IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
When the host controller dies or is removed while a device is plugged in,
the USB core will attempt to deallocate the struct usb_device. That will
call into xhci_free_dev(). This function used to attempt to submit a
disable slot command to the host controller and clean up the device
structures when that command returned. Change xhci_free_dev() to skip the
command submission and just free the memory if the host controller died.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the host controller dies (e.g. it is removed from a PCI card slot),
the xHCI driver cannot expect commands to complete. The buggy code this
patch fixes would mark an URB as canceled and then expect the URB to be
completed when the stop endpoint command completed. That would never
happen if the host controller was dead, so the USB core would just hang in
the disconnect code.
If the host controller died, and the driver asks to cancel an URB, free
any structures associated with that URB and immediately give it back.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the host controller card is removed from the system, stop the timer
function to debug the xHCI rings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current 10ms timeout is too short for some normal USBTMC device
operation, increase it to a value which was tested with previously
affected Tektronix oscilloscopes.
Signed-off-by: Gergely Imreh <imrehg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanse found a memory leak in lcd_probe. Instead of returning without
releasing the memory, jump to the error label which frees it.
http://stanse.fi.muni.cz/
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updated sierra driver version from 1.3.7 to 1.3.8 now that the autosuspend
capabilities were added to the driver.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1295) fixes a recently-added bug in the USB serial core.
If certain kinds of errors occur during probing, the core may call a
serial driver's release method without previously calling the attach
method. This causes some drivers (io_ti in particular) to perform an
invalid memory access.
The patch adds a new flag to keep track of whether or not attach has
been called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jean-Denis Girard <jd.girard@sysnux.pf>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a regression introduced in
39892da44b.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Re-structure read processing.
- Kill obsolete work queue and always push to tty in completion handler.
- Use tty_insert_flip_string instead of per character push when
possible.
- Fix stalled-read regression in 2.6.31 by using urb status to
determine when port is closed rather than port count.
- Fix race with open/close by checking ASYNCB_INITIALIZED in
unthrottle.
- Kill private rx_flag and lock and use throttle flags in
usb_serial_port instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove superfluous error checks in completion handler:
- No need to check private data and urb pointers as we check urb-status
before dereferencing priv (which is not freed until urb has been killed
on close).
- No need to check tty as it is checked again when processing.
- No need to check urb->number_of_packets on bulk urb.
Note that both private data and tty are checked again before processing
(possibly from work queue which also is cancelled on close).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove unused rx_byte counter which is never exposed as noted by Alan
Cox.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes tty_flip_buffer_push being called from hard interrupt context with
low_latency set.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following commit made console open fails while booting:
commit b50989dc44
Author: Alan Cox <alan@linux.intel.com>
Date: Sat Sep 19 13:13:22 2009 -0700
tty: make the kref destructor occur asynchronously
Due to tty release routines run in a workqueue now, error like the
following will be reported while booting:
INIT open /dev/console Input/output error
It also causes hibernation regression to appear as reported at
http://bugzilla.kernel.org/show_bug.cgi?id=14229
The reason is that now there's latency issue with closing, but when
we open a "closing not finished" tty, -EIO will be returned.
Fix it as per the following Alan's suggestion:
Fun but it's actually not a bug and the fix is wrong in itself as
the port may be closing but not yet being destructed, in which case
it seems to do the wrong thing. Opening a tty that is closing (and
could be closing for long periods) is supposed to return -EIO.
I suspect a better way to deal with this and keep the old console
timing is to split tty->shutdown into two functions.
tty->shutdown() - called synchronously just before we dump the tty
onto the waitqueue for destruction
tty->cleanup() - called when the destructor runs.
We would then do the shutdown part which can occur in IRQ context
fine, before queueing the rest of the release (from tty->magic = 0
... the end) to occur asynchronously
The USB update in -next would then need a call like
if (tty->cleanup)
tty->cleanup(tty);
at the top of the async function and the USB shutdown to be split
between shutdown and cleanup as the USB resource cleanup and final
tidy cannot occur synchronously as it needs to sleep.
In other words the logic becomes
final kref put
make object unfindable
async
clean it up
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
[ rjw: Rebased on top of 2.6.31-git, reworked the changelog. ]
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
[ Changed serial naming to match new rules, dropped tty_shutdown as per
comments from Alan Stern - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* remove asm/atomic.h inclusion from kref.h -- not needed, linux/types.h
is enough for atomic_t
* remove linux/kref.h inclusion from files which do not need it.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (24 commits)
microblaze: Disable heartbeat/enable emaclite in defconfigs
microblaze: Support simpleImage.dts make target
microblaze: Fix _start symbol to physical address
microblaze: Use LOAD_OFFSET macro to get correct LMA for all sections
microblaze: Create the LOAD_OFFSET macro used to compute VMA vs LMA offsets
microblaze: Copy ppc asm-compat.h for clean handling of constants in asm and C
microblaze: Actually show KiB rather than pages in "Freeing initrd memory:"
microblaze: Support ptrace syscall tracing.
microblaze: Updated CPU version and FPGA family codes in PVR
microblaze: Generate correct signal and siginfo for integer div-by-zero
microblaze: Don't be noisy when userspace causes hardware exceptions
microblaze: Remove ipc.h file which points to non-existing asm-generic file
microblaze: Clear sticky FSR register after generating exception signals
microblaze: Ensure CPU usermode is set on new userspace processes
microblaze: Use correct kbuild variable KBUILD_CFLAGS
microblaze: Save and restore msr in hw exception
microblaze: Add architectural support for USB EHCI host controllers
microblaze: Implement include/asm/syscall.h.
microblaze: Improve checking mechanism for MSR instruction
microblaze: Add checking mechanism for MSR instruction
...
drivers/usb/serial/sierra.c: In function 'sierra_suspend':
drivers/usb/serial/sierra.c:936: error: 'struct usb_device' has no member named 'auto_pm'
Repairs
commit e6929a9020
Author: Oliver Neukum <oliver@neukum.org>
Date: Fri Sep 4 23:19:53 2009 +0200
USB: support for autosuspend in sierra while online
Cc: Greg KH <greg@kroah.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* remove asm/atomic.h inclusion from linux/utsname.h --
not needed after kref conversion
* remove linux/utsname.h inclusion from files which do not need it
NOTE: it looks like fs/binfmt_elf.c do not need utsname.h, however
due to some personality stuff it _is_ needed -- cowardly leave ELF-related
headers and files alone.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Non blocking IO is supported in the read path of usb-skeleton.
This is done by just not blocking. As support for handling signals
without stopping IO is already there, it can be used for O_NONBLOCK, too.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb:usb-skeleton: honor O_NONBLOCK in write path
nonblocking writes are allowed by using down_trylock if necessary
to reserve an URB
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The read code path of the skeleton driver really sucks
- skel_read works only for devices which always send data
- the timeout comes out of thin air
- it blocks signals for the duration of the timeout
- it disallows nonblocking IO by design
This patch fixes it by using a real urb, a completion and interruptible waits.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a hook for updating xHCI internal structures after khubd fetches the
hub descriptor and sets up the hub's TT information. The xHCI driver must
update the internal structures before devices under the hub can be
enumerated.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For a USB hub to work under an xHCI host controller, the xHC's internal
scheduler must be made aware of the hub's characteristics. Add an xHCI
hook that the USB core will call after it fetches the hub descriptor.
This hook will add hub information to the slot context for that device,
including whether it has multiple TTs or a single TT, the number of ports
on the hub, and TT think time.
Setting up the slot context for the device is different for 0.95 and 0.96
xHCI host controllers.
Some of the slot context reserved fields in the 0.95 specification were
changed into hub fields in the 0.96 specification. Don't set the TT think
time or number of ports for a hub if we're dealing with a 0.95-compliant
xHCI host controller.
The 0.95 xHCI specification says that to modify the hub flag, we need to
issue an evaluate context command. The 0.96 specification says that flag
can be set with a configure endpoint command. Issue the correct command
based on the version reported by the hardware.
This patch does not add support for multi-TT hubs. Multi-TT hubs expose
a single TT on alt setting 0, and multi-TT on alt setting 1. The xHCI
driver can't handle setting alternate interfaces yet.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When setting up a slot context for an address device command, set the
multi-TT field if this is a low or full speed device under a HS hub with
multiple transaction translators.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xHCI driver needs to set the route string in the slot context of all
devices, not just SuperSpeed devices. The route string concept was added
in the USB 3.0 specification, section 10.1.3.2. Each hub in the topology
is expected to have no more than 15 ports in order for the route string of
a device to be unique. SuperSpeed hubs are restricted to only having 15
ports, but FS/LS/HS hubs are not. The xHCI specification says that if the
port number the device is under is greater than 15, that portion of the
route string shall be set to 15.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the xHCI driver, configure endpoint commands that are submitted to the
hardware may involve one of two data structures. If the configure
endpoint command is setting up a new configuration or modifying max packet
sizes, the data structures and completions are statically allocated in the
xhci_virt_device structure. If the command is being used to set up
streams or add hub information, then the data structures are dynamically
allocated, and placed on a device command waiting list.
Break out the code to check whether a completed command is in the device
command waiting list. Fix a subtle bug in the old code: continue
processing the command if the command isn't in the wait list. In the old
code, if there was a command in the wait list, but it didn't match the
completed command, the completed command event would be dropped.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some commands to the xHCI hardware cannot be allowed to fail due to out of
memory issues or the command ring being full.
Add a way to reserve a TRB on the command ring, and make all command
queueing functions indicate whether they are using a reserved TRB.
Add a way to pre-allocate all the memory a command might need. A command
needs an input context, a variable to store the status, and (optionally) a
completion for the caller to wait on. Change all code that assumes the
input device context, status, and completion for a command is stored in
the xhci virtual USB device structure (xhci_virt_device).
Store pending completions in a FIFO in xhci_virt_device. Make the event
handler for a configure endpoint command check to see whether a pending
command in the list has completed. We need to use separate input device
contexts for some configure endpoint commands, since multiple drivers can
submit requests at the same time that require a configure endpoint
command.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor common code to set up the add and drop flags for the input device
context setup. This setup is used before a configure endpoint command for
the reset endpoint quirk, and will be used for the command to alloc or
free streams rings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xhci_ring structure contained information that is really related to an
endpoint, not a ring. This will cause problems later when endpoint
streams are supported and there are multiple rings per endpoint.
Move the endpoint state and cancellation information into a new virtual
endpoint structure, xhci_virt_ep. The list of TRBs to be cancelled should
be per endpoint, not per ring, for easy access. There can be only one TRB
that the endpoint stopped on after a stop endpoint command (even with
streams enabled); move the stopped TRB information into the new virtual
endpoint structure. Also move the 31 endpoint rings and temporary ring
storage from the virtual device structure (xhci_virt_device) into the
virtual endpoint structure (xhci_virt_ep).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order:
Add reference to relevant section of USBTMC usb488 subclass specs.
Print debug output of capabilities only when it was retrieved successfully.
Clear return value on success, otherwise driver always reports failure.
Signed-off-by: Gergely Imreh <imrehg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: check for IO errors usb_set_interface can return
if they happen while unbinding a flag is set to retry upon probe
if they happen during probe they are handled as probe errors
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1283) adds a new flag, USBDEVFS_URB_BULK_CONTINUATION,
to usbfs. It is intended for userspace libraries such as libusb and
openusb. When they have to break up a single usbfs bulk transfer into
multiple URBs, they will set the flag on all but the first URB of the
series.
If an error other than an unlink occurs, the kernel will automatically
cancel all the following URBs for the same endpoint and refuse to
accept new submissions, until an URB is encountered that is not marked
as a BULK_CONTINUATION. Such an URB would indicate the start of a new
transfer or the presence of an older library, so the kernel returns to
normal operation.
This enables libraries to delimit bulk transfers correctly, even in
the presence of early termination as indicated by short packets.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This implements support for autosuspend in the sierra driver while online.
Remote wakeup is used for reception. Transmission is facilitated with a queue
and the asynchronous autopm mechanism. To prevent races a private flag
for opened ports and a counter of running transmissions needs to be added.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Tested-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order for the dbgp driver to survive suspend/resume, on every ehci
resume operation the debug controller must get re-initialized.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: dbrownell@users.sourceforge.net
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some EHCI debug controllers after the host controller driver is
activated, the debug controller will occasionally fail to submit a
bulk write URB. On controllers that exhibit this behavior a dummy
bulk write must get submitted to resynchronize the device.
The "dummy bulk write" does not get received by the host attached to
the other end of the usb debug device. The usb debug device simply
acknowledges the "dummy bulk write" and returns to a usable state.
The behavior, without this patch is that you see missing text from a
complete kernel boot when using the keep option to the earlyprintk
kernel argument.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some EHCI usb debug controllers, the EHCI debug device will fail to
be seen after a port reset, after a warm reset. Two options exist to
get the device to initialize correctly.
Option 1 is to unplug and plug in the device.
Option 2 is to use the EHCI port test to get the usb debug device to
start talking again. At that point the debug controller port reset
will succeed.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
CC: dbrownell@users.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the EHCI debug port is initialized and in use, the EHCI host
controller driver must follow two rules.
1) If the EHCI host driver issues a controller reset, the debug
controller driver re-initialization must get called after the reset
is completed.
2) The EHCI host driver should ignore any requests to the physical
EHCI debug port when the EHCI debug port is in use.
The code to check for the debug port was moved from ehci_pci_reinit()
to ehci_pci_setup because it must get called prior to ehci_reset()
which will clear the debug port registers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: dbrownell@users.sourceforge.net
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements several changes:
1) Improve the capability to debug the dbgp driver
The dbgp_ehci_status() was added in a number of places to report
the critical ehci registers to diagnose the cause of a failure of
the ehci-dbgp driver.
2) Capability to survive the host controller initialization
The dbgp_external_startup(), dbgp_not_safe, and dbgp_phys_port were
added so as to allow the ehci-dbgp to re-initialize after the ehci
host controller is reset by the standard host controller driver.
This same routine is common for the early startup or
re-initialization.
This resulted in the need to move some of the initialization code
out of the __init section because the ehci driver has the
possibility to be loaded later on as a kernel module.
3) Stability improvements for device initialization
The device enumeration from 0 to 127 has the possibility to fail
the first time after a warm reset on some older EHCI debug
controllers. The enumeration will be tried up to 3 times to
account for this failure case.
The dbg_wait_until_complete() was changed to wait up to 250 ms
before failing which only comes into play during device
initialization. The maximum delay will never get hit during the
course of normal operation of the driver, unless the device got
unplugged or there was a ehci controller failure, in which case the
dbgp device driver will shut itself down.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: dbrownell@users.sourceforge.net
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When using the EHCI host controller as a polled device, a bit more
tolerance is required in terms of delays. On some 3+ghz systems the
cpu loops were faster than the EHCI device mmio and resulted in the
controller failing to initialize.
On at least one first generation EHCI controller when it was not
operating in interrupt mode, it would fail to report a port change
status, but executing the port reset allowed the debug controller to
work correctly anyway. This errata causes a one time 300ms delay in
the boot time, where as the typical delay is 1-5ms for an EHCI
controller that does not have this errata.
The debug printk's were fixed to have the correct state messages, and
there was a conversion from using early_printk to printk to avoid
calling the dbgp driver while debugging the initialization.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI quirk code executes a BIOS hand off to obtain full control of
the EHCI host controller, the self contained ehci-dbgp driver must do
the same thing using the early PCI API, else the BIOS can cause a
fatal fault.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: dbrownell@users.sourceforge.net
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The rs232 drivers send a carriage return prior to a new line in the
early printk code.
The usb debug driver should do the same because you want to be able to
use the same terminal programs and tools for analysis of early printk
data.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the dbgp early printk driver in advance of refactoring and adding
new code, so the changes to this code are tracked separately from the
move of the code.
The drivers/usb/early directory will be the location of the current
and future early usb code for driving usb devices prior initializing
the standard interrupt driven USB drivers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
