IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The Tegra FUSE belongs to the core power domain and we're going to enable
GENPD support for the core domain. Now FUSE device must be resumed using
runtime PM API in order to initialize the FUSE power state. Add runtime PM
support to the FUSE driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The fuse->clk must be cleared if FUSE driver fails to probe, otherwise
tegra_fuse_readl() will crash. It's unlikely to happen in practice,
nevertheless let's correct it for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both PMC and cpuidle drivers are probed at the same init level and
cpuidle depends on the PMC suspend mode. Add new default suspend mode
that indicates whether PMC driver has been probed and reset the mode in
a case of deferred probe of the PMC driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove including <linux/version.h> that don't need it.
V1->V2: Split the patch in two
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The regulator coupler drivers now use regulator-driver API function that
isn't available during compile-testing. Make regulator coupler drivers
dependent on CONFIG_REGULATOR in Kconfig.
Fixes: 03978d42ed ("soc/tegra: regulators: Bump voltages on system reboot")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the end
of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing legacy
mach/* include dependencies and moving platform detection/config to
drivers/soc. Also some updates/cleanup of platform data.
- Core power domain support for Tegra platforms, and some improvements
in build test coverage by adding stubs for compile test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI) SMP
support on i.MX7D, SoC ID setup for i.MX50, removal of platform data
and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip.
-----BEGIN PGP SIGNATURE-----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=b6Jo
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Olof Johansson:
"A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the
end of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing
legacy mach/* include dependencies and moving platform
detection/config to drivers/soc. Also some updates/cleanup of
platform data.
- Core power domain support for Tegra platforms, and some
improvements in build test coverage by adding stubs for compile
test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI)
SMP support on i.MX7D, SoC ID setup for i.MX50, removal of platform
data and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip"
* tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (53 commits)
MAINTAINERS: Add myself as TEE subsystem reviewer
ixp4xx: fix spelling mistake in Kconfig "Devce" -> "Device"
hw_random: ixp4xx: Add OF support
hw_random: ixp4xx: Add DT bindings
hw_random: ixp4xx: Turn into a module
hw_random: ixp4xx: Use SPDX license tag
hw_random: ixp4xx: enable compile-testing
pata: ixp4xx: split platform data to its own header
soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h
PCI: ixp4xx: Add a new driver for IXP4xx
PCI: ixp4xx: Add device tree bindings for IXP4xx
ARM/ixp4xx: Make NEED_MACH_IO_H optional
ARM/ixp4xx: Move the virtual IObases
MAINTAINERS: ARM/MStar/Sigmastar SoCs: Add a link to the MStar tree
ARM: debug: add UART early console support for MSTAR SoCs
ARM: dts: ux500: Fix LED probing
ARM: imx: add smp support for imx7d
ARM: imx6q: drop of_platform_default_populate() from init_machine
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
soc/tegra: fuse: Fix Tegra234-only builds
...
fuse->base can not be unmapped if allocate lookups failed in
tegra_init_fuse(), because it is an early_initcall, the driver
will be loaded anyway and fuse->base will be accessed by other
functions later, so remove the return -ENOMEM after allocating
lookups failed to make less confusing.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
[treding@nvidia.com: drop error message, out-of-memory is noisy anyway]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The core voltage shall not drop until state of core domain is synced,
i.e. all device drivers that use core domain are loaded and ready.
Support core domain state syncing. The core domain driver invokes the
core-regulator voltage syncing once the state of domain is synced, at
this point the core voltage is allowed to go lower than the level left
after bootloader.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add driver state syncing that is invoked once all PMC consumers are
attached and ready. The consumers are the power domain clients.
The synchronization callback is invoked once all client drivers are
probed, the driver core handles this for us. This callback informs
PMC driver that all voltage votes are initialized by each PD client
and it's safe to begin voltage scaling of the core power domain.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[treding@nvidia.com: squash DT backwards-compatibility patch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
NVIDIA Tegra SoCs have multiple power domains, each domain corresponds
to an external SoC power rail. Core power domain covers vast majority of
hardware blocks within a Tegra SoC. The voltage of a power domain should
be set to a level which satisfies all devices within the power domain.
Add support for the core power domain which controls voltage state of the
domain. This allows us to support system-wide DVFS on Tegra20-210 SoCs.
The PMC powergate domains now are sub-domains of the core domain, this
requires device-tree updating, older DTBs are unaffected and will continue
to work as before.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[treding@nvidia.com: squash lockdep class removal patch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Ensure that SoC voltages are at a level suitable for a system reboot.
This is important for some devices that use CPU reset method for the
rebooting. SoC CPU and core voltages now are be restored to a level
that is suitable for rebooting. This patch fixes hang on reboot on
Asus Transformer TF101, it was also reported as fixing some of reboot
issues on Toshiba AC100.
Reported-by: Nikola Milosavljević <mnidza@outlook.com>
Tested-by: Nikola Milosavljević <mnidza@outlook.com> # TF101
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Core changes:
- A semantic change to handle pinmux and pinconf in explicit order
while up until now we depended on the semantic order in the
device tree. The device tree is a functional programming
language and does not imply any order, so the right thing is
for the pin control core to provide these semantics.
- Add a new pinmux-select debugfs file which makes it possible to
go in and select functions for a pin manually (iteratively, at
the prompt) for debugging purposes.
- Fixes to gpio regmap handling for a new pin control driver
making use of regmap-gpio.
- Use octal permissions on debugfs files.
New drivers:
- A massive rewrite of the former custom pin control driver for
MIPS Broadcom devices to instead use the pin control subsystem.
New pin control drivers for BCM6345, BCM6328, BCM6358, BCM6362,
BCM6368, BCM63268 and BCM6318 SoC variants are implemented.
- Support for PM8350, PM8350B, PM8350C, PMK8350, PMR735A and
PMR735B in the Qualcomm PMIC GPIO driver. Also the two GPIOs
on PM8008 are supported.
- Support for the Rockchip RK3568/RK3566 pin controller.
- Support for Ingenic JZ4730, JZ4750, JZ4755, JZ4775 and
X2000.
- Support for Mediatek MTK8195.
- Add a new Xilinx ZynqMP pin control driver.
Driver improvements and non-urgent fixes:
- Modularization and improvements of the Rockchip drivers.
- Some new pins added to the description of new Renesas SoCs.
- Clarifications of the GPIO base calculation in the Intel driver.
- Fix the function names for the MPP54 and MPP55 pins in the Armada
CP110 pin controller.
- GPIO wakeup interrupt map for Qualcomm SC7280 and SM8350.
- Support for ACPI probing of the Qualcomm SC8180x.
- Fix interrupt clear status on rockchip
- Fix some missing pins on the Ingenic JZ4770, some semantic
fixes for the behaviour of the Ingenic pin controller.
Add DMIC pins for JZ4780, X1000, X1500 and X1830.
- A slew of janitorial like of_node_put() calls.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAmCL5sAACgkQQRCzN7AZ
XXNX5RAAtdPvDrPzzWdeqNLyodnJu/SyeA2xbmsvywrSvgpSx3FojFW9AXY/sr7w
RuhGGA5KhnrovwiabRKoZ0d0lC/JtKdx5g2o9ePFHDy+7BzFnVacBjL38UftSKy0
4QpDNJ3zock/XTUgJdaJEsbHhP/N4fOF/SbLpguYzGz7JpybNrZ+2M73yeQSL6uE
yuhn/AgFMLgWS47nSAH91Yt387+XCEfB75nftXyFSN9GpQ9i3VixWsG3Um/Stoma
aR7IIknvHdpCrOHH1IKohYcdlOkE7Wh2wHXSJVv26M49Ri5KSXu17lsUknebQ/oq
UeDYdd/2q/wFjxdEbG2tqinEYHs3e1RPmatVesgyibtYHGwjnSFo/G6UtG4948ii
1exwBi+0fw58YWLu/z4bhnNtZx6VsOev6mJ5GF7pyYzGIJy3r5J/9KCDzOJEoLom
YTVmgZRjzJuH/i0rPgyg3lSxlP/pdvdk1YUMlIYN1zWdPnRqj7/q+qaxPOkltqD+
20NFkvhQuuq+dLn4jtNK9xr2+vIKxIRPClT3D/lAihEPC5MUaFw/+y/V7c1hEJfS
d1dh5DwgHK7i55/lqLFaXeNNYsmY/SiFecoB8xyFnOJFsHlSHe/6NfjmRhOMUn6V
IX2GG4CBAzaheIWtN/ub/DcQ1vwA2n9hO5WX+Y3CXkIxXUFPmJY=
=QrEn
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"There is a lot going on!
Core changes:
- A semantic change to handle pinmux and pinconf in explicit order
while up until now we depended on the semantic order in the device
tree. The device tree is a functional programming language and does
not imply any order, so the right thing is for the pin control core
to provide these semantics.
- Add a new pinmux-select debugfs file which makes it possible to go
in and select functions for a pin manually (iteratively, at the
prompt) for debugging purposes.
- Fixes to gpio regmap handling for a new pin control driver making
use of regmap-gpio.
- Use octal permissions on debugfs files.
New drivers:
- A massive rewrite of the former custom pin control driver for MIPS
Broadcom devices to instead use the pin control subsystem. New pin
control drivers for BCM6345, BCM6328, BCM6358, BCM6362, BCM6368,
BCM63268 and BCM6318 SoC variants are implemented.
- Support for PM8350, PM8350B, PM8350C, PMK8350, PMR735A and PMR735B
in the Qualcomm PMIC GPIO driver. Also the two GPIOs on PM8008 are
supported.
- Support for the Rockchip RK3568/RK3566 pin controller.
- Support for Ingenic JZ4730, JZ4750, JZ4755, JZ4775 and X2000.
- Support for Mediatek MTK8195.
- Add a new Xilinx ZynqMP pin control driver.
Driver improvements and non-urgent fixes:
- Modularization and improvements of the Rockchip drivers.
- Some new pins added to the description of new Renesas SoCs.
- Clarifications of the GPIO base calculation in the Intel driver.
- Fix the function names for the MPP54 and MPP55 pins in the Armada
CP110 pin controller.
- GPIO wakeup interrupt map for Qualcomm SC7280 and SM8350.
- Support for ACPI probing of the Qualcomm SC8180x.
- Fix interrupt clear status on rockchip
- Fix some missing pins on the Ingenic JZ4770, some semantic fixes
for the behaviour of the Ingenic pin controller. Add DMIC pins for
JZ4780, X1000, X1500 and X1830.
- A slew of janitorial like of_node_put() calls"
* tag 'pinctrl-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: Add Xilinx ZynqMP pinctrl driver support
firmware: xilinx: Add pinctrl support
pinctrl: rockchip: do coding style for mux route struct
pinctrl: Add PIN_CONFIG_MODE_PWM to enum pin_config_param
pinctrl: Introduce MODE group in enum pin_config_param
pinctrl: Keep enum pin_config_param ordered by name
dt-bindings: pinctrl: Add binding for ZynqMP pinctrl driver
pinctrl: core: Fix kernel doc string for pin_get_name()
pinctrl: mediatek: use spin lock in mtk_rmw
pinctrl: add drive for I2C related pins on MT8195
pinctrl: add pinctrl driver on mt8195
dt-bindings: pinctrl: mt8195: add pinctrl file and binding document
pinctrl: Ingenic: Add pinctrl driver for X2000.
pinctrl: Ingenic: Add pinctrl driver for JZ4775.
pinctrl: Ingenic: Add pinctrl driver for JZ4755.
pinctrl: Ingenic: Add pinctrl driver for JZ4750.
pinctrl: Ingenic: Add pinctrl driver for JZ4730.
dt-bindings: pinctrl: Add bindings for new Ingenic SoCs.
pinctrl: Ingenic: Reformat the code.
pinctrl: Ingenic: Add DMIC pins support for Ingenic SoCs.
...
Better to have a MODE group of settings to keep them together
when ordered alphabetically. Hence, rename PIN_CONFIG_LOW_POWER_MODE
to PIN_CONFIG_MODE_LOW_POWER.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210412140741.39946-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Print out domain name when reset fails to acquire for debugging purposes
and to make formatting of GENPD errors consistent in the driver.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Switch all clocks of a power domain to a safe rate which is suitable
for all possible voltages in order to ensure that hardware constraints
aren't violated when power domain state toggles.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SW-initiated power gate toggling is dropped by PMC if there is
contention with a HW-initiated toggling, i.e. when one of CPU cores is
gated by cpuidle driver. Software should retry the toggling after 10
microseconds on Tegra20/30 SoCs, hence add the retrying. On Tegra114+ the
toggling method was changed in hardware, the TOGGLE_START bit indicates
whether PMC is busy or could accept the command to toggle, hence handle
that bit properly.
The problem pops up after enabling dynamic power gating of 3D hardware,
where 3D power domain fails to turn on/off "randomly".
The programming sequence and quirks are documented in TRMs, but PMC
driver obliviously re-used the Tegra20 logic for Tegra30+, which strikes
back now. The 10 microseconds and other timeouts aren't documented in TRM,
they are taken from downstream kernel.
Link: https://nv-tegra.nvidia.com/gitweb/?p=linux-2.6.git;a=commit;h=311dd1c318b70e93bcefec15456a10ff2b9eb0ff
Link: https://nv-tegra.nvidia.com/gitweb/?p=linux-3.10.git;a=commit;h=7f36693c47cb23730a6b2822e0975be65fb0c51d
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The tegra_powergate_power_up() has a typo in the error code path where it
will try to disable clocks twice, fix it. In practice that error never
happens, so this is a minor correction.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix voltage coupler lockup which happens when voltage-spread is out
of range due to a bug in the code. The max-spread requirement shall be
accounted when CPU regulator doesn't have consumers. This problem is
observed on Tegra30 Ouya game console once system-wide DVFS is enabled
in a device-tree.
Fixes: 783807436f ("soc/tegra: regulators: Add regulators coupler for Tegra30")
Cc: stable@vger.kernel.org
Reported-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit implements a register map which grants USB (UTMI and HSIC)
sleepwalk registers access to USB PHY drivers. The USB sleepwalk logic
is in PMC hardware block but USB PHY drivers have the best knowledge
of proper programming sequence.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This contains a couple of warning fixes and a fix for a mostly harmless
bug in the process ID retrieval code.
-----BEGIN PGP SIGNATURE-----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=mYgF
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc/tegra: Changes for v5.11-rc1
This contains a couple of warning fixes and a fix for a mostly harmless
bug in the process ID retrieval code.
* tag 'tegra-for-5.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Fix index bug in get_process_id
soc: tegra: fuse: speedo-tegra210: Remove a group of set but unused variables
soc: tegra: fuse: speedo-tegra124: Remove some set but unused variables
Link: https://lore.kernel.org/r/20201127144329.124891-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes the following W=1 kernel build warning(s):
drivers/soc/tegra/fuse/speedo-tegra210.c: In function ‘tegra210_init_speedo_data’:
drivers/soc/tegra/fuse/speedo-tegra210.c:105:56: warning: variable ‘soc_iddq’ set but not used [-Wunused-but-set-variable]
drivers/soc/tegra/fuse/speedo-tegra210.c:105:46: warning: variable ‘gpu_iddq’ set but not used [-Wunused-but-set-variable]
drivers/soc/tegra/fuse/speedo-tegra210.c:105:36: warning: variable ‘cpu_iddq’ set but not used [-Wunused-but-set-variable]
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[treding@nvidia.com: remove unnecessary reads altogether]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fixes the following W=1 kernel build warning(s):
drivers/soc/tegra/fuse/speedo-tegra124.c: In function ‘tegra124_init_speedo_data’:
drivers/soc/tegra/fuse/speedo-tegra124.c:105:38: warning: variable ‘soc_iddq_value’ set but not used [-Wunused-but-set-variable]
drivers/soc/tegra/fuse/speedo-tegra124.c:105:22: warning: variable ‘gpu_iddq_value’ set but not used [-Wunused-but-set-variable]
drivers/soc/tegra/fuse/speedo-tegra124.c:105:6: warning: variable ‘cpu_iddq_value’ set but not used [-Wunused-but-set-variable]
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[treding@nvidia.com: remove unnecessary reads altogether]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The tegra_read_ram_code() is used by EMC drivers and we're going to make
these driver modular, hence this function needs to be exported.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201104164923.21238-3-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Various driver updates for platforms. A bulk of this is smaller fixes or
cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs
and platforms.
-----BEGIN PGP SIGNATURE-----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=tfPb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
The Tegra PMC driver does ungodly things with the interrupt hierarchy,
repeatedly corrupting it by pulling hwirq numbers out of thin air,
overriding existing IRQ mappings and changing the handling flow
of unsuspecting users.
All of this is done in the name of preserving the interrupt hierarchy
even when these levels do not exist in the HW. Together with the use
of proper IRQs for IPIs, this leads to an unbootable system as the
rescheduling IPI gets repeatedly repurposed for random drivers...
Instead, let's simply mark the level from which the hierarchy does
not make sense for the HW, and let the core code trim the usused
levels from the hierarchy.
Signed-off-by: Marc Zyngier <maz@kernel.org>
This set of changes fixes some minor issues in existing device trees and
adds ID EEPROMs on the Jetson Xavier NX. All ID EEPROMs are now labelled
to allow them to be detected by software.
It also adds support for the Tegra234 VDK board, which is a pre-silicon
platform for the upcoming Orin SoC.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAl9ky48THHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoVVtEACJcW6ztbQiqrksFdVW+8wlT/EZwNwr
qwwjGvy0ovJIYAPTB+XhGllUp17QR2EVzdGJW9Q8mr92QRpoQxSg3yB3BaJWsMoz
AH+9qkQoRE5F+aFwO2l8kTBDswyiOQCLxsiDSCcCWTHtvAQOl/K2HjG+4kxtko+C
0in+p67PG0t4qanjeTApWEWXjfiXBpM0bcv89TKK0SO+k+zsjupEZeOnVIbEpGTa
SMjKm/0l0jZIEMoweqX3H0jpTBvqE6IjLm4EAbCfLJrhDEIQe50WkNpw2CVaCZy6
2Mjnv7Gr/XO3MKmM4stLYTZ9eu5qDa7wGrQT/mXZt7kEc3L85rGZGyWQm5bCmspa
mSKZ+swtegkEBBofOabxcCDi0V9KxDiba3hwv4mr17qMjj7VBK5le3JhUS19qnZ8
Osu81JqKrDjfkmxtqSnJEeTTVwxBG09WQ5lME9FRBqH9P5Y1L7yCAuqPLzYhXxtj
KAcqveVzoMMi2YIp4Rt07seWsHhuNqkY9XWtPWrgubGtU1AKYXWHYDojefyo1VUq
1bOkzSa+ZVBwZuRmdgn2vxbeJnexeTAPolJp4WCpJpSGJbiFKNqhh5scjjfSviGS
PfOITtuJgaxoqEZRhCdF/VM2+YSjjVljRkiE6b8W0+eKkeQKzzDvJIDnOqeb7PGX
1gJniuIR25eShg==
=zeT7
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.10-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Changes for v5.10-rc1
This set of changes fixes some minor issues in existing device trees and
adds ID EEPROMs on the Jetson Xavier NX. All ID EEPROMs are now labelled
to allow them to be detected by software.
It also adds support for the Tegra234 VDK board, which is a pre-silicon
platform for the upcoming Orin SoC.
* tag 'tegra-for-5.10-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Initial Tegra234 VDK support
arm64: tegra: Populate EEPROMs for Jetson Xavier NX
arm64: tegra: Add label properties for EEPROMs
arm64: tegra: Add DT binding for AHUB components
arm64: tegra: Enable ACONNECT, ADMA and AGIC on Jetson Nano
arm64: tegra: Properly size register regions for GPU on Tegra194
arm64: tegra: Use valid PWM period for VDD_GPU on Tegra210
arm64: tegra: Describe display controller outputs for Tegra210
arm64: tegra: Disable SD card write-protection on Jetson Nano
arm64: tegra: Add VBUS supply for micro USB port on Jetson Nano
arm64: tegra: Wire up pinctrl states for all DPAUX controllers
arm64: tegra: Add ID EEPROMs on Jetson AGX Xavier
Link: https://lore.kernel.org/r/20200918150303.3938852-5-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
The NVIDIA Tegra234 VDK is a simulation platform for the Orin SoC. It
supports a subset of the peripherals that will be available in the final
chip and serves as a bootstrapping platform.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PMC block is largely similar to that found on earlier chips, but
not completely compatible. Allow binding to the instantiation found on
Tegra234.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move the definitions of reset sources and levels into a more natural
location.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The MISC block is largely similar to that found on earlier chips, but
not completely compatible. Allow binding to the instantiation found on
Tegra234.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for FUSE block found on the Tegra234 SoC, which is largely
similar to the IP found on previous generations.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function can be used by drivers to determine whether code is
running on silicon or on a simulation platform.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function extracts the PRE_SI_PLATFORM field from the HIDREV
register and can be used to determine which platform the kernel runs on
(silicon, simulation, ...). Note that while only Tegra194 and later
define this field, it should be safe to call this on prior generations
as well since this field should read as 0, indicating silicon.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PMIC wake event can be used to bring the system out of suspend based
on certain events happening on the PMIC (such as an RTC alarm).
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PMIC wake event can be used to bring the system out of suspend based
on certain events happening on the PMIC (such as an RTC alarm).
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
I have hit the following build error:
armv7a-hardfloat-linux-gnueabi-ld: drivers/soc/tegra/pmc.o: in function `pinconf_generic_dt_node_to_map_pin':
pmc.c:(.text+0x500): undefined reference to `pinconf_generic_dt_node_to_map'
armv7a-hardfloat-linux-gnueabi-ld: drivers/soc/tegra/pmc.o:(.rodata+0x1f88): undefined reference to `pinconf_generic_dt_free_map'
So SOC_TEGRA_PMC should select GENERIC_PINCONF.
Fixes: 4a37f11c8f ("soc/tegra: pmc: Implement pad configuration via pinctrl")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently the SoC revision attribute for Tegra devices displays the
value of the enum associated with a particular revision. This is not
very useful because to obtain the actual revision you need to
use the tegra_revision enumeration to translate the value.
It is more meaningful to display a name for the revision, such as
'A01', than the enumarated value and therefore, update the revision
attribute to display a name. This change does alter the ABI, which
is unfortunate, but this is more meaningful and maintable.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Clean-up the tegra_init_revision() function by removing the 'rev'
variable which is not needed and use the newly added helper function
tegra_get_minor_rev() to get the minor revision.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a custom SoC attribute for Tegra to expose the HIDREV register
fields to userspace via the sysfs. This register provides additional
details about the type of device (eg, silicon, FPGA, etc) as well as
revision. Exposing this information is useful for identifying the
exact device revision and device type.
For Tegra devices up until Tegra186, the majorrev and minorrev fields of
the HIDREV register are used to determine the device revision and device
type. For Tegra194, the majorrev and minorrev fields only determine the
revision. Starting with Tegra194, there is an additional field,
pre_si_platform (which occupies bits 20-23), that now determines device
type. Therefore, for all Tegra devices, add a custom SoC attribute for
the majorrev and minorrev fields and for Tegra194 add an additional
attribute for the pre_si_platform field.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PMIC wake event can be used to bring the system out of suspend based
on certain events happening on the PMIC (such as an RTC alarm).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
These changes implement various clocks that are controlled by the PMC
and add support for configuring the voltage level of some pins (needed
for example to support high-speed modes on the SD/MMC interfaces).
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAl5rtocTHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoSCxEACJ6z347KCFmlo2j2dy6IPzhwLUNfIu
MN+DxXzvgUPVslfYGp0AG0JCH6OKgFFnOiimJwgJaW573H3YC0+WybZjHZ4BgsJs
xy8x+aoLYikCJAA8A1fc+2F4g98Nw7sYpiRJc8Ry/fZmCsho4XGKEhNS2GqvuWGn
KQwah9M7ZgkJmb1eo4+Sxe7LfLpIBP+mG7nEI8CCr4DD1EF8c00dQ1xTUwQ4SOsU
Trc3Usonkhp7J4Oe82i8f1VqvS6+83+48FVP9PUsaf9LUEKMOhh/Z6XnEAH4ZVlq
q8oSpxY7AE0NrbjsgsN+hNeP9plQCv2XjmjD9xBk6C8y4drP8bMN2BVaRBBjoTHr
5R1br3HIKYNsgLJ7bYM3QvEN5Nk4gdT0wkpKVto12TKxYlxe+JRO5IeyJ17Jv0zH
yxMfyoHtqHgw3+Os3CtfVWgRs8egnN6W59C/vZxT02b7gqb89Ks80N4Y54bQEc1h
xqnT1NlPPvm4XctDzNKUz9EDoEb0KdblK/e9TnqFH9fbqE7QrwoPROSfv2wvXP6p
ej0GN1uIb9LPhTFSHX6Iu1EuAEuSwOFtEK2ZPHK4Ce2al03RQzsPQ/GCGIwxr1cM
+aGuURcAevR7Q8Tn8NB8xkI2l9p2dn3kMAgvqL1gcWi18eTJfRMgjejwcCZQds0C
mWEidGa+jrrNMQ==
=bszz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.7-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/soc
soc/tegra: Changes for v5.7-rc1
These changes implement various clocks that are controlled by the PMC
and add support for configuring the voltage level of some pins (needed
for example to support high-speed modes on the SD/MMC interfaces).
* tag 'tegra-for-5.7-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Cleanup whitespace usage
soc/tegra: pmc: Add pins for Tegra194
soc/tegra: Add support for 32 kHz blink clock
soc/tegra: Add Tegra PMC clocks registration into PMC driver
dt-bindings: usb: Add NVIDIA Tegra XUSB device mode controller binding
dt-bindings: phy: tegra-xusb: Add usb-role-switch
dt-bindings: phy: tegra: Add Tegra194 support
dt-bindings: soc: tegra-pmc: Add ID for Tegra PMC 32 kHz blink clock
dt-bindings: soc: tegra-pmc: Add Tegra PMC clock bindings
dt-bindings: tegra: Convert Tegra PMC bindings to YAML
dt-bindings: clock: tegra: Add IDs for OSC clocks
Link: https://lore.kernel.org/r/20200313165848.2915133-3-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Avoid using a mixture of tabs and spaces within tables to make them
easier to read and more consistently formatted.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Extend the Tegra194 IO pad table with additional information such as pin
names and 1.8/3.3 V settings to allow a table of voltage control pins to
generated from it. This is similar to what's done for older chips and is
needed to support high-speed modes for SDHCI where switching the pins to
1.8V or 3.3V is necessary.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra PMC has blink control to output 32 kHz clock out to Tegra blink
pin. Blink pad DPD state and enable controls are part of Tegra PMC
register space.
Currently Tegra clock driver registers blink control by passing PMC
address and register offset to clk_register_gate which performs direct
PMC access during clk_ops and with this when PMC is in secure mode, any
access from non-secure world does not go through.
This patch adds blink control registration to the Tegra PMC driver using
PMC specific clock gate operations that use tegra_pmc_readl() and
tegra_pmc_writel() to support both secure mode and non-secure
mode PMC register access.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra PMC has clk_out_1, clk_out_2, and clk_out_3 clocks and currently
these PMC clocks are registered by Tegra clock driver with each clock as
separate mux and gate clocks using clk_register_mux and clk_register_gate
by passing PMC base address and register offsets and PMC programming for
these clocks happens through direct PMC access by the clock driver.
With this, when PMC is in secure mode any direct PMC access from the
non-secure world does not go through and these clocks will not be
functional.
This patch adds these PMC clocks registration to pmc driver with PMC as
a clock provider and registers each clock as single clock.
clk_ops callback implementations for these clocks uses tegra_pmc_readl and
tegra_pmc_writel which supports PMC programming in both secure mode and
non-secure mode.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If only Tegra194 support is enabled, the tegra30_fuse_read() and
tegra30_fuse_init() function are not declared and cause a build failure.
Add Tegra194 to the preprocessor guard to make sure these functions are
available for Tegra194-only builds as well.
Link: https://lore.kernel.org/r/20200203143114.3967295-1-thierry.reding@gmail.com
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
Both Chip ID and strapping registers are now read out during of APB MISC
initialization, the registers' mapping isn't needed anymore once registers
are read. Hence let's unmap registers once they are not needed anymore,
for consistency.
Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Trying to read out Chip ID before APBMISC registers are mapped won't
succeed, in a result Tegra124 gets a wrong address for the HW straps
register if machine uses an old outdated device tree.
Fixes: 297c4f3dcb ("soc/tegra: fuse: Restrict legacy code to 32-bit ARM")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now both Chip ID and HW straps are becoming available at the same time,
thus we could simply check the availability of the ID in order to check
the availability of the straps. We couldn't check straps for 0x0 because
it could be a correct value.
This change didn't uncover any problems, but anyways it is nicer to have
straps verified for consistency with the Chip ID verification.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is no need to re-read Chip ID and HW straps out from hardware each
time, it is a bit nicer to cache the values in memory.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is no need to re-apply the same voltage. This change is just a minor
cleanup.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Fixes a regression for wake events on Tegra194 caused by the Tegra210
support that was added in v5.5-rc1 as well as wrong reset sources and
levels on Tegra194.
-----BEGIN PGP SIGNATURE-----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=Klyx
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.5-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
soc/tegra: Fixes for v5.5-rc1
Fixes a regression for wake events on Tegra194 caused by the Tegra210
support that was added in v5.5-rc1 as well as wrong reset sources and
levels on Tegra194.
* tag 'tegra-for-5.5-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Add reset sources and levels on Tegra194
soc/tegra: pmc: Add missing IRQ callbacks on Tegra194
soc/tegra: pmc: Use lower-case for hexadecimal literals
Link: https://lore.kernel.org/r/20191204130753.3614278-2-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo
-----BEGIN PGP SIGNATURE-----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=dk7w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
Tegra194 supports the same reset levels as Tegra186 but extends the set
of reset sources. Provide custom PMC register definitions to account for
the larger field for the reset sources as well as the updated list of
reset sources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
Changes in v2:
- use the new Tegra194 register definitions
Reuse the IRQ callbacks from Tegra186 on Tegra194. This fixes failures
to request interrupts on Tegra194 due to the missing callbacks.
Cc: Sowjanya Komatineni <skomatineni@nvidia.com>
Fixes: aba19827fc ("soc/tegra: pmc: Support wake events on more Tegra SoCs")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The remainder of the file uses lower-case for hexadecimal literals, so
change the only odd-one-out occurrence for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The removed barrier isn't needed because writes/reads are strictly ordered
and even if PMC had separate ports for writes, it wouldn't matter since
the hardware logic takes into effect after triggering CPU's power-gating
and at that point all CPU accesses are guaranteed to be completed. That
barrier was copied from the old arch/ code during transition to the soc/
PMC driver and even that the code structure was different back then, the
barrier didn't have a real useful purpose from the start. Lastly, the
tegra_pmc_writel() naturally inserts wmb() because it uses writel(),
and thus this change doesn't actually make any difference in terms of
interacting with hardware. Hence let's remove the barrier to clean up
code a tad.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
It is possible to get a lockup if kernel decides to enter LP2 cpuidle
from some clk-notifier, in that case CCF's "prepare" mutex is kept locked
and thus clk_get_rate(pclk) blocks on the same mutex with interrupts being
disabled, hanging machine.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Turned out that WFI doesn't work reliably on Tegra30 as a trigger for
the power-gating, it causes CPU hang under some circumstances like having
memory controller running of PLLP. The TRM doc states that WFI should be
used for the Big-Little "Cluster Switch", while WFE for the power-gating.
Hence let's use the WFE for CPU0 power-gating, like it is done for the
power-gating of a secondary cores. This fixes CPU hang after entering LP2
with memory running off PLLP.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add regulators coupler for Tegra30 SoCs that performs voltage balancing
of a coupled regulators and thus provides voltage scaling functionality.
There are 2 coupled regulators on all Tegra30 SoCs: CORE and CPU. The
coupled regulator voltages shall be in a range of 300mV from each other
and CORE voltage shall be higher than the CPU by N mV, where N depends
on the CPU voltage.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add regulators coupler for Tegra20 SoCs that performs voltage balancing
of a coupled regulators and thus provides voltage scaling functionality.
There are 3 coupled regulators on all Tegra20 SoCs: CORE, RTC and CPU.
The CORE and RTC voltages shall be in range of 170mV from each other and
they both shall be higher than the CPU voltage by at least 120mV. This
sounds like it could be handle by a generic voltage balancer, but the CORE
voltage scaling isn't implemented in any of the upstream drivers yet.
It will take quite some time and effort to hook up voltage scaling for
all of the drivers, hence we will use a custom coupler that will manage
the CPU voltage scaling for the starter.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 and prior Tegra chips have deep sleep entry and wakeup related
timings which are platform specific that should be configured before
entering into deep sleep.
Below are the timing specific configurations for deep sleep entry and
wakeup.
- Core rail power-on stabilization timer
- OSC clock stabilization timer after SOC rail power is stabilized.
- Core power off time is the minimum wake delay to keep the system
in deep sleep state irrespective of any quick wake event.
These values depends on the discharge time of regulators and turn OFF
time of the PMIC to allow the complete system to finish entering into
deep sleep state.
These values vary based on the platform design and are specified
through the device tree.
This patch has implementation to configure these timings which are must
to have for proper deep sleep and wakeup operations.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch configures polarity of the core power request signal
in PMC control register based on the device tree property.
PMC asserts and de-asserts power request signal based on it polarity
when it need to power-up and power-down the core rail during SC7.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch implements PMC wakeup sequence for Tegra210 and defines the
commonly used RTC alarm wake event.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch allows to create separate irq_set_wake and irq_set_type
implementations for different Tegra designs PMC that has different
wake models which require difference wake registers and different
programming sequence.
AOWAKE model support is available for Tegra186 and Tegra194 only
and it resides within PMC and supports tiered wake architecture.
Tegra210 and prior Tegra designs uses PMC directly to receive wake
events and coordinate the wake sequence.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Typically nvmem cells would be stored in device tree. However, for
compatibility with device trees that don't contain nvmem cell
definitions, register lookups for cells currently used by consumers.
This allows the consumers to use the same API to query cells from the
device tree or using the legacy mechanism.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The nvmem framework provides a generic infrastructure and API to access
the type of information stored in fuses such as the Tegra FUSE block.
Implement an nvmem device that can be used to access the information in
a more generic way to decouple consumers from the custom Tegra API and
to add a more formal way of creating the dependency between the FUSE
device and the consumers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Interrupts that don't have an associated wake event or GPIO wake events
end up with an associate IRQ chip that is NULL and which causes IRQ code
to crash. This is because we don't implicitly set the parent IRQ chip by
allocating the interrupt at the parent. However, there really isn't a
corresponding interrupt at the parent, so we need to work around this by
setting the special no_irq_chip as the IRQ chip for these interrupts.
Fixes: 19906e6b16 ("soc/tegra: pmc: Add wake event support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
tegra_fuse_readl() can be called from drivers at any time. If this API
is called before tegra_fuse_probe(), we end up enabling the clock before
it is registered. Add a check for the FUSE clock in tegra_fuse_readl()
and propagate any errors.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework
-----BEGIN PGP SIGNATURE-----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=ek+j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (84 commits)
reset: remove redundant null check on pointer dev
soc: rockchip: work around clang warning
dt-bindings: reset: imx7: Fix the spelling of 'indices'
soc: imx: Add i.MX8MN SoC driver support
soc: aspeed: lpc-ctrl: Fix probe error handling
soc: qcom: geni: Add support for ACPI
firmware: ti_sci: Fix gcc unused-but-set-variable warning
firmware: ti_sci: Use the correct style for SPDX License Identifier
soc: imx8: Use existing of_root directly
soc: imx8: Fix potential kernel dump in error path
firmware/psci: psci_checker: Park kthreads before stopping them
memory: move jedec_ddr.h from include/memory to drivers/memory/
memory: move jedec_ddr_data.c from lib/ to drivers/memory/
MAINTAINERS: Remove myself as qcom maintainer
soc: aspeed: lpc-ctrl: make parameter optional
soc: qcom: apr: Don't use reg for domain id
soc: qcom: fix QCOM_AOSS_QMP dependency and build errors
memory: tegra: Fix -Wunused-const-variable
firmware: tegra: Early resume BPMP
soc/tegra: Select pinctrl for Tegra194
...
- Add support in dmaengine core to do device node checks for DT devices and
update bunch of drivers to use that and remove open coding from drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
-----BEGIN PGP SIGNATURE-----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=R+aC
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Add support in dmaengine core to do device node checks for DT devices
and update bunch of drivers to use that and remove open coding from
drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
* tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: Revert "dmaengine: fsl-edma: add i.mx7ulp edma2 version support"
dmaengine: at_xdmac: check for non-empty xfers_list before invoking callback
Documentation: dmaengine: clean up description of dmatest usage
dmaengine: tegra210-adma: remove PM_CLK dependency
dmaengine: fsl-edma: add i.mx7ulp edma2 version support
dt-bindings: dma: fsl-edma: add new i.mx7ulp-edma
dmaengine: fsl-edma-common: version check for v2 instead
dmaengine: fsl-edma-common: move dmamux register to another single function
dmaengine: fsl-edma: add drvdata for fsl-edma
dmaengine: Revert "dmaengine: fsl-edma: support little endian for edma driver"
dmaengine: rcar-dmac: Reject zero-length slave DMA requests
dmaengine: dw: Enable iDMA 32-bit on Intel Elkhart Lake
dmaengine: dw-edma: fix semicolon.cocci warnings
dmaengine: sh: usb-dmac: Use [] to denote a flexible array member
dmaengine: dmatest: timeout value of -1 should specify infinite wait
dmaengine: dw: Distinguish ->remove() between DW and iDMA 32-bit
dmaengine: fsl-edma: support little endian for edma driver
dmaengine: hsu: Revert "set HSU_CH_MTSR to memory width"
dmagengine: pl330: add code to get reset property
dt-bindings: pl330: document the optional resets property
...
This contains a set of minor fixes and cleanups for core Tegra drivers.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAl0M61oTHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoYZAD/487VTni+jaefO8Vop87r1+nAbQNG9Y
i+QGdZwBTggHhE7rPKHMPPgmTqjAcTLezyM1kUx7nUF5eK4R/Rz1ND1MzutYt6/v
vS12SOfclPalZuO6DuR7vwCDeqpLy/WXFt4OZZzm/F/WxTBzc86BvOWSF7LvTXvl
kAK7TmOSUrItzvfyi/GPfdQsSZLg+3FWOwKf13Fp99n+/4IUDm+hdOeNaBnkvJSp
pLt0+bVctCp4i4VGwGzFw5kPVLLl/HotM8hEnAAlGr7bPXP+oEQAN0EYZIUirqM5
4HEYH2zkmK7ffy7FIARrvBKrE0krihtYFm931pCMzlQzzWGOfAOyoVwPCZq+Rg0R
yXpk8QSObc2o8ywnihfDYstiMToU9c8Et3IjpQUJ1hzH2kMofcJJ9PclVjSv7GWw
B9e6Fm14Za6Cp1Ec+X4VYJrWGI7dF8131Tsp0L7uVUk5ypqdV3rqv2hWnViZm72q
BBaTldmA5NzmBmwRWzxmRkFrl/WxsQQ2DN0NLIOJ4dUWn1MtCwZxvFuec/X3g8/f
dYwsKcFrG0oT+mYBBFZ7c7adpGTM2+hjuksolZPmRjGWRTPkjeISlbruG3UtWVuT
OhyUJDFQLpdenOTJJ9ZfVY5tgsItwibbTlhgKC4WFw/zd32Qs8fjIuPXrqzPIQHQ
jtbtAYYOp0r+cA==
=bqwE
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.3-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc: tegra: Changes for v5.3-rc1
This contains a set of minor fixes and cleanups for core Tegra drivers.
* tag 'tegra-for-5.3-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: Select pinctrl for Tegra194
soc/tegra: fuse: Do not log error message on deferred probe
soc/tegra: pmc: Add comments clarifying wake events
soc/tegra: pmc: Avoid crash for non-wake IRQs
soc/tegra: pmc: Fail to allocate more than one wake IRQ
Signed-off-by: Olof Johansson <olof@lixom.net>
tegra_powergate_sequence_power_up() powers up partition and also enables
clock & reset. However, if a controller like PCIe have multiple clocks
& resets and they need to be enabled in a sequence, driver must use
standalone function tegra_powergate_power_on() to power up partition.
Export tegra_powergate_power_on() to allow Tegra controller drivers to
unpower gate partition independent to clock & reset.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 33 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081038.745679586@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent changes have made it much more probable that clocks are not
available yet when the FUSE driver is first probed. However, that is a
situation that the driver can cope with just fine.
To avoid confusion, don't output an error when this happens.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add some comments to clarify the purpose of the wake event support
implemented in the PMC driver.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For interrupts that are not wakeup sources but that may end up getting
mapped through the PMC as interrupt parent (this can happen for GPIOs),
return early in order to avoid a subsequent crash from an out-of-bounds
access to the register region.
Reported-by: Bitan Biswas <bbiswas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The code currently doesn't support allocating more than one wake IRQ at
a time. Detect this situation and error out. Also make sure to output a
warning when that happens to help track down callers.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The __dma_request_channel() prototype has been changed to help to do
device node validation, thus we can use dma_request_channel() instead
of __dma_request_channel() to keep kernel bisectable.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
