IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The patch makes debug stats prints fw specific by adding a new member
in wmi_ops. That way it's easier to add fw_stats support to 10.4 firmware.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Tamizh Chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The Transmit Power Control (TPC) dump will show the power control values for
each rate which makes it easier to debug calibration problems.
Example usage:
# cat /sys/kernel/debug/ieee80211/phy0/ath10k/tpc_stats
TPC config for channel 5180 mode 10
CTL = 0x10 Reg. Domain = 58
Antenna Gain = 1 Reg. Max Antenna Gain = 0
Power Limit = 34 Reg. Max Power = 34
Num tx chains = 3 Num supported rates = 155
**********CDD POWER TABLE*******
No. Preamble Rate_code tpc_valu1 tpc_value2 tpc_value3
0 CCK 0x40 0 0 0
1 CCk 0x41 0 0 0
[...]
154 HTCUP 0x 0 24 0 0
**********STBC POWER TABLE******
No. Preamble Rate_code tpc_valu1 tpc_value2 tpc_value3
0 CCK 0x40 0 0 0
[...]
154 HTCUP 0x 0 24 24 0
**********TXBF POWER TABLE******
is used to dump the tx power control stats.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Copy a_sle32_to_cpu() from ath6kl so that we can easily handle signed __le32
values. This is needed in struct wmi_pdev_tpc_config_event.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During long hours of stress testing like AP interface up/down along
with continuous ping flood from a station doing connect/disconnect,
it is observed that the system is not able to allocate DMA consistent
memory of size > 512KB chunks as requested by firmware in WMI_SERVICE_EVENTID.
With the system memory getting fragmented during the run based on the
size of the memory requested, the failure to return physically continguous
memory of high order can happen. Once the system gets to this situation,
bringing up the wifi interface will fail and a system reboot may be needed
to make it work again. This problem is obseved with QCA99X0.
To fix this issue, allocate the DMA memory requested by firmware during
device probe time and keep it during the life time of the device. WMI service
ready event handler is changed to allocate the memory chunks if it is
not already allocated or if the memory allocated for the previous ready
event is not same as the current requested ones. After this patch the
memory usage when wifi is inactive will be inceased by few 100KB to
3MB based on the target type.
Failure happens with the following stack trace
[29557.488773] kworker/u4:1: page allocation failure: order:8, mode:0xd0
[29557.494297] CPU: 0 PID: 8402 Comm: kworker/u4:1 Not tainted 3.14.43 #7
[29557.500793] Workqueue: ath10k_aux_wq ath10k_wmi_event_service_ready_work [ath10k_core]
[29557.508602] [<c021e9b0>] (unwind_backtrace) from [<c021ba90>] (show_stack+0x10/0x14)
[29557.516580] [<c021ba90>] (show_stack) from [<c03bdddc>] (dump_stack+0x88/0xcc)
[29557.523612] [<c03bdddc>] (dump_stack) from [<c0290e34>] (warn_alloc_failed+0xdc/0x108)
[29557.531515] [<c0290e34>] (warn_alloc_failed) from [<c0292d88>] (__alloc_pages_nodemask+0x4f0/0x654)
[29557.540485] [<c0292d88>] (__alloc_pages_nodemask) from [<c0222b48>] (__dma_alloc_buffer.isra.20+0x2c/0x104)
[29557.550260] [<c0222b48>] (__dma_alloc_buffer.isra.20) from [<c0222c34>] (__alloc_remap_buffer.isra.23+0x14/0xb8)
[29557.560413] [<c0222c34>] (__alloc_remap_buffer.isra.23) from [<c022305c>] (__dma_alloc+0x224/0x2b8)
[29557.569490] [<c022305c>] (__dma_alloc) from [<c0223208>] (arm_dma_alloc+0x84/0x90)
[29557.577010] [<c0223208>] (arm_dma_alloc) from [<bf5159d0>] (ath10k_wmi_event_service_ready_work+0x2f8/0x420 [ath10k_core])
[29557.588055] [<bf5159d0>] (ath10k_wmi_event_service_ready_work [ath10k_core]) from [<c024260c>] (process_one_work+0x20c/0x328)
[29557.599305] [<c024260c>] (process_one_work) from [<c02432d0>] (worker_thread+0x228/0x360)
[29557.607470] [<c02432d0>] (worker_thread) from [<c0247f88>] (kthread+0xd8/0xec)
[29557.614750] [<c0247f88>] (kthread) from [<c0208d18>] (ret_from_fork+0x14/0x3c)
[29557.712751] Normal: 696*4kB (UEMR) 512*8kB (UEMR) 367*16kB (UEMR) 404*32kB (UEMR) 455*64kB (UEMR) 424*128kB (UEMR) 379*256kB (UMR) 327*512kB (UMR) 1*1024kB (R) 0*2048kB 0*4096kB = 374544kB
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Header format of 10.4 firmware phyerr event is not alligned
with pre 10.4 firmware. Introduce new wmi handlers to parse
10.4 firmware specific phyerror event header.
With changes covered in this patch, radar detection works on
qca9x0 hw 2.0 which uses 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Existing phyerr event handlers directly uses phyerr header format
(ie, struct wmi_phyerr and struct wmi_phyerr_event) in the code
exactly on how firmware packs it. This is the problem in 10.4 fw
specific phyerr event handling where it uses different phyerror
header format. Before adding 10.4 specific handler, little bit of
refactor is done in existing phyerr handlers.
Two new abstracted structures (struct wmi_phyerr_ev_hdr_arg and
struct wmi_phyerr_ev_arg) are introduced to remove dependency of using
firmware specific header format in the code. So that firmware specific
phyerror handlers can populate values to abstracted structures and
the following code can use abstracted struct for further operation.
.pull_phyerr_hdr is added newly to pull common phyerr header info
like tsf, buf_len, number of phyerr packed. Existing .pull_phyerr
handler is changed and called to parse every sub phyerrs in the event.
Validated these refactoring on qca988x hw2.0 using fw 10.2.4 version.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are three WMI_CHAN_INFO events reported per channel
in QCA99X0 firmware. First one is a notification at the begining
of the channel dwell time with cmd_flag as CHAN_INFO_START(cmd_flag = 0),
second one is a notification at the end of the dwell time with cmd_flag
CHAN_INFO_PRE_COMPLETE (cmd_flag = 2) and the third is the indication
with CHAN_INFO_COMPLETE (cmd_flag = 1) which is the last indication for
the channel. Since there is a new state before the completion, the handler
is to fixed so that the counts are deducted from the ones reported with
CHAN_INFO_START rather than the ones reported with CHAN_INFO_PRE_COMPLETE.
Without this fix there will be lots of 0 msecs reported as active
and busy time.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables MU-MIMO transmit beamforming support
for QCA99X0 chipsets.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca61x4 uses the vdev param as a sole sufficient configuration
for txbf while qca99x0 enables txbf during peer assoc by
combining the vdev param value with peer assoc's vht capabilities
This patch gets the appropriate txbf configuration scheme
before passing the wmi command to enable the same in the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 fw supports upto 4 spatial stream. Limit max spatial
stream to 4 for 10.4 firmware and to 3 for non 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Existing non 10.4 firmware scan related events and commands are
matching with 10.4 firmware (except chan info event). Link general
start scan,stop scan, scan channel list configuration functions
to 10.4 wmi function table and add a new handler to parse 10.4
specific chan info event.
10.4 firmware has extra scan completion reason
WMI_SCAN_REASON_INTERNAL_FAILURE and new scan event
WMI_SCAN_EVENT_FOREIGN_CHANNEL_EXIT compared to previous firmware
versions. These things are added in respective enum.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware swba event payload has space to accommodate upto
512 client traffic indication info & one p2p noa descriptor.
It's is not matching with exiting swba event format defined for
non 10.4 firmware. Non 10.4 firmware swba event format is designed
to support only upto only 128 client and four p2p notice of absence
descriptor.
following changes are done in this patch to enable ath10k to handle
10.4 firmware swba event,
- link generic ath10k_wmi_event_host_swba() to handle 10.4 swba
event in 10.4 wmi rx handler.
- add 10.4 specific swba event structure wmi_10_4_host_swba_event.
- new function ath10k_wmi_10_4_op_pull_swba_ev() to parse
10.4 swba event.
- increase tim_bitmap[] size in ath10k_vif to 64 to hold 512 station
power save state.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Due to 512 client support in 10.4 firmware, size of tim ie is going
to be slightly higher than non 10.4 firmware. So, size of tim_bitmap
what is carried in swba event from 10.4 firmware is bit higher.
The only bottle neck to reuse existing swba handler
ath10k_wmi_event_host_swba() for 10.4 is that code designed to deal
with fixed size tim bitmap(ie, tim_info[].tim_bitmap in wmi_swba_ev_arg).
This patch removes such size limitation and makes it more suitable
to handle swba event which has different size tim bitmap.
All existing swba event parsing functions are changed to adapt this
change. Actual support to handle 10.4 swba event is added in next patch.
Only preparation is made in this patch.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware supports upto 512 clients when qcache feature is enabled.
Make adjustment on default max peer count, active peers, number of tid in
such case to meet qcache requirement. 10.4 fw has extra unit info flag
NUM_UNITS_IS_NUM_ACTIVE_PEERS which is also handled in this patch.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware wmi mgmt rx event format differs from non 10.4
firmware and changing existing wmi mgmt rx event parsing function
ath10k_wmi_op_pull_mgmt_rx_ev() for 10.4 would add more complex.
This patch adds new function to receive any wmi rx event from
10.4 firmware and also introduce new function to parse wmi mgmt
rx event.
In addition, fw main branch service rdy event parsing function
is linked in wmi ops table.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define 10.4 wmi init command structure and introduce new function
ath10k_wmi_10_4_op_gen_init() to fill default values for each field
which goes as part of wmi init cmd to 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Include 10.4 firmware wmi pdev cmd id and prepare wmi vdev map
table wmi_10_4_pdev_param_map and update non 10.4 firmware
pdev cmd map table with newly added vdev cmd id specifically for
10.4 firmware as unsupported.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Include 10.4 firmware wmi vdev cmd id and make up wmi vdev map
table wmi_10_4_vdev_param_map and also update non 10.4 firmware
vdev cmd map table with newly added vdev cmd id specifically for
10.4 firmware as unsupported.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware wmi cmd and event id values are not exactly aligned
with previous firmware versions (main, 10.x, 10.2, etc). Add new
enum to define wmi cmd & event definitions for 10.4 firmware and
prepare wmi_10_4_cmd_map based on 10.4 firmware wmi cmd definitions.
wmi_cmd_map is extended to accommodate new wmi commands which are
exclusively available in 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Include new enum to define wmi service bitmap definitions for
10.4 firmware and a function wmi_10_4_svc_map() to remap 10.4
firmware wmi service bitmap definitions to ath10k generic wmi
services.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The macro isn't WMI specific. Instead it is
related to hardware chip so move the macro
accordingly. While at it document the magic value.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The new 10.2.4 FW support the BT-coex feature with external BT module,
The external BT modules can communicate with it via the GPIO. This patch
check the BT-coex capability of the FW and enable it by default.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the FW ATF (Air Time Fairness) service define to keep consistent
with 10.2 FW capability.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WLAN survey data provides several informative values on each channels
such as noise, active time, transmit time, and etc.
Regarding the channel activity time data, it is reported from firmware
in different form which is number of cycles instead of time itself.
Hence host driver converts it to time unit by dividing it by clock rate
that is used at baseband MAC.
Using difference clock rate from that actual HW is using will result in
inaccurate survey data. For instance, channel active time can be reported
with bigger than 150ms even though we set Dwell time to 150ms.
Therefore set the clock rate to 88000 (88 MHz) which is ath10k baseband
MAC is using.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This improves chances of getting onto a foreign
channel and thus makes P2P a bit more reliable.
Without scan burst it was possible for firmware to
not switch to foreign channel resulting in "failed
to switch to channel for roc scan" warning. This
would also effectively fail some offchan tx
requests and lead to P2P find/connect taking
longer. This could be observed when other vifs
were running/busy, e.g. with P2P GO.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This command will be used to configure
multi-channel scheduler in firmware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As a part of tdls implementation introduce
tdls related wmi data structures, constant
values and functions.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Peer type was hardcoded to default value.
For future implementation it is required
to make is configurable.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI support for WOW like enable,
wakeup events and host wakeup indication.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This can be used to implement offloaded rssi
threshold, beacon miss or even automatic
in-firmware BSS roaming in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6184 WLAN.RM.2.0-00073 has a bug in sta
powersave state machine and requires peer param to
be poked to enable the powersave.
Calling this unconditionally should be safe for
other chips/firmwares.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If firmware advertises support for TxBF then the
driver has to instruct the firmware accordingly
during runtime. Without this patch connecting to
an AP with beamformer support would yield abysmal
Rx performance.
This has been tested with wmi-tlv and qca6174
while acting as a STA beamformee only.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New qca6174 wmi-tlv firmware revisions support
more stat event bits.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable the MCS8 and MCS9 support for 2.4G band, it will
use these data rate with other devices having the same
capability.
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware revisions providing sta keepalive service
have it enabled by default.
mac80211 already does idle connection polling so
it makes no sense to duplicate this in ath10k.
mac80211 wouldn't even know of the offloaded
keepalive NullFunc frames.
This prevents sending out some extraneous frames
on the air.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New wmi-tlv firmware for qca6174 has STA keepalive
service available. The service can provide
automatic idle connection polling via NullFunc
frames to AP when acting as a client.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New wmi-tlv firmware for qca6174 supports this.
This will be used soon.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 already requests WMM per vif but firmware
wasn't able to handle this until now. However new
wmi-tlv firmware for qca6174 is capable of this.
This prepares per-vif WMM param setup.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New wmi-tlv firmware for qca6174 has u-UAPSD
autotrigger service. If it is enabled firmware
generates trigger frames automatically as
configured.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Both 10.2 firmware binaries 10.2-00082-4 and
10.2.4.20 have introduced ABI changes to fw_stats
each. This caused fw_stats to output wrong data.
Define new structures and use them to parse the
statistics correctly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will make it easier to implement fw stats
parsing for firmware 10.2.
This also renames a few structures for
consistency.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI command support for reading temperature from the target and
corresponding WMI temperature event handler. The pdev_get_temperature
command is currently supported in 10.2 firmware alone.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.2.4 firmware uses bitmask in wmi_resource_config to configure
10.2 firmware features like airtime fairness and rx batch mode instead
of maintaining separete bool entry. This allows new features that can be
configure during init time without breaking backward compatibility.
kvalo: use WMI op version, bump up FW API to 4 to not break older versions of
ath10k
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To comply with WMM-PS the device shouldn't wake up
with a NullFunc frame pair when tx-ing. Instead PM
bit on each tx frame should be used.
To make this work correctly firmware needs to be
told to use a different STA PS wake threshold when
u-APSD is enabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce a new wmi interface controls noise floor (NF) calibration
period via debugfs as firmware has introduced it on v10.2.
It allows users to modify frequency of NF calibration in millisecond
and changes RSSI reporting frequency consequently.
Short calibration period will trigger more frequent NF calibration,
so that RSSI reported in receive frames is more realistic.
Till now calibration was done at 30 seconds.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New pdev paramters have been added to firmware 10.2,
hence update wmi interfaces to sync with.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Latest main firmware branch introduced a new WMI
ABI called wmi-tlv. It is not a tlv strictly
speaking but something that resembles it because
it is ordered and may have duplicate id entries.
This prepares ath10k to support new hw.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some functions can be shared across different WMI
ABIs. Make them public so different WMI backends
can use them from different source files in the
future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the 10.x fw branch support was introduced it
became apparent ath10k will need to be able to
deal with different fw ABIs eventually.
The patch creates an abstraction for dealing with
command and event structures across different ABIs
and mostly gets rid of the
ATH10K_FW_FEATURE_WMI_10X flag usage.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
