IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Do not imply that some of the generic headers may be always included.
Instead, include explicitly what we are direct user of.
While at it, sort headers alphabetically.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Now when all MPP pins are properly defined and every MPP pin has GPIO
function, always checks for errors in armada_37xx_gpio_request_enable()
function when calling armada_37xx_pmx_set_by_name(). Function
armada_37xx_pmx_set_by_name() should not return "not supported" error
anymore for any GPIO pin when requesting GPIO mode.
Fixes: 87466ccd94 ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx")
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220805122202.23174-3-pali@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All 3 MPP pins (20, 21 and 22) can be configured individually and also can
be configured to GPIO functions. Fix definitions for these MPP pins in
existing pin groups. After this change GPIO function can be enabled just
for one of these 3 pins.
Fixes: 87466ccd94 ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220805122202.23174-2-pali@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio1_5 and gpio2_2 are GPIO-only pins. Add them into MPP groups table
so they are properly exported as valid pin numbers.
Fixes: 87466ccd94 ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220805122202.23174-1-pali@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Add PINCTRL_PINGROUP() helper macro (and use it in the AMD driver).
New drivers:
- Intel Meteor Lake support.
- Reneasas RZ/V2M and r8a779g0 (R-Car V4H).
- AXP209 variants AXP221, AXP223 and AXP809.
- Qualcomm MSM8909, PM8226, PMP8074 and SM6375.
- Allwinner D1.
Improvements:
- Proper pin multiplexing in the AMD driver.
- Mediatek MT8192 can use generic drive strength and pin
bias, then fixes on top plus some I2C pin group fixes.
- Have the Allwinner Sunplus SP7021 use the generic DT schema and
make interrupts optional.
- Handle Qualcomm SC7280 ADSP.
- Handle Qualcomm MSM8916 CAMSS GP clock muxing.
- High impedance bias on ZynqMP.
- Serialize StarFive access to MMIO.
- Immutable gpiochip for BCM2835, Ingenic, Qualcomm SPMI GPIO.
-----BEGIN PGP SIGNATURE-----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=enmk
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Outside the pinctrl driver and DT bindings we hit some Arm DT files,
patched by the maintainers.
Other than that it is business as usual.
Core changes:
- Add PINCTRL_PINGROUP() helper macro (and use it in the AMD driver).
New drivers:
- Intel Meteor Lake support.
- Reneasas RZ/V2M and r8a779g0 (R-Car V4H).
- AXP209 variants AXP221, AXP223 and AXP809.
- Qualcomm MSM8909, PM8226, PMP8074 and SM6375.
- Allwinner D1.
Improvements:
- Proper pin multiplexing in the AMD driver.
- Mediatek MT8192 can use generic drive strength and pin bias, then
fixes on top plus some I2C pin group fixes.
- Have the Allwinner Sunplus SP7021 use the generic DT schema and
make interrupts optional.
- Handle Qualcomm SC7280 ADSP.
- Handle Qualcomm MSM8916 CAMSS GP clock muxing.
- High impedance bias on ZynqMP.
- Serialize StarFive access to MMIO.
- Immutable gpiochip for BCM2835, Ingenic, Qualcomm SPMI GPIO"
* tag 'pinctrl-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (117 commits)
dt-bindings: pinctrl: qcom,pmic-gpio: add PM8226 constraints
pinctrl: qcom: Make PINCTRL_SM8450 depend on PINCTRL_MSM
pinctrl: qcom: sm8250: Fix PDC map
pinctrl: amd: Fix an unused variable
dt-bindings: pinctrl: mt8186: Add and use drive-strength-microamp
dt-bindings: pinctrl: mt8186: Add gpio-line-names property
ARM: dts: imxrt1170-pinfunc: Add pinctrl binding header
pinctrl: amd: Use unicode for debugfs output
pinctrl: amd: Fix newline declaration in debugfs output
pinctrl: at91: Fix typo 'the the' in comment
dt-bindings: pinctrl: st,stm32: Correct 'resets' property name
pinctrl: mvebu: Missing a blank line after declarations.
pinctrl: qcom: Add SM6375 TLMM driver
dt-bindings: pinctrl: Add DT schema for SM6375 TLMM
dt-bindings: pinctrl: mt8195: Use drive-strength-microamp in examples
Revert "pinctrl: qcom: spmi-gpio: make the irqchip immutable"
pinctrl: imx93: Add MODULE_DEVICE_TABLE()
pinctrl: sunxi: Add driver for Allwinner D1
pinctrl: sunxi: Make some layout parameters dynamic
pinctrl: sunxi: Refactor register/offset calculation
...
The irqchip->irq_set_type method is called by __irq_set_trigger() under
the desc->lock raw spinlock.
The armada-37xx implementation, armada_37xx_irq_set_type(), uses an MMIO
regmap created by of_syscon_register(), which uses plain spinlocks
(the kind that are sleepable on RT).
Therefore, this is an invalid locking scheme for which we get a kernel
splat stating just that ("[ BUG: Invalid wait context ]"), because the
context in which the plain spinlock may sleep is atomic due to the raw
spinlock. We need to go raw spinlocks all the way.
Make this driver create its own MMIO regmap, with use_raw_spinlock=true,
and stop relying on syscon to provide it.
This patch depends on commit 67021f25d9 ("regmap: teach regmap to use
raw spinlocks if requested in the config").
Cc: <stable@vger.kernel.org> # 5.15+
Fixes: 2f22760539 ("pinctrl: armada-37xx: Add irqchip support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220716233745.1704677-3-vladimir.oltean@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irqchip->irq_set_type method is called by __irq_set_trigger() under
the desc->lock raw spinlock.
The armada-37xx implementation, armada_37xx_irq_set_type(), takes a
plain spinlock, the kind that becomes sleepable on RT.
Therefore, this is an invalid locking scheme for which we get a kernel
splat stating just that ("[ BUG: Invalid wait context ]"), because the
context in which the plain spinlock may sleep is atomic due to the raw
spinlock. We need to go raw spinlocks all the way.
Replace the driver's irq_lock with a raw spinlock, to disable preemption
even on RT.
Cc: <stable@vger.kernel.org> # 5.15+
Fixes: 2f22760539 ("pinctrl: armada-37xx: Add irqchip support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220716233745.1704677-2-vladimir.oltean@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Introduce helpers to iterate over GPIO chip nodes and covert some drivers
The following is an automated git shortlog grouped by driver:
gpiolib:
- Introduce a helper to get first GPIO controller node
- Introduce gpiochip_node_count() helper
- Introduce for_each_gpiochip_node() loop helper
pinctrl:
- meson: Replace custom code by gpiochip_node_count() call
- meson: Enable COMPILE_TEST
- meson: Rename REG_* to MESON_REG_*
- armada-37xx: Reuse GPIO fwnode in armada_37xx_irqchip_register()
- armada-37xx: Switch to use fwnode instead of of_node
- samsung: Switch to use for_each_gpiochip_node() helper
- samsung: Drop redundant node parameter in samsung_banks_of_node_get()
- npcm7xx: Switch to use for_each_gpiochip_node() helper
- renesas: rza1: Switch to use for_each_gpiochip_node() helper
- renesas: rza1: Replace custom code by gpiochip_node_count() call
- stm32: Switch to use for_each_gpiochip_node() helper
- stm32: Replace custom code by gpiochip_node_count() call
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSu93Raj3rZDNXzGZv7cr9lmVa5zAUCYmwsmgAKCRD7cr9lmVa5
zEYPAP4q31AbTJHk6Fs1A79esVSo+DZSkZSzbk/n8Vr3oYG56gD/dVu5EmLNKPHU
6o5+BvdXqjHrymihHasdyD9YqI30zwM=
=MIEU
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel
intel-gpio for v5.19-1
* Introduce helpers to iterate over GPIO chip nodes and covert some drivers
The following is an automated git shortlog grouped by driver:
gpiolib:
- Introduce a helper to get first GPIO controller node
- Introduce gpiochip_node_count() helper
- Introduce for_each_gpiochip_node() loop helper
pinctrl:
- meson: Replace custom code by gpiochip_node_count() call
- meson: Enable COMPILE_TEST
- meson: Rename REG_* to MESON_REG_*
- armada-37xx: Reuse GPIO fwnode in armada_37xx_irqchip_register()
- armada-37xx: Switch to use fwnode instead of of_node
- samsung: Switch to use for_each_gpiochip_node() helper
- samsung: Drop redundant node parameter in samsung_banks_of_node_get()
- npcm7xx: Switch to use for_each_gpiochip_node() helper
- renesas: rza1: Switch to use for_each_gpiochip_node() helper
- renesas: rza1: Replace custom code by gpiochip_node_count() call
- stm32: Switch to use for_each_gpiochip_node() helper
- stm32: Replace custom code by gpiochip_node_count() call
Since we have fwnode of the first found GPIO controller assigned to the
struct gpio_chip, we may reuse it in the armada_37xx_irqchip_register().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This pinctrl driver supports the 98DX25xx and 98DX35xx family of chips
from Marvell. It is based on the Marvell SDK with additions for various
(non-gpio) pin configurations based on the datasheet.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220414233055.586962-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we have a generic helper, switch the module to use it.
As a side effect, add check for the memory allocation failures and
cleanup it either in error case or when driver is unloading.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
It's fine to call dev_err_probe() in ->probe() when error code is known.
Convert the driver to use dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Use the devm_platform_ioremap_resource() helper instead of
calling of_address_to_resource() and devm_ioremap_resource()
separately.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Use temporary variable for struct device to make code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Kernel doc validator is not happy:
.../pinctrl-armada-37xx.c:926: warning: expecting prototype for armada_37xx_fill_funcs(). Prototype was for armada_37xx_fill_func() instead
Fix this by updating function name in the kernel doc.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The PWM pins on North Bridge on Armada 37xx can be configured into PWM
or GPIO functions. When in PWM function, each pin can also be configured
to drive low on 0 and tri-state on 1 (LED mode).
The current definitions handle this by declaring two pin groups for each
pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"
This is semantically incorrect. The correct definition for each pin
should be one group with three functions: "pwm", "led" and "gpio".
Change the "pwmN" groups to support "led" function.
Remove "ledN_od" groups. This cannot break backwards compatibility with
older device trees: no device tree uses it since there is no PWM driver
for this SOC yet. Also "ledN_od" groups are not even documented.
Fixes: b835d69530 ("pinctrl: armada-37xx: swap polarity on LED group")
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210719112938.27594-1-kabel@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function name is used for selecting MPP functionality and
should be unique within function names of the same pin.
This patch fixes function names for MPP54 and MPP55 that
have two different functions named the same.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20210216113118.17484-3-kostap@marvell.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove all empty lines at the end of functions in pinctrl subsystem,
and make the code neat.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Zhaoyu Liu <zackaryliu@yeah.net>
Link: https://lore.kernel.org/r/X98NP6NFK1Afzrgd@manjaro
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- NONE whatsoever, we don't even touch the core files this
time around.
New drivers:
- New driver for the Toshiba Visconti SoC.
- New subdriver for the Qualcomm MSM8226 SoC.
- New subdriver for the Actions Semiconductor S500 SoC.
- New subdriver for the Mediatek MT8192 SoC.
- New subdriver for the Microchip SAMA7G5 SoC.
Driver enhancements:
- Intel Cherryview and Baytrail cleanups and refactorings.
- Enhanced support for the Renesas R8A7790, more pins and
groups.
- Some optimizations for the MCP23S08 MCP23x17 variant.
- Some cleanups around the Actions Semiconductor subdrivers.
- A bunch of cleanups around the SH-PFC and Emma Mobile
drivers.
- The "SH-PFC" (literally SuperH pin function controller, I
think) subdirectory is now renamed to the more neutral
"renesas", as these are not very much centered around
SuperH anymore.
- Non-critical fixes for the Aspeed driver.
- Non-critical fixes for the Ingenic (MIPS!) driver.
- Fix a bunch of missing pins on the AMD pinctrl driver.
-----BEGIN PGP SIGNATURE-----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=TdjX
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Core changes:
- NONE whatsoever, we don't even touch the core files this time
around.
New drivers:
- New driver for the Toshiba Visconti SoC.
- New subdriver for the Qualcomm MSM8226 SoC.
- New subdriver for the Actions Semiconductor S500 SoC.
- New subdriver for the Mediatek MT8192 SoC.
- New subdriver for the Microchip SAMA7G5 SoC.
Driver enhancements:
- Intel Cherryview and Baytrail cleanups and refactorings.
- Enhanced support for the Renesas R8A7790, more pins and groups.
- Some optimizations for the MCP23S08 MCP23x17 variant.
- Some cleanups around the Actions Semiconductor subdrivers.
- A bunch of cleanups around the SH-PFC and Emma Mobile drivers.
- The "SH-PFC" (literally SuperH pin function controller, I think)
subdirectory is now renamed to the more neutral "renesas", as these
are not very much centered around SuperH anymore.
- Non-critical fixes for the Aspeed driver.
- Non-critical fixes for the Ingenic (MIPS!) driver.
- Fix a bunch of missing pins on the AMD pinctrl driver"
* tag 'pinctrl-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (78 commits)
pinctrl: amd: Add missing pins to the pin group list
dt-bindings: pinctrl: sunxi: Allow pinctrl with more interrupt banks
pinctrl: visconti: PINCTRL_TMPV7700 should depend on ARCH_VISCONTI
pinctrl: mediatek: Free eint data on failure
pinctrl: single: fix debug output when #pinctrl-cells = 2
pinctrl: single: fix pinctrl_spec.args_count bounds check
pinctrl: sunrisepoint: Modify COMMUNITY macros to be consistent
pinctrl: cannonlake: Modify COMMUNITY macros to be consistent
pinctrl: tigerlake: Fix register offsets for TGL-H variant
pinctrl: Document pinctrl-single,pins when #pinctrl-cells = 2
pinctrl: mediatek: use devm_platform_ioremap_resource_byname()
pinctrl: nuvoton: npcm7xx: Constify static ops structs
pinctrl: mediatek: mt7622: add antsel pins/groups
pinctrl: ocelot: simplify the return expression of ocelot_gpiochip_register()
pinctrl: at91-pio4: add support for sama7g5 SoC
dt-bindings: pinctrl: at91-pio4: add microchip,sama7g5
pinctrl: spear: simplify the return expression of tvc_connect()
pinctrl: spear: simplify the return expression of spear310_pinctrl_probe
pinctrl: sprd: use module_platform_driver to simplify the code
pinctrl: Ingenic: Add I2S pins support for Ingenic SoCs.
...
Per the datasheet the i2c functions use MPP_Sel=0x1. They are documented
as using MPP_Sel=0x4 as well but mixing 0x1 and 0x4 is clearly wrong. On
the board tested 0x4 resulted in a non-functioning i2c bus so stick with
0x1 which works.
Fixes: d7ae8f8dee ("pinctrl: mvebu: pinctrl driver for 98DX3236 SoC")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20200907211712.9697-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Group name 'pcie1' is misleading as it controls only PCIe reset pin. Like
other PCIe groups it should have been called 'pcie1_reset'. But due to
backward compatibility it is not possible to change existing group name.
So just add comment describing this PCIe reset functionality.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200724132457.7094-1-pali@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Correct misspellings and provide missing entries.
Fixes the following W=1 kernel build warning(s):
drivers/pinctrl/mvebu/pinctrl-armada-37xx.c:68: warning: Function parameter or member 'start_pin' not described in 'armada_37xx_pin_group'
drivers/pinctrl/mvebu/pinctrl-armada-37xx.c:68: warning: Function parameter or member 'val' not described in 'armada_37xx_pin_group'
drivers/pinctrl/mvebu/pinctrl-armada-37xx.c:68: warning: Function parameter or member 'extra_pin' not described in 'armada_37xx_pin_group'
drivers/pinctrl/mvebu/pinctrl-armada-37xx.c:68: warning: Function parameter or member 'extra_npins' not described in 'armada_37xx_pin_group'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lore.kernel.org/r/20200713144930.1034632-25-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use newly added GPIO defines GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT instead of using hard-coded 1 and 0.
Main benefit is to make it easier to see which values mean IN and which
OUT. As a side effect this helps GPIO framework to change the direction
defines to something else if ever needed.
Please note that return value from get_direction call on
pinctrl-axp209 driver was changed. Previously pinctrl-axp209 might have
returned value 2 for direction INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Link: https://lore.kernel.org/r/20200214135712.GA14557@localhost.localdomain
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_irq_count() and platform_get_irq() is the more generic
way (independent of device trees) to determine the count of available
interrupts. So use this instead.
As platform_irq_count() might return an error code (which
of_irq_count doesn't) some additional handling is necessary.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1576672860-14420-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/1574306382-32516-1-git-send-email-krzk@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As explained in the following commit a9a1a48336 ("pinctrl:
armada-37xx: Fix gpio interrupt setup") the armada_37xx_irq_set_type()
function can be called before the initialization of the mask field.
That means that we can't use this field in this function and need to
workaround it using hwirq.
Fixes: 30ac0d3b07 ("pinctrl: armada-37xx: Add edge both type gpio irq support")
Cc: stable@vger.kernel.org
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191115155752.2562-1-gregory.clement@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191002121550.16104-1-linus.walleij@linaro.org
The configuration registers for the LED group have inverted
polarity, which puts the GPIO into open-drain state when used in
GPIO mode. Switch to '0' for GPIO and '1' for LED modes.
Fixes: 87466ccd94 ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx")
Signed-off-by: Patrick Williams <alpawi@amazon.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191001155154.99710-1-alpawi@amazon.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 37xx configuration registers are only 32 bits long, so
pins 32-35 spill over into the next register. The calculation
for the register address was done, but the bitmask was not, so
any configuration to pin 32 or above resulted in a bitmask that
overflowed and performed no action.
Fix the register / offset calculation to also adjust the offset.
Fixes: 5715092a45 ("pinctrl: armada-37xx: Add gpio support")
Signed-off-by: Patrick Williams <alpawi@amazon.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191001154634.96165-1-alpawi@amazon.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With CP115 standalone modules, all MPP configuration are
possible. Handle this new possibility thanks to the new
"marvell,cp115-standalone-pinctrl" compatible property.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[<miquel.raynal@bootlin.com>: mention the new compatible in the
commit log]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20190805101607.29811-4-miquel.raynal@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add missing definition for function 0xe on CP-110 MPP-62.
The pin function is Data Strobe for SDIO interface.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20190805101607.29811-2-miquel.raynal@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
The 98DX1135 is a switch chip with an integrated CPU. This is similar to
the 98DX4122 except the MPP assignments differ.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Armada 3700 PCIe IP relies on the pinctrl IP managed by this
driver. For reasons related to the PCI core's organization when
suspending/resuming, PCI host controller drivers must reconfigure
their register at suspend_noirq()/resume_noirq() which happens after
suspend()/suspend_late() and before resume_early()/resume().
In the current state, after resuming from a suspend to RAM cycle the
PCIe IP is reconfigured before the pinctrl one which produces an
interrupt storm. The solution to support PCIe resume operation is to
change the "priority" of this pinctrl driver PM callbacks to
"_noirq()".
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a cleanup and fix of the patch by Ken Ma <make@marvell.com>.
Fix the mpp definitions according to newest revision of the
specification:
- northbridge:
fix pmic1 gpio number to 7
fix pmic0 gpio number to 6
- southbridge
split pcie1 group bit mask to BIT(5) and BIT(9)
fix ptp group bit mask to BIT(11) | BIT(12) | BIT(13)
add smi group with bit mask BIT(4)
[gregory: split the pcie group in 2, as at hardware level they can be
configured separately]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These drivers are GPIO drivers, and the do not need to use the
legacy header in <linux/gpio.h>, go directly for
<linux/gpio/driver.h> instead.
Replace any use of GPIOF_* with 0/1, these flags are for
consumers, not drivers.
Get rid of a few gpio_to_irq() users that was littering
around the place, use local callbacks or avoid using it at
all.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add suspend/resume hooks in pinctrl driver to handle S2RAM operations.
Beyond the traditional register save/restore operations, these hooks
also keep the GPIOs used for both-edge IRQ synchronized between their
level (low/high) and expected IRQ polarity (falling/rising edge).
Since pinctrl is an infrastructure module, its resume should be issued
prior to other IO drivers. The pinctrl PM operations are requested at
early/late stages for this reason.
Suggested-by: Ken Ma <make@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
