IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The WiFi firmware requires that the power is kept enabled while in
suspend mode. Add the keep-power-in-suspend property in the SDIO node
to specify that the power must be kept when entering in a system wide
suspend state.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-odroidc2.dt.yaml: gpio-regulator-tf_io: states:0: Additional items are not allowed (1800000, 1 were unexpected)
meson-gxbb-odroidc2.dt.yaml: gpio-regulator-tf_io: states:0: [3300000, 0, 1800000, 1] is too long
meson-gxbb-nexbox-a95x.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-nexbox-a95x.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxbb-p200.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-p200.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxl-s905x-hwacom-amazetv.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxl-s905x-hwacom-amazetv.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxbb-p201.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-p201.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-g12b-odroid-n2.dt.yaml: gpio-regulator-tf_io: states:0: Additional items are not allowed (1800000, 1 were unexpected)
meson-g12b-odroid-n2.dt.yaml: gpio-regulator-tf_io: states:0: [3300000, 0, 1800000, 1] is too long
meson-gxl-s905x-nexbox-a95x.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxl-s905x-nexbox-a95x.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
According the datasheets, emmc v2 chips (gxbb and gxl) don't support
more that 100Mhz in UHS-1 SD modes and HS in SDIO.
Align the max-frequency to 100MHz for UHS-1 and 50MHz for HS
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Commit 89a5e15bcba8 ("gpio/mmc/of: Respect polarity in the device tree")
changed the behavior of "cd-inverted" to follow the device tree bindings
specification:
According to SDHCI standard, CD lines are specified as "active low".
Using the "cd-inverted" property means that the CD line is "active high".
Fix the SD card description for meson by setting the cd-gpios as
"active low", according to the boards specifications, and dropping the
"cd-inverted" property.
Fixes: 89a5e15bcba8 ("gpio/mmc/of: Respect polarity in the device tree")
Signed-off-by: Loys Ollivier <lollivier@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move the SPDX-License-Identifier lines to the top and drop the
license splat.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Extend configuring the MAC address from u-boot to all meson boards.
I didn't test this changeset but having checked libretech's u-boot
tree I believe it should just work.
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Since the Data Strobe pin is optional, take it out of the default
eMMC pins and add a separate entry.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable sdcard UHS modes, up to SDR50, on p20x based boards.
While the s905 supports SDR104 mode, it appears that the PCB of p20x
based boards can't cope with a rate as high as 200Mhz.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
It does not make much sense to define cap-sd-highspeed in the emmc nodes
Just remove it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the AO CEC node in all the HDMI enabled boards DTS.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Changing the card voltage on the p200 is not instantaneous, especially
when switching from 3.3v to 1.8v.
I take at least 70ms for the regulator to go from 3.3v to 1.8v. Add
margin to that to make sure we don't upset the sdcard during the voltage
switch
Fixes: ef8d2ffedf18 ("ARM64: dts: meson-gxbb: add MMC support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Makes the override safer.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Amlogic's own .dts specifies that the P201 board uses a RMII PHY (with
the reset GPIO being GPIOZ_14).
However our P201 board .dts simply inherits the phy-mode setting from
from meson-gx.dtsi where it defaults to RGMII mode.
Remove all ethernet settings from meson-gxbb-p20x.dtsi as it only
specifies the RGMII pins which are only valid for the P200 board.
Instead we add the ethmac node to the meson-gxbb-p201.dts and configure
the pinctrl property and the phy-mode for an RMII PHY.
An MDIO node (which would also specify the PHY) is not added since we
don't know which PHY is being used (and thus which PHY address would
have to be used).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add Video Processing Unit and CVBS Output nodes, and enable CVBS on selected
boards.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add Wifi module support on the Amlogic P20x boards on the SDIO port.
The Wifi module also needs a 32768Hz clock provided by the PWM E port
through a pwm-clock node in it's power sequence.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add a 32768Hz clock generated by the PWM E port used by the WiFi module.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add binding and basic support for the SD/eMMC controller on Amlogic
S905/GXBB devices.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added nodes for GX, enabled SDIO on P20x]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
For boards only supporting 10/100 ethernet over a RMII PHY link, add
a separate pinctrl node. By the way, rename the existing node to rgmii
specific naming in all boards dts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[khilman: rename vbus node to match P200 schematics]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the Infrared Remote Controller on boards which have an Infrared
receiver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add node for ethernet interface and pinctrl pins.
Enable on odroid-C2 and P20x boards.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Update DTS and DTSI files to enable the pin controller. We also now
support the blinking blue LED on the Odroid-C2.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add minimal DT files for the Amlogic P20x development boards, based on
the Amlogic S905/GXBB SoC.
Cc: Andreas Färber <afaerber@suse.de>
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
