IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Suggested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the nlattr header is 4 bytes in size, it can cause the netlink
attribute payload to not be 8-byte aligned.
This is particularly troublesome for IFLA_STATS64 which contains 64-bit
statistic values.
Solve this by creating a dummy IFLA_PAD attribute which has a payload
which is zero bytes in size. When HAVE_EFFICIENT_UNALIGNED_ACCESS is
false, we insert an IFLA_PAD attribute into the netlink response when
necessary such that the IFLA_STATS64 payload will be properly aligned.
With help and suggestions from Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Calm down gcc warnings:
net/netfilter/nf_conntrack_netlink.c:529:15: warning: 'ctnetlink_proto_size' defined but not used [-Wunused-function]
static size_t ctnetlink_proto_size(const struct nf_conn *ct)
^
net/netfilter/nf_conntrack_netlink.c:546:15: warning: 'ctnetlink_acct_size' defined but not used [-Wunused-function]
static size_t ctnetlink_acct_size(const struct nf_conn *ct)
^
net/netfilter/nf_conntrack_netlink.c:556:12: warning: 'ctnetlink_secctx_size' defined but not used [-Wunused-function]
static int ctnetlink_secctx_size(const struct nf_conn *ct)
^
net/netfilter/nf_conntrack_netlink.c:572:15: warning: 'ctnetlink_timestamp_size' defined but not used [-Wunused-function]
static size_t ctnetlink_timestamp_size(const struct nf_conn *ct)
^
So gcc compiles them out when CONFIG_NF_CONNTRACK_EVENTS and
CONFIG_NETFILTER_NETLINK_GLUE_CT are not set.
Fixes: 4054ff45454a9a4 ("netfilter: ctnetlink: remove unnecessary inlining")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The function convert_legacy_u32_to_link_mode and
convert_link_mode_to_legacy_u32 may be used outside
of ethtool.c. We rename them to ethtool_convert_...
and export them, so we could use them in others
drivers and modules.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_connlabel_set() takes the bit number that we would like to set.
nf_connlabels_get() however took the number of bits that we want to
support.
So e.g. nf_connlabels_get(32) support bits 0 to 31, but not 32.
This changes nf_connlabels_get() to take the highest bit that we want
to set.
Callers then don't have to cope with a potential integer wrap
when using nf_connlabels_get(bit + 1) anymore.
Current callers are fine, this change is only to make folloup
nft ct label set support simpler.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
make the replace function only send a ctnetlink event if the contents
of the new set is different.
Otherwise 'ct label set ct label | bar'
will cause netlink event storm since we "replace" labels for each packet.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently labels can only be set either by iptables connlabel
match or via ctnetlink.
Before adding nftables set support, clean up the clabel core and move
helpers that nft will not need after all to the xtables module.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We deleted a line of code and accidentally made the "return put_user()"
part of the if statement when it's supposed to be unconditional.
Fixes: 9f9a45beaa96 ('udp: do not expect udp headers on ioctl SIOCINQ')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch passes netlink attr data ptr directly to dev_get_stats
thus elimiating a stats copy.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the dsa_switch_driver.probe function to return a const char *.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code borrowed from bits and pieces of other protocols to
the IPv6 GRE path so that we can support GSO over IPv6 based GRE tunnels.
By adding this support we are able to significantly improve the throughput
for GRE tunnels as we are able to make use of GSO.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since GRE doesn't really care about L3 protocol we can support IPv4 and
IPv6 using the same offloads. With that being the case we can add a call
to register the offloads for IPv6 as a part of our GRE offload
initialization.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the basic offloads we support on most devices.
Specifically with this patch set we can support checksum offload, basic
scatter-gather, and highdma.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we were creating an ip6gretap interface the MTU was about 6 bytes
short of what was needed. It turns out we were not taking the Ethernet
header into account and as a result we were eating into the 8 bytes
reserved for the encap limit.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the IP tunnel core function iptunnel_handle_offloads so
that we return an int and do not free the skb inside the function. This
actually allows us to clean up several paths in several tunnels so that we
can free the skb at one point in the path without having to have a
secondary path if we are supporting tunnel offloads.
In addition it should resolve some double-free issues I have found in the
tunnels paths as I believe it is possible for us to end up triggering such
an event in the case of fou or gue.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two different threads with different rds sockets may be in
rds_recv_rcvbuf_delta() via receive path. If their ports
both map to the same word in the congestion map, then
using non-atomic ops to update it could cause the map to
be incorrect. Lets use atomics to avoid such an issue.
Full credit to Wengang <wen.gang.wang@oracle.com> for
finding the issue, analysing it and also pointing out
to offending code with spin lock based fix.
Reviewed-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dp->dp_ack_seq is used in big endian format. We need to do the
big endianness conversion when we assign a value in host format
to it.
Signed-off-by: Qing Huang <qing.huang@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When __vlan_insert_tag() fails from skb_vlan_push() path due to the
skb_cow_head(), we need to undo the __skb_push() in the error path
as well that was done earlier to move skb->data pointer to mac header.
Moreover, I noticed that when in the non-error path the __skb_pull()
is done and the original offset to mac header was non-zero, we fixup
from a wrong skb->data offset in the checksum complete processing.
So the skb_postpush_rcsum() really needs to be done before __skb_pull()
where skb->data still points to the mac header start and thus operates
under the same conditions as in __vlan_insert_tag().
Fixes: 93515d53b133 ("net: move vlan pop/push functions into common code")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rhashtable_walk_init return err, no release function should be
called, and when rhashtable_walk_start return err, we should only invoke
rhashtable_walk_exit to release the source.
But now when sctp_transport_walk_start return err, we just call
rhashtable_walk_stop/exit, and never care about if rhashtable_walk_init
or start return err, which is so bad.
We will fix it by calling rhashtable_walk_exit if rhashtable_walk_start
return err in sctp_transport_walk_start, and if sctp_transport_walk_start
return err, we do not need to call sctp_transport_walk_stop any more.
For sctp proc, we will use 'iter->start_fail' to decide if we will call
rhashtable_walk_stop/exit.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sctp proc, these three functions in remaddrs and assocs are the
same. we should merge them into one.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one will implement all the interface of inet_diag, inet_diag_handler.
which includes sctp_diag_dump, sctp_diag_dump_one and sctp_diag_get_info.
It will work as a module, and register inet_diag_handler when loading.
v2->v3:
- fix the mistake in inet_assoc_attr_size().
- change inet_diag_msg_laddrs_fill() name to inet_diag_msg_sctpladdrs_fill.
- change inet_diag_msg_paddrs_fill() name to inet_diag_msg_sctpaddrs_fill.
- add inet_diag_msg_sctpinfo_fill() to make asoc/ep fill code clearer.
- add inet_diag_msg_sctpasoc_fill() to make asoc fill code clearer.
- merge inet_asoc_diag_fill() and inet_ep_diag_fill() to
inet_sctp_diag_fill().
- call sctp_diag_get_info() directly, instead by handler, cause the caller
is in the same file with it.
- call lock_sock in sctp_tsp_dump_one() to make sure we call get sctp info
safely.
- after lock_sock(sk), we should check sk != assoc->base.sk.
- change mem[SK_MEMINFO_WMEM_ALLOC] to asoc->sndbuf_used for asoc dump when
asoc->ep->sndbuf_policy is set. don't use INET_DIAG_MEMINFO attr any more.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_diag_msg_common_fill is used to fill the diag msg common info,
we need to use it in sctp_diag as well, so export it.
inet_diag_msg_attrs_fill is used to fill some common attrs info between
sctp diag and tcp diag.
v2->v3:
- do not need to define and export inet_diag_get_handler any more.
cause all the functions in it are in sctp_diag.ko, we just call
them in sctp_diag.ko.
- add inet_diag_msg_attrs_fill to make codes clear.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some main variables in sctp.ko, we couldn't export it to other modules,
so we have to define some api to access them.
It will include sctp transport and endpoint's traversal.
There are some transport traversal functions for sctp_diag, we can also
use it for sctp_proc. cause they have the similar situation to traversal
transport.
v2->v3:
- rhashtable_walk_init need the parameter gfp, because of recent upstrem
update
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_diag will dump some important details of sctp's assoc or ep, we use
sctp_info to describe them, sctp_get_sctp_info to get them, and export
it to sctp_diag.ko.
v2->v3:
- we will not use list_for_each_safe in sctp_get_sctp_info, cause
all the callers of it will use lock_sock.
- fix the holes in struct sctp_info with __reserved* field.
because sctp_diag is a new feature, and sctp_info is just for now,
it may be changed in the future.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP already serializes access to rcvbuf through its sock lock:
sctp_recvmsg takes it right in the start and release at the end, while
rx path will also take the lock before doing any socket processing. On
sctp_rcv() it will check if there is an user using the socket and, if
there is, it will queue incoming packets to the backlog. The backlog
processing will do the same. Even timers will do such check and
re-schedule if an user is using the socket.
Simplifying this will allow us to remove sctp_skb_list_tail and get ride
of some expensive lockings. The lists that it is used on are also
mangled with functions like __skb_queue_tail and __skb_unlink in the
same context, like on sctp_ulpq_tail_event() and sctp_clear_pd().
sctp_close() will also purge those while using only the sock lock.
Therefore the lockings performed by sctp_skb_list_tail() are not
necessary. This patch removes this function and replaces its calls with
just skb_queue_splice_tail_init() instead.
The biggest gain is at sctp_ulpq_tail_event(), because the events always
contain a list, even if it's queueing a single skb and this was
triggering expensive calls to spin_lock_irqsave/_irqrestore for every
data chunk received.
As SCTP will deliver each data chunk on a corresponding recvmsg, the
more effective the change will be.
Before this patch, with chunks with 30 bytes:
netperf -t SCTP_STREAM -H 192.168.1.2 -cC -l 60 -- -m 30 -S 400000
400000 -s 400000 400000
on a 10Gbit link with 1500 MTU:
SCTP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.1.1 () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
425984 425984 30 60.00 137.45 7.34 7.36 52.504 52.608
With it:
SCTP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.1.1 () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
425984 425984 30 60.00 179.10 7.97 6.70 43.740 36.788
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the newer version 1 of the HSR
networking standard. Version 0 is still default and the new
version has to be selected via iproute2.
Main changes are in the supervision frame handling and its
ethertype field.
Signed-off-by: Peter Heise <peter.heise@airbus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last known hot point during SYNFLOOD attack is the clearing
of rx_opt.saw_tstamp in tcp_rcv_state_process()
It is not needed for a listener, so we move it where it matters.
Performance while a SYNFLOOD hits a single listener socket
went from 5 Mpps to 6 Mpps on my test server (24 cores, 8 NIC RX queues)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing sk_refcnt manipulation on synflood, I missed that
using skb_set_owner_w() was racy, if sk->sk_wmem_alloc had already
transitioned to 0.
We should hold sk_refcnt instead, but this is a big deal under attack.
(Doing so increase performance from 3.2 Mpps to 3.8 Mpps only)
In this patch, I chose to not attach a socket to syncookies skb.
Performance is now 5 Mpps instead of 3.2 Mpps.
Following patch will remove last known false sharing in
tcp_rcv_state_process()
Fixes: 3b24d854cb35 ("tcp/dccp: do not touch listener sk_refcnt under synflood")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the link FSM, a received traffic packet can take a link
from state ESTABLISHING to ESTABLISHED, but the link can still not be
fully set up in one atomic operation. This means that even if the the
very first packet on the link is a traffic packet with sequence number
1 (one), it has to be dropped and retransmitted.
This can be avoided if we let the mentioned packet be preceded by a
LINK_PROTOCOL/STATE message, which takes up the endpoint before the
arrival of the traffic.
We add this small feature in this commit.
This is a fully compatible change.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some link establishment scenarios we see that packet #2 may be sent
out before packet #1, forcing the receiver to demand retransmission of
the missing packet. This is harmless, but may cause confusion among
people tracing the packet flow.
Since this is extremely easy to fix, we do so by adding en extra send
call to the bearer immediately after the link has come up.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_link_timeout() is unnecessary complex, and can
easily be made more readable.
We do that with this commit. The only functional change is that we
remove a redundant test for whether the broadcast link is up or not.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link is down, it will continuously try to re-establish contact
with the peer by sending out a RESET or an ACTIVATE message at each
timeout interval. The default value for this interval is currently
375 ms. This is wasteful, and may become a problem in very large
clusters with dozens or hundreds of nodes being down simultaneously.
We now introduce a simple backoff algorithm for these cases. The
first five messages are sent at default rate; thereafter a message
is sent only each 16th timer interval.
This will cover the vast majority of link recycling cases, since the
endpoint starting last will transmit at the higher speed, and the link
should normally be established well be before the rate needs to be
reduced.
The only case where we will see a degradation of link re-establishment
times is when the endpoints remain intact, and a glitch in the
transmission media is causing the link reset. We will then experience
a worst-case re-establishing time of 6 seconds, something we deem
acceptable.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link endpoint is going down locally, e.g., because its interface
is being stopped, it will spontaneously send out a RESET message to
its peer, informing it about this fact. This saves the peer from
detecting the failure via probing, and hence gives both speedier and
less resource consuming failure detection on the peer side.
According to the link FSM, a receiver of a RESET message, ignoring the
reason for it, must now consider the sender ready to come back up, and
starts periodically sending out ACTIVATE messages to the peer in order
to re-establish the link. Also, according to the FSM, the receiver of
an ACTIVATE message can now go directly to state ESTABLISHED and start
sending regular traffic packets. This is a well-proven and robust FSM.
However, in the case of a reboot, there is a small possibilty that link
endpoint on the rebooted node may have been re-created with a new bearer
identity between the moment it sent its (pre-boot) RESET and the moment
it receives the ACTIVATE from the peer. The new bearer identity cannot
be known by the peer according to this scenario, since traffic headers
don't convey such information. This is a problem, because both endpoints
need to know the correct value of the peer's bearer id at any moment in
time in order to be able to produce correct link events for their users.
The only way to guarantee this is to enforce a full setup message
exchange (RESET + ACTIVATE) even after the reboot, since those messages
carry the bearer idientity in their header.
In this commit we do this by introducing and setting a "stopping" bit in
the header of the spontaneously generated RESET messages, informing the
peer that the sender will not be immediately ready to re-establish the
link. A receiver seeing this bit must act as if this were a locally
detected connectivity failure, and hence has to go through a full two-
way setup message exchange before any link can be re-established.
Although never reported, this problem seems to have always been around.
This protocol addition is fully backwards compatible.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts all helpers that can use ARG_PTR_TO_RAW_STACK as argument
type. For tc programs this is bpf_skb_load_bytes(), bpf_skb_get_tunnel_key(),
bpf_skb_get_tunnel_opt(). For tracing, this optimizes bpf_get_current_comm()
and bpf_probe_read(). The check in bpf_skb_load_bytes() for MAX_BPF_STACK can
also be removed since the verifier already makes sure we stay within bounds
on stack buffers.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds what's missing to properly support RPS and RFS on SCTP,
as some of it is already implemented in common calls.
Having support for RPS and RFS allows better scaling specially because
not all NICs support hashing SCTP headers.
Save the hash right when we dequeue a skb from inqueue so we do it only
once per skb instead of per chunk. New sockets will then inherit the
hash through sctp_copy_sock().
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skbs given to validate_xmit_skb() should not have a next
pointer anymore.
Also if a packet is dropped, increment dev->tx_dropped
__dev_queue_xmit() no longer has to change tx_dropped in this case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull crypto fixes from Herbert Xu:
"This fixes an NFS regression caused by the skcipher/hash conversion in
sunrpc. It also fixes a build problem in certain configurations with
bcm63xx"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: bcm63xx - fix device tree compilation
sunrpc: Fix skcipher/shash conversion
With the SO_REUSEPORT socket option, it is possible to create sockets
in the AF_INET and AF_INET6 domains which are bound to the same IPv4 address.
This is only possible with SO_REUSEPORT and when not using IPV6_V6ONLY on
the AF_INET6 sockets.
Prior to the commits referenced below, an incoming IPv4 packet would
always be routed to a socket of type AF_INET when this mixed-mode was used.
After those changes, the same packet would be routed to the most recently
bound socket (if this happened to be an AF_INET6 socket, it would
have an IPv4 mapped IPv6 address).
The change in behavior occurred because the recent SO_REUSEPORT optimizations
short-circuit the socket scoring logic as soon as they find a match. They
did not take into account the scoring logic that favors AF_INET sockets
over AF_INET6 sockets in the event of a tie.
To fix this problem, this patch changes the insertion order of AF_INET
and AF_INET6 addresses in the TCP and UDP socket lists when the sockets
have SO_REUSEPORT set. AF_INET sockets will be inserted at the head of the
list and AF_INET6 sockets with SO_REUSEPORT set will always be inserted at
the tail of the list. This will force AF_INET sockets to always be
considered first.
Fixes: e32ea7e74727 ("soreuseport: fast reuseport UDP socket selection")
Fixes: 125e80b88687 ("soreuseport: fast reuseport TCP socket selection")
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
consume_skb() isn't for error cases that kfree_skb() is more proper
one. At this patch, it fixed tpacket_rcv() and packet_rcv() to be
consistent for error or non-error cases letting perf trace its event
properly.
Signed-off-by: Weongyo Jeong <weongyo.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the requests sent to topology server are queued
to a workqueue by the generic server framework.
These messages are processed by worker threads and trigger the
registered callbacks.
To reduce latency on uniprocessor systems, explicit rescheduling
is performed using cond_resched() after MAX_RECV_MSG_COUNT(25)
messages.
This implementation on SMP systems leads to an subscriber refcnt
error as described below:
When a worker thread yields by calling cond_resched() in a SMP
system, a new worker is created on another CPU to process the
pending workitem. Sometimes the sleeping thread wakes up before
the new thread finishes execution.
This breaks the assumption on ordering and being single threaded.
The fault is more frequent when MAX_RECV_MSG_COUNT is lowered.
If the first thread was processing subscription create and the
second thread processing close(), the close request will free
the subscriber and the create request oops as follows:
[31.224137] WARNING: CPU: 2 PID: 266 at include/linux/kref.h:46 tipc_subscrb_rcv_cb+0x317/0x380 [tipc]
[31.228143] CPU: 2 PID: 266 Comm: kworker/u8:1 Not tainted 4.5.0+ #97
[31.228377] Workqueue: tipc_rcv tipc_recv_work [tipc]
[...]
[31.228377] Call Trace:
[31.228377] [<ffffffff812fbb6b>] dump_stack+0x4d/0x72
[31.228377] [<ffffffff8105a311>] __warn+0xd1/0xf0
[31.228377] [<ffffffff8105a3fd>] warn_slowpath_null+0x1d/0x20
[31.228377] [<ffffffffa0098067>] tipc_subscrb_rcv_cb+0x317/0x380 [tipc]
[31.228377] [<ffffffffa00a4984>] tipc_receive_from_sock+0xd4/0x130 [tipc]
[31.228377] [<ffffffffa00a439b>] tipc_recv_work+0x2b/0x50 [tipc]
[31.228377] [<ffffffff81071925>] process_one_work+0x145/0x3d0
[31.246554] ---[ end trace c3882c9baa05a4fd ]---
[31.248327] BUG: spinlock bad magic on CPU#2, kworker/u8:1/266
[31.249119] BUG: unable to handle kernel NULL pointer dereference at 0000000000000428
[31.249323] IP: [<ffffffff81099d0c>] spin_dump+0x5c/0xe0
[31.249323] PGD 0
[31.249323] Oops: 0000 [#1] SMP
In this commit, we
- rename tipc_conn_shutdown() to tipc_conn_release().
- move connection release callback execution from tipc_close_conn()
to a new function tipc_sock_release(), which is executed before
we free the connection.
Thus we release the subscriber during connection release procedure
rather than connection shutdown procedure.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a release_cb for UDPv6. It does a route lookup
and updates sk->sk_dst_cache if it is needed. It picks up the
left-over job from ip6_sk_update_pmtu() if the sk was owned
by user during the pmtu update.
It takes a rcu_read_lock to protect the __sk_dst_get() operations
because another thread may do ip6_dst_store() without taking the
sk lock (e.g. sendmsg).
Fixes: 45e4fd26683c ("ipv6: Only create RTF_CACHE routes after encountering pmtu exception")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reported-by: Wei Wang <weiwan@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a case in connected UDP socket such that
getsockopt(IPV6_MTU) will return a stale MTU value. The reproducible
sequence could be the following:
1. Create a connected UDP socket
2. Send some datagrams out
3. Receive a ICMPV6_PKT_TOOBIG
4. No new outgoing datagrams to trigger the sk_dst_check()
logic to update the sk->sk_dst_cache.
5. getsockopt(IPV6_MTU) returns the mtu from the invalid
sk->sk_dst_cache instead of the newly created RTF_CACHE clone.
This patch updates the sk->sk_dst_cache for a connected datagram sk
during pmtu-update code path.
Note that the sk->sk_v6_daddr is used to do the route lookup
instead of skb->data (i.e. iph). It is because a UDP socket can become
connected after sending out some datagrams in un-connected state. or
It can be connected multiple times to different destinations. Hence,
iph may not be related to where sk is currently connected to.
It is done under '!sock_owned_by_user(sk)' condition because
the user may make another ip6_datagram_connect() (i.e changing
the sk->sk_v6_daddr) while dst lookup is happening in the pmtu-update
code path.
For the sock_owned_by_user(sk) == true case, the next patch will
introduce a release_cb() which will update the sk->sk_dst_cache.
Test:
Server (Connected UDP Socket):
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Route Details:
[root@arch-fb-vm1 ~]# ip -6 r show | egrep '2fac'
2fac::/64 dev eth0 proto kernel metric 256 pref medium
2fac:face::/64 via 2fac::face dev eth0 metric 1024 pref medium
A simple python code to create a connected UDP socket:
import socket
import errno
HOST = '2fac::1'
PORT = 8080
s = socket.socket(socket.AF_INET6, socket.SOCK_DGRAM)
s.bind((HOST, PORT))
s.connect(('2fac:face::face', 53))
print("connected")
while True:
try:
data = s.recv(1024)
except socket.error as se:
if se.errno == errno.EMSGSIZE:
pmtu = s.getsockopt(41, 24)
print("PMTU:%d" % pmtu)
break
s.close()
Python program output after getting a ICMPV6_PKT_TOOBIG:
[root@arch-fb-vm1 ~]# python2 ~/devshare/kernel/tasks/fib6/udp-connect-53-8080.py
connected
PMTU:1300
Cache routes after recieving TOOBIG:
[root@arch-fb-vm1 ~]# ip -6 r show table cache
2fac:face::face via 2fac::face dev eth0 metric 0
cache expires 463sec mtu 1300 pref medium
Client (Send the ICMPV6_PKT_TOOBIG):
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
scapy is used to generate the TOOBIG message. Here is the scapy script I have
used:
>>> p=Ether(src='da:75:4d:36:ac:32', dst='52:54:00:12:34:66', type=0x86dd)/IPv6(src='2fac::face', dst='2fac::1')/ICMPv6PacketTooBig(mtu=1300)/IPv6(src='2fac::
1',dst='2fac:face::face', nh='UDP')/UDP(sport=8080,dport=53)
>>> sendp(p, iface='qemubr0')
Fixes: 45e4fd26683c ("ipv6: Only create RTF_CACHE routes after encountering pmtu exception")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reported-by: Wei Wang <weiwan@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the route lookup and update codes for connected
datagram sk to a newly created function ip6_datagram_dst_update()
It will be reused during the pmtu update in the later patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move flowi6 init codes for connected datagram sk to a newly created
function ip6_datagram_flow_key_init().
Notes:
1. fl6_flowlabel is used instead of fl6.flowlabel in __ip6_datagram_connect
2. ipv6_addr_is_multicast(&fl6->daddr) is used instead of
(addr_type & IPV6_ADDR_MULTICAST) in ip6_datagram_flow_key_init()
This new function will be reused during pmtu update in the later patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for something I am referring to as GSO partial.
The basic idea is that we can support a broader range of devices for
segmentation if we use fixed outer headers and have the hardware only
really deal with segmenting the inner header. The idea behind the naming
is due to the fact that everything before csum_start will be fixed headers,
and everything after will be the region that is handled by hardware.
With the current implementation it allows us to add support for the
following GSO types with an inner TSO_MANGLEID or TSO6 offload:
NETIF_F_GSO_GRE
NETIF_F_GSO_GRE_CSUM
NETIF_F_GSO_IPIP
NETIF_F_GSO_SIT
NETIF_F_UDP_TUNNEL
NETIF_F_UDP_TUNNEL_CSUM
In the case of hardware that already supports tunneling we may be able to
extend this further to support TSO_TCPV4 without TSO_MANGLEID if the
hardware can support updating inner IPv4 headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does two things.
First it allows TCP to aggregate TCP frames with a fixed IPv4 ID field. As
a result we should now be able to aggregate flows that were converted from
IPv6 to IPv4. In addition this allows us more flexibility for future
implementations of segmentation as we may be able to use a fixed IP ID when
segmenting the flow.
The second thing this does is that it places limitations on the outer IPv4
ID header in the case of tunneled frames. Specifically it forces the IP ID
to be incrementing by 1 unless the DF bit is set in the outer IPv4 header.
This way we can avoid creating overlapping series of IP IDs that could
possibly be fragmented if the frame goes through GRO and is then
resegmented via GSO.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for TSO using IPv4 headers with a fixed IP ID
field. This is meant to allow us to do a lossless GRO in the case of TCP
flows that use a fixed IP ID such as those that convert IPv6 header to IPv4
headers.
In addition I am adding a feature that for now I am referring to TSO with
IP ID mangling. Basically when this flag is enabled the device has the
option to either output the flow with incrementing IP IDs or with a fixed
IP ID regardless of what the original IP ID ordering was. This is useful
in cases where the DF bit is set and we do not care if the original IP ID
value is maintained.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The strings were missing for several of the GSO offloads that are
available. This patch provides the missing strings so that we can toggle
or query any of them via the ethtool command.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
