IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Some SoCs support only pin change interrupts on GPIO pins used as irq
lines.
The ads7846 core is not affected from the additional irqs on the rising
edge because the code accounts touch bounce anyway by kicking in a timer
and disabling the irq after the first request and reenabling the irq after
a timeout when there is no longer pen down detected.
Signed-off-by: Michael Roth <mroth@nessie.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The touchscreen works in two modes, wait trigger mode and auto-semi
mode. The device starts in wait trigger mode and waits until pressure
is detected, then device sets WT_INT bit and raises an interrupt.
The driver should put the device into auto-semi mode and prepare for
reading first X and then Y coordinates. When coordinate data is ready
the driver sets ADC_INT bit and raises interrupt again.
[dtor@mail.ru: various cleanups]
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The appletouch driver is prone to reporting multiple fingers when only
one is pressing. The appletouch driver queries an array of pressure
sensors and counts local maxima in pressure to determine the number of
fingers. It just does this on the raw values, so a data stream like:
0 100 250 300 299 300 250 100 0
actually registers as 2 fingers.
This patch updates the logic to ignore small dips in pressure that are
less than the threshold.
Signed-off-by: Jeremy Huddleston <jeremyhu@freedesktop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: libps2 - better handle bad scheduler decisions
Input: usb1400_ts - fix access to "device data" in resume function
Input: multitouch - augment event semantics documentation
Input: multitouch - add tracking ID to the protocol
Sometimes devices send us their responses in time but due to
unfortunate scheduling decisions the receiving thread does not
get scheduled till much later and we erroneously decide that
device timed out. Work around this problem by checking whether we
received the data we needed instead of checking timeout
condition.
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
platform_data != driver_data
driver data is actually the "correct" place of the struct however it is
not placed there due to the need of the ac97 struct. This is broken since
d9105c2b01 aka "[ARM] 5184/1: Split ucb1400_ts into core and touchscreen"
Signed-off-by: Manuel Traut <manut@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are a few multi-touch devices that support finger tracking
well in hardware, Stantum being the prime example. By exposing the
tracking ID in the MT protocol, evdev bandwidth and cpu usage in
user space can be reduced.
This patch adds the ABS_MT_TRACKING_ID to the MT protocol.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Stéphane Chatty <chatty@enac.fr>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.
Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a driver for EETI's I2C connected touchscreens.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Tested-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
No point in using atomic bitops when setting the input device keybits.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
lm8323 is the keypad driver used in n810 device.
[akpm@linux-foundation.org: coding-style fixes]
[dtor@mail.ru: various cleanups]
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It appears that when the XO touchpad unit resets from ESD, it sends AA
AA instead of AA 00, the psmouse-base code handles the case of AA 00 by
triggering a serio reconnect for the port, causing a full reprobe of
the device.
Testing with OFW shows that this is likely to solve the problem, so
the attached patch simply expands the existing test to also catch AA AA.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The platform codes must provide get_pendown_state() for the driver
to work properly.
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The destruction of a input device in uinput is triggered by an ioctl().
If a process tries to destroy an input device while other is uploading a
force feedback effect by evdev to the same device, they'll deadlock.
This patch fixes the problem by flushing all pending FF uploads before
destroying the device and preventing new uploads during this operation.
[dtor@mail.ru: fix logic that ensures we don't submit new requests
to the device that is being destroyed.]
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: tsc2007 - fix locking in hrtimer handler
Input: atkbd - add force release keys quirk for Amilo Xi 3650
Input: ff-memless - fix signed to unsigned bit overflow
Input: joydev - blacklist digitizers
Now that hrtimers are always running in hard irq context we can't
unconditionally enable interrupts at the end of the timer function.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For evdev, joydev and mousedev, instead of having a separate character array
holding name of the handle, use struct devce's name which is the same.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When we get a relative packet from trackpoint (when we deal with
touchscreen/trackpoint combo) we should not send events for the device
corresponding to touchscreen as it confuses evtouch driver (it looks
like it keeps previously reported absolute coordinates and the cursor
stays in the same place).
Reported-by: Marcin Drewka <laimoriel@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Dell Latitude D630/D800 have DualPoint (touchpad plus trackpoint)
instead of a simple touchpad and a pass-through port for external
PS/2 mouse.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When userspace sets effect->u.rumble.strong_magnitude to 0x8001 or
larger, ml_combine_effects() would always return strong_magnitude
0xffff.
Problem is that 'gain' is passed in as signed integer. Multiplying
magnitude (__u16) with gain (int) causes magnitude read as signed and
results negative value (with magnitude > 0x8000). This signed integer
is then divided and value, still negative, converted to 32bit unsigned
integer. Finally checking combine overflow min(new+old, 0xffff) gives
out 0xffff.
Fix is to simply change 'gain' to unsigned int.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
BTN_TOUCH is not set by the wacom driver which causes it to be handled by the
joydev driver while the resulting device is broken. This causes problems with
applications that try to use a joystick device.
Ubuntu BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/300143
Signed-off-by: Tim Cole <tim.cole@canonical.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Acked-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: document the multi-touch (MT) protocol
Input: add detailed multi-touch finger data report protocol
Input: allow certain EV_ABS events to bypass all filtering
Input: bcm5974 - add documentation for the driver
Input: bcm5974 - augment debug information
Input: bcm5974 - Add support for the Macbook 5 (Unibody)
Input: bcm5974 - add quad-finger tapping
Input: bcm5974 - prepare for a new trackpad header type
Input: appletouch - fix DMA to/from stack buffer
Input: wacom - fix TabletPC touch bug
Input: lifebook - add DMI entry for Fujitsu B-2130
Input: ALPS - add signature for Toshiba Satellite Pro M10
Input: elantech - make sure touchpad is really in absolute mode
Input: elantech - provide a workaround for jumpy cursor on firmware 2.34
Input: ucb1400 - use disable_irq_nosync() in irq handler
Input: tsc2007 - use disable_irq_nosync() in irq handler
Input: sa1111ps2 - use disable_irq_nosync() in irq handlers
Input: omap-keypad - use disable_irq_nosync() in irq handler
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In order to utilize the full power of the new multi-touch devices, a
way to report detailed finger data to user space is needed. This patch
adds a multi-touch (MT) protocol which allows drivers to report details
for an arbitrary number of fingers.
The driver sends a SYN_MT_REPORT event via the input_mt_sync() function
when a complete finger has been reported.
In order to stay compatible with existing applications, the data
reported in a finger packet must not be recognized as single-touch
events. In addition, all finger data must bypass input filtering,
since subsequent events of the same type refer to different fingers.
A set of ABS_MT events with the desired properties are defined. The
events are divided into categories, to allow for partial implementation.
The minimum set consists of ABS_MT_TOUCH_MAJOR, ABS_MT_POSITION_X and
ABS_MT_POSITION_Y, which allows for multiple fingers to be tracked.
If the device supports it, the ABS_MT_WIDTH_MAJOR may be used to provide
the size of the approaching finger. Anisotropy and direction may be
specified with ABS_MT_TOUCH_MINOR, ABS_MT_WIDTH_MINOR and
ABS_MT_ORIENTATION. Devices with more granular information may specify
general shapes as blobs, i.e., as a sequence of rectangular shapes
grouped together by a ABS_MT_BLOB_ID. Finally, the ABS_MT_TOOL_TYPE
may be used to specify whether the touching tool is a finger or a pen.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With the upcoming multi-touch interface as an example, there is
a need to make certain that all reported events actually get passed
to the event handler. This patch equips the input core with the
ability to bypass all filtering for certain EV_ABS events.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for the new unibody Macbook, with physically
integrated button and trackpad. Since the integrated button changes
the logic for touch-and-click, a device capability bit mask is now
reported in input_id.version, which can be picked up by user space
via a EVIOCGID call.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: David M. Lary <dmlary@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The integrated button on the new unibody Macbooks presents a need to
report explicit four-finger actions. Evidently, the finger pressing
the button is also touching the trackpad, so in order to fully support
three-finger actions, the driver must be able to report four-finger
actions. This patch adds a new button, BTN_TOOL_QUADTAP, which
achieves this.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The new unibody Macbooks are equipped with an integrated button and
trackpad. The package header of the trackpad interface has changed to
also contain information about the integrated button. This patch
performs the necessary preparations to allow for the new package
header.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_DMA_API_DEBUG spotted an instance of appletouch using
an array on the stack as a DMA buffer for certain hardware.
Change it to use a kmalloc()ed buffer instead.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixed a bug that was introduced in kernel 2.6.28 for
TabletPC touch data. The wacom_parse_hid routine in wacom_sys.c
should always return 0 even when usb_control_msg got an error.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Although we already have entry for ZEPHYR the match is done
on product name whereas B-2130 BIOS has it in board name.
Reported-by: Yuriy Zhuravlev <stalkerg@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This toshiba has a touchpad with trackpoint and 2 sets of left
and right buttons (above and below touchpad).
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Simple input driver support for the events reported by the
MSP430 firmware on the DM355 EVM. Verified using the RC5
remote included with the kit; docs weren't quite right.
Some of the keycode selections might need improvement; they
can be remapped, so there's at least a runtime workaround.
(I also suspect Linux may someday merit more generic support
for RC5 based remote controls.)
These events don't distinguish key press vs release events,
so this reports both and then skips the next event if it's
identical. The RC5 remote codes include a "toggle" bit that
can help detect autorepeated keys; but this driver doesn't
bother with those nuances.
This driver relies on the drivers/mfd/dm355evm_msp.c code
for core features, including sharing I2C access to this
firmware with GPIO, LED, and RTC support.
[dtor@mail.ru: fix error unwindng path in probe()]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On parisc machines, which don't have HIL, removing the hp_sdc module
panics the kernel. Fix this by returning early in hp_sdc_exit() if no HP
SDC controller was found.
Add functionality to probe for the hp_sdc_mlc kernel module (which takes
care of the upper layer HIL functionality on parisc) after two seconds.
This is needed to get all the other HIL drivers (keyboard / mouse/ ..)
drivers automatically loaded by udev later as well.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Frans Pop <elendil@planet.nl>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is part of the twl4030 multifunction device driver that supports
reporting KEY_POWER events via the input layer.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is a keyboard driver for the Cirrus Logic EP93xx keypad matrix
peripheral. This driver is based on the pxa27x_keypad driver.
[dtor@mail.ru: Plug in input_dev->keycode so keymap can be changed
from userspace.]
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds an accelerated driver for Atmel AVR32 AT32AP700X
microprocessors. It uses interrupts on the channel B in the AC97
controller. Thus, offloading the work queue in the wm97xx-ts driver.
The driver has been tested with Atmel AVR32 AT32AP7000 and Wolfson
WM9712 codec.
The driver can also be easily modified to support Atmel AT91 devices, as
AT91 and AVR32 share the same AC97C module.
[Fixed leak of atmel_wm97xx when probe fails. -- broonie]
[dtor@mail.ru: do not report ABS_PRESSURE events when not measuring pressure]
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There exist laptops with Elantech touchpads where switching to absolute mode
does not happen, although writing the configuration register succeeds
without error. Reading back the register afterwards reveils that the
absolute mode bit is not set as if masked out by the touchpad firmware.
Always read back register 0x10, make sure that for hardware version 1 the
absolute mode bit is actually set and fail otherwise. This prevents the case
where the touchpad is claimed by the Elantech driver but is nonetheless not
working.
Signed-off-by: Arjan Opmeer <arjan@opmeer.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It seems that Elantech touchpad firmware version 2.34 on the Hercules eCAFÉ
suffers from a problem where bogus coordinates get reported at the beginning
of a touch action. This causes the mouse cursor or the scrolled page to
jump.
Included patch provides a workaround that discards mouse packets that are
likely to contain bogus coordinates. The workaround is activated when we
detect touchpad with fimware version 2.34.
Signed-off-by: Arjan Opmeer <arjan@opmeer.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
