IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Add support for pshold block to drive pshold towards the PMIC, which is
used to trigger a configurable event such as reboot or poweroff of the
SDX55 platform.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210118051005.55958-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The BreadBee and the BreadBee Crust are the same PCB with a different
SoC mounted. There are two top level dts to handle this.
To avoid deduplicating the parts that are more related to the PCB than
the SoC (i.e. the voltage regs and LEDs) add a common dtsi that can
be included in both top level dts.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20201224020354.2212037-1-daniel@0x0f.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- removing a property never documented nor used
- adding i2c recovery GPI for one more board
-----BEGIN PGP SIGNATURE-----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=SfGI
-----END PGP SIGNATURE-----
Merge tag 'at91-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt
AT91 DT for 5.12:
- removing a property never documented nor used
- adding i2c recovery GPI for one more board
* tag 'at91-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d2: remove atmel,wakeup-type references
ARM: dts: at91-sama5d27_wlsom1: add i2c recovery
Link: https://lore.kernel.org/r/20210122145056.171283-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since commit fa2d0aa96941 ("mmc: core: Allow setting slot index
via device tree alias") proper aliases should be named "mmcN".
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Link: https://lore.kernel.org/r/20210110185835.133059-1-alexeymin@postmarketos.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Ericsson U300 platform was one of two ARM929 based SoC platforms for
mobile phones in ST-Ericsson after the merger of Ericsson with ST-NXP
into ST-Ericsson, the other one being the ST Nomadik.
The platform was not widely adopted in Linux based systems and was
replaced with the far superior ST-Ericsson U8500 in 2011, but Linus
Walleij kept maintaining the code for the whole time.
Linus continues to use the Nomadik machine, but decided to drop
u300 from the kernel as part of this year's spring cleaning.
Thanks for having maintained it all these years.
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/lkml/CACRpkdbJkiHR9FSfJTH_5d_qRU1__dRXHM1TL40iqNRKbGQfrQ@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The smp8758 (tango4) SoC was the last generation of set-top-box chips
to come out of Sigma Designs, and support was added by Marc Gonzalez
and Måns Rullgård between 2015 and 2017, before the company went out of
business and the products were abandoned.
The chip is used in some set-top-boxes such as the Popcorn Hour A-500,
which could have seen some adoption by hobbyists. This has not happened
in the past four years, and support for the more widely used MIPS based
SoCs was never merged at all.
Thanks to Marc and Måns for maintaining for the past years even after the
death of the platform.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Link: https://lore.kernel.org/lkml/2d643ebc-09af-a809-eb3f-2aec8ecee501@free.fr/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ZTE ZX set-top-box SoC platform was added in 2015 by Jun Nie, with
Baoyou Xie and Shawn Guo subsequently becoming maintainers after the
addition of the 64-bit variant.
However, the only machines that were ever supported upstream are the
reference designs, not actual set-top-box devices that would benefit
from this support. All ZTE set-top-boxes from the past few years seem
to be based on third-party SoCs. While there is very little information
about zx296702 and zx296718 on the web, I found some references to other
chips from the same family, such as zx296716 and zx296719, which were
never submitted for upstream support. Finally, there is no support for
the GPU on either of them, with the lima and panfrost device drivers
having been added after work on the zx platform had stopped.
Shawn confirmed that he has not seen any interest in this platform for
the past four years, and that it can be removed.
Thanks to Jun and Shawn for maintaining this platform over the past
five years.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The SiRF Prima2 and Atlas platform code was contributed by Cambridge
Silicon Radio (CSR) after aquiring the original SiRF company, and
maintained by Barry Song. CSR was subsequently acquired by Qualcomm,
who no longer have an interest in maintaining the SoC platform but
instead have released more recent SoCs for the same market in the
Snapdragon family.
As Barry is no longer working for the company, nobody else there
wants to maintain it, and there are no third-party users, the
best way forward seems to be to completely remove it.
Thanks to Barry for maintaining the platform for the past ten years.
Cc: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/lkml/c969392572604b98bcb3be44048c3165@hisilicon.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A test with the command below gives for example this error:
/arch/arm/boot/dts/rk3288-tinker.dt.yaml:
thermal-zones: 'cpu_thermal', 'gpu_thermal', 'reserve_thermal'
do not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
Rename Rockchip rk3288 thermal subnodes
so that it ends with "-thermal"
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
thermal/thermal-zones.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210117150953.16475-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The CPU thermal zone is called on most of the older DTSI cpu_thermal.
However, the underscore is an invalid character for a node name and the
thermal zone binding explicitly requires that zones are called
*-thermal. Let's fix it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-8-maxime@cerno.tech
The pwm-backlight binding requires a power supply. Make sure we provide
one.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-7-maxime@cerno.tech
According to the LED bindings, the LED node names are supposed to be led
plus an optional suffix. Let's fix our users to use that new scheme.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210114113538.1233933-6-maxime@cerno.tech
Here are few more late changes that would be nice to get into v5.11:
- More updates to use cpsw switchdev driver
- Enable gta04 PMIC power management
- Updates for dra7 for ECC support, 1.8GHz speed and keep the
ldo0 regulator always on as specified in the data manual
-----BEGIN PGP SIGNATURE-----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=XKaK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.11/dt-late-signed' into omap-for-v5.12-dt
Late devicetree changes for omaps for v5.11 merge window
Here are few more late changes that would be nice to get into v5.11:
- More updates to use cpsw switchdev driver
- Enable gta04 PMIC power management
- Updates for dra7 for ECC support, 1.8GHz speed and keep the
ldo0 regulator always on as specified in the data manual
The PHY address bit 2 is configured by the LED pin. Attaching a LED
to this pin is not sufficient to guarantee this configuration pin is
correctly read. This leads to some platforms having their PHY at
address 0 and others at address 4.
If there is no phy-handle specified, the FEC driver will scan the PHY
bus for a PHY and use that. Consequently, adding the DT configuration
of the PHY and the phy properties to the FEC driver broke some boards.
Fix this by removing the phy-handle property, and listing two PHY
entries for both possible PHY addresses, so that the DT configuration
for the PHY can be found by the PHY driver.
Fixes: 86b08bd5b994 ("ARM: dts: imx6-sr-som: add ethernet PHY configuration")
Reported-by: Christoph Mattheis <christoph.mattheis@arcor.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is another uart next to the console uart used by vendor uboot and
kernel, enable it and document its location.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Configuration was correct enough to work with the pre-configuration done by
uboot. While at it, also document the location.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is another uart next to the console uart used by vendor uboot and
kernel, enable it and document its location.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Configuration was correct enough to work with the pre-configuration done by
uboot. While at it, also document the location.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RTC pcf2127 device driver has changed default behaviour of the watchdog
feature in v5.11-rc1. Now you need to explicitly enable it with a
device tree property, "reset-source", when used in the board design.
Fixes: 71ac13457d9d ("rtc: pcf2127: only use watchdog when explicitly available")
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Cc: Bruno Thomsen <bth@kamstrup.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
VICTGO is the Kverneland TGO IsoBus universal terminal for agricultural
applications on tractors
Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
VICUT1(Q,P) is the Kverneland UT1(Q,P) IsoBus universal terminal for agricultural
applications on tractors.
Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a device-tree definition for the CSI0 MCLK pin,
which can be used for feeding MIPI CSI-2 sensors.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
There are two KSZ8081 on the imx6ul-14x14-evk: one has the reset line
controlled by the Q1 output of the 74LV595PW expander, and the other
by the Q2 output.
The KSZ8081 datasheet states that the tsr parameter (Stable supply
voltage (VDDIO, VDDA_3.3) to reset high) to be 10ms minimum and
"After the de-assertion of reset, wait a minimum of 100 µs before
starting programming on the MIIM (MDC/MDIO) interface."
Describe these parameters in the devicetree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the 74LV595PW GPIO expander is not functional because its OE
pin is not driven low.
Make it funcional by passing the 'enable-gpios' property inside the
GPIO expander node.
After putting the OE pin in low state, the outputs of the 74LV595PW all
go low.
The two KSZ8081 Ethernet PHYs reset lines are driven from the
the GPIO expander and as they remain low, this causes the Ethernet
PHYs not to be detected.
There is one solution to this problem as suggested by Andrew Lunn:
"Some devices will respond to MDIO while held in reset, some don't.
If your PHYs don't you need to add a compatible of the form
ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$ with the PHY ID. The PHY
will then be probed, independent of if it can be found on the bus or
not, and that probing will enable the GPIO."
So pass the "ethernet-phy-id0022.1560" for the KSZ8081 PHYs so that they
both can be functional after 74LV595PW is activated.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GPIO expander SPI chipselect is active low. Mark it as such to avoid
the following warning:
[ 6.839213] gpio@0 enforce active low on chipselect handle
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no firmware to initialize the arch timer register on all iMX7
systems, add arm,cpu-registers-not-fw-configured to let Linux do it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Ux500 platforms have some memory carveouts set aside for
communicating with the modem and for the initial secure software
(ISSW). These areas are protected by the memory controller
and will result in an external abort if accessed like common
read/write memory.
On the legacy boot loaders, these were set aside by using
cmdline arguments such as this:
mem=96M@0 mem_mtrace=15M@96M mem_mshared=1M@111M
mem_modem=16M@112M mali.mali_mem=32M@128M mem=96M@160M
hwmem=127M@256M mem_issw=1M@383M mem_ram_console=1M@384M
mem=638M@385M
Reserve the relevant areas in the device tree instead. The
"mali", "hwmem", "mem_ram_console" and the trailing 1MB at the
end of the memory reservations in the list are not relevant for
the upstream kernel as these are nowadays replaced with
upstream technologies such as CMA. The modem and ISSW
reservations are necessary.
This was manifested in a bug that surfaced in response to
commit 7fef431be9c9 ("mm/page_alloc: place pages to tail in __free_pages_core()")
which changes the behaviour of memory allocations
in such a way that the platform will sooner run into these
dangerous areas, with "Unhandled fault: imprecise external
abort (0xc06) at 0xb6fd83dc" or similar: the real reason
turns out to be that the PTE is pointing right into one of
the reserved memory areas. We were just lucky until now.
We need to augment the DB8500 and DB8520 SoCs similarly
and also create a new include for the DB9500 used in the
Snowball since this does not have a modem and thus does
not need the modem memory reservation, albeit it needs
the ISSW reservation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Cc: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20201213225517.3838501-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
#pwm-cells conversion.
- Fix duplicated bus node name for i.MX8MN SoC.
- Fix reset register offset on LS1028A SoC.
- Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
index consistent with previous kernel version.
- Selecting ARM_GIC_V3 on non-CP15 processors to fix one build failure
with i.MX8M SoC driver.
- Fix typos with status property on imx6qdl-kontron-samx6i board.
- Fix duplicated regulator-name on imx6qdl-gw52xx board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl/9n4AUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5pmQf+O0hRAVWaMXk4SCs/CsQ4Z6XNPSfz
7DSnkz0Rg53uykv+oe57sryBHGI46vy/hJeD6/OX4XgnlxaKXwmdaE+sek85D01h
C/Gzg7lKDvr8vWKZcOzhTQhs9F+EuHSsS2zW9StUBBSlXx3r2h9f+kJOLihFwvQp
CCWU+eGXgRIqZme5tIX9tFqPP1PmNRfIbZWgLwx9e/foCMl64fJSIe45ik4WePeV
+WCB3xMP38q2bfhZQv164uIw8m5/nEb8dp9O+zNamy/RN1hQqRaq1sPAwrjcqs2z
whaVS3iaGRM/RyAdbxy1JCxM+yDNM0Vnby/txVgsEOE+a9mfl2D2upQ1NA==
=+e1G
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.11:
- Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
#pwm-cells conversion.
- Fix duplicated bus node name for i.MX8MN SoC.
- Fix reset register offset on LS1028A SoC.
- Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
index consistent with previous kernel version.
- Selecting ARM_GIC_V3 on non-CP15 processors to fix one build failure
with i.MX8M SoC driver.
- Fix typos with status property on imx6qdl-kontron-samx6i board.
- Fix duplicated regulator-name on imx6qdl-gw52xx board.
* tag 'imx-fixes-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-gw52xx: fix duplicate regulator naming
ARM: dts: imx6qdl-kontron-samx6i: fix i2c_lcd/cam default status
ARM: imx: fix imx8m dependencies
ARM: dts: tbs2910: rename MMC node aliases
arm64: dts: ls1028a: fix the offset of the reset register
arm64: dts: imx8mn: Fix duplicate node name
ARM: dts: imx6qdl-kontron-samx6i: fix pwms for lcd-backlight
Link: https://lore.kernel.org/r/20210112131224.GI28365@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I didn't touch this code since it served as a platform to introduce
ARMv7-M support to Linux. The only known machine that runs Linux has only
4 MiB of RAM (that originally only exists to hold the display's framebuffer).
There are no known users and no further use foreseeable, so drop the
code.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210115155130.185010-2-u.kleine-koenig@pengutronix.de'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PicoITX has only one ethernet routed out, so the KS8851 is not used
at all. Disable the KS8851 and the entire FMC controller.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The node names for devices using the pwm-leds driver follow a certain
naming scheme (now). Parent node name is not enforced, but recommended
by DT project.
DTC arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml
CHECK arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml: led-rgb: 'led-blue', 'led-green', 'led-red' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
Signed-off-by: Alexander Dahl <post@lespocky.de>
Acked-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.
Fixes: fde180f06d7b ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Due to a change in gpiolib-of.c, setting flags to GPIO_ACTIVE_LOW and
using output-low DT property leads to the GPIO being set high instead.
Fixes: ac68793f49de ("ARM: dts: stm32: Add DHCOM based PicoITX board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The GPIO hog node name should match regex '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$',
make it so and fix the following two make dtbs_check warnings:
arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dt.yaml: hog-usb-port-power: $nodename:0: 'hog-usb-port-power' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dt.yaml: hog-usb-hub: $nodename:0: 'hog-usb-hub' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
Fixes: ac68793f49de ("ARM: dts: stm32: Add DHCOM based PicoITX board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The DRC02 has no use for the on-SoM touchscreen controller, and the
on-SoM touchscreen controller may not even be populated, which then
results in error messages in kernel log. Disable the touchscreen
controller in DT.
Fixes: fde180f06d7b ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
