IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Some device only support 4 TCs, but the driver check the total
bandwidth of 8 TCs, so may cause wrong configurations write to
the hw.
This patch uses hdev->tc_max to instead HNAE3_MAX_TC to fix it.
Fixes: e432abfb99e5 ("net: hns3: add common validation in hclge_dcb")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a TC's PFC is disabled or enabled, the RX private buffer for
this TC need to be changed too, otherwise this may cause packet
dropped problem.
This patch fixes it by calling hclge_buffer_alloc to reallocate
buffer when pfc_en changes.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, hns3 driver just directly send specific setting bit
and mask bits of MAC VLAN switch parameter to the firmware, it
can not be compatible with the old firmware, because the old one
ignores mask bits and covers all bits with new setting bits.
So when running with old firmware, the communication between PF
and VF will fail after resetting or configuring spoof check, since
they will do the MAC VLAN switch parameter configuration.
This patch fixes this problem by reading switch parameter firstly,
then just modifies the corresponding bit and sends it to firmware.
Fixes: dd2956eab104 ("net: hns3: not allow SSU loopback while execute ethtool -t dev")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-allocates buffers sufficient for the maximum supported MTU (2026) in
order to eliminate the possibility of resource exhaustion when changing the
MTU while the device is up.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAl3NINITHG1rbEBwZW5n
dXRyb25peC5kZQAKCRBaxiGjkeSdIMjLB/98vM52VE23+bTCgsu48/7/nosfAfJl
ciQGUjDt4Rd0ZbNLjfFH0+rr7+vt7pjHban9anG48xWGAoudKKKv4tpWWs/BLiF4
F7vaOS83LKcKUea5k8us91OkrMZn8CeXRLCQVw8U2bcvk6H28U6MHgyEM/AJwVIL
iWfVwcUrxQEEwcvB0v29ymdmGXixd6/EfsLhnxiPgGhDeiNyQ34cmT5j6hYO4Mjf
9iuapLhVkrkiCB6Ck3EPP2M6yL1DRimRo5UmgN9DIEVCdapKfQ354F1XkdYAIVob
oar1SD2LUREF/N1Zn7fnFtm3rFxBSa+LGPDCbBNKuXqqrOKMbAOdYStB
=qlbm
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.4-20191114' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-11-14
here another pull request for net/master consisting of one patch (including my S-o-b).
Jouni Hogander's patch fixes a memory leak found by the syzbot in the slcan
driver's error path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hopefully last fixes for v5.4, only one iwlwifi fix this time.
iwlwifi
* fix A-MSDU data corruption when using CCMP/GCMP ciphers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdzR3vAAoJEG4XJFUm622b6+4H/25TWvWesjFia+z7he1azhUi
OURdehcl84b+VqM9kUhajsJGe9xOpy6vCTW5TUPijxw7a0Yg0IGIPDd4ITLZlJJT
UHIjQaOPvpow3avM5Lia/8Japa9DnVeYVxVbVWy6jwV/20ymuWcGhbwHtFcwUYEj
yx7+yKP8q0Ip4lBOys97SlUJPlMc/EUaKa8VMg4k02Wyq3Wmx4uBW97F8mQIjDG3
rVesipFOoKSQYnJm87dwk2jV9h7gmXrVXtP5+kV3899W/pW8Jg8OcvSrdnTht92h
VnxpGrJK2HZXgVbKHqzuILfG9WZi7DNep9ZyQH815Y8tiFFfRSt7Gf5aiRwWmv8=
=4/Qt
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2019-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.4
Hopefully last fixes for v5.4, only one iwlwifi fix this time.
iwlwifi
* fix A-MSDU data corruption when using CCMP/GCMP ciphers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is supposed to test for negative error codes and partial
reads, but because sizeof() is size_t (unsigned) type then negative
error codes are type promoted to high positive values and the condition
doesn't work as expected.
Fixes: 332f989a3b00 ("CDC-NCM: handle incomplete transfer of MTU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setup_dpio() function tries to allocate a number of channels equal
to the number of CPUs online. When there are not enough DPCON objects
already probed, the function will return EPROBE_DEFER. When this
happens, the already allocated channels are not freed. This results in
the incapacity of properly probing the next time around.
Fix this by freeing the channels on the error path.
Fixes: d7f5a9d89a55 ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coccinelle warning:
./drivers/net/phy/mdio_bus.c:67:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62
./drivers/net/phy/mdio_bus.c:68:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62
Fix this by using IS_ERR before PTR_ERR
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 71dd6c0dff51 ("net: phy: add support for reset-controller")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call devlink enable only during probe time and avoid deadlock
during reload.
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Fixes: 5a508a254bed ("devlink: disallow reload operation during device cleanup")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PHY is not powered, the probe function fail and some resource are
still unallocated.
Furthermore some BUG happens:
dwmac-sun8i 5020000.ethernet: EMAC reset timeout
------------[ cut here ]------------
kernel BUG at /linux-next/net/core/dev.c:9844!
So let's use the right function (stmmac_pltfr_remove) in the error path.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/bind
devlink dev reload pci/0000:00:10.0 &
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/unbind
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4e7 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2019-11-08
This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice
drivers.
Colin Ian King fixes a potentially wrap-around counter in a for-loop.
Nick fixes the default ITR values for the iavf driver to 50 usecs
interval.
Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value
cannot be obtained from the firmware, so add X722 to the check to ensure
the wrong value is not returned.
Jake fixes igb and igc drivers in their implementation of launch time
support by declaring skb->tstamp value as ktime_t instead of s64.
Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may
not be set for AF_XDP sockets that are only used to send packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.
Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.
Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.
This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains fix for a problem with command:
'ethtool -m <dev>'
which breaks functionality of:
'ethtool <dev>'
when called on X722 NIC
Disallowed update of link phy_types on X722 NIC
Currently correct value cannot be obtained from FW
Previously wrong value returned by FW was used and was
a root cause for incorrect output of 'ethtool <dev>' command
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 92418fb14750 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.
Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.
This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the for-loop counter i is a u8 however it is being checked
against a maximum value hw->num_tx_sched_layers which is a u16. Hence
there is a potential wrap-around of counter i back to zero if
hw->num_tx_sched_layers is greater than 255. Fix this by making i
a u16.
Addresses-Coverity: ("Infinite loop")
Fixes: b36c598c999c ("ice: Updates to Tx scheduler code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
From gen2 PN is totally offloaded to hardware (also the space for the
IV isn't part of the skb). As you can see in mvm/mac80211.c:3545, the
MAC for cipher types CCMP/GCMP doesn't set
IEEE80211_KEY_FLAG_PUT_IV_SPACE for gen2 NICs.
This causes all the AMSDU data to be corrupted with cipher enabled.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Octeon's input ring-buffer entry has 14 bits-wide size field, so to account
for second possible VLAN header max_mtu must be further reduced.
Fixes: 109cc16526c6d ("ethernet/cavium: use core min/max MTU checking")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the problem of the spin locks, originally
meant for the netpoll path of hns driver, causing deadlock in
the normal NAPI poll path. The issue happened due to the presence
of the stray leftover spin lock code related to the netpoll,
whose support was earlier removed from the HNS[1], got activated
due to enabling of NET_POLL_CONTROLLER switch.
Earlier background:
The netpoll handling code originally had this bug(as identified
by Marc Zyngier[2]) of wrong spin lock API being used which did
not disable the interrupts and hence could cause locking issues.
i.e. if the lock were first acquired in context to thread like
'ip' util and this lock if ever got later acquired again in
context to the interrupt context like TX/RX (Interrupts could
always pre-empt the lock holding task and acquire the lock again)
and hence could cause deadlock.
Proposed Solution:
1. If the netpoll was enabled in the HNS driver, which is not
right now, we could have simply used spin_[un]lock_irqsave()
2. But as netpoll is disabled, therefore, it is best to get rid
of the existing locks and stray code for now. This should
solve the problem reported by Marc.
[1] https://git.kernel.org/torvalds/c/4bd2c03be7
[2] https://patchwork.ozlabs.org/patch/1189139/
Fixes: 4bd2c03be707 ("net: hns: remove ndo_poll_controller")
Cc: lipeng <lipeng321@huawei.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Reported-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A malicious device may give half an answer when asked
for its MTU. The driver will proceed after this with
a garbage MTU. Anything but a complete answer must be treated
as an error.
V2: used sizeof as request by Alexander
Reported-and-tested-by: syzbot+0631d878823ce2411636@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since old firmware does not support HCLGE_OPC_PF_RST_DONE, it will
return -EOPNOTSUPP to the driver when received this command. So
for this case, it should just print a warning and return success
to the caller.
Fixes: 72e2fb07997c ("net: hns3: clear reset interrupt status in hclge_irq_handle()")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl3DQ0sACgkQSD+KveBX
+j4nKgf/XnUZGR4PHGcEfalc/p67J7jmi7SN5Xuts8uyUTgqMGni/SkWRl+S1mQy
8dl5kZK/JxBhAzzlVIcXpcmkfeXydcrm1NHMPCOMsnUrAWAEP0lE1lfLBkX1zWPi
OHb3+nziJHc0s4AI/Haca7JOj8HjBSOPpv3Udg6f53leizo31pK2FSiBASc5bRoX
EUNMD3eFAap7fjBMVLzO/JeQXxgjaqb9qU3AKopy34cg+AInZ+ZH2S++aoT7RG3J
MCPOnrSxLmhA4BUu5I81vfgFNxxPP65vI7NPIhSMY7+pOQJNPIc1p08XvIpQ9X2o
5o/rQ9tVxq2NZqcMB+b6tiHVFYu7Kw==
=OmLZ
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-11-06' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahamees says:
====================
Mellanox, mlx5 fixes 2019-11-06
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
No -stable this time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions like phy_modify_paged() read the current page, on Realtek
PHY's this means reading the value of register 0x1f. Add special
handling for reading this register, similar to what we do already
in r8168g_mdio_write(). Currently we read a random value that by
chance seems to be 0 always.
Fixes: a2928d28643e ("r8169: use paged versions of phylib MDIO access functions")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOC bit must be only set in the last descriptor. Move the logic up a
little bit to make sure it's set in the correct descriptor.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using addressing > 32 bits the TSO first descriptor only has the
header so we can't set the payload field for this descriptor. Let's
reset the variable so that buffer 2 value is zero.
Fixes: a993db88d17d ("net: stmmac: Enable support for > 32 Bits addressing in XGMAC")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, stmmac_rx() is counting the number of descriptors but it
should count the number of packets as specified by the NAPI limit.
Fix this.
Fixes: ec222003bd94 ("net: stmmac: Prepare to add Split Header support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MMC interrupts were being enabled, which is not what we want because it
will lead to a storm of interrupts that are not handled at all. Fix it
by disabling all MMC interrupts for XGMAC.
Fixes: b6cdf09f51c2 ("net: stmmac: xgmac: Implement MMC counters")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in AVB mode we need to disable flow control to prevent MAC from
pausing in TX side.
Fixes: ec6ea8e3eee9 ("net: stmmac: Add CBS support in XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect precedence of operators. For reference: AV implies AV
Feature but RAV implies only RX side AV Feature. As we want full AV
features we need to check RAV.
Fixes: c2b69474d63b ("net: stmmac: xgmac: Correct RAVSEL field interpretation")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we change between Transmission Scheduling Algorithms, we need to
clear previous values so that the new chosen algorithm is correctly
selected.
Fixes: ec6ea8e3eee9 ("net: stmmac: Add CBS support in XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split Header length is only available when L34T == 0. Fix this by
correctly checking if L34T is zero before trying to get Header length.
Fixes: 67afd6d1cfdf ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In L2 tests that filter packets by destination MAC address we need to
prevent false positives that can occur if we add an address that
collides with the existing ones.
To fix this, lets manually check if the new address to be added is
already present in the NIC and use a different one if so. For Hash
filtering this also envolves converting the address to the hash.
Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitrev32 function returns an u32 var, not an int. Fix it.
Fixes: 0efedbf11f07 ("net: stmmac: xgmac: Fix XGMAC selftests")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitrev32 function returns an u32 var, not an int. Fix it.
Fixes: 477286b53f55 ("stmmac: add GMAC4 core support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "read-modify-write register index" function is declared with a
confusing prototype: the "mask" and "reg" arguments are swapped.
Fortunately, this does not affect callers so far. Both arguments are
u32, and the wrapper macros (ocelot_rmw_ix etc) have the arguments in
the correct order (the one from ocelot_io.c).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lag_upper_info may be NULL on slave removal.
Fixes: dc96ee3730fc ("net: mscc: ocelot: add bonding support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check that the event is actually for this device should be moved
from the "port" handler to the net device handler.
Otherwise the port handler will deny bonding configuration for other
net devices in the same system (like enetc in the LS1028A) that don't
have the lag_upper_info->tx_type restriction that ocelot has.
Fixes: dc96ee3730fc ("net: mscc: ocelot: add bonding support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For vlan push action, if eswitch flow source capability is enabled, flow
source value compared with MLX5_VPORT_UPLINK enum, to determine uplink
port. This lead to syndrome in dmesg if try to add vlan push action.
For example:
$ tc filter add dev vxlan0 ingress protocol ip prio 1 flower \
enc_dst_port 4789 \
action tunnel_key unset pipe \
action vlan push id 20 pipe \
action mirred egress redirect dev ens1f0_0
$ dmesg
...
[ 2456.883693] mlx5_core 0000:82:00.0: mlx5_cmd_check:756:(pid 5273): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0xa9c090)
Use the correct enum value MLX5_FLOW_CONTEXT_FLOW_SOURCE_UPLINK.
Fixes: bb204dcf39fe ("net/mlx5e: Determine source port properly for vlan push action")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The rewrite data was no freed.
Fixes: 9db810ed2d37 ("net/mlx5: DR, Expose steering action functionality")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The value is already the calculation so remove the log prefix.
Fixes: e52c28024008 ("net/mlx5: E-Switch, Add chains and priorities")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The phy_init_hw() function may reset the PHY to a configuration
that does not match manual network settings stored in the phydev
structure. If the phy state machine is polled rather than event
driven this can create a timing hazard where the phy state machine
might alter the settings stored in the phydev structure from the
value read from the BMCR.
This commit follows invocations of phy_init_hw() by the bcmgenet
driver with invocations of the genphy_config_aneg() function to
ensure that the BMCR is written to match the settings held in the
phydev structure. This prevents the risk of manual settings being
accidentally altered.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
