IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
When a station is asleep, the fw will set it as "asleep".
All queues that are used only by one station will be stopped by
the fw.
In pre-DQA mode this was relevant for aggregation queues. However,
in DQA mode a queue is owned by one station only, so all queues
will be stopped.
As a result, we don't expect to get filtered frames back to
mac80211 and don't have to maintain the entire pending_frames
state logic, the same way as we do in aggregations.
The correct behavior is to align DQA behavior with the aggregation
queue behaviour pre-DQA:
- Don't count pending frames.
- Let mac80211 know we have frames in these queues so that it can
properly handle trigger frames.
When a trigger frame is received, mac80211 tells the driver to send
frames from the queues using release_buffered_frames.
The driver will tell the fw to let frames out even if the station
is asleep. This is done by iwl_mvm_sta_modify_sleep_tx_count.
Reported-and-tested-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The race happens when we send ADD_STA(auth->assoc) -> LQ_CMD
between the commands the FW sometimes loses the medium for AUX, and
sends a ndp to the AP and the flow becomes, ADD_STA -> send ndp -> LQ_CMD
the problem is that there's no rates yet defined for sending the ndp and
FW generates an assert.
The fix: change the order of the commands to LQ_CMD -> ADD_STA
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The session protection set for association is only removed when
BSS_CHANGED_BEACON_INFO is set and BSS_CHANGED_ASSOC is not set.
However, mac80211 may set both on association (in case a beacon was
already received). In this case, mac80211 will not set
BSS_CHANGED_BEACON_INFO on the next beacons because it has already
notified the beacon change, so the session protection is never removed
(until the session protection ends).
When a CSA is received within this time, the station will fail to
folllow the channel switch because it cannot schedule the time event.
Fix this by removing the session protection when
BSS_CHANGED_BEACON_INFO and BSS_CHANGED_ASSOC are both set.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A few of the static queues are enabled along with the bcast
STA. Make sure they are removed along with it, rather than
waiting for the mac ctxt release.
This is needed because we sometimes have a STA being removed
and then added again (either with the same sta_id or a
different one). If we wait for the mac ctxt release we will
try to allocate the queues again (as this is currently done
in the STA allocation and not in the MAC init) although
they weren't freed, and even if the sta_id of the STA has
changed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware will soon actually look at the AID field, and
when it does that it'll try to ensure that the AID is never
changing. Due to the way the station is added, it may start
with an invalid AID before it's associated, so to ensure a
constant AID (once it becomes non-zero), track the station
state and set the AID only when the station is associated
and when it disassociates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For a000 devices the INIT and RT images are unified to one
image.
The changes in the flow are the following:
* Driver load only RT firmware - meaning that the nvm access
command will be done in the RT image load flow.
* A new command (NVM_ACCESS_COMPLETE) now signals to the FW that
the driver is done accessing the NVM and FW can proceed with phy
calibrations.
* Phy DB is no longer sent from INIT FW to be restored by driver
for the RT FW - all the phy DB is now internal to the FW.
INIT complete will now follow the NVM access command, without
phy DB calls before.
* Paging command is sent earlier in the flow before NVM access
to enable a complete load of FW.
* caution must be care when restart is called since we may have
not completed init flow even though we are in RT firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The maximum number of firmware sections is now 32 instead of 16 for
a000 devices. Set the appropriate define. Avoid out of bounds access
in case there are more sections than the maximum set by driver.
Make the driver extensible to FW size changes by allocating the
section memory dynamically.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the relevant fields to export the 32-bit device timestamp to
radiotap using the new mac80211 infrastructure. This will be useful
to allow synchronising monitor captures taken on different hardware
simultaneously.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when configuring the cab queue the scheduler is configured
without station id - which results in station id 0.
In DQA mode this causes firmware to assert later on when the actual
station 0 is added with an empty tfd_queue_mask.
Fix that by configuring the queue to the broadcast station.
This is a bit trickier since the queue should not be included in the
tfd_queue_mask of the ADD_STA since it is a multicast queue, and the
tfd_queue_mask is only unicast queue. As a result the queue should be
enabled only after the broadcast station is added.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When using RSS on 9000 series devices, we can't rely on processing the
received frames for station powersave handling, since they could be
processed on different CPUs and out of order.
In order to still manage the powersave of stations, the firmware sends
a notification on sleep->wake, wake->sleep and - for U-APSD - frames
received with PM while already sleeping (with the TID.)
With this, the driver can set AP_LINK_PS, which is required for real
parallel RX. In addition, this requires checking for PS-Poll frames
and calling ieee80211_sta_pspoll() appropriately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we sync the RX queues the driver waits to receive echo
notification on all the RX queues.
The wait queue is set with timeout until all queues have received
the notification.
However, iwl_mvm_rx_queue_notif() never woke up the wait queue,
with the result of the counter value being checked only when the
timeout expired.
This may cause a latency of up to 1 second.
Fixes: 0636b938214c ("iwlwifi: mvm: implement driver RX queues sync command")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW versions older than -17 for 3160 and 7260 and older than -22 for
newer NICs are not supported anymore. Don't load these versions
and remove code that handles them.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement support for RRM by adding an option to configure the scan
dwell time and reporting scan start time and BSS detection time, and
Advertise support for these features.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
enable MU-MIMO air sniffer if it's supported by the NIC
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Major changes:
iwlwifi
* preparation for new a000 HW continues
* some DQA improvements
* add support for GMAC
* add support for 9460, 9270 and 9170 series
mwifiex
* support random MAC address for scanning
* add HT aggregation support for adhoc mode
* add custom regulatory domain support
* add manufacturing mode support via nl80211 testmode interface
bcma
* support BCM53573 series of wireless SoCs
bitfield.h
* add FIELD_PREP() and FIELD_GET() macros
mt7601u
* convert to use the new bitfield.h macros
brcmfmac
* add support for bcm4339 chip with modalias sdio:c00v02D0d4339
ath10k
* add nl80211 testmode support for 10.4 firmware
* hide kernel addresses from logs using %pK format specifier
* implement NAPI support
* enable peer stats by default
ath9k
* use ieee80211_tx_status_noskb where possible
wil6210
* extract firmware capabilities from the firmware file
ath6kl
* enable firmware crash dumps on the AR6004
ath-current is also merged to fix a conflict in ath10k.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJX2rF7AAoJEG4XJFUm622bD3EH/icZDT7vVxnb0VPP8jAScA4h
bMNrI3iFxnPohO8Rzp+edWSdxEZoxwrBVk/6BHXO9PHHZwPX7/b8/OOXmLWB2X1c
ffj1jt83RENcsZFvd5OJfDYxIq89uOkWybdD6nIUd3umKC9KeFOI5nCju31fEZrQ
ZptqvKGIV36bbx07K8Y/PQRL2SA6T+09WqvuljLHZD5hfPGZ+GWXV2p+HAm3Moos
iy6HUx5+pYfC+zlcmvJvL47Wxj+HppS/48ujyQ68DD2UkjOtF620YJjVy3o+njip
GNJtCgWFDp2ar3uvRP2BfBd9FtseDTKsKusxJQvNGoSR0ON+uGIzURCznQ+2PCM=
=FyXw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-09-15' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.9
Major changes:
iwlwifi
* preparation for new a000 HW continues
* some DQA improvements
* add support for GMAC
* add support for 9460, 9270 and 9170 series
mwifiex
* support random MAC address for scanning
* add HT aggregation support for adhoc mode
* add custom regulatory domain support
* add manufacturing mode support via nl80211 testmode interface
bcma
* support BCM53573 series of wireless SoCs
bitfield.h
* add FIELD_PREP() and FIELD_GET() macros
mt7601u
* convert to use the new bitfield.h macros
brcmfmac
* add support for bcm4339 chip with modalias sdio:c00v02D0d4339
ath10k
* add nl80211 testmode support for 10.4 firmware
* hide kernel addresses from logs using %pK format specifier
* implement NAPI support
* enable peer stats by default
ath9k
* use ieee80211_tx_status_noskb where possible
wil6210
* extract firmware capabilities from the firmware file
ath6kl
* enable firmware crash dumps on the AR6004
ath-current is also merged to fix a conflict in ath10k.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for installing and removing GMAC key
for newer FW versions that support GCM and MFP.
GMAC provides authentication and integrity for multicast management
frames.
Firmware API was changed, update the driver accordingly.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwlmvm driver supports channel width change in AP mode. Add the
proper flag.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for the v4 version of the TX power command. Just add a
new version and do the same sizing tricks that were done when support
for v3 was introduced.
This patch doesn't support the new functionality introduced, but makes
the driver work with the new size of the command.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to reduce reliance on mac80211 structs in the core
iwlwifi code, store the cipher schemes in the format given
by the firmware and convert it later, rather than storing it
in the mac80211 format.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We removed support for old API for coexistence, but we
forgot to remove defines and variable that are not needed
anymore.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For 9000 family we will get extended statistics notification
with averaged data for RSSI, TCM and rogue AP detection.
Support it. Future patches will added the required algorithms.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer hardware supports GCMP and GCMP 256-bit ciphers.
Add support for adding/setting GCMP key for TX mode.
In the TX command handling GCMP-256 is handled in a different
way as the key size should be up to 128-bits:
Set the key value to the key index in the key table,
and specify that this key should be taken form the key table
instead of from the TX command.
While at it - convert security control flags to an enum.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some transports may sleep when writing to registers, which is done
when calling iwl_force_nmi(). So we can't call iwl_force_nmi() in a
timer context. To solve that, convert the scan timeout timer to a
delayed work.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support CSA countdown offloading. When CSA starts, the driver
specifies the offsets to the eCSA and CSA IEs in the beacon template
command and the fw performs the countdown.
The fw notifies the driver when the channel switch flow
should be performed.
Beacon sent notifications are not used anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Ucode capability bit 26 indicates support for UAPSD on P2P interface
even with a simultaneous BSS station interface, as long as both
interfaces are in the same binding. Change the name of the
capability bit to reflect that.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
My cleanup in "iwlwifi: prepare for higher API/CAPA bits" accidentally
inverted a few tests - fix them.
Fixes: 859d914c8f5c ("iwlwifi: prepare for higher API/CAPA bits")
Reported-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In non-shared queues, DQA requires re-configuring existing
queues to become aggregated rather than allocating a new
one. It also requires "un-aggregating" an existing queue
when aggregations are turned off.
Support this requirement for non-shared queues.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently code allows mvm reference to become negative and
only warns in case mvm reference is released while reference
counting is 0.
However, we better prevent this from happening at all since
iwl_mvm_unref() may race against iwl_mvm_unref_all_except()
which is called on restart.
As a result we might get the same reference unreferenced twice
ending with a negative value:
An example for an easily reproduced log:
[ 2689.909166] iwl_mvm_ref Take mvm reference - type 8
[ 2690.732716] iwl_mvm_unref_all_except Cleanup: remove mvm ref type 8 (1)
[ 2690.849708] iwl_mvm_unref Leave mvm reference - type 8
[ 2690.849721] WARNING: ... iwl_mvm_unref+0xb0/0xc0 [iwlmvm]()
If there will be yet another another restart iwl_mvm_unref_all_except
will run from 0 up to ref count, and since it is unsigned, we will throw
the transport ref count completely out of balance:
iwl_mvm_unref_all_except[I] -- Cleanup: remove mvm ref type 8 (255)
iwl_trans_slv_unref[I] -- rpm counter: 0
iwl_trans_slv_unref[I] -- rpm counter: -1
iwl_trans_slv_unref[I] -- rpm counter: -2
...
iwl_trans_slv_unref[I] -- rpm counter: -253
iwl_trans_slv_unref[I] -- rpm counter: -254
As there is no valid scenario where we can get to a negative
reference count - prevent it from happening.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order for mac80211 to use per-CPU statistics for RSS RX, the
driver needs to advertise that it uses RSS. Do this when using
more than a single queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Next hardware will direct packets to core based on the TCP/UDP
streams.
This logic can create holes in reorder buffer since packets that
belong to other stream were directed to a different core.
However, those are valid holes and the packets can be indicated
in L3 order.
The hardware will utilize a mechanism of informing the driver of
the normalized ssn and the driver shall release all packets that
SN is lower than the nssn.
This enables managing the reorder across the queues without sharing
any data between them.
The reorder buffer is allocated and released directly in the RX path
in order to avoid various races between control path and rx path.
The code utilizes the internal messaging to notify rx queues of when
to delete the reorder buffer.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
According to the spec when a BA session is started there
is a timeout set for the session in the ADDBA request.
If there is not activity on the TA/TID then the session
expires and a DELBA is sent.
In order to check for the timeout, data must be shared
among the rx queues.
Add a timer that runs as long as BA session is active
for the station and stops aggregation session if needed.
This patch also lays the infrastructure for the reordering
buffer which will be enabled in the next patches.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the sync notification is a type of notification. However, it
is better fitted as an attribute of a notification, since there might
be another message in the payload (delba for instance) that should be
sent while control path is waiting for all queues to process.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
mac80211 will call the driver whenever there is a race between
RSS queues and control path that requires a processing of all
pending frames in RSS queues.
Implement that by utilizing the internal notification mechanism:
queue a message to all queues. When the message is received on
a queue it decrements the atomic counter. This guarantees that
all pending frames in the RX queue were processed since the message
is in order inside the queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Declare and enable support of RX and TX checksum for 9000 family.
Configure offload_assist in the TX cmd accordingly to support
TX csum.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
"DQA" is shorthand for "dynamic queue allocation". This
enables on-demand allocation of queues per RA/TID rather than
statically allocating per vif, thus allowing a potential
benefit of various factors.
Please refer to the DOC section this patch adds to sta.h to
see a more in-depth explanation of this feature.
There are many things to take into consideration when working
in DQA mode, and this patch is only one in a series. Note that
default operation mode is non-DQA mode, unless the FW
indicates that it supports DQA mode.
This patch enables support of DQA for a station connected to
an AP, and works in a non-aggregated mode.
When a frame for an unused RA/TID arrives at the driver, it
isn't TXed immediately, but deferred first until a suitable
queue is first allocated for it, and then TXed by a worker
that both allocates the queues and TXes deferred traffic.
When a STA is removed, its queues goes back into the queue
pools for reuse as needed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to disable uapsd for BSS only, or P2P client
separately. Remove the now unneeded
IWL_MVM_P2P_UAPSD_STANDALONE constant.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
LQM stands for Link Quality Measurement. The firmware
will collect a defined set of statitics (see the
notification for details) that allow to know how busy
the medium is. The driver issues a request to the firmware
that includes the duration of the measurement (the firmware
needs to be on channel for that amount of time) and the
timeout (in case the firmware has a lot of offchannel
activities). If the timeout elapses, the firmware will
send partial results which are still valuable.
In case of disassociation / channel switch and alike, the
driver is in charge of stopping the measurements and the
firmware will reply with partial results.
The user space API for now is debugfs only and will be
implmemented in an upcoming patch.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently paging download buffer is freed during the
the unloading of the opmode which happens when the driver
is unloaded.
This causes a memory leak since the paging download
buffer is allocated every time we enable the
interface, so the download buffer can be allocated many
times, but only be freed once.
Free paging download buffer during disabling of the
interface.
CC: stable@vger.kernel.org [4.3+]
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware/hardware only supports checking AES-CMAC on RX, not
using it on TX. For station mode this is fine, since it's the only
thing it will ever do. For AP mode, it never receives such frames,
but must be able to transmit them. This is currently broken since
we try to enable them for hardware crypto (for RX only) and then
treat them as TX_CMD_SEC_EXT, leading to FIFO underruns during TX
so the frames never go out to the air.
To fix this, simply use software on TX in AP (and IBSS) mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Before authentication, we start a time event during
which we wait for a beacon in order to sync our timers.
If we didn't hear the beacon during this time - we abandon
the connection. However, in congested environment, it was
observed we might not hear beacons in that time slot.
Extend the time event to give the connection a better chance.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Leaving ucode_loaded to true after stop_device() has been called
is a recipe for problems. Flows that are not sync'ed with the
driver life cycle (like debugfs hooks and thermal hooks) must
check that the firmware is loaded before they interact with it.
Therefore we need to keep this variable updated with the real
status of the firmware.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Beacon abort (ba) is set while sending power command, but only
after at least one beacon_filter command was successfully sent.
If we heard a beacon before starting association, this order
is maintained and ba is properly set.
However, if the first beacon is received after association,
we send the power command upon association, configure the
beacon filtering when the first beacon arrives, and in that case,
beacon abort is not set.
So identify this, and send a power command post the beacon_filter
command if needed.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Older versions of the firmware don't support U-APSD for
P2P Client. Forbid U-APSD for P2P Client when an old
firmware is being used.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow to publish RRM capabilities without the need to support a minimal
capability set. Since some RRM features(e.g. neighbor report) are fw
independent, set this capability unconditionally.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* Remove uneeded includes:
iwl-csr.h and devcoredump aren't used in mac80211.c.
* Remove uneeded empty line
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
