IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The IPI shorthand functionality delivers IPI/NMI broadcasts to all CPUs in
the system. This can have similar side effects as the MCE broadcasting when
CPUs are waiting in the BIOS or are offlined.
The kernel tracks already the state of offlined CPUs whether they have been
brought up at least once so that the CR4 MCE bit is set to make sure that
MCE broadcasts can't brick the machine.
Utilize that information and compare it to the cpu_present_mask. If all
present CPUs have been brought up at least once then the broadcast side
effect is mitigated by disabling regular interrupt/IPI delivery in the APIC
itself and by the cpu offline check at the begin of the NMI handler.
Use a static key to switch between broadcasting via shorthands or sending
the IPI/NMI one by one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190722105220.386410643@linutronix.de
For the upcoming shorthand support for all APIC incarnations the command
line option needs to be available for 64 bit as well.
While at it, rename the control variable, make it static and mark it
__ro_after_init.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190722105220.278327940@linutronix.de
To support NMI shorthand broadcasts add the safe wait for ICR idle for NMI
vector delivery.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190722105220.185838026@linutronix.de
The SDM states:
"The destination shorthand field of the ICR allows the delivery mode to be
by-passed in favor of broadcasting the IPI to all the processors on the
system bus and/or back to itself (see Section 10.6.1, Interrupt Command
Register (ICR)). Three destination shorthands are supported: self, all
excluding self, and all including self. The destination mode is ignored
when a destination shorthand is used."
So there is no point to supply the destination mode to the shorthand
delivery function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190722105220.094613426@linutronix.de
In order to support IPI/NMI broadcasting via the shorthand mechanism side
effects of shorthands need to be mitigated:
Shorthand IPIs and NMIs hit all CPUs including unplugged CPUs
Neither of those can be handled on unplugged CPUs for obvious reasons.
It would be trivial to just fully disable the APIC via the enable bit in
MSR_APICBASE. But that's not possible because clearing that bit on systems
based on the 3 wire APIC bus would require a hardware reset to bring it
back as the APIC would lose track of bus arbitration. On systems with FSB
delivery APICBASE could be disabled, but it has to be guaranteed that no
interrupt is sent to the APIC while in that state and it's not clear from
the SDM whether it still responds to INIT/SIPI messages.
Therefore stay on the safe side and switch the APIC into soft disabled mode
so it won't deliver any regular vector to the CPU.
NMIs are still propagated to the 'dead' CPUs. To mitigate that add a check
for the CPU being offline on early nmi entry and if so bail.
Note, this cannot use the stop/restart_nmi() magic which is used in the
alternatives code. A dead CPU cannot invoke nmi_enter() or anything else
due to RCU and other reasons.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907241723290.1791@nanos.tec.linutronix.de
arch_smt_update() will be used to control IPI/NMI broadcasting via the
shorthand mechanism. Keeping it in the bugs file and calling the apic
function from there is possible, but not really intuitive.
Move it to a neutral place and invoke the bugs function from there.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190722105219.910317273@linutronix.de
Now there are three small local headers. Some contain functions which are
only used in one source file.
Move all the inlines and declarations into a single local header and the
inlines which are only used in one source file into that.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190722105219.618612624@linutronix.de
All of these APIC files include the world and some more. Remove the
unneeded cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190722105219.342631201@linutronix.de
In course of developing shorthand based IPI support issues with the
function which tries to clear eventually pending ISR bits in the local APIC
were observed.
1) O-day testing triggered the WARN_ON() in apic_pending_intr_clear().
This warning is emitted when the function fails to clear pending ISR
bits or observes pending IRR bits which are not delivered to the CPU
after the stale ISR bit(s) are ACK'ed.
Unfortunately the function only emits a WARN_ON() and fails to dump
the IRR/ISR content. That's useless for debugging.
Feng added spot on debug printk's which revealed that the stale IRR
bit belonged to the APIC timer interrupt vector, but adding ad hoc
debug code does not help with sporadic failures in the field.
Rework the loop so the full IRR/ISR contents are saved and on failure
dumped.
2) The loop termination logic is interesting at best.
If the machine has no TSC or cpu_khz is not known yet it tries 1
million times to ack stale IRR/ISR bits. What?
With TSC it uses the TSC to calculate the loop termination. It takes a
timestamp at entry and terminates the loop when:
(rdtsc() - start_timestamp) >= (cpu_hkz << 10)
That's roughly one second.
Both methods are problematic. The APIC has 256 vectors, which means
that in theory max. 256 IRR/ISR bits can be set. In practice this is
impossible and the chance that more than a few bits are set is close
to zero.
With the pure loop based approach the 1 million retries are complete
overkill.
With TSC this can terminate too early in a guest which is running on a
heavily loaded host even with only a couple of IRR/ISR bits set. The
reason is that after acknowledging the highest priority ISR bit,
pending IRRs must get serviced first before the next round of
acknowledge can take place as the APIC (real and virtualized) does not
honour EOI without a preceeding interrupt on the CPU. And every APIC
read/write takes a VMEXIT if the APIC is virtualized. While trying to
reproduce the issue 0-day reported it was observed that the guest was
scheduled out long enough under heavy load that it terminated after 8
iterations.
Make the loop terminate after 512 iterations. That's plenty enough
in any case and does not take endless time to complete.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190722105219.158847694@linutronix.de
If the APIC was already enabled on entry of setup_local_APIC() then
disabling it soft via the SPIV register makes a lot of sense.
That masks all LVT entries and brings it into a well defined state.
Otherwise previously enabled LVTs which are not touched in the setup
function stay unmasked and might surprise the just booting kernel.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190722105219.068290579@linutronix.de
If the APIC is soft disabled then unmasking an LVT entry does not work and
the write is ignored. perf_events_lapic_init() tries to do so.
Move the invocation after the point where the APIC has been enabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190722105218.962517234@linutronix.de
apic->send_IPI_allbutself() takes a vector number as argument.
APIC_DM_NMI is clearly not a vector number. It's defined to 0x400 which is
outside the vector space.
Use NMI_VECTOR instead as that's what it is intended to be.
Fixes: 82da3ff89dc2 ("x86: kgdb support")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190722105218.855189979@linutronix.de
A reboot request sends an IPI via the reboot vector and waits for all other
CPUs to stop. If one or more CPUs are in critical regions with interrupts
disabled then the IPI is not handled on those CPUs and the shutdown hangs
if native_stop_other_cpus() is called with the wait argument set.
Such a situation can happen when one CPU was stopped within a lock held
section and another CPU is trying to acquire that lock with interrupts
disabled. There are other scenarios which can cause such a lockup as well.
In theory the shutdown should be attempted by an NMI IPI after the timeout
period elapsed. Though the wait loop after sending the reboot vector IPI
prevents this. It checks the wait request argument and the timeout. If wait
is set, which is true for sys_reboot() then it won't fall through to the
NMI shutdown method after the timeout period has finished.
This was an oversight when the NMI shutdown mechanism was added to handle
the 'reboot IPI is not working' situation. The mechanism was added to deal
with stuck panic shutdowns, which do not have the wait request set, so the
'wait request' case was probably not considered.
Remove the wait check from the post reboot vector IPI wait loop and enforce
that the wait loop in the NMI fallback path is invoked even if NMI IPIs are
disabled or the registration of the NMI handler fails. That second wait
loop will then hang if not all CPUs shutdown and the wait argument is set.
[ tglx: Avoid the hard to parse line break in the NMI fallback path,
add comments and massage the changelog ]
Fixes: 7d007d21e539 ("x86/reboot: Use NMI to assist in shutting down if IRQ fails")
Signed-off-by: Grzegorz Halat <ghalat@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Don Zickus <dzickus@redhat.com>
Link: https://lkml.kernel.org/r/20190628122813.15500-1-ghalat@redhat.com
X86_HYPER_NATIVE isn't accurate for checking if running on native platform,
e.g. CONFIG_HYPERVISOR_GUEST isn't set or "nopv" is enabled.
Checking the CPU feature bit X86_FEATURE_HYPERVISOR to determine if it's
running on native platform is more accurate.
This still doesn't cover the platforms on which X86_FEATURE_HYPERVISOR is
unsupported, e.g. VMware, but there is nothing which can be done about this
scenario.
Fixes: 8a4b06d391b0 ("x86/speculation/mds: Add sysfs reporting for MDS")
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1564022349-17338-1-git-send-email-zhenzhong.duan@oracle.com
Rui reported that on a Pentium D machine which has HPET forced enabled
because it is not advertised by ACPI, the early counter is counting check
leads to a silent boot hang.
The reason is that the ordering of checking the counter first and then
reconfiguring the HPET fails to work on that machine. As the HPET is not
advertised and presumably not initialized by the BIOS the early enable and
the following reconfiguration seems to bring it into a broken state. Adding
clocksource=jiffies to the command line results in the following
clocksource watchdog warning:
clocksource: timekeeping watchdog on CPU1:
Marking clocksource 'tsc-early' as unstable because the skew is too large:
clocksource: 'hpet' wd_now: 33 wd_last: 33 mask: ffffffff
That clearly shows that the HPET is not counting after it got reconfigured
and reenabled. If the counter is not working then the HPET timer is not
expiring either, which explains the boot hang.
Move the counter is counting check after the full configuration again to
unbreak these systems.
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fixes: 3222daf970f3 ("x86/hpet: Separate counter check out of clocksource register code")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907250810530.1791@nanos.tec.linutronix.de
The ret comparison and return are unnecessary as of commit f296f2634920
("x86/kexec: Remove walk_iomem_res() call with GART type")
elf_header_exclude_ranges() returns ret in any case, with or without this
comparison.
[ tglx: Use a proper commit reference instead of full SHA ]
Signed-off-by: Nikolas Nyby <nikolas@gnu.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190724041337.8346-1-nikolas@gnu.org
AMD and Intel both have serializing lfence (X86_FEATURE_LFENCE_RDTSC).
They've both had it for a long time, and AMD has had it enabled in Linux
since Spectre v1 was announced.
Back then, there was a proposal to remove the serializing mfence feature
bit (X86_FEATURE_MFENCE_RDTSC), since both AMD and Intel have
serializing lfence. At the time, it was (ahem) speculated that some
hypervisors might not yet support its removal, so it remained for the
time being.
Now a year-and-a-half later, it should be safe to remove.
I asked Andrew Cooper about whether it's still needed:
So if you're virtualised, you've got no choice in the matter. lfence
is either dispatch-serialising or not on AMD, and you won't be able to
change it.
Furthermore, you can't accurately tell what state the bit is in, because
the MSR might not be virtualised at all, or may not reflect the true
state in hardware. Worse still, attempting to set the bit may not be
successful even if there isn't a fault for doing so.
Xen sets the DE_CFG bit unconditionally, as does Linux by the looks of
things (see MSR_F10H_DECFG_LFENCE_SERIALIZE_BIT). ISTR other hypervisor
vendors saying the same, but I don't have any information to hand.
If you are running under a hypervisor which has been updated, then
lfence will almost certainly be dispatch-serialising in practice, and
you'll almost certainly see the bit already set in DE_CFG. If you're
running under a hypervisor which hasn't been patched since Spectre,
you've already lost in many more ways.
I'd argue that X86_FEATURE_MFENCE_RDTSC is not worth keeping.
So remove it. This will reduce some code rot, and also make it easier
to hook barrier_nospec() up to a cmdline disable for performance
raisins, without having to need an alternative_3() macro.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/d990aa51e40063acb9888e8c1b688e41355a9588.1562255067.git.jpoimboe@redhat.com
There is no reader of trampoline_status, it's only written.
It turns out that after commit ce4b1b16502b ("x86/smpboot: Initialize
secondary CPU only if master CPU will wait for it"), trampoline_status is
not needed any more.
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1563266424-3472-1-git-send-email-kernelfans@gmail.com
Commit e6401c130931 ("x86/irq/64: Split the IRQ stack into its own pages")
missed to update one piece of comment as it did to its peer in Xen, which
will confuse people who still need to read comment.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190719081635.26528-1-caoj.fnst@cn.fujitsu.com
Some Lenovo 2-in-1s with a detachable keyboard have a portrait screen but
advertise a landscape resolution and pitch, resulting in a messed up
display if the kernel tries to show anything on the efifb (because of the
wrong pitch).
Fix this by adding a new DMI match table for devices which need to have
their width and height swapped.
At first it was tried to use the existing table for overriding some of the
efifb parameters, but some of the affected devices have variants with
different LCD resolutions which will not work with hardcoded override
values.
Reference: https://bugzilla.redhat.com/show_bug.cgi?id=1730783
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190721152418.11644-1-hdegoede@redhat.com
When arch_stack_walk_user() is called from atomic contexts, access_ok() can
trigger the following warning if compiled with CONFIG_DEBUG_ATOMIC_SLEEP=y.
Reproducer:
// CONFIG_DEBUG_ATOMIC_SLEEP=y
# cd /sys/kernel/debug/tracing
# echo 1 > options/userstacktrace
# echo 1 > events/irq/irq_handler_entry/enable
WARNING: CPU: 0 PID: 2649 at arch/x86/kernel/stacktrace.c:103 arch_stack_walk_user+0x6e/0xf6
CPU: 0 PID: 2649 Comm: bash Not tainted 5.3.0-rc1+ #99
RIP: 0010:arch_stack_walk_user+0x6e/0xf6
Call Trace:
<IRQ>
stack_trace_save_user+0x10a/0x16d
trace_buffer_unlock_commit_regs+0x185/0x240
trace_event_buffer_commit+0xec/0x330
trace_event_raw_event_irq_handler_entry+0x159/0x1e0
__handle_irq_event_percpu+0x22d/0x440
handle_irq_event_percpu+0x70/0x100
handle_irq_event+0x5a/0x8b
handle_edge_irq+0x12f/0x3f0
handle_irq+0x34/0x40
do_IRQ+0xa6/0x1f0
common_interrupt+0xf/0xf
</IRQ>
Fix it by calling __range_not_ok() directly instead of access_ok() as
copy_from_user_nmi() does. This is fine here because the actual copy is
inside a pagefault disabled region.
Reported-by: Juri Lelli <juri.lelli@gmail.com>
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190722083216.16192-2-devel@etsukata.com
Add a new AVX512 instruction group/feature for enumeration in
/proc/cpuinfo: AVX512_VP2INTERSECT.
CPUID.(EAX=7,ECX=0):EDX[bit 8] AVX512_VP2INTERSECT
Detailed information of CPUID bits for this feature can be found in
the Intel Architecture Intsruction Set Extensions Programming Reference
document (refer to Table 1-2). A copy of this document is available at
https://bugzilla.kernel.org/show_bug.cgi?id=204215.
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190717234632.32673-3-gayatri.kammela@intel.com
Improve code readability by adding a tab between the elements of each
structure in an array of cpuid-dep struct so longer feature names will fit.
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190717234632.32673-2-gayatri.kammela@intel.com
For unfortunate historical reasons, the x32 syscalls and the x86_64
syscalls are not all numbered the same. As an example, ioctl() is nr 16 on
x86_64 but 514 on x32.
This has potentially nasty consequences, since it means that there are two
valid RAX values to do ioctl(2) and two invalid RAX values. The valid
values are 16 (i.e. ioctl(2) using the x86_64 ABI) and (514 | 0x40000000)
(i.e. ioctl(2) using the x32 ABI).
The invalid values are 514 and (16 | 0x40000000). 514 will enter the
"COMPAT_SYSCALL_DEFINE3(ioctl, ...)" entry point with in_compat_syscall()
and in_x32_syscall() returning false, whereas (16 | 0x40000000) will enter
the native entry point with in_compat_syscall() and in_x32_syscall()
returning true. Both are bogus, and both will exercise code paths in the
kernel and in any running seccomp filters that really ought to be
unreachable.
Splitting out the x32 syscalls into their own tables, allows both bogus
invocations to return -ENOSYS. I've checked glibc, musl, and Bionic, and
all of them appear to call syscalls with their correct numbers, so this
change should have no effect on them.
There is an added benefit going forward: new syscalls that need special
handling on x32 can share the same number on x32 and x86_64. This means
that the special syscall range 512-547 can be treated as a legacy wart
instead of something that may need to be extended in the future.
Also add a selftest to verify the new behavior.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/208024256b764312598f014ebfb0a42472c19354.1562185330.git.luto@kernel.org
There is a lot of infrastructure for functionality which is used
exclusively in __{save,restore}_processor_state() on the suspend/resume
path.
cr8 is an alias of APIC_TASKPRI, and APIC_TASKPRI is saved/restored by
lapic_{suspend,resume}(). Saving and restoring cr8 independently of the
rest of the Local APIC state isn't a clever thing to be doing.
Delete the suspend/resume cr8 handling, which shrinks the size of struct
saved_context, and allows for the removal of both PVOPS.
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lkml.kernel.org/r/20190715151641.29210-1-andrew.cooper3@citrix.com
The APIC, per spec, is fundamentally confused and thinks that interrupt
vectors 16-31 are valid. This makes no sense -- the CPU reserves vectors
0-31 for exceptions (faults, traps, etc). Obviously, no device should
actually produce an interrupt with vector 16-31, but robustness can be
improved by setting the APIC TPR class to 1, which will prevent delivery of
an interrupt with a vector below 32.
Note: This is *not* intended as a security measure against attackers who
control malicious hardware. Any PCI or similar hardware that can be
controlled by an attacker MUST be behind a functional IOMMU that remaps
interrupts. The purpose of this change is to reduce the chance that a
certain class of device malfunctions crashes the kernel in hard-to-debug
ways.
Suggested-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/dc04a9f8b234d7b0956a8d2560b8945bcd9c4bf7.1563117760.git.luto@kernel.org
Pull x86 fixes from Thomas Gleixner:
"A set of x86 specific fixes and updates:
- The CR2 corruption fixes which store CR2 early in the entry code
and hand the stored address to the fault handlers.
- Revert a forgotten leftover of the dropped FSGSBASE series.
- Plug a memory leak in the boot code.
- Make the Hyper-V assist functionality robust by zeroing the shadow
page.
- Remove a useless check for dead processes with LDT
- Update paravirt and VMware maintainers entries.
- A few cleanup patches addressing various compiler warnings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry/64: Prevent clobbering of saved CR2 value
x86/hyper-v: Zero out the VP ASSIST PAGE on allocation
x86, boot: Remove multiple copy of static function sanitize_boot_params()
x86/boot/compressed/64: Remove unused variable
x86/boot/efi: Remove unused variables
x86/mm, tracing: Fix CR2 corruption
x86/entry/64: Update comments and sanity tests for create_gap
x86/entry/64: Simplify idtentry a little
x86/entry/32: Simplify common_exception
x86/paravirt: Make read_cr2() CALLEE_SAVE
MAINTAINERS: Update PARAVIRT_OPS_INTERFACE and VMWARE_HYPERVISOR_INTERFACE
x86/process: Delete useless check for dead process with LDT
x86: math-emu: Hide clang warnings for 16-bit overflow
x86/e820: Use proper booleans instead of 0/1
x86/apic: Silence -Wtype-limits compiler warnings
x86/mm: Free sme_early_buffer after init
x86/boot: Fix memory leak in default_get_smp_config()
Revert "x86/ptrace: Prevent ptrace from clearing the FS/GS selector" and fix the test
Pull core fixes from Thomas Gleixner:
- A collection of objtool fixes which address recent fallout partially
exposed by newer toolchains, clang, BPF and general code changes.
- Force USER_DS for user stack traces
[ Note: the "objtool fixes" are not all to objtool itself, but for
kernel code that triggers objtool warnings.
Things like missing function size annotations, or code that confuses
the unwinder etc. - Linus]
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
objtool: Support conditional retpolines
objtool: Convert insn type to enum
objtool: Fix seg fault on bad switch table entry
objtool: Support repeated uses of the same C jump table
objtool: Refactor jump table code
objtool: Refactor sibling call detection logic
objtool: Do frame pointer check before dead end check
objtool: Change dead_end_function() to return boolean
objtool: Warn on zero-length functions
objtool: Refactor function alias logic
objtool: Track original function across branches
objtool: Add mcsafe_handle_tail() to the uaccess safe list
bpf: Disable GCC -fgcse optimization for ___bpf_prog_run()
x86/uaccess: Remove redundant CLACs in getuser/putuser error paths
x86/uaccess: Don't leak AC flag into fentry from mcsafe_handle_tail()
x86/uaccess: Remove ELF function annotation from copy_user_handle_tail()
x86/head/64: Annotate start_cpu0() as non-callable
x86/entry: Fix thunk function ELF sizes
x86/kvm: Don't call kvm_spurious_fault() from .fixup
x86/kvm: Replace vmx_vmenter()'s call to kvm_spurious_fault() with UD2
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCXTFdBAAKCRCAXGG7T9hj
vkwEAQDKDApCcJymAaq+BP2/lU/kErzFFXQ7seDN84q13ZMfcwEAzDz7vU1zicMP
Sdq1LzFdiuXjk34BBi2PURXZAVoaXgU=
=KkHz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.3a-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"Fixes and features:
- A series to introduce a common command line parameter for disabling
paravirtual extensions when running as a guest in virtualized
environment
- A fix for int3 handling in Xen pv guests
- Removal of the Xen-specific tmem driver as support of tmem in Xen
has been dropped (and it was experimental only)
- A security fix for running as Xen dom0 (XSA-300)
- A fix for IRQ handling when offlining cpus in Xen guests
- Some small cleanups"
* tag 'for-linus-5.3a-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: let alloc_xenballooned_pages() fail if not enough memory free
xen/pv: Fix a boot up hang revealed by int3 self test
x86/xen: Add "nopv" support for HVM guest
x86/paravirt: Remove const mark from x86_hyper_xen_hvm variable
xen: Map "xen_nopv" parameter to "nopv" and mark it obsolete
x86: Add "nopv" parameter to disable PV extensions
x86/xen: Mark xen_hvm_need_lapic() and xen_x2apic_para_available() as __init
xen: remove tmem driver
Revert "x86/paravirt: Set up the virt_spin_lock_key after static keys get initialized"
xen/events: fix binding user event channels to cpus
Pull vfs mount updates from Al Viro:
"The first part of mount updates.
Convert filesystems to use the new mount API"
* 'work.mount0' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
mnt_init(): call shmem_init() unconditionally
constify ksys_mount() string arguments
don't bother with registering rootfs
init_rootfs(): don't bother with init_ramfs_fs()
vfs: Convert smackfs to use the new mount API
vfs: Convert selinuxfs to use the new mount API
vfs: Convert securityfs to use the new mount API
vfs: Convert apparmorfs to use the new mount API
vfs: Convert openpromfs to use the new mount API
vfs: Convert xenfs to use the new mount API
vfs: Convert gadgetfs to use the new mount API
vfs: Convert oprofilefs to use the new mount API
vfs: Convert ibmasmfs to use the new mount API
vfs: Convert qib_fs/ipathfs to use the new mount API
vfs: Convert efivarfs to use the new mount API
vfs: Convert configfs to use the new mount API
vfs: Convert binfmt_misc to use the new mount API
convenience helper: get_tree_single()
convenience helper get_tree_nodev()
vfs: Kill sget_userns()
...
Merge yet more updates from Andrew Morton:
"The rest of MM and a kernel-wide procfs cleanup.
Summary of the more significant patches:
- Patch series "mm/memory_hotplug: Factor out memory block
devicehandling", v3. David Hildenbrand.
Some spring-cleaning of the memory hotplug code, notably in
drivers/base/memory.c
- "mm: thp: fix false negative of shmem vma's THP eligibility". Yang
Shi.
Fix /proc/pid/smaps output for THP pages used in shmem.
- "resource: fix locking in find_next_iomem_res()" + 1. Nadav Amit.
Bugfix and speedup for kernel/resource.c
- Patch series "mm: Further memory block device cleanups", David
Hildenbrand.
More spring-cleaning of the memory hotplug code.
- Patch series "mm: Sub-section memory hotplug support". Dan
Williams.
Generalise the memory hotplug code so that pmem can use it more
completely. Then remove the hacks from the libnvdimm code which
were there to work around the memory-hotplug code's constraints.
- "proc/sysctl: add shared variables for range check", Matteo Croce.
We have about 250 instances of
int zero;
...
.extra1 = &zero,
in the tree. This is a tree-wide sweep to make all those private
"zero"s and "one"s use global variables.
Alas, it isn't practical to make those two global integers const"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (38 commits)
proc/sysctl: add shared variables for range check
mm: migrate: remove unused mode argument
mm/sparsemem: cleanup 'section number' data types
libnvdimm/pfn: stop padding pmem namespaces to section alignment
libnvdimm/pfn: fix fsdax-mode namespace info-block zero-fields
mm/devm_memremap_pages: enable sub-section remap
mm: document ZONE_DEVICE memory-model implications
mm/sparsemem: support sub-section hotplug
mm/sparsemem: prepare for sub-section ranges
mm: kill is_dev_zone() helper
mm/hotplug: kill is_dev_zone() usage in __remove_pages()
mm/sparsemem: convert kmalloc_section_memmap() to populate_section_memmap()
mm/hotplug: prepare shrink_{zone, pgdat}_span for sub-section removal
mm/sparsemem: add helpers track active portions of a section at boot
mm/sparsemem: introduce a SECTION_IS_EARLY flag
mm/sparsemem: introduce struct mem_section_usage
drivers/base/memory.c: get rid of find_memory_block_hinted()
mm/memory_hotplug: move and simplify walk_memory_blocks()
mm/memory_hotplug: rename walk_memory_range() and pass start+size instead of pfns
mm: make register_mem_sect_under_node() static
...
In the sysctl code the proc_dointvec_minmax() function is often used to
validate the user supplied value between an allowed range. This
function uses the extra1 and extra2 members from struct ctl_table as
minimum and maximum allowed value.
On sysctl handler declaration, in every source file there are some
readonly variables containing just an integer which address is assigned
to the extra1 and extra2 members, so the sysctl range is enforced.
The special values 0, 1 and INT_MAX are very often used as range
boundary, leading duplication of variables like zero=0, one=1,
int_max=INT_MAX in different source files:
$ git grep -E '\.extra[12].*&(zero|one|int_max)' |wc -l
248
Add a const int array containing the most commonly used values, some
macros to refer more easily to the correct array member, and use them
instead of creating a local one for every object file.
This is the bloat-o-meter output comparing the old and new binary
compiled with the default Fedora config:
# scripts/bloat-o-meter -d vmlinux.o.old vmlinux.o
add/remove: 2/2 grow/shrink: 0/2 up/down: 24/-188 (-164)
Data old new delta
sysctl_vals - 12 +12
__kstrtab_sysctl_vals - 12 +12
max 14 10 -4
int_max 16 - -16
one 68 - -68
zero 128 28 -100
Total: Before=20583249, After=20583085, chg -0.00%
[mcroce@redhat.com: tipc: remove two unused variables]
Link: http://lkml.kernel.org/r/20190530091952.4108-1-mcroce@redhat.com
[akpm@linux-foundation.org: fix net/ipv6/sysctl_net_ipv6.c]
[arnd@arndb.de: proc/sysctl: make firmware loader table conditional]
Link: http://lkml.kernel.org/r/20190617130014.1713870-1-arnd@arndb.de
[akpm@linux-foundation.org: fix fs/eventpoll.c]
Link: http://lkml.kernel.org/r/20190430180111.10688-1-mcroce@redhat.com
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After an objtool improvement, it complains about the fact that
start_cpu0() jumps to code which has an LRET instruction.
arch/x86/kernel/head_64.o: warning: objtool: .head.text+0xe4: unsupported instruction in callable function
Technically, start_cpu0() is callable, but it acts nothing like a
callable function. Prevent objtool from treating it like one by
removing its ELF function annotation.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/6b1b4505fcb90571a55fa1b52d71fb458ca24454.1563413318.git.jpoimboe@redhat.com
The __raw_callee_save_*() functions have an ELF symbol size of zero,
which confuses objtool and other tools.
Fixes a bunch of warnings like the following:
arch/x86/xen/mmu_pv.o: warning: objtool: __raw_callee_save_xen_pte_val() is missing an ELF size annotation
arch/x86/xen/mmu_pv.o: warning: objtool: __raw_callee_save_xen_pgd_val() is missing an ELF size annotation
arch/x86/xen/mmu_pv.o: warning: objtool: __raw_callee_save_xen_make_pte() is missing an ELF size annotation
arch/x86/xen/mmu_pv.o: warning: objtool: __raw_callee_save_xen_make_pgd() is missing an ELF size annotation
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/afa6d49bb07497ca62e4fc3b27a2d0cece545b4e.1563413318.git.jpoimboe@redhat.com
- Add user space specific memory reading for kprobes
- Allow kprobes to be executed earlier in boot
The rest are mostly just various clean ups and small fixes.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXS88txQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qhaPAQDHaAmu6wXtZjZE6GU4ZP61UNgDECmZ
4wlGrNc1AAlqAQD/QC8339p37aDCp9n27VY1wmJwF3nca+jAHfQLqWkkYgw=
=n/tz
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"The main changes in this release include:
- Add user space specific memory reading for kprobes
- Allow kprobes to be executed earlier in boot
The rest are mostly just various clean ups and small fixes"
* tag 'trace-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (33 commits)
tracing: Make trace_get_fields() global
tracing: Let filter_assign_type() detect FILTER_PTR_STRING
tracing: Pass type into tracing_generic_entry_update()
ftrace/selftest: Test if set_event/ftrace_pid exists before writing
ftrace/selftests: Return the skip code when tracing directory not configured in kernel
tracing/kprobe: Check registered state using kprobe
tracing/probe: Add trace_event_call accesses APIs
tracing/probe: Add probe event name and group name accesses APIs
tracing/probe: Add trace flag access APIs for trace_probe
tracing/probe: Add trace_event_file access APIs for trace_probe
tracing/probe: Add trace_event_call register API for trace_probe
tracing/probe: Add trace_probe init and free functions
tracing/uprobe: Set print format when parsing command
tracing/kprobe: Set print format right after parsed command
kprobes: Fix to init kprobes in subsys_initcall
tracepoint: Use struct_size() in kmalloc()
ring-buffer: Remove HAVE_64BIT_ALIGNED_ACCESS
ftrace: Enable trampoline when rec count returns back to one
tracing/kprobe: Do not run kprobe boot tests if kprobe_event is on cmdline
tracing: Make a separate config for trace event self tests
...
Despite the current efforts to read CR2 before tracing happens there still
exist a number of possible holes:
idtentry page_fault do_page_fault has_error_code=1
call error_entry
TRACE_IRQS_OFF
call trace_hardirqs_off*
#PF // modifies CR2
CALL_enter_from_user_mode
__context_tracking_exit()
trace_user_exit(0)
#PF // modifies CR2
call do_page_fault
address = read_cr2(); /* whoopsie */
And similar for i386.
Fix it by pulling the CR2 read into the entry code, before any of that
stuff gets a chance to run and ruin things.
Reported-by: He Zhe <zhe.he@windriver.com>
Reported-by: Eiichi Tsukata <devel@etsukata.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Cc: bp@alien8.de
Cc: rostedt@goodmis.org
Cc: torvalds@linux-foundation.org
Cc: hpa@zytor.com
Cc: dave.hansen@linux.intel.com
Cc: jgross@suse.com
Cc: joel@joelfernandes.org
Link: https://lkml.kernel.org/r/20190711114336.116812491@infradead.org
Debugged-by: Steven Rostedt <rostedt@goodmis.org>
PVH guest needs PV extentions to work, so "nopv" parameter should be
ignored for PVH but not for HVM guest.
If PVH guest boots up via the Xen-PVH boot entry, xen_pvh is set early,
we know it's PVH guest and ignore "nopv" parameter directly.
If PVH guest boots up via the normal boot entry same as HVM guest, it's
hard to distinguish PVH and HVM guest at that time. In this case, we
have to panic early if PVH is detected and nopv is enabled to avoid a
worse situation later.
Remove static from bool_x86_init_noop/x86_op_int_noop so they could be
used globally. Move xen_platform_hvm() after xen_hvm_guest_late_init()
to avoid compile error.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Juergen Gross <jgross@suse.com>
.. as "nopv" support needs it to be changeable at boot up stage.
Checkpatch reports warning, so move variable declarations from
hypervisor.c to hypervisor.h
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Juergen Gross <jgross@suse.com>
In virtualization environment, PV extensions (drivers, interrupts,
timers, etc) are enabled in the majority of use cases which is the
best option.
However, in some cases (kexec not fully working, benchmarking)
we want to disable PV extensions. We have "xen_nopv" for that purpose
but only for XEN. For a consistent admin experience a common command
line parameter "nopv" set across all PV guest implementations is a
better choice.
There are guest types which just won't work without PV extensions,
like Xen PV, Xen PVH and jailhouse. add a "ignore_nopv" member to
struct hypervisor_x86 set to true for those guest types and call
the detect functions only if nopv is false or ignore_nopv is true.
Suggested-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
This reverts commit ca5d376e17072c1b60c3fee66f3be58ef018952d.
Commit 8990cac6e5ea ("x86/jump_label: Initialize static branching
early") adds jump_label_init() call in setup_arch() to make static
keys initialized early, so we could use the original simpler code
again.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Juergen Gross <jgross@suse.com>
At release_thread(), ->mm is NULL; and it is fine for the former mm to
still have an LDT. Delete this check in process_64.c, similar to
commit 2684927c6b93 ("[PATCH] x86: Deprecate useless bug"), which did the
same in process_32.c.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190712224152.13129-1-jannh@google.com
This fixes the following coccinelle warning:
./arch/x86/kernel/e820.c:89:9-10: WARNING: return of 0/1 in function '_e820__mapped_any' with return type bool
Return type bool instead of 0/1.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1563158829-44373-1-git-send-email-wang.yi59@zte.com.cn
There are many compiler warnings like this,
In file included from ./arch/x86/include/asm/smp.h:13,
from ./arch/x86/include/asm/mmzone_64.h:11,
from ./arch/x86/include/asm/mmzone.h:5,
from ./include/linux/mmzone.h:969,
from ./include/linux/gfp.h:6,
from ./include/linux/mm.h:10,
from arch/x86/kernel/apic/io_apic.c:34:
arch/x86/kernel/apic/io_apic.c: In function 'check_timer':
./arch/x86/include/asm/apic.h:37:11: warning: comparison of unsigned
expression >= 0 is always true [-Wtype-limits]
if ((v) <= apic_verbosity) \
^~
arch/x86/kernel/apic/io_apic.c:2160:2: note: in expansion of macro
'apic_printk'
apic_printk(APIC_QUIET, KERN_INFO "..TIMER: vector=0x%02X "
^~~~~~~~~~~
./arch/x86/include/asm/apic.h:37:11: warning: comparison of unsigned
expression >= 0 is always true [-Wtype-limits]
if ((v) <= apic_verbosity) \
^~
arch/x86/kernel/apic/io_apic.c:2207:4: note: in expansion of macro
'apic_printk'
apic_printk(APIC_QUIET, KERN_ERR "..MP-BIOS bug: "
^~~~~~~~~~~
APIC_QUIET is 0, so silence them by making apic_verbosity type int.
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1562621805-24789-1-git-send-email-cai@lca.pw
When default_get_smp_config() is called with early == 1 and mpf->feature1
is non-zero, mpf is leaked because the return path does not do
early_memunmap().
Fix this and share a common exit routine.
Fixes: 5997efb96756 ("x86/boot: Use memremap() to map the MPF and MPC data")
Reported-by: Cfir Cohen <cfir@google.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907091942570.28240@chino.kir.corp.google.com
