IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[Why]
When a dce80 asic was suspended, the clocks were not set to 0.
Upon resume, the new clock was compared to the existing clock,
they were found to be the same, and so the clock was not set.
This resulted in a blackscreen.
[How]
In atomic commit, check to see if there are any active pipes.
If no, set clocks to 0
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
optimize_bandwidth was using dce100_prepare_bandwidth this is incorrect
[How]
change it to dce100_optimize_bandwidth
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
If the cursor pos passed from DM is less than the plane_state->dst_rect
top left corner then the unsigned cursor pos wraps around to a large
positive number since cursor pos is a u32.
There was an attempt to guard against this in hubp1_cursor_set_position
by checking the src_x_offset and src_y_offset and offseting the
cursor hotspot within hubp1_cursor_set_position.
However, the cursor position itself is still being programmed
incorrectly as a large value.
This manifests itself visually as the cursor disappearing or containing
strange artifacts near the middle of the screen on raven.
[How]
Don't subtract the destination rect top left corner from the pos but
add it to the hotspot instead. This happens before the pos gets
passed into hubp1_cursor_set_position.
This achieves the same result but avoids the subtraction wrap around.
With this fix the original cursor programming logic can be used again.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Murton Liu <Murton.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The visual corruption due to low display clock value.
Observed on Carrizo 4K@60Hz.
[How]
There was earlier patch for dce_update_clocks:
Adding +15% workaround also to to dce11_update_clocks
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The earlier change 'Fix 6x4K displays' led to fclk value
idling at higher DPM level.
[How]
Apply the fix only to respective multi-display configuration.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Backlight is conceptually a property of links, not streams.
All backlight programming is done on links, but there is a
stream property bl_pwm_level that is used to restore backlight
on dpms on and s3 resume. This is unnecessary, as backlight
is already restored by hardware with no driver intervention.
[How]
Remove bl_pwm_level, and the stream argument to set_backlight
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=109375
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 923fe4951282cbdfce05186c10380bbc45b5e03b)
[Why]
The cursor vanishes when touching the top of edge of the screen for
Raven on Linux.
This occurs because the cursor height is not taken into account when
deciding to disable the cursor.
[How]
Factor in the cursor height into the cursor calculations - and mimic
the existing x position calculations.
Fixes: 94a4ffd1d40b ("drm/amd/display: fix PIP bugs on Dal3")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hotplug on raven results in REG_WAIT_TIMEOUT warning
due to failing attempt to lock disabled otg for the hubp
interdependent pipes programming.
[How]
Don't setup pipe interdependencies for disabled otg.
Also removed the unnecessary duplicate logic checks.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PPLIB not receive the PME when unplug.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some dongle doesn't have a valid extended dongle caps,
but we still set the extended dongle caps to be valid.
This causes validation fails for all timing.
[how]
If no dp_hdmi_max_pixel_clk is provided,
don't use extended dongle caps.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
passive update planes still spends a litte more
time on some cases.
[How]
Remove unnecessary trace which involving in some register read.
Disable debug output for release build.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP LL CTS1.4 4.3.2.1 test failure.
[how]
The failure is caused by not handling DP link loss
hpd short pusle during set mode. The change is to read link status
before set mode link training. If link is lost, re-verify link caps.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently, when the VSP infopacket is rebuilt in DM, it is not updated
when being programmed in encoder.
[HOW]
Add new VSP case for update_info_frame
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On customer board, there is one pluse (1v , < 1ms) on
DDC_CLK pin when plug / unplug DP cable. Driver will read
it and config DP to HDMI/DVI dongle.
[HOW]
If there is a real dongle, DDC_CLK should be always pull high.
Try to read again to recovery this special case. Retry times = 3.
Need additional 3ms to detect DP passive dongle(3 failures)
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Skipping initial link training will result in no verified link cap for
mode enumeration. Some versions of the BIOS seem to have PHY programming
sequence issue as well if initial link training is skipped, resulting in
a softlock in BIOS command table.
[How]
Identify the empty dongle hotplug case, and still do initial link
training.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In 99% user case, edp will be post by vbios.
In 1% / current case: Lenovo don't light up edp panel in vbios
post stage, vbios won't be lit up. Thus in dal when we init DCN
10 hw, we power up edp, then we start detect_sink, but internal
time is too short, when we detect it, HPD is still low, so we don't
detect the edp, and edp shows black.
[How]
When we init hw, we wait edp HPD to high after power up edp.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
An earlier change added update of interdependent dlg/ttu params for pipes
not being updated in the current call. The code fails to check if the other
pipes are actually active yet causing an assert.
This change adds a check for surface presence on the pipes before updating
the interdepenednt params.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
YCbCr420 packing format uses two chanels for luma, and 1
channel for both chroma component. Our previous implementation
did not account for this and results in every other pixel having
very high luma value, showing greyish color instead of black.
YCbCr444 = <Y1, Cb1, Cr1>; <Y2, Cb2, Cr2> .....
YCbCr420 = <Y1, Y2, Cb1>; <Y3, Y4, Cr1> .....
[How]
Program the second channel with the black color value for luma
as well.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Hugo Hu <Hugo.Hu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC warns when a REG_WAIT takes a while and full-on errors
with stack dump on REG_WAIT timeout. Most of the time it isn't
a real issue.
[How]
Make DC cool its jets - taking a while is a debug message (because
it is not something that normal users should need to be aware of),
and timeouts are warnings (because it technically shouldn't
happen, but it's not a big deal if it does)
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is a dual channel format and should be treated like other
video formats
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In certain configurations, such as PX configs or some Vega20 parts
DC gets created without connectors.
[How]
Drop the dm_error print when no connectors.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When XGMI is enabled, the DP reference clock needs to be adjusted
according to the XGMI spread spectrum percentage and mode. But first,
we need the ability to fetch this info.
[How]
Within the BIOS parser, Read from vBIOS when XGMI SS info is requested.
In addition, diags build uses include_legacy/atomfirmware.h for the
smu_info_v3_3 table headers. Update that as well.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We'll need a way to differentiate Vega 20 in DC
[How]
Add a DCE_VERSION_12_1 enum, which will be returned as the DC version if
the ASIC used is a Vega 20.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The visual corruption due to low display clock value observed on some
systems
[How]
There was earlier patch for dspclk:
'drm/amd/display: Raise dispclk value for dce_update_clocks'
Adding +15% workaround also to to dce112_update_clocks
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Leo Li <Sunpeng.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Tracing is a useful and cheap debug functionality
[How]
This creates a new trace system amdgpu_dm, currently with
three trace events
amdgpu_dc_rreg and amdgpu_dc_wreg report the address and value
of any dc register reads and writes
amdgpu_dc_performance requires at least one of those two to be
enabled. It counts the register reads and writes since the
last entry
v2: Don't check for NULL before kfree
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prepare for clock debug logging. With the exception of removing
max_supported_dppclk_khz from logs, there are no functional changes.
[How]
Add clk_bypass struct and clean up buffer logic
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Su Chung <Su.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Steven Chiu <steven.chiu@amd.com>
Reviewed-by: Fatemeh Darbehani <Fatemeh.Darbehani@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dce100 was set to always pass safe_to_lower = false
to the clock manager
Thus, on suspend the clocks were not being set to 0
which is incorrect behaviour
This was causing s3 resume to blackscreen on intel
CPUs with dce100 GPUs attached
(Note that the hash in this Fixes: tag is the hash on Alex's tree)
Fixes: ae7d8aeb38d7 ("drm/amd/display: remove safe_to_lower flag from dc, use 2 functions instead")
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dithering needs to be enabled or disabled as requested. If
dc_stream_update->dither_option is non-null, program the FMT blocks.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
add customizable log with a message input, which is for adding
test log in debugging as printf function in ETW.
[Usage]
EVENT_LOG_CUST_MSG1("TestLog","Hello World %d=0x%x", 123, pDC);
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For more clear usage in future
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] fbc is within the data path from memory to dce. while
re-configure mc dmif, fbc should be enabled. otherwise, fbc
may not be enabled properly.
[HOW] before re-configure mc dmif, disable fbc, only after
dmif re-configuration fully done, enable fbc again.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* Use provided infopacket in stream (if valid) instead of reconstructing
in set_vendor_info_packet()
* Use proper format for enums
* Use dc info packet struct instead
Signed-off-by: Harmanprit Tatla <Harmanprit.Tatla@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Failure to read Detailed Capabilities Info.
[How]
Read Detailed Capbilities Info 80h-08Fh.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This patch is for use by dm, no need for it in dc.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are a lot of unintuitive parts of the dm-dc interface.
It would help us if these were documented to provide
a common understanding of what they are supposed to do
[How]
Most of this documentation is stubs, to be filled out more
thoroughly by the experts
Not every dm-accessible function and struct is mentioned.
Simple functions like getters, setters, retain, release,
create, destroy can be left unadorned.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Steven Chiu <steven.chiu@amd.com>
Reviewed-by: Shahin Khayyer <Shahin.Khayyer@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When there are multiple aux transaction in parallel, it is sometime
sporadically the aux transaction starts to continuously fail. The
aux transaction was failing because the busy bit for the given gpio
pin was always set. The busy bit was alway set because the
programming sequence to read, modify and write busy bit was not
atomic. Due to which when multiple threads are trying to modify the
busy bits for their gpio pins in the same integer variable sometimes
the busy bits integer variable is written with old data causing
failure.
[how]
Instead of using individual bits to track gpio pins and grouping
them to integers, one byte will be allcoated for each gpio pin.
Now whenever a gpio pin needs to be set to mark being used, only
writing a value of one to that byte is sufficient, other bytes
are not impacted. Also no need to have atomicity with bytes unlike
with bits.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
More than 4x4K didn't lightup on Vega20 due to low dcfclk value.
Powerplay expects valid min requirement for dcfclk from DC.
[How]
Update min_dcfclock_khz based on min_engine_clock value.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove dce/dce_mem_input.h which is included more than once
Signed-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adaptive Backlight Management (ABM) is a feature
that reduces backlight level to save power, while
increasing pixel contrast and pixel luminance
to maintain readability and image quality.
ABM will adjust in response to the
pixel luminance of the displayed content.
ABM is made available as a drm property on eDP
monitors called "abm level", which ranges from 0 to 4.
When this property is set to 0, ABM is off. Levels 1
to 4 represent different ranges of backlight reduction.
At higher levels both the backlight reduction and pixel
adjustment will be greater.
ABM requires DMCU firmware, which is currently available for
Raven ASICs only. If the feature does not work, please
ensure your firmware is up to date.
v2:
Fix commit message, only attach property if DMCU loaded
v3:
Store ABM level in crtc state to accommodate dc
v4:
Fix ABM saving on dpms cycle
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DMCU IRAM must be loaded by the driver before DMCU
can function.
Move the IRAM code out of the shadows and into a new file
modules/power/power_helpers.c
The IRAM table contains the backlight curve and ABM parameters
Add this new file to the Makefiles
Call dmcu_load_iram in late init of DM
Move struct dmcu_version from dc.h to dmcu.h to allow
dmcu to be included on its own
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There was a full clock request struct of which only
one value was being used.
[How]
Replace the struct with a uint32_t
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc_link_set_backlight_level can be called from a context
where the stream is unknown. In this case, we can still
find which controller is driving this particular backlight
[How]
Compare links for equality instead of streams
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
expose dcn10_get_surface_visual_confirm_color() to be used in the
future
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A number of registers need to be updated for all active
pipes wherever any pipe causes a change in watermarks.
This change separates programming of these registers into
a separate function call that is called for all active pipes
during a bw update.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We observed an issue where a display would not accept programming of
the ignore_MSA_timing_param bit if the stream was blanked.
[How]
move enable_stream_features from enable_link_dp to
core_link_enable_stream, after unblank_stream
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some complicated blending transition cases, the head
pipe of the second stream may end up being a higher pipe
index than the free pipe. In those cases dc_add_plane_to_context
will incorrectly set the tail_pipe to the free pipe, which
will cause the top_pipe and bottom_pipe to be the same
[How]
Move the call to resource_get_tail_pipe_for_stream() to be
before call to acquire_free_pipe_for_stream().
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DPCD Extended Receiver Capability Field
[Why]
1.dpcd extended receiver capability sometimes read fail,
and corrupted data leads to sink caps is not correct.
2.sometimes sink reply ack with fewer data
[How]
check the return value of core_link_read_dpcd,
try to read again when failure happens
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
