IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
In VRR mode, keep track of the vblank count of the last
completed pageflip in amdgpu_crtc->last_flip_vblank, as
recorded in the pageflip completion handler after each
completed flip.
Use that count to prevent mmio programming a new pageflip
within the same vblank in which the last pageflip completed,
iow. to throttle pageflips to at most one flip per video
frame, while at the same time allowing to request a flip
not only before start of vblank, but also anywhere within
vblank.
The old logic did the same, and made sense for regular fixed
refresh rate flipping, but in vrr mode it prevents requesting
a flip anywhere inside the possibly huge vblank, thereby
reducing framerate in vrr mode instead of improving it, by
delaying a slightly delayed flip requests up to a maximum
vblank duration + 1 scanout duration. This would limit VRR
usefulness to only help applications with a very high GPU
demand, which can submit the flip request before start of
vblank, but then have to wait long for fences to complete.
With this method a flip can be both requested and - after
fences have completed - executed, ie. it doesn't matter if
the request (amdgpu_dm_do_flip()) gets delayed until deep
into the extended vblank due to cpu execution delays. This
also allows clients which want to regulate framerate within
the vrr range a much more fine-grained control of flip timing,
a feature that might be useful for video playback, and is
very useful for neuroscience/vision research applications.
In regular non-VRR mode, retain the old flip submission
behavior. This to keep flip scheduling for fullscreen X11/GLX
OpenGL clients intact, if they use the GLX_OML_sync_control
extensions glXSwapBufferMscOML(, ..., target_msc,...) function
with a specific target_msc target vblank count.
glXSwapBuffersMscOML() or DRI3/Present PresentPixmap() will
not flip at the proper target_msc for a non-zero target_msc
if VRR mode is active with this patch. They'd often flip one
frame too early. However, this limitation should not matter
much in VRR mode, as scheduling based on vblank counts is
pretty futile/unusable under variable refresh duration
anyway, so no real extra harm is done.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When a dce80 asic was suspended, the clocks were not set to 0.
Upon resume, the new clock was compared to the existing clock,
they were found to be the same, and so the clock was not set.
This resulted in a blackscreen.
[How]
In atomic commit, check to see if there are any active pipes.
If no, set clocks to 0
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
optimize_bandwidth was using dce100_prepare_bandwidth this is incorrect
[How]
change it to dce100_optimize_bandwidth
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
If the cursor pos passed from DM is less than the plane_state->dst_rect
top left corner then the unsigned cursor pos wraps around to a large
positive number since cursor pos is a u32.
There was an attempt to guard against this in hubp1_cursor_set_position
by checking the src_x_offset and src_y_offset and offseting the
cursor hotspot within hubp1_cursor_set_position.
However, the cursor position itself is still being programmed
incorrectly as a large value.
This manifests itself visually as the cursor disappearing or containing
strange artifacts near the middle of the screen on raven.
[How]
Don't subtract the destination rect top left corner from the pos but
add it to the hotspot instead. This happens before the pos gets
passed into hubp1_cursor_set_position.
This achieves the same result but avoids the subtraction wrap around.
With this fix the original cursor programming logic can be used again.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Murton Liu <Murton.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The visual corruption due to low display clock value.
Observed on Carrizo 4K@60Hz.
[How]
There was earlier patch for dce_update_clocks:
Adding +15% workaround also to to dce11_update_clocks
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
drm_dp_mst_topology_mgr_suspend() is added into the new reboot
sequence, which disables the UP request at the beginning.
Therefore sideband messages are blocked.
[How]
Finish MST sideband message transaction before UP request is
suppressed.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
It's useful to know the min and max vrr range for IGT testing.
[How]
Expose the min and max vfreq for the connector via a debugfs file
on the connector, "vrr_range".
Example usage: cat /sys/kernel/debug/dri/0/DP-1/vrr_range
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDP was missing in the checks for supported VRR connectors.
[How]
Attach the properties for eDP connectors too.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202449
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The earlier change 'Fix 6x4K displays' led to fclk value
idling at higher DPM level.
[How]
Apply the fix only to respective multi-display configuration.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Backlight is conceptually a property of links, not streams.
All backlight programming is done on links, but there is a
stream property bl_pwm_level that is used to restore backlight
on dpms on and s3 resume. This is unnecessary, as backlight
is already restored by hardware with no driver intervention.
[How]
Remove bl_pwm_level, and the stream argument to set_backlight
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=109375
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 923fe4951282cbdfce05186c10380bbc45b5e03b)
[Why]
The cursor vanishes when touching the top of edge of the screen for
Raven on Linux.
This occurs because the cursor height is not taken into account when
deciding to disable the cursor.
[How]
Factor in the cursor height into the cursor calculations - and mimic
the existing x position calculations.
Fixes: 94a4ffd1d40b ("drm/amd/display: fix PIP bugs on Dal3")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hotplug on raven results in REG_WAIT_TIMEOUT warning
due to failing attempt to lock disabled otg for the hubp
interdependent pipes programming.
[How]
Don't setup pipe interdependencies for disabled otg.
Also removed the unnecessary duplicate logic checks.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PPLIB not receive the PME when unplug.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This fixes a stuttering issue that occurs when moving a hardware cursor
when VRR is enabled.
Previously when VRR is enabled atomic check will grab the connector
state for every atomic update. This has to lock the connector in order
to do so. The locking is bad enough by itself for performance, but
it gets worse with what we do just below that - add all the planes
for the CRTC to the commit.
This prevents the cursor fast path from working - there's more than one
plane now. With state->allow_modeset = true on top of this, it also
adds and removes all the planes from the DC context triggering a full
(very slow) update in DC.
[How]
We need the connector state to get the VRR min/max capbilities, but we
only need them when there's a CRTC mode change or when VRR is toggled.
The condition has been updated accordingly.
Fixes: 3cc22f281318 ("drm/amdgpu: Set FreeSync state using drm VRR properties")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the DMCU's iRAM definition was moved to the newly created
power_helpers, a #pragma pack was lost, causing the iRAM to be misaligned
[How]
Restore the #pragma pack
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is an ugly one unfortunately. Currently, all DRM drivers supporting
atomic modesetting will save the state that userspace had set before
suspending, then attempt to restore that state on resume. This probably
worked very well at one point, like many other things, until DP MST came
into the picture. While it's easy to restore state on normal display
connectors that were disconnected during suspend regardless of their
state post-resume, this can't really be done with MST because of the
fact that setting up a downstream sink requires performing sideband
transactions between the source and the MST hub, sending out the ACT
packets, etc.
Because of this, there isn't really a guarantee that we can restore the
atomic state we had before suspend once we've resumed. This sucks pretty
bad, but so far I haven't run into any compositors that this actually
causes serious issues with. Most compositors will notice the hotplug we
send afterwards, and then reprobe state.
Since nouveau and i915 also don't fail the suspend/resume process due to
failing to restore the atomic state, let's make amdgpu match this
behavior. Better to resume the GPU properly, then to stop the process
half way because of a potentially unavoidable atomic commit failure.
Eventually, we'll have a real fix for this problem on the DRM level. But
we've got some more important low-hanging fruit to deal with first.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://patchwork.freedesktop.org/patch/msgid/20190108211133.32564-3-lyude@redhat.com
drm_dp_mst_topology_mgr_resume() returns whether or not it managed to
find the topology in question after a suspend resume cycle, and the
driver is supposed to check this value and disable MST accordingly if
it's gone-in addition to sending a hotplug in order to notify userspace
that something changed during suspend.
Currently, amdgpu just makes the mistake of ignoring the return code
from drm_dp_mst_topology_mgr_resume() which means that if a topology was
removed in suspend, amdgpu never notices and assumes it's still
connected which leads to all sorts of problems.
So, fix this by actually checking the rc from
drm_dp_mst_topology_mgr_resume(). Also, reformat the rest of the
function while we're at it to fix the over-indenting.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://patchwork.freedesktop.org/patch/msgid/20190108211133.32564-2-lyude@redhat.com
-----BEGIN PGP SIGNATURE-----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=hFld
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-01-05' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Happy New Year, just decloaking from leave to get some stuff from the
last week in before rc1:
core:
- two regression fixes for damage blob and atomic
i915 gvt:
- Some missed GVT fixes from the original pull
amdgpu:
- new PCI IDs
- SR-IOV fixes
- DC fixes
- Vega20 fixes"
* tag 'drm-next-2019-01-05' of git://anongit.freedesktop.org/drm/drm: (53 commits)
drm: Put damage blob when destroy plane state
drm: fix null pointer dereference on null state pointer
drm/amdgpu: Add new VegaM pci id
drm/ttm: Use drm_debug_printer for all ttm_bo_mem_space_debug output
drm/amdgpu: add Vega20 PSP ASD firmware loading
drm/amd/display: Fix MST dp_blank REG_WAIT timeout
drm/amd/display: validate extended dongle caps
drm/amd/display: Use div_u64 for flip timestamp ns to ms
drm/amdgpu/uvd:Change uvd ring name convention
drm/amd/powerplay: add Vega20 LCLK DPM level setting support
drm/amdgpu: print process info when job timeout
drm/amdgpu/nbio7.4: add hw bug workaround for vega20
drm/amdgpu/nbio6.1: add hw bug workaround for vega10/12
drm/amd/display: Optimize passive update planes.
drm/amd/display: verify lane status before exiting verify link cap
drm/amd/display: Fix bug with not updating VSP infoframe
drm/amd/display: Add retry to read ddc_clock pin
drm/amd/display: Don't skip link training for empty dongle
drm/amd/display: Wait edp HPD to high in detect_sink
drm/amd/display: fix surface update sequence
...
[why]
Some dongle doesn't have a valid extended dongle caps,
but we still set the extended dongle caps to be valid.
This causes validation fails for all timing.
[how]
If no dp_hdmi_max_pixel_clk is provided,
don't use extended dongle caps.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Resolves __udivdi3 missing errors when building for i386.
Fixes: 6378ef012ddc ("drm/amd/display: Add below the range support for FreeSync")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
passive update planes still spends a litte more
time on some cases.
[How]
Remove unnecessary trace which involving in some register read.
Disable debug output for release build.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP LL CTS1.4 4.3.2.1 test failure.
[how]
The failure is caused by not handling DP link loss
hpd short pusle during set mode. The change is to read link status
before set mode link training. If link is lost, re-verify link caps.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently, when the VSP infopacket is rebuilt in DM, it is not updated
when being programmed in encoder.
[HOW]
Add new VSP case for update_info_frame
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On customer board, there is one pluse (1v , < 1ms) on
DDC_CLK pin when plug / unplug DP cable. Driver will read
it and config DP to HDMI/DVI dongle.
[HOW]
If there is a real dongle, DDC_CLK should be always pull high.
Try to read again to recovery this special case. Retry times = 3.
Need additional 3ms to detect DP passive dongle(3 failures)
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Skipping initial link training will result in no verified link cap for
mode enumeration. Some versions of the BIOS seem to have PHY programming
sequence issue as well if initial link training is skipped, resulting in
a softlock in BIOS command table.
[How]
Identify the empty dongle hotplug case, and still do initial link
training.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In 99% user case, edp will be post by vbios.
In 1% / current case: Lenovo don't light up edp panel in vbios
post stage, vbios won't be lit up. Thus in dal when we init DCN
10 hw, we power up edp, then we start detect_sink, but internal
time is too short, when we detect it, HPD is still low, so we don't
detect the edp, and edp shows black.
[How]
When we init hw, we wait edp HPD to high after power up edp.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
An earlier change added update of interdependent dlg/ttu params for pipes
not being updated in the current call. The code fails to check if the other
pipes are actually active yet causing an assert.
This change adds a check for surface presence on the pipes before updating
the interdepenednt params.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
YCbCr420 packing format uses two chanels for luma, and 1
channel for both chroma component. Our previous implementation
did not account for this and results in every other pixel having
very high luma value, showing greyish color instead of black.
YCbCr444 = <Y1, Cb1, Cr1>; <Y2, Cb2, Cr2> .....
YCbCr420 = <Y1, Y2, Cb1>; <Y3, Y4, Cr1> .....
[How]
Program the second channel with the black color value for luma
as well.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Hugo Hu <Hugo.Hu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC warns when a REG_WAIT takes a while and full-on errors
with stack dump on REG_WAIT timeout. Most of the time it isn't
a real issue.
[How]
Make DC cool its jets - taking a while is a debug message (because
it is not something that normal users should need to be aware of),
and timeouts are warnings (because it technically shouldn't
happen, but it's not a big deal if it does)
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is a dual channel format and should be treated like other
video formats
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In certain configurations, such as PX configs or some Vega20 parts
DC gets created without connectors.
[How]
Drop the dm_error print when no connectors.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When XGMI is enabled, the DP reference clock needs to be adjusted
according to the XGMI spread spectrum percentage and mode. But first,
we need the ability to fetch this info.
[How]
Within the BIOS parser, Read from vBIOS when XGMI SS info is requested.
In addition, diags build uses include_legacy/atomfirmware.h for the
smu_info_v3_3 table headers. Update that as well.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We'll need a way to differentiate Vega 20 in DC
[How]
Add a DCE_VERSION_12_1 enum, which will be returned as the DC version if
the ASIC used is a Vega 20.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the flip-rate is below the minimum supported variable refresh rate
range for the monitor the front porch wait will timeout and be
frequently misaligned resulting in stuttering and/or flickering.
The FreeSync module can still maintain a smooth and flicker free
image when the monitor has a refresh rate range such that the maximum
refresh > 2 * minimum refresh by utilizing low framerate compensation,
"below the range".
[How]
Hook up the pre-flip and post-flip handlers from the FreeSync module.
These adjust the minimum/maximum vrr range to duplicate frames
when appropriate by tracking flip timestamps.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The visual corruption due to low display clock value observed on some
systems
[How]
There was earlier patch for dspclk:
'drm/amd/display: Raise dispclk value for dce_update_clocks'
Adding +15% workaround also to to dce112_update_clocks
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Leo Li <Sunpeng.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The behavior of drm_atomic_helper_cleanup_planes differs depending on
whether the commit was asynchronous or not. When it's called from
amdgpu_dm_atomic_commit_tail during a typical atomic commit the
plane state has been swapped so it calls cleanup_fb on the old plane
state.
However, in the asynchronous commit codepath the call to
drm_atomic_helper_commit also calls dm_plane_helper_cleanup_fb after
atomic_async_update has been called. Since the plane state is updated
in place and has not been swapped the cleanup_fb call affects the new
plane state.
This results in a use after free for the given sequence:
- Fast update, fb1 pin/ref, fb1 unpin/unref
- Fast update, fb2 pin/ref, fb2 unpin/unref
- Slow update, fb1 pin/ref, fb2 unpin/unref
- Fast update, fb2 pin/ref -> use after free. bug
[How]
Disallow framebuffer changes in the fast path. Since this includes
a NULL framebuffer, this means that only framebuffers that have
been previously pin+ref at least once will be used, preventing a
use after free.
This has a significant throughput reduction for cursor updates where
the framebuffer changes. For most desktop usage this isn't a problem,
but it does introduce performance regressions for two specific IGT
tests:
- cursor-vs-flip-toggle
- cursor-vs-flip-varying-size
Fixes: 2cc751931afc ("drm/amd/display: Add fast path for cursor plane updates")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Legacy cursor plane updates from drm helpers go through the full
atomic codepath. A high volume of cursor updates through this slow
code path can cause subsequent page-flips to skip vblank intervals
since each individual update is slow.
This problem is particularly noticeable for the compton compositor.
[How]
A fast path for cursor plane updates is added by using DRM asynchronous
commit support provided by async_check and async_update. These don't do
a full state/flip_done dependency stall and they don't block other
commit work.
However, DC still expects itself to be single-threaded for anything
that can issue register writes. Screen corruption or hangs can occur
if write sequences overlap. Every call that potentially perform
register writes needs to be guarded for asynchronous updates to work.
The dc_lock mutex was added for this.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106175
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These properties aren't being carried over when the atomic state.
This tricks atomic check and commit tail into performing underscan
and scaling operations when they aren't needed.
With the patch that forced scaling/RMX_ASPECT on by default this
results in many unnecessary surface updates and hangs under certain
conditions.
[How]
Duplicate the properties.
Fixes: 91b66c47ba34 ("drm/amd/display: Set RMX_ASPECT as default")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the "max bpc" isn't explicitly set in the atomic state then it
have a value of 0. This has the correct behavior of limiting a panel
to 8bpc in the case where the panel supports 8bpc. In the case of eDP
panels this isn't a true assumption - there are panels that can only
do 6bpc.
Banding occurs for these displays.
[How]
Initialize the max_bpc when the connector resets to 8bpc. Also carry
over the value when the state is duplicated.
Bugzilla: https://bugs.freedesktop.org/108825
Fixes: 307638884f72 ("drm/amd/display: Support amdgpu "max bpc" connector property")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 91b66c47ba3468f7882ea4a84d5e0e0c186b638f.
Forcing RMX_ASPECT as default uses the preferred/native mode's timings
for any mode the user selects and scales the image. This provides a
a consistently nicer result in the case where the selected mode's
refresh rate matches the native mode's refresh but this isn't always
the case.
For example, if the monitor is 1080p@144Hz and the preferred mode is
60Hz then even if the user selects 1080p@144Hz as their selected mode
they'll get 1080p@60Hz.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Tracing is a useful and cheap debug functionality
[How]
This creates a new trace system amdgpu_dm, currently with
three trace events
amdgpu_dc_rreg and amdgpu_dc_wreg report the address and value
of any dc register reads and writes
amdgpu_dc_performance requires at least one of those two to be
enabled. It counts the register reads and writes since the
last entry
v2: Don't check for NULL before kfree
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
New GCC warnings for stringop-truncation and stringop-overflow help
catch common misuse of strncpy. This patch suppresses these warnings
by fixing bugs identified by them.
[How]
Since the parameter passed for name in amdpgu_dm_create_common_mode has
no fixed length, if the string is >= DRM_DISPLAY_MODE_LEN then
mode->name will not be null-terminated.
The truncation in fill_audio_info won't actually occur (and the string
will be null-terminated since the buffer is initialized to zero), but
the warning can be suppressed by using the proper buffer size.
This patch fixes both issues by using the real size for the buffer and
making use of strscpy (which always terminates).
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prepare for clock debug logging. With the exception of removing
max_supported_dppclk_khz from logs, there are no functional changes.
[How]
Add clk_bypass struct and clean up buffer logic
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Su Chung <Su.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Steven Chiu <steven.chiu@amd.com>
Reviewed-by: Fatemeh Darbehani <Fatemeh.Darbehani@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dce100 was set to always pass safe_to_lower = false
to the clock manager
Thus, on suspend the clocks were not being set to 0
which is incorrect behaviour
This was causing s3 resume to blackscreen on intel
CPUs with dce100 GPUs attached
(Note that the hash in this Fixes: tag is the hash on Alex's tree)
Fixes: ae7d8aeb38d7 ("drm/amd/display: remove safe_to_lower flag from dc, use 2 functions instead")
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dithering needs to be enabled or disabled as requested. If
dc_stream_update->dither_option is non-null, program the FMT blocks.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When running igt@kms_plane@pixel-format-pipe-* tests the CRC read will
time out and the test will fail.
This is because the CRTC is duplicated but the crc_enabled parameter
isn't copied over to the new dm_crtc_state. CRC reads will time out
because amdgpu_dm_crtc_handle_crc_irq will no longer call
drm_crtc_add_crc_entry.
[How]
Copy crc_enabled when duplicating the state.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
add customizable log with a message input, which is for adding
test log in debugging as printf function in ETW.
[Usage]
EVENT_LOG_CUST_MSG1("TestLog","Hello World %d=0x%x", 123, pDC);
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
