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is based on stmmac driver.
changes since v2:
- use tab instead of space for macros
- use HIWORD_UPDATE macro for GMAC_CLK_RX_DL_CFG and GMAC_CLK_TX_DL_CFG
- remove drive-strength setting in the driver and set it in the pinctrl settings
- use dev_err instead of pr_err
- remove clock names's macros, just use the real name of the clock
- use devm_clk_get() instead of clk_get()
- remove clk_set_parent(bsp_priv->clk_mac, bsp_priv->clk_mac_pll)
- remove gpio setting for LDO, just use regulator API
- remove phy reset using gpio in the glue layer, it has been handled in the stmmac driver
- remove handling phy interrupt (mii interrupt)
changes since v1:
- use BIT() to set register
- combine two remap_write() operations into one for the same register
- use macros for register value setting
- remove grf fail check in rk_gmac_setup() and save all the check in set_rgmii_speed()
- remove .tx_coe=1 in rk_gmac_data
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I didn't notice that return in the code, fix it by
adding a goto out instead to free the memory.
Fixes:
> New smatch warnings:
> drivers/net/ethernet/intel/i40e/i40e_debugfs.c:832 i40e_dbg_dump_desc() warn: possible memory leak of 'ring'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck says:
====================
fib_trie: Reduce time spent in fib_table_lookup by 35 to 75%
These patches are meant to address several performance issues I have seen
in the fib_trie implementation, and fib_table_lookup specifically. With
these changes in place I have seen a reduction of up to 35 to 75% for the
total time spent in fib_table_lookup depending on the type of search being
performed.
On a VM running in my Corei7-4930K system with a trie of maximum depth of 7
this resulted in a reduction of over 370ns per packet in the total time to
process packets received from an ixgbe interface and route them to a dummy
interface. This represents a failed lookup in the local trie followed by
a successful search in the main trie.
Baseline Refactor
ixgbe->dummy routing 1.20Mpps 2.21Mpps
------------------------------------------------------------
processing time per packet 835ns 453ns
fib_table_lookup 50.1% 418ns 25.0% 113ns
check_leaf.isra.9 7.9% 66ns -- --
ixgbe_clean_rx_irq 5.3% 44ns 9.8% 44ns
ip_route_input_noref 2.9% 25ns 4.6% 21ns
pvclock_clocksource_read 2.6% 21ns 4.6% 21ns
ip_rcv 2.6% 22ns 4.0% 18ns
In the simple case of receiving a frame and dropping it before it can reach
the socket layer I saw a reduction of 40ns per packet. This represents a
trip through the local trie with the correct leaf found with no need for
any backtracing.
Baseline Refactor
ixgbe->local receive 2.65Mpps 2.96Mpps
------------------------------------------------------------
processing time per packet 377ns 337ns
fib_table_lookup 25.1% 95ns 25.8% 87ns
ixgbe_clean_rx_irq 8.7% 33ns 9.0% 30ns
check_leaf.isra.9 7.2% 27ns -- --
ip_rcv 5.7% 21ns 6.5% 22ns
These changes have resulted in several functions being inlined such as
check_leaf and fib_find_node, but due to the code simplification the
overall size of the code has been reduced.
text data bss dec hex filename
16932 376 16 17324 43ac net/ipv4/fib_trie.o - before
15259 376 8 15643 3d1b net/ipv4/fib_trie.o - after
Changes since RFC:
Replaced this_cpu_ptr with correct call to this_cpu_inc in patch 1
Changed test for leaf_info mismatch to (key ^ n->key) & li->mask_plen in patch 10
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds a tracking value for the maximum suffix length of all
prefixes stored in any given tnode. With this value we can determine if we
need to backtrace or not based on if the suffix is greater than the pos
value.
By doing this we can reduce the CPU overhead for lookups in the local table
as many of the prefixes there are 32b long and have a suffix length of 0
meaning we can immediately backtrace to the root node without needing to
test any of the nodes between it and where we ended up.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason the compiler doesn't seem to understand that when we are in
a loop that runs from tnode_child_length - 1 to 0 we don't expect the value
of tn->bits to change. As such every call to tnode_get_child was rerunning
tnode_chile_length which ended up consuming quite a bit of space in the
resultant assembly code.
I have gone though and verified that in all cases where tnode_get_child
is used we are either winding though a fixed loop from tnode_child_length -
1 to 0, or are in a fastpath case where we are verifying the value by
either checking for any remaining bits after shifting index by bits and
testing for leaf, or by using tnode_child_length.
size net/ipv4/fib_trie.o
Before:
text data bss dec hex filename
15506 376 8 15890 3e12 net/ipv4/fib_trie.o
After:
text data bss dec hex filename
14827 376 8 15211 3b6b net/ipv4/fib_trie.o
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change pulls the node_set_parent functionality out of put_child_reorg
and instead leaves that to the function to take care of as well. By doing
this we can fully construct the new cluster of tnodes and all of the
pointers out of it before we start routing pointers into it.
I am suspecting this will likely fix some concurency issues though I don't
have a good test to show as such.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change pushes the tnode freeing down into the inflate and halve
functions. It makes more sense here as we have a better grasp of what is
going on and when a given cluster of nodes is ready to be freed.
I believe this may address a bug in the freeing logic as well. For some
reason if the freelist got to a certain size we would call
synchronize_rcu(). I'm assuming that what they meant to do is call
synchronize_rcu() after they had handed off that much memory via
call_rcu(). As such that is what I have updated the behavior to be.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the assignment of the tnode to the parent is
handled directly within whatever function is currently handling the node be
it inflate, halve, or resize. By doing this we can avoid some of the need
to set NULL pointers in the tree while we are resizing the subnodes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change pulls the logic for if we should inflate/halve the nodes out
into separate functions. It also addresses what I believe is a bug where 1
full node is all that is needed to keep a node from ever being halved.
Simple script to reproduce the issue:
modprobe dummy; ifconfig dummy0 up
for i in `seq 0 255`; do ifconfig dummy0:$i 10.0.${i}.1/24 up; done
ifconfig dummy0:256 10.0.255.33/16 up
for i in `seq 0 254`; do ifconfig dummy0:$i down; done
Results from /proc/net/fib_triestat
Before:
Local:
Aver depth: 3.00
Max depth: 4
Leaves: 17
Prefixes: 18
Internal nodes: 11
1: 8 2: 2 10: 1
Pointers: 1048
Null ptrs: 1021
Total size: 11 kB
After:
Local:
Aver depth: 3.41
Max depth: 5
Leaves: 17
Prefixes: 18
Internal nodes: 12
1: 8 2: 3 3: 1
Pointers: 36
Null ptrs: 8
Total size: 3 kB
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change consists of a cut/paste of resize to behind inflate and halve
so that I could remove the two function prototypes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is to start cleaning up some of the rcu_read_lock/unlock
handling. I realized while reviewing the code there are several spots that
I don't believe are being handled correctly or are masking warnings by
locally calling rcu_read_lock/unlock instead of calling them at the correct
level.
A common example is a call to fib_get_table followed by fib_table_lookup.
The rcu_read_lock/unlock ought to wrap both but there are several spots where
they were not wrapped.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that anything that can be shifted by, or compared
to a value shifted by bits is updated to be an unsigned long. This is
mostly a precaution against an insanely huge address space that somehow
starts coming close to the 2^32 root node size which would require
something like 1.5 billion addresses.
I chose unsigned long instead of unsigned long long since I do not believe
it is possible to allocate a 32 bit tnode on a 32 bit system as the memory
consumed would be 16GB + 28B which exceeds the addressible space for any
one process.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change moves the pos value to the other side of the "bits" field. By
doing this it actually simplifies a significant amount of code in the trie.
For example when halving a tree we know that the bit lost exists at
oldnode->pos, and if we inflate the tree the new bit being add is at
tn->pos. Previously to find those bits you would have to subtract pos and
bits from the keylength or start with a value of (1 << 31) and then shift
that.
There are a number of spots throughout the code that benefit from this. In
the case of the hot-path searches the main advantage is that we can drop 2
or more operations from the search path as we no longer need to compute the
value for the index to be shifted by and can instead just use the raw pos
value.
In addition the tkey_extract_bits is now defunct and can be replaced by
get_index since the two operations were doing the same thing, but now
get_index does it much more quickly as it is only an xor and shift versus a
pair of shifts and a subtraction.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the fib_table_insert function to take advantage of the
changes made to improve the performance of fib_table_lookup. As a result
the code should be smaller and run faster then the original.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of the same features I made use of for
fib_table_lookup to streamline fib_find_node. The resultant code should be
smaller and run faster than the original.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is meant to reduce the complexity of fib_table_lookup by reducing
the number of variables to the bare minimum while still keeping the same if
not improved functionality versus the original.
Most of this change was started off by the desire to rid the function of
chopped_off and current_prefix_length as they actually added very little to
the function since they only applied when computing the cindex. I was able
to replace them mostly with just a check for the prefix match. As long as
the prefix between the key and the node being tested was the same we know
we can search the tnode fully versus just testing cindex 0.
The second portion of the change ended up being a massive reordering.
Originally the calls to check_leaf were up near the start of the loop, and
the backtracing and descending into lower levels of tnodes was later. This
didn't make much sense as the structure of the tree means the leaves are
always the last thing to be tested. As such I reordered things so that we
instead have a loop that will delve into the tree and only exit when we
have either found a leaf or we have exhausted the tree. The advantage of
rearranging things like this is that we can fully inline check_leaf since
there is now only one reference to it in the function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that leaf and tnode are the same struct. As a
result there is no need for rt_trie_node anymore since everyting can be
merged into tnode.
On 32b systems this results in the leaf being 4 bytes larger, however I
don't know if that is really an issue as this and an eariler patch that
added bits & pos have increased the size from 20 to 28. If I am not
mistaken slub/slab allocate on power of 2 sizes so 20 was likely being
rounded up to 32 anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
