IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Configure MT_VHT_HT_FBK_CFG1 values similar like vendor driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure protection based on information that are provided to
us either by remote AP or by hostapd via HT operation IE.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On new mt76 chips, phy mode is configured by last 3 bits
of rate value. Hence OFDM bit is marked by 0x2000
instead of 0x4000.
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use set_rts_threshold calback to enable/disable threshold only for
legacy traffic.
Protection for HT and VHT traffic is defined by HT operation element
and it's provided by remote AP or by hostapd.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As already done for pcie code in commit 79d1c94c9c78 ("mt76: avoid
queue/status spinlocks while passing tx status to mac80211") make sure
that no tx related spinlocks are taken during the ieee80211_tx_status call
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Grab mt76_dev mutex in mt76x02_mac_work handler since it runs
concurrently with mt76x{0,2}_set_channel routines
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reconfigure properly MT_MAC_SYS_CTRL register after mac sw-reset
in mt76x02_check_mac_err routine
Fixes: 73556561ab9f ("mt76x0: use mt76x02_mac_work as stats handler")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MODULE_FIRMWARE() is used in usb_mcu.c and provided by linux/module.h,
but this header file is not directly included. This causes problems in
backports with some kernel versions.
Add the missing include.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Precompute data length in order to avoid to allocate the related
skb data structure if reported length does not fit in queue buf_size
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove napi from mt76_dma_rx_fill routine signature since
it is a leftover of a previous implementation and it is no
longer used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
So far the code only validates the buffer size of the first skb.
Extend this check to cover additional fragments as well, in case the size
is corrupted during a DMA reset.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcG9TEAAoJEG4XJFUm622byW8H/1vMVJhXwgIZbHeoUKNa47Yp
Z7Jv5vW8IGXu+lp7DyoedDCbq4+lskNSlDV1DmysNChLgDnApU/3oCd/jH8EiGPV
JAFUHb85HuVLTTpPpNHtnYz3IzL7r098TNVxOU0VD+xILM0Mf0aCeXztgmFWpGaY
/rfHkId8oKUezIjdu6Dc96mqITrT6WRNtnOMfjr6dZPjClRTS44Hyz3Ga3rXABBL
/n8BCkl0GpKGrL3mBy2CCR5mVY8zfxMB4Aj2zx7bccZ8i2i2QjrGlXCHyB6ImNrR
lv4L1fUVXZWVdeOe8EbpftY7zEsPrX+XNm6h1kckdB7UyuBROpQLsVb+yxlLh9g=
=mhAw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from mac80211 commit adf8ed01e4fd ("mac80211: add an optional
TXQ for other PS-buffered frames") and commit 0eeb2b674f05 ("mac80211:
add an option for station management TXQ") a new per-sta queue has been
introduced for bufferable management frames.
sta->txq[IEEE80211_NUM_TIDS] is initialized just if the driver reports
the following hw flags:
- IEEE80211_HW_STA_MMPDU_TXQ
- IEEE80211_HW_BUFF_MMPDU_TXQ
This can produce a NULL pointer dereference in mt76_stop_tx_queues
since mt76 iterates on all available sta tx queues assuming they are
initialized by mac80211. This issue has been spotted analyzing the code
(it has not triggered any crash yet)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* use the same firmware for mt76x2e and mt76x2u
* mt76x2 fixes
* mt76x0 fixes
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG/MacGPG2 v2
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAlwBH4oACgkQ130UHQKnbvUdQwCdFL9rDWnaX1nvSwLZrp3DC7qD
CywAoJaygMHs0YVmXWHQ9tdEAY5i4VAO
=qF8w
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2018-11-30' of https://github.com/nbd168/wireless
first batch of mt76 patches for 4.21
* use the same firmware for mt76x2e and mt76x2u
* mt76x2 fixes
* mt76x0 fixes
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
kvalo: fixed a conflict in drivers/net/wireless/mediatek/mt76/mt76x2/pci_main.c
and a build problem in drivers/net/wireless/mediatek/mt76/mt76x02_util.c
Allows adding unassociated stations from mac80211
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
If there are still pending packets in the tx queue when removing a station,
it could possibly lead to a call to further attempts to pull packets from
the mac80211 tx queue after it has already been removed from the scheduling
list.
Prevent this from happening by calling synchronize_rcu after deleting the
wcid pointer before further cleaning up the tx queues.
To be extra careful, ensure that mtxq->list is always initialized properly.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is some code in the mac80211 tx status processing code that could
potentially call back into the tx codepath.
To avoid deadlocks, make sure that no tx related spinlocks are taken
during the ieee80211_tx_status call.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We always wait for CMD_CALIBRATION_OP mcu message, but wait argument is used
for do additional MT_MCU_COM_REG0 register operations, which are needed
for mt76x2e devices and we can use appropriate check instead of wait argument.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x2u_init_beacon_offsets routine since the driver supports
just STA mode
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize bss_info_changed mac80211 callback to
mt76x02_bss_info_changed utility routine and remove duplicated code.
Use 8 as WCID index for sta interface
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Perform channel calibration after each channel switch and not only after
connection establishment since NetworkManager perform multiple frequency
scanning if RSSI in lower a given threshold
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add MCU_CAL_TX_SHAPING calibration in mt76x2u_phy_channel_calibrate
routine since now mt76x2 and mt76x2u driver run the same firmware
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable VHT tx rates in ad-hoc mode for mt76x0e driver.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x02_config_mac_addr_list routine in order to set
the mac address list supported by the driver. Initialize
wiphy->addresses/n_addresses for mt76x0e driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix IBI_R11 configuration on non-radar channels for mt76x0e
driver. This patch improve system stability under heavy load.
Moreover use IBI_R11 name and remove magic numbers for
0x212c register
Fixes: 0c3b3abc9251 ("mt76x0: pci: add DFS support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Assure that after we initialize dev->cal.low_gain to -1 this
will cause update gain calibration. Otherwise this might or
might not happen depending on value of second bit of low_gain
and values read from registers in mt76x02_phy_adjust_vga_gain().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If we are associated and scanning is performed, sw_scan_complete callback
is done after we get back to operating channel, so we do not perform
queue cal work. Fix this queue cal work from sw_scan_complete().
On mt76x0 we have to restore gain in MT_BBP(AGC, 8) register after
scanning, as it was multiple times modified by channel switch code.
So queue cal work without any delay to set AGC gain value.
Similar like in mt76x2 init AGC gain only when set operating channel
and just check before queuing cal work in sw_scan_complete() if
initialization was already done.
Fixes: bbd10586f0df ("mt76x0: phy: do not run calibration during channel switch")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove wait argument from mt76x02_mcu_set_radio_state and newer wait
for response when sending CMD_POWER_SAVING_OP mcu command.
Note this change behaviour for PCIe devices, but the change is in
align with vendor driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove wait argument from mt76x02_mcu_function_select and wait for
response when function is not Q_SELECT, what is the same behaviour
like in vendor driver.
Note this change behaviour for PCIe devices for Q_SELECT function
form wait to no-wait, and for mt76x0u BW_SETTING from no-wait to wait.
But the change is in align with vendor driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We almost always use patter like this:
skb = mt76_mcu_msg_alloc(dev, &msg, sizeof(msg));
return mt76_mcu_send_msg(dev, skb, CMD_FUN_SET_OP, wait_resp);
This is not needed, we can allocate skb in mcu_send_msg routine.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We use always 1 as band parameter for MCU_CAL_LC, this break 2GHz,
we should use 0 for this band instead.
Patch fixes problems happened sometimes when try to associate with 2GHz
AP and manifest by errors like below:
[14680.920823] wlan0: authenticate with 18:31:bf:c0:51:b0
[14681.109506] wlan0: send auth to 18:31:bf:c0:51:b0 (try 1/3)
[14681.310454] wlan0: send auth to 18:31:bf:c0:51:b0 (try 2/3)
[14681.518469] wlan0: send auth to 18:31:bf:c0:51:b0 (try 3/3)
[14681.726499] wlan0: authentication with 18:31:bf:c0:51:b0 timed out
Fixes: 9aec146d0f6b ("mt76x0: pci: introduce mt76x0_phy_calirate routine")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use tssi calibrated value to configure tx power gain if tssi is enabled
in eeprom data
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run mt76x0 tssi calibration process if enabled in eeprom data.
Perform calibration procedure every 4s
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_eeprom_copy utility routine in mt76x02-lib module
in order to be reused by mt76x0 driver adding tssi calibration
support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_mac_wcid_setup and mt76x02_mac_shared_key_setup for
shared keys and wcid table initialization and remove duplicated
code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove MT_TSO_CTRL and MT_HEADER_TRANS_CTRL_REG initialization since
it is already done in mt76_write_mac_initvals routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_mac_wcid_setup utility routine for wcid init configuration
and remove duplicated code. This patch fixes a mt76x0 AP issue since
hw key table selection was set to pairwise by default
Fixes: dbad2adcb2c7 ("mt76x0: pci: enable AP support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move WCID tx rate configuration at device bootstrap since
the related register are always set to 0
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_mac_shared_key_setup utility routine for shared key
initialization and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76_poll_msec utility routine for CORE_R34 register polling
instead of mt76_poll in order to allow the hw to complete requested
calibration since on slow devices (e.g. mt7620 based boards) calibration
takes longer than 2ms
Fixes: 66a34c66e0cb ("mt76x0: phy: add phy/vco temperature compensation")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT_BBP(AGC, 8) register has values depend on band in
mt76x0_bbp_switch_tab, so we should not overwrite other fields
than MT_BBP_AGC_GAIN when setting gain.
This can fix performance issues when connecting to 2.4GHz AP.
Fixes: 4636a2544c3b ("mt76x0: phy: align channel gain logic to mt76x2 one")
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT76x2/MT76x0 has somewhat unreliable tx status reporting, and for that
reason the driver currently does not report per-skb tx ack status at all.
This breaks things like client idle polling, which relies on the tx ack
status of a transmitted nullfunc frame.
This patch adds code to report skb-attached tx status if requested by
mac80211 or the rate control module. Since tx status is polled from a
simple FIFO register, the code needs to account for the possibility of
tx status events getting lost.
The code keeps a list of skbs for which tx status is required and passes
them to mac80211 once tx status has been filled in and the DMA queue is
done with it.
If a tx status event is not received after one second, the status rates
are cleared, and a succesful ACK is indicated to avoid spurious disassoc
during assoc or client polling.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
control->sta is set to NULL early when encryption is turned on for the
station and info->control.hw_key is not set.
This code is missing a check for the 802.11 header protected flag, otherwise
it resets the station for other frames, e.g. client probing frames.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
