IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
otherwise the synopsys_id value may be read out wrong,
because the GMAC_VERSION register might still be in reset
state, for at least 1 us after the reset is de-asserted.
Add a wait for 10 us before continuing to be on the safe side.
> From what have you got that delay value?
Just try and error, with very old linux versions and old gcc versions
the synopsys_id was read out correctly most of the time (but not always),
with recent linux versions and recnet gcc versions it was read out
wrongly most of the time, but again not always.
I don't have access to the VHDL code in question, so I cannot
tell why it takes so long to get the correct values, I also do not
have more than a few hardware samples, so I cannot tell how long
this timeout must be in worst case.
Experimentally I can tell that the register is read several times
as zero immediately after the reset is de-asserted, also adding several
no-ops is not enough, adding a printk is enough, also udelay(1) seems to
be enough but I tried that not very often, and I have not access to many
hardware samples to be 100% sure about the necessary delay.
And since the udelay here is only executed once per device instance,
it seems acceptable to delay the boot for 10 us.
BTW: my hardware's synopsys id is 0x37.
Fixes: c5e4ddbdfa11 ("net: stmmac: Add support for optional reset control")
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/AS8P193MB1285A810BD78C111E7F6AA34E4752@AS8P193MB1285.EURP193.PROD.OUTLOOK.COM
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some DSA tagging protocols change the EtherType field in the MAC header
e.g. DSA_TAG_PROTO_(DSA/EDSA/BRCM/MTK/RTL4C_A/SJA1105). On TX these tagged
frames are ignored by the checksum offload engine and IP header checker of
some stmmac cores.
On RX, the stmmac driver wrongly assumes that checksums have been computed
for these tagged packets, and sets CHECKSUM_UNNECESSARY.
Add an additional check in the stmmac TX and RX hotpaths so that COE is
deactivated for packets with ethertypes that will not trigger the COE and
IP header checks.
Fixes: 6b2c6e4a938f ("net: stmmac: propagate feature flags to vlan")
Cc: <stable@vger.kernel.org>
Reported-by: Richard Tresidder <rtresidd@electromag.com.au>
Link: https://lore.kernel.org/netdev/e5c6c75f-2dfa-4e50-a1fb-6bf4cdb617c2@electromag.com.au/
Reported-by: Romain Gantois <romain.gantois@bootlin.com>
Link: https://lore.kernel.org/netdev/c57283ed-6b9b-b0e6-ee12-5655c1c54495@bootlin.com/
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found the following dmesg calltrace when testing the GMAC NIC notebook:
[9.448656] ------------[ cut here ]------------
[9.448658] Unbalanced IRQ 43 wake disable
[9.448673] WARNING: CPU: 3 PID: 1083 at kernel/irq/manage.c:688 irq_set_irq_wake+0xe0/0x128
[9.448717] CPU: 3 PID: 1083 Comm: ethtool Tainted: G O 4.19 #1
[9.448773] ...
[9.448774] Call Trace:
[9.448781] [<9000000000209b5c>] show_stack+0x34/0x140
[9.448788] [<9000000000d52700>] dump_stack+0x98/0xd0
[9.448794] [<9000000000228610>] __warn+0xa8/0x120
[9.448797] [<9000000000d2fb60>] report_bug+0x98/0x130
[9.448800] [<900000000020a418>] do_bp+0x248/0x2f0
[9.448805] [<90000000002035f4>] handle_bp_int+0x4c/0x78
[9.448808] [<900000000029ea40>] irq_set_irq_wake+0xe0/0x128
[9.448813] [<9000000000a96a7c>] stmmac_set_wol+0x134/0x150
[9.448819] [<9000000000be6ed0>] dev_ethtool+0x1368/0x2440
[9.448824] [<9000000000c08350>] dev_ioctl+0x1f8/0x3e0
[9.448827] [<9000000000bb2a34>] sock_ioctl+0x2a4/0x450
[9.448832] [<900000000046f044>] do_vfs_ioctl+0xa4/0x738
[9.448834] [<900000000046f778>] ksys_ioctl+0xa0/0xe8
[9.448837] [<900000000046f7d8>] sys_ioctl+0x18/0x28
[9.448840] [<9000000000211ab4>] syscall_common+0x20/0x34
[9.448842] ---[ end trace 40c18d9aec863c3e ]---
Multiple disable_irq_wake() calls will keep decreasing the IRQ
wake_depth, When wake_depth is 0, calling disable_irq_wake() again,
will report the above calltrace.
Due to the need to appear in pairs, we cannot call disable_irq_wake()
without calling enable_irq_wake(). Fix this by making sure there are
no unbalanced disable_irq_wake() calls.
Fixes: 3172d3afa998 ("stmmac: support wake up irq from external sources (v3)")
Signed-off-by: Qiang Ma <maqianga@uniontech.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240112021249.24598-1-maqianga@uniontech.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently get/set_link_ksettings ethtool ops are dependent on PCS.
When PCS is integrated, it will not have separate link config.
Bypass configuring and checking PCS for integrated PCS.
Fixes: aa571b6275fb ("net: stmmac: add new switch to struct plat_stmmacenet_data")
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Sneh Shah <quic_snehshah@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert "net: stmmac: Use interrupt mode INTM=1 for per channel irq"
This reverts commit 36af9f25ddfd311da82628f194c794786467cb12.
Revert "net: stmmac: Add support for TX/RX channel interrupt"
This reverts commit 9072e03d32088137a435ddf3aa95fd6e038d69d8.
Revert "net: stmmac: Make MSI interrupt routine generic"
This reverts commit 477bd4beb93bf9ace9bda71f1437b191befa9cf4.
Revert "dt-bindings: net: snps,dwmac: per channel irq"
This reverts commit 67d47c8ada0f8795bfcdb85cc8f2ad3ce556674b.
Device tree bindings need to be reviewed.
Link: https://lore.kernel.org/all/2df9fe3e-7971-4aa2-89a9-0e085b3b00d7@linaro.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable per DMA channel interrupt that uses shared peripheral
interrupt (SPI), so only per channel TX and RX intr (TI/RI)
are handled by TX/RX ISR without calling common interrupt ISR.
Signed-off-by: Teoh Ji Sheng <ji.sheng.teoh@intel.com>
Signed-off-by: Swee Leong Ching <leong.ching.swee@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no support for per DMA channel interrupt for non-MSI platform,
where the MAC's per channel interrupt hooks up to interrupt controller(GIC)
through shared peripheral interrupt(SPI) to handle interrupt from TX/RX
transmit channel.
This patch generalize the existing MSI ISR to also support non-MSI
platform.
Signed-off-by: Teoh Ji Sheng <ji.sheng.teoh@intel.com>
Signed-off-by: Swee Leong Ching <leong.ching.swee@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix per-queue statistics for devices with more than one queue.
The output data pointer is currently reset in each loop iteration,
effectively summing all queue statistics in the first four u64 values.
The summary values are not even labeled correctly. For example, if eth0 has
2 queues, ethtool -S eth0 shows:
q0_tx_pkt_n: 374 (actually tx_pkt_n over all queues)
q0_tx_irq_n: 23 (actually tx_normal_irq_n over all queues)
q1_tx_pkt_n: 462 (actually rx_pkt_n over all queues)
q1_tx_irq_n: 446 (actually rx_normal_irq_n over all queues)
q0_rx_pkt_n: 0
q0_rx_irq_n: 0
q1_rx_pkt_n: 0
q1_rx_irq_n: 0
Fixes: 133466c3bbe1 ("net: stmmac: use per-queue 64 bit statistics where necessary")
Cc: stable@vger.kernel.org
Signed-off-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver should continue get the timestamp if STMMAC_FLAG_EXT_SNAPSHOT_EN
flag is set.
Fixes: aa5513f5d95f ("net: stmmac: replace the ext_snapshot_en field with a flag")
Cc: <stable@vger.kernel.org> # 6.6
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Lai Peter Jun Ann <jun.ann.lai@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a MDIO bus is created if the devicetree description is either:
1. Not fixed-link
2. fixed-link but contains a MDIO bus as well
The "1" case above isn't always accurate. If there's a phy-handle,
it could be referencing a phy on another MDIO controller's bus[1]. In
this case, where the MDIO bus is not described at all, currently
stmmac will make a MDIO bus and scan its address space to discover
phys (of which there are none). This process takes time scanning a bus
that is known to be empty, delaying time to complete probe.
There are also a lot of upstream devicetrees[2] that expect a MDIO bus
to be created, scanned for phys, and the first one found connected
to the MAC. This case can be inferred from the platform description by
not having a phy-handle && not being fixed-link. This hits case "1" in
the current driver's logic, and must be handled in any logic change here
since it is a valid legacy dt-binding.
Let's improve the logic to create a MDIO bus if either:
- Devicetree contains a MDIO bus
- !fixed-link && !phy-handle (legacy handling)
This way the case where no MDIO bus should be made is handled, as well
as retaining backwards compatibility with the valid cases.
Below devicetree snippets can be found that explain some of
the cases above more concretely.
Here's[0] a devicetree example where the MAC is both fixed-link and
driving a switch on MDIO (case "2" above). This needs a MDIO bus to
be created:
&fec1 {
phy-mode = "rmii";
fixed-link {
speed = <100>;
full-duplex;
};
mdio1: mdio {
switch0: switch0@0 {
compatible = "marvell,mv88e6190";
pinctrl-0 = <&pinctrl_gpio_switch0>;
};
};
};
Here's[1] an example where there is no MDIO bus or fixed-link for
the ethernet1 MAC, so no MDIO bus should be created since ethernet0
is the MDIO master for ethernet1's phy:
ðernet0 {
phy-mode = "sgmii";
phy-handle = <&sgmii_phy0>;
mdio {
compatible = "snps,dwmac-mdio";
sgmii_phy0: phy@8 {
compatible = "ethernet-phy-id0141.0dd4";
reg = <0x8>;
device_type = "ethernet-phy";
};
sgmii_phy1: phy@a {
compatible = "ethernet-phy-id0141.0dd4";
reg = <0xa>;
device_type = "ethernet-phy";
};
};
};
ðernet1 {
phy-mode = "sgmii";
phy-handle = <&sgmii_phy1>;
};
Finally there's descriptions like this[2] which don't describe the
MDIO bus but expect it to be created and the whole address space
scanned for a phy since there's no phy-handle or fixed-link described:
&gmac {
phy-supply = <&vcc_lan>;
phy-mode = "rmii";
snps,reset-gpio = <&gpio3 RK_PB4 GPIO_ACTIVE_HIGH>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 1000000>;
};
[0] https://elixir.bootlin.com/linux/v6.5-rc5/source/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts
[1] https://elixir.bootlin.com/linux/v6.6-rc5/source/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
[2] https://elixir.bootlin.com/linux/v6.6-rc5/source/arch/arm64/boot/dts/rockchip/rk3368-r88.dts#L164
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Co-developed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/intel/iavf/iavf_ethtool.c
3a0b5a2929fd ("iavf: Introduce new state machines for flow director")
95260816b489 ("iavf: use iavf_schedule_aq_request() helper")
https://lore.kernel.org/all/84e12519-04dc-bd80-bc34-8cf50d7898ce@intel.com/
drivers/net/ethernet/broadcom/bnxt/bnxt.c
c13e268c0768 ("bnxt_en: Fix HWTSTAMP_FILTER_ALL packet timestamp logic")
c2f8063309da ("bnxt_en: Refactor RX VLAN acceleration logic.")
a7445d69809f ("bnxt_en: Add support for new RX and TPA_START completion types for P7")
1c7fd6ee2fe4 ("bnxt_en: Rename some macros for the P5 chips")
https://lore.kernel.org/all/20231211110022.27926ad9@canb.auug.org.au/
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c
bd6781c18cb5 ("bnxt_en: Fix wrong return value check in bnxt_close_nic()")
84793a499578 ("bnxt_en: Skip nic close/open when configuring tstamp filters")
https://lore.kernel.org/all/20231214113041.3a0c003c@canb.auug.org.au/
drivers/net/ethernet/mellanox/mlx5/core/fw_reset.c
3d7a3f2612d7 ("net/mlx5: Nack sync reset request when HotPlug is enabled")
cecf44ea1a1f ("net/mlx5: Allow sync reset flow when BF MGT interface device is present")
https://lore.kernel.org/all/20231211110328.76c925af@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Many hardware configurations have the MDIO bus disabled, and are instead
using some other MDIO bus to talk to the MAC's phy.
of_mdiobus_register() returns -ENODEV in this case. Let's handle it
gracefully instead of failing to probe the MAC.
Fixes: 47dd7a540b8a ("net: add support for STMicroelectronics Ethernet controllers.")
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20231212-b4-stmmac-handle-mdio-enodev-v2-1-600171acf79f@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In 10M SGMII mode all the packets are being dropped due to wrong Rx clock.
SGMII 10MBPS mode needs RX clock divider programmed to avoid drops in Rx.
Update configure SGMII function with Rx clk divider programming.
Fixes: 463120c31c58 ("net: stmmac: dwmac-qcom-ethqos: add support for SGMII")
Tested-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Sneh Shah <quic_snehshah@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20231212092208.22393-1-quic_snehshah@quicinc.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The get/set_rxfh ethtool ops currently takes the rxfh (RSS) parameters
as direct function arguments. This will force us to change the API (and
all drivers' functions) every time some new parameters are added.
This is part 1/2 of the fix, as suggested in [1]:
- First simplify the code by always providing a pointer to all params
(indir, key and func); the fact that some of them may be NULL seems
like a weird historic thing or a premature optimization.
It will simplify the drivers if all pointers are always present.
- Then make the functions take a dev pointer, and a pointer to a
single struct wrapping all arguments. The set_* should also take
an extack.
Link: https://lore.kernel.org/netdev/20231121152906.2dd5f487@kernel.org/ [1]
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-2-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Device binds to proper PCI ID (LOONGSON, 0x7a03), already listed in DTS,
so checking for some other compatible does not make sense. It cannot be
bound to unsupported platform.
Drop useless, incorrect (space in between) and undocumented compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generic code will use mdio. If it is not initialized before use,
the kernel will Oops.
Fixes: 30bba69d7db4 ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Complete all counters on XGMAC Core.
These can be useful for debugging.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for cycle-time-extension. TER GCL-register needs to be
updated with the cycle-time-extension. Width of TER register is EST
time interval width + 7 bits.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231201055252.1302-4-rohan.g.thomas@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor EST implementation by moving common code for DWMAC4 and
DWXGMAC IPs into a separate EST module. EST implementation for DWMAC4
and DWXGMAC differs only for CSR base address, PTOV field offset
width, and PTOV clock multiplier value.
Thanks, Serge Semin and Jakub Kicinski for the suggestions on
refactoring EST implementation into a separate EST module.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231201055252.1302-3-rohan.g.thomas@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enabled the following EST related interrupts:
1) Constant Gate Control Error (CGCE)
2) Head-of-Line Blocking due to Scheduling (HLBS)
3) Head-of-Line Blocking due to Frame Size (HLBF)
4) Base Time Register error (BTRE)
5) Switch to S/W owned list Complete (SWLC)
Also, add EST errors into the ethtool statistic.
The commit e49aa315cb01 ("net: stmmac: EST interrupts handling and
error reporting") and commit 9f298959191b ("net: stmmac: Add EST
errors into ethtool statistic") add EST interrupts handling and error
reporting support to DWMAC4 core. This patch enables the same support
for XGMAC.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231201055252.1302-2-rohan.g.thomas@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The status bits of register MAC_FPE_CTRL_STS are clear on read. Using
32-bit read for MAC_FPE_CTRL_STS in dwmac5_fpe_configure() and
dwmac5_fpe_send_mpacket() clear the status bits. Then the stmmac interrupt
handler missing FPE event status and leads to FPE handshaking failure and
retries.
To avoid clear status bits of MAC_FPE_CTRL_STS in dwmac5_fpe_configure()
and dwmac5_fpe_send_mpacket(), add fpe_csr to stmmac_fpe_cfg structure to
cache the control bits of MAC_FPE_CTRL_STS and to avoid reading
MAC_FPE_CTRL_STS in those methods.
Fixes: 5a5586112b92 ("net: stmmac: support FPE link partner hand-shaking procedure")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jianheng Zhang <Jianheng.Zhang@synopsys.com>
Link: https://lore.kernel.org/r/CY5PR12MB637225A7CF529D5BE0FBE59CBF81A@CY5PR12MB6372.namprd12.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZWiCPAAKCRDbK58LschI
g4djAQC1FdqCRIFkhbiIRNHTgHjnfQShELQbd9ofJqzylLqmmgD+JI1E7D9SXagm
pIXQ26EGmq8/VcCT3VLncA8EsC76Gg4=
=Xowm
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-11-30
We've added 30 non-merge commits during the last 7 day(s) which contain
a total of 58 files changed, 1598 insertions(+), 154 deletions(-).
The main changes are:
1) Add initial TX metadata implementation for AF_XDP with support in mlx5
and stmmac drivers. Two types of offloads are supported right now, that
is, TX timestamp and TX checksum offload, from Stanislav Fomichev with
stmmac implementation from Song Yoong Siang.
2) Change BPF verifier logic to validate global subprograms lazily instead
of unconditionally before the main program, so they can be guarded using
BPF CO-RE techniques, from Andrii Nakryiko.
3) Add BPF link_info support for uprobe multi link along with bpftool
integration for the latter, from Jiri Olsa.
4) Use pkg-config in BPF selftests to determine ld flags which is
in particular needed for linking statically, from Akihiko Odaki.
5) Fix a few BPF selftest failures to adapt to the upcoming LLVM18,
from Yonghong Song.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (30 commits)
bpf/tests: Remove duplicate JSGT tests
selftests/bpf: Add TX side to xdp_hw_metadata
selftests/bpf: Convert xdp_hw_metadata to XDP_USE_NEED_WAKEUP
selftests/bpf: Add TX side to xdp_metadata
selftests/bpf: Add csum helpers
selftests/xsk: Support tx_metadata_len
xsk: Add option to calculate TX checksum in SW
xsk: Validate xsk_tx_metadata flags
xsk: Document tx_metadata_len layout
net: stmmac: Add Tx HWTS support to XDP ZC
net/mlx5e: Implement AF_XDP TX timestamp and checksum offload
tools: ynl: Print xsk-features from the sample
xsk: Add TX timestamp and TX checksum offload support
xsk: Support tx_metadata_len
selftests/bpf: Use pkg-config for libelf
selftests/bpf: Override PKG_CONFIG for static builds
selftests/bpf: Choose pkg-config for the target
bpftool: Add support to display uprobe_multi links
selftests/bpf: Add link_info test for uprobe_multi link
selftests/bpf: Use bpf_link__destroy in fill_link_info tests
...
====================
Conflicts:
Documentation/netlink/specs/netdev.yaml:
839ff60df3ab ("net: page_pool: add nlspec for basic access to page pools")
48eb03dd2630 ("xsk: Add TX timestamp and TX checksum offload support")
https://lore.kernel.org/all/20231201094705.1ee3cab8@canb.auug.org.au/
While at it also regen, tree is dirty after:
48eb03dd2630 ("xsk: Add TX timestamp and TX checksum offload support")
looks like code wasn't re-rendered after "render-max" was removed.
Link: https://lore.kernel.org/r/20231130145708.32573-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit aeb18dd07692 ("net: stmmac: xgmac: Disable MMC interrupts
by default") tries to disable MMC interrupts to avoid a storm of
unhandled interrupts, but leaves the FPE(Frame Preemption) MMC
interrupts enabled, FPE MMC interrupts can cause the same problem.
Now we mask FPE TX and RX interrupts to disable all MMC interrupts.
Fixes: aeb18dd07692 ("net: stmmac: xgmac: Disable MMC interrupts by default")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20231125060126.2328690-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Current implementation supports driver level VLAN tag stripping only.
The features is always on if CONFIG_VLAN_8021Q is enabled in kernel
config and is not user configurable.
This patch add support to MAC level VLAN tag stripping and can be
configured through ethtool. If the rx-vlan-offload is off, the VLAN tag
will be stripped by driver. If the rx-vlan-offload is on, the VLAN tag
will be stripped by MAC.
Command: ethtool -K <interface> rx-vlan-offload off | on
Signed-off-by: Lai Peter Jun Ann <jun.ann.lai@intel.com>
Signed-off-by: Gan, Yi Fang <yi.fang.gan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only present the DWMAC_LOONGSON option on architectures where it can
actually be used.
This follows the same logic as the DWMAC_INTEL option.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_rx_size can be set as low as 64. Rx budget might be higher than
that. Make sure to not overrun allocated rx buffers when budget is
larger.
Leave one descriptor unused to avoid wrap around of 'dirty_rx' vs
'cur_rx'.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Fixes: 47dd7a540b8a ("net: add support for STMicroelectronics Ethernet controllers.")
Link: https://lore.kernel.org/r/d95413e44c97d4692e72cec13a75f894abeb6998.1699897370.git.baruch@tkos.co.il
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The while loop condition verifies 'count < limit'. Neither value change
before the 'count >= limit' check. As is this check is dead code. But
code inspection reveals a code path that modifies 'count' and then goto
'drain_data' and back to 'read_again'. So there is a need to verify
count value sanity after 'read_again'.
Move 'read_again' up to fix the count limit check.
Fixes: ec222003bd94 ("net: stmmac: Prepare to add Split Header support")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/d9486296c3b6b12ab3a0515fcd47d56447a07bfc.1699897370.git.baruch@tkos.co.il
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
From XGMAC Core 3.20 and later, each Flexible PPS has individual PPSEN bit
to select Fixed mode or Flexible mode. The PPSEN must be set, or it stays
in Fixed PPS mode by default.
XGMAC Core prior 3.20, only PPSEN0(bit 4) is writable. PPSEN{1,2,3} are
read-only reserved, and they are already in Flexible mode by default, our
new code always set PPSEN{1,2,3} do not make things worse ;-)
Fixes: 95eaf3cd0a90 ("net: stmmac: dwxgmac: Add Flexible PPS support")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon boot up, the driver will configure the MAC capabilities based on
the maximum number of tx and rx queues. When the user changes the
tx queues to single queue, the MAC should be capable of supporting Half
Duplex, but the driver does not update the MAC capabilities when it is
configured so.
Using the stmmac_reinit_queues() to check the number of tx queues
and set the MAC capabilities accordingly.
Fixes: 0366f7e06a6b ("net: stmmac: add ethtool support for get/set channels")
Cc: <stable@vger.kernel.org> # 5.17+
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: Gan, Yi Fang <yi.fang.gan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8fce33317023 ("net: stmmac: Rework coalesce timer and fix
multi-queue races") decreased the TX coalesce timer from 40ms to 1ms.
This caused some performance regression on some target (regression was
reported at least on ipq806x) in the order of 600mbps dropping from
gigabit handling to only 200mbps.
The problem was identified in the TX timer getting armed too much time.
While this was fixed and improved in another commit, performance can be
improved even further by increasing the timer delay a bit moving from
1ms to 5ms.
The value is a good balance between battery saving by prevending too
much interrupt to be generated and permitting good performance for
internet oriented devices.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move TX timer arm call after DMA interrupt is enabled again.
The TX timer arm function changed logic and now is skipped if a napi is
already scheduled. By moving the TX timer arm call after DMA is enabled,
we permit to correctly skip if a DMA interrupt has been fired and a napi
has been scheduled again.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There is currently a problem with the TX timer getting armed multiple
unnecessary times causing big performance regression on some device that
suffer from heavy handling of hrtimer rearm.
The use of the TX timer is an old implementation that predates the napi
implementation and the interrupt enable/disable handling.
Due to stmmac being a very old code, the TX timer was never evaluated
again with this new implementation and was kept there causing
performance regression. The performance regression started to appear
with kernel version 4.19 with 8fce33317023 ("net: stmmac: Rework coalesce
timer and fix multi-queue races") where the timer was reduced to 1ms
causing it to be armed 40 times more than before.
Decreasing the timer made the problem more present and caused the
regression in the other of 600-700mbps on some device (regression where
this was notice is ipq806x).
The problem is in the fact that handling the hrtimer on some target is
expensive and recent kernel made the timer armed much more times.
A solution that was proposed was reverting the hrtimer change and use
mod_timer but such solution would still hide the real problem in the
current implementation.
To fix the regression, apply some additional logic and skip arming the
timer when not needed.
Arm the timer ONLY if a napi is not already scheduled. Running the timer
is redundant since the same function (stmmac_tx_clean) will run in the
napi TX poll. Also try to cancel any timer if a napi is scheduled to
prevent redundant run of TX call.
With the following new logic the original performance are restored while
keeping using the hrtimer.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Even though the hardware theoretically supports up to 4 simultaneous
auxiliary snapshot capture channels, the stmmac driver does support only
a single channel to be active at a time.
Previously in case of a PTP_CLK_REQ_EXTTS request, previously active
auxiliary snapshot capture channels were silently dropped and the new
channel was activated.
Instead of silently changing the state for all consumers, log an error
and return -EBUSY if a channel is already in use in order to signal to
userspace to disable the currently active channel before enabling another one.
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This is a preparation patch. The next patch will check if an external TS
is active and return with an error. So we have to move the change of the
plat->flags that tracks if external timestamping is enabled after that
check.
Prepare for this change and move the plat->flags change into the mutex
and the if (on).
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Do not store bitmask for enabling AUX_SNAPSHOT0. The previous commit
("net: stmmac: fix PPS capture input index") takes care of calculating
the proper bit mask from the request data's extts.index field, which is
0 if not explicitly specified otherwise.
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The stmmac supports up to 4 auxiliary snapshots that can be enabled by
setting the appropriate bits in the PTP_ACR bitfield.
Previously as of commit f4da56529da6 ("net: stmmac: Add support for
external trigger timestamping") instead of setting the bits, a fixed
value was written to this bitfield instead of passing the appropriate
bitmask.
Now the correct bit is set according to the ptp_clock_request.extts_index
passed as a parameter to stmmac_enable().
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Simplify the netdev_dbg() call in stmmac_enable() in order to reduce code
duplication. No functional change.
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The datatype of rx_coalesce_usecs is u32, always larger or equal to zero.
Previous checking does not include value 0, this patch removes the
checking to handle the value 0. This change in behaviour making the
value of 0 cause an error is not a problem because 0 is out of
range of rx_coalesce_usecs.
Signed-off-by: Gan Yi Fang <yi.fang.gan@intel.com>
Link: https://lore.kernel.org/r/20231018030802.741923-1-yi.fang.gan@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This is just a trivial fix for a typo in a comment, no functional
changes.
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
