IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
- Add PCI_EXT_CAP_ID_PL_32GT define (Ben Dooks)
- Propagate firmware node by calling device_set_node() for better
modularity (Andy Shevchenko)
- Discover Data Link Layer Link Active Reporting earlier so quirks can take
advantage of it (Maciej W. Rozycki)
- Use cached Data Link Layer Link Active Reporting capability in pciehp,
powerpc/eeh, and mlx5 (Maciej W. Rozycki)
- Run quirk for devices that require OS to clear Retrain Link earlier, so
later quirks can rely on it (Maciej W. Rozycki)
- Export pcie_retrain_link() for use outside ASPM (Maciej W. Rozycki)
- Add Data Link Layer Link Active Reporting as another way for
pcie_retrain_link() to determine the link is up (Maciej W. Rozycki)
- Work around link training failures (especially on the ASMedia ASM2824
switch) by training first at 2.5GT/s and then attempting higher rates
(Maciej W. Rozycki)
* pci/enumeration:
PCI: Add failed link recovery for device reset events
PCI: Work around PCIe link training failures
PCI: Use pcie_wait_for_link_status() in pcie_wait_for_link_delay()
PCI: Add support for polling DLLLA to pcie_retrain_link()
PCI: Export pcie_retrain_link() for use outside ASPM
PCI: Export PCIe link retrain timeout
PCI: Execute quirk_enable_clear_retrain_link() earlier
PCI/ASPM: Factor out waiting for link training to complete
PCI/ASPM: Avoid unnecessary pcie_link_state use
PCI/ASPM: Use distinct local vars in pcie_retrain_link()
net/mlx5: Rely on dev->link_active_reporting
powerpc/eeh: Rely on dev->link_active_reporting
PCI: pciehp: Rely on dev->link_active_reporting
PCI: Initialize dev->link_active_reporting earlier
PCI: of: Propagate firmware node by calling device_set_node()
PCI: Add PCI_EXT_CAP_ID_PL_32GT define
# Conflicts:
# drivers/pci/pcie/aspm.c
PCIe r6.0.1, sec 7.5.3.7, recommends setting the link control parameters,
then waiting for the Link Training bit to be clear before setting the
Retrain Link bit.
This avoids a race where the LTSSM may not use the updated parameters if it
is already in the midst of link training because of other normal link
activity.
Wait for the Link Training bit to be clear before toggling the Retrain Link
bit to ensure that the LTSSM uses the updated link control parameters.
[bhelgaas: commit log, return 0 (success)/-ETIMEDOUT instead of bool for
both pcie_wait_for_retrain() and the existing pcie_retrain_link()]
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: 7d715a6c1a ("PCI: add PCI Express ASPM support")
Link: https://lore.kernel.org/r/20230502083923.34562-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
"pcie_retrain_link" is not a question with a true/false answer, so "bool"
isn't quite the right return type. Return 0 for success or -ETIMEDOUT if
the retrain failed. No functional change intended.
[bhelgaas: based on Ilpo's patch below]
Link: https://lore.kernel.org/r/20230502083923.34562-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Let the caller of pcie_retrain_link() specify whether they want to use the
LT bit or the DLLLA bit of the Link Status Register to determine if link
training has completed. It is up to the caller to verify whether the use
of the DLLLA bit, the implementation of which is optional, is valid for the
device requested.
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2306110310540.64925@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Export pcie_retrain_link() for link retrain needs outside ASPM. Struct
pcie_link_state is local to ASPM and only used by pcie_retrain_link() to
get at the associated PCI device, so change the operand and adjust the lone
call site accordingly. Document the interface. No functional change at
this point.
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2306110229010.64925@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Convert LINK_RETRAIN_TIMEOUT from jiffies to milliseconds, accordingly
rename to PCIE_LINK_RETRAIN_TIMEOUT_MS, and make available via "pci.h" for
the PCI core to use. Use in pcie_wait_for_link_delay().
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2305310030280.59226@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move code polling for the Link Training bit to clear into a function of its
own.
[bhelgaas: reorder to clean up before exposing to PCI core]
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2306111605060.64925@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use separate local variables to hold the respective values retrieved from
the Link Control Register and the Link Status Register. Improves
readability and it makes it possible for the compiler to detect actual
uninitialised use should this code change in the future.
[bhelgaas: reorder to clean up before exposing to PCI core]
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2306110252260.64925@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously aspm_l1ss_init() checked if ASPM_STATE_L1SS is supported before
calling aspm_calc_l12_info(), only for that function to return if
ASPM_STATE_L1_2_MASK is not supported. Simplify the logic by directly
checking for ASPM_STATE_L1_2_MASK.
Link: https://lore.kernel.org/r/20230504111301.229358-6-ajayagarwal@google.com
Signed-off-by: Ajay Agarwal <ajayagarwal@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The functions aspm_calc_l1ss_info() and calc_l1ss_pwron() perform
calculations and register programming specific to L1.2 state. Rename them
to aspm_calc_l12_info() and calc_l12_pwron() respectively.
Link: https://lore.kernel.org/r/20230504111301.229358-5-ajayagarwal@google.com
Signed-off-by: Ajay Agarwal <ajayagarwal@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously pci_enable_link_state(PCIE_LINK_STATE_L1_1) enabled only
ASPM_STATE_L1_1 and did not enable ASPM_STATE_L1. The L1.1 state only
works when L1 is enabled, so enable ASPM_STATE_L1 in addition, and do the
same for L1.2.
The only current caller is vmd_pm_enable_quirk(), which enables *all* ASPM
states, so this should have no functional effect.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20230504111301.229358-4-ajayagarwal@google.com
Signed-off-by: Ajay Agarwal <ajayagarwal@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously pci_enable_link_state(PCIE_LINK_STATE_L1) enabled L1SS as well
as L1. Enable only ASPM_STATE_L1 when the caller enables L1.
The only current caller is vmd_pm_enable_quirk(), which enables *all* ASPM
states, so this should have no functional effect.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20230504111301.229358-3-ajayagarwal@google.com
Signed-off-by: Ajay Agarwal <ajayagarwal@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Previously pci_disable_link_state(PCIE_LINK_STATE_L1) disabled L1SS as well
as L1. This is unnecessary since pcie_config_aspm_link() takes care that
L1SS is not enabled if L1 is disabled.
Disable only ASPM_STATE_L1 when the caller disables L1. No functional
changes intended.
This is consistent with aspm_attr_store_common(), which disables only L1,
not L1SS, when L1 is disabled via the sysfs "l1_aspm" file.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20230504111301.229358-2-ajayagarwal@google.com
Signed-off-by: Ajay Agarwal <ajayagarwal@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Struct pcie_link_state->downstream is a pointer to the pci_dev of function
0. Previously we retained that pointer when removing function 0, and
subsequent ASPM policy changes dereferenced it, resulting in a
use-after-free warning from KASAN, e.g.:
# echo 1 > /sys/bus/pci/devices/0000:03:00.0/remove
# echo powersave > /sys/module/pcie_aspm/parameters/policy
BUG: KASAN: slab-use-after-free in pcie_config_aspm_link+0x42d/0x500
Call Trace:
kasan_report+0xae/0xe0
pcie_config_aspm_link+0x42d/0x500
pcie_aspm_set_policy+0x8e/0x1a0
param_attr_store+0x162/0x2c0
module_attr_store+0x3e/0x80
PCIe spec r6.0, sec 7.5.3.7, recommends that software program the same ASPM
Control value in all functions of multi-function devices.
Disable ASPM and free the pcie_link_state when any child function is
removed so we can discard the dangling pcie_link_state->downstream pointer
and maintain the same ASPM Control configuration for all functions.
[bhelgaas: commit log and comment]
Debugged-by: Zongquan Qin <qinzongquan@sangfor.com.cn>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Fixes: b5a0a9b59c ("PCI/ASPM: Read and set up L1 substate capabilities")
Link: https://lore.kernel.org/r/20230507034057.20970-1-dinghui@sangfor.com.cn
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Wait longer for devices to become ready after resume (as we do for reset)
to accommodate Intel Titan Ridge xHCI devices (Mika Westerberg)
- Drop pci_bridge_wait_for_secondary_bus() timeout parameter since all
callers pass the same value (Mika Westerberg)
- Extend D3hot delay for NVIDIA HDA controllers to avoid unrecoverable
devices after a bus reset (Alex Williamson)
* pci/reset:
PCI/PM: Extend D3hot delay for NVIDIA HDA controllers
PCI/PM: Drop pci_bridge_wait_for_secondary_bus() timeout parameter
PCI/PM: Increase wait time after resume
All callers of pci_bridge_wait_for_secondary_bus() supply a timeout of
PCIE_RESET_READY_POLL_MS, so drop the parameter. Move the definition of
PCIE_RESET_READY_POLL_MS into pci.c, the only user.
[bhelgaas: extracted from
https://lore.kernel.org/r/20230404052714.51315-3-mika.westerberg@linux.intel.com]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
EDR documentation is a bit sketchy. Add a couple comments to
edr_handle_event() about the devices involved.
Link: https://lore.kernel.org/r/20230407215259.GA3825733@bhelgaas
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
During EDR recovery, the OS must clear error status of the port that
triggered DPC even if firmware retains control of DPC and AER (see the
implementation note in the PCI Firmware spec r3.3, sec 4.6.12).
Prior to 068c29a248 ("PCI/ERR: Clear PCIe Device Status errors only if
OS owns AER"), the port Device Status was cleared in this path:
edr_handle_event
dpc_process_error(dev) # "dev" triggered DPC
pcie_do_recovery(dev, dpc_reset_link)
dpc_reset_link # exit DPC
pcie_clear_device_status(dev) # clear Device Status
After 068c29a248, pcie_do_recovery() no longer clears Device Status when
firmware controls AER, so the error bit remains set even after recovery.
Per the "Downstream Port Containment configuration control" bit in the
returned _OSC Control Field (sec 4.5.1), the OS is allowed to clear error
status until it evaluates _OST, so clear Device Status in
edr_handle_event() if the error recovery was successful.
[bhelgaas: commit log]
Fixes: 068c29a248 ("PCI/ERR: Clear PCIe Device Status errors only if OS owns AER")
Link: https://lore.kernel.org/r/20230315235449.1279209-1-sathyanarayanan.kuppuswamy@linux.intel.com
Reported-by: Tsaur Erwin <erwin.tsaur@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmP2dbsUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vzBDg//aW2IeJYku5ENXwwnCQjBlyjBGOOZ
456KGpFt/ky0N9Jp0ZS3nQSa5YN7q+L8XY48gu6I7s1hXly8iLZKLrJN++S//k55
BadXu7mDUyVoY74LYvBe0nlXuwJul2qnq9IJLufRucrn1yoyqApAh39IRdCzi4U8
mP+wad7sQA0Si4bpf80uwn6Yq8SrDoO0mtmO/dZSXJooM2t2SnDXEL/fxMwTNDA4
XsVSP9FrbPmcTLo8mkDa8Dy7JKbL6KQJF9yDlmYzuA2spQpTf+YLLfsNnmE+850h
WTtfCjVaYtlik7i9qTB+VcN1CsGVepYKK3H5the16Aeql2Fu+Ji5KSt74C220Yi9
ZSDA93d/EfGc5egKyBdUUMFgqhe46srRUAoWcMrx2T4ARGuOm5EYCa9C8C7dFmO0
j6f9MYL3j2Sw3FROEKViRVOFfbIfVW1TXIo3x0fE0ud3xkg73eKp/++X8QeTMjox
2ArY2AWPNQpUI1oMlKxlSEd5XjFf7n/hHDtFqj9bIuJzt0/8wXQf0jCYTjhpGkRB
pmO+lColK6lp+bg8aWRRkiwN73xGdQhKaeXLo0Iq4T6xr0Lb3XoskHZvt6NIGe/A
ds5/uwtErq6kCf2G9YG1xfh+G1bimbjWwsHCNfSNXzTsWGDFTCb8tvqF90m+7+yl
bllxTXA6PO312Tw=
=/y4d
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Rework portdrv shutdown so it disables interrupts but doesn't
disable bus mastering, which leads to hangs on Loongson LS7A
- Add mechanism to prevent Max_Read_Request_Size (MRRS) increases,
again to avoid hardware issues on Loongson LS7A (and likely other
devices based on DesignWare IP)
- Ignore devices with a firmware (DT or ACPI) node that says the
device is disabled
Resource management:
- Distribute spare resources to unconfigured hotplug bridges at
boot-time (not just when hot-adding such a bridge), which makes
hot-adding devices to docks work better. Tried this in v6.1 but had
to revert for regressions, so try again
- Fix root bus issue that dropped resources that happened to end
at 0, e.g., [bus 00]
PCI device hotplug:
- Remove device locking when marking device as disconnected so this
doesn't have to wait for concurrent driver bind/unbind to complete
- Quirk more Qualcomm bridges that don't fully implement the PCIe
Slot Status 'Command Completed' bit
Power management:
- Account for _S0W of the target bridge in acpi_pci_bridge_d3() so we
don't miss hot-add notifications for USB4 docks, Thunderbolt, etc
Reset:
- Observe delay after reset, e.g., resuming from system sleep,
regardless of whether a bridge can suspend to D3cold at runtime
- Wait for secondary bus to become ready after a bridge reset
Virtualization:
- Avoid FLR on some AMD FCH AHCI adapters where it doesn't work
- Allow independent IOMMU groups for some Wangxun NICs that prevent
peer-to-peer transactions but don't advertise an ACS Capability
Error handling:
- Configure End-to-End-CRC (ECRC) only if Linux owns the AER
Capability
- Remove redundant Device Control Error Reporting Enable in the AER
service driver since this is already done for all devices during
enumeration
ASPM:
- Add pci_enable_link_state() interface to allow drivers to enable
ASPM link state
Endpoint framework:
- Move dra7xx and tegra194 linkup processing from hard IRQ to
threaded IRQ handler
- Add a separate lock for endpoint controller list of endpoint
function drivers to prevent deadlock in callbacks
- Pass events from endpoint controller to endpoint function drivers
via callbacks instead of notifiers
Synopsys DesignWare eDMA controller driver (acked by Vinod):
- Fix CPU vs PCI address issues
- Fix source vs destination address issues
- Fix issues with interleaved transfer semantics
- Fix channel count initialization issue (issue still exists in
several other drivers)
- Clean up and improve debugfs usage so it will work on platforms
with several eDMA devices
Baikal T-1 PCIe controller driver:
- Set a 64-bit DMA mask
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM, i.MX8MQ, i.MX8MP endpoint mode DT binding and driver
support
Intel VMD host bridge driver:
- Add quirk to configure PCIe ASPM and LTR. This is normally done by
BIOS, and will be for future products
Marvell MVEBU PCIe controller driver:
- Mark this driver as broken in Kconfig since bugs prevent its daily
usage
MediaTek MT7621 PCIe controller driver:
- Delay PHY port initialization to improve boot reliability for ZBT
WE1326, ZBT WF3526-P, and some Netgear models
Qualcomm PCIe controller driver:
- Add MSM8998 DT compatible string
- Unify MSM8996 and MSM8998 clock orderings
- Add SM8350 DT binding and driver support
- Add IPQ8074 Gen3 DT binding and driver support
- Correct qcom,perst-regs in DT binding
- Add qcom_pcie_host_deinit() so the PHY is powered off and
regulators and clocks are disabled on late host-init errors
Socionext UniPhier Pro5 controller driver:
- Clean up uniphier-ep reg, clocks, resets, and their names in DT
binding
Synopsys DesignWare PCIe controller driver:
- Restrict coherent DMA mask to 32 bits for MSI, but allow controller
drivers to set 64-bit streaming DMA mask
- Add eDMA engine support in both Root Port and Endpoint controllers
Miscellaneous:
- Remove MODULE_LICENSE from boolean drivers so they don't look like
modules so modprobe can complain about them"
* tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (86 commits)
PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
PCI: bt1: Set 64-bit DMA mask
PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
dmaengine: dw-edma: Add mem-mapped LL-entries support
PCI: Remove MODULE_LICENSE so boolean drivers don't look like modules
PCI: hv: Drop duplicate PCI_MSI dependency
PCI/P2PDMA: Annotate RCU dereference
PCI/sysfs: Constify struct kobj_type pci_slot_ktype
PCI: hotplug: Allow marking devices as disconnected during bind/unbind
PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
PCI: qcom: Add IPQ8074 Gen3 port support
dt-bindings: PCI: qcom: Add IPQ8074 Gen3 port
dt-bindings: PCI: qcom: Sort compatibles alphabetically
PCI: qcom: Fix host-init error handling
PCI: qcom: Add SM8350 support
dt-bindings: PCI: qcom: Add SM8350
dt-bindings: PCI: qcom-ep: Correct qcom,perst-regs
dt-bindings: PCI: qcom: Unify MSM8996 and MSM8998 clock order
...
- Add pci_enable_link_state() to allow drivers to enable ASPM link state
(Michael Bottini)
- Add quirk to enable all ASPM link states and program LTR for devices
below VMD (David E. Box)
* pci/controller/vmd:
PCI: vmd: Add quirk to configure PCIe ASPM and LTR
PCI: vmd: Create feature grouping for client products
PCI: vmd: Use PCI_VDEVICE in device list
PCI/ASPM: Add pci_enable_link_state()
- Always observe reset delay when waking devices from D3cold, e.g., after
system sleep, regardless of whether we're allowed to runtime-suspend to
D3cold (Lukas Wunner)
- Unify reset and resume delays to wait for downstream devices after a
bridge reset (Lukas Wunner)
- Wait for downstream devices after a DPC-induced bridge reset (Lukas
Wunner)
* pci/reset:
PCI/DPC: Await readiness of secondary bus after reset
PCI: Unify delay handling for reset and resume
PCI/PM: Observe reset delay irrespective of bridge_d3
- Implement portdrv .shutdown() method that calls service driver .remove()
methods (which disables interrupt generation as required by .shutdown()),
but doesn't disable bus mastering (which hangs on Loongson LS7A because
of a hardware defect) (Huacai Chen)
- Prevent MRRS increases for devices below Loongson LS7A to avoid hardware
limitations (Huacai Chen)
- Ignore devices with a firmware (DT/ACPI) node that says the device is
disabled (Rob Herring)
* pci/enumeration:
PCI: Honor firmware's device disabled status
PCI: loongson: Add more devices that need MRRS quirk
PCI: loongson: Prevent LS7A MRRS increases
PCI/portdrv: Prevent LS7A Bus Master clearing on shutdown
This reverts commit 5e85eba6f5.
Thomas Witt reported that 5e85eba6f5 ("PCI/ASPM: Refactor L1 PM Substates
Control Register programming") broke suspend/resume on a Tuxedo
Infinitybook S 14 v5, which seems to use a Clevo L140CU Mainboard.
The main symptom is:
iwlwifi 0000:02:00.0: Unable to change power state from D3hot to D0, device inaccessible
nvme 0000:03:00.0: Unable to change power state from D3hot to D0, device inaccessible
and the machine is only partially usable after resume. It can't run dmesg
and can't do a clean reboot. This happens on every suspend/resume cycle.
Revert 5e85eba6f5 until we can figure out the root cause.
Fixes: 5e85eba6f5 ("PCI/ASPM: Refactor L1 PM Substates Control Register programming")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216877
Reported-by: Thomas Witt <kernel@witt.link>
Tested-by: Thomas Witt <kernel@witt.link>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v6.1+
Cc: Vidya Sagar <vidyas@nvidia.com>
This reverts commit 4ff116d0d5.
Tasev Nikola and Mark Enriquez reported that resume from suspend was broken
in v6.1-rc1. Tasev bisected to a47126ec29 ("PCI/PTM: Cache PTM
Capability offset"), but we can't figure out how that could be related.
Mark saw the same symptoms and bisected to 4ff116d0d5 ("PCI/ASPM: Save L1
PM Substates Capability for suspend/resume"), which does have a connection:
it restores L1 Substates configuration while ASPM L1 may be enabled:
pci_restore_state
pci_restore_aspm_l1ss_state
aspm_program_l1ss
pci_write_config_dword(PCI_L1SS_CTL1, ctl1) # L1SS restore
pci_restore_pcie_state
pcie_capability_write_word(PCI_EXP_LNKCTL, cap[i++]) # L1 restore
which is a problem because PCIe r6.0, sec 5.5.4, requires that:
If setting either or both of the enable bits for ASPM L1 PM
Substates, both ports must be configured as described in this
section while ASPM L1 is disabled.
Separately, Thomas Witt reported that 5e85eba6f5 ("PCI/ASPM: Refactor L1
PM Substates Control Register programming") broke suspend/resume, and it
depends on 4ff116d0d5.
Revert 4ff116d0d5 ("PCI/ASPM: Save L1 PM Substates Capability for
suspend/resume") to fix the resume issue and enable revert of 5e85eba6f5
to fix the issue Thomas reported.
Note that reverting 4ff116d0d5 means L1 Substates config may be lost on
suspend/resume. As far as we know the system will use more power but will
still *work* correctly.
Fixes: 4ff116d0d5 ("PCI/ASPM: Save L1 PM Substates Capability for suspend/resume")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216782
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216877
Reported-by: Tasev Nikola <tasev.stefanoska@skynet.be>
Reported-by: Mark Enriquez <enriquezmark36@gmail.com>
Reported-by: Thomas Witt <kernel@witt.link>
Tested-by: Mark Enriquez <enriquezmark36@gmail.com>
Tested-by: Thomas Witt <kernel@witt.link>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v6.1+
Cc: Vidya Sagar <vidyas@nvidia.com>
pci_bridge_wait_for_secondary_bus() is called after a Secondary Bus
Reset, but not after a DPC-induced Hot Reset.
As a result, the delays prescribed by PCIe r6.0 sec 6.6.1 are not
observed and devices on the secondary bus may be accessed before
they're ready.
One affected device is Intel's Ponte Vecchio HPC GPU. It comprises a
PCIe switch whose upstream port is not immediately ready after reset.
Because its config space is restored too early, it remains in
D0uninitialized, its subordinate devices remain inaccessible and DPC
recovery fails with messages such as:
i915 0000:8c:00.0: can't change power state from D3cold to D0 (config space inaccessible)
intel_vsec 0000:8e:00.1: can't change power state from D3cold to D0 (config space inaccessible)
pcieport 0000:89:02.0: AER: device recovery failed
Fix it.
Link: https://lore.kernel.org/r/9f5ff00e1593d8d9a4b452398b98aa14d23fca11.1673769517.git.lukas@wunner.de
Tested-by: Ravi Kishore Koppuravuri <ravi.kishore.koppuravuri@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Add pci_enable_link_state() to allow devices to change the default BIOS
configured states. Clears the BIOS default settings then sets the new
states and reconfigures the link under the semaphore. Also add
PCIE_LINK_STATE_ALL macro for convenience for callers that want to enable
all link states.
Link: https://lore.kernel.org/r/20230120031522.2304439-2-david.e.box@linux.intel.com
Signed-off-by: Michael Bottini <michael.a.bottini@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
After cc27b735ad ("PCI/portdrv: Turn off PCIe services during shutdown")
we observe hangs during poweroff/reboot on systems with LS7A chipset.
This happens because the portdrv .shutdown() method (pcie_portdrv_remove())
clears PCI_COMMAND_MASTER via pci_disable_device(), which prevents bridges
from forwarding memory or I/O Requests in the upstream direction (PCIe
r6.0, sec 7.5.1.1.3).
LS7A Root Ports have a hardware defect: clearing PCI_COMMAND_MASTER *also*
prevents the bridge from forwarding CPU MMIO requests in the downstream
direction, and these MMIO accesses to devices below the bridge happen even
after .shutdown(), e.g., to print console messages. LS7A neither forwards
the requests nor sends an unsuccessful completion to the CPU, so the CPU
waits forever, resulting in the hang.
The purpose of .shutdown() is to disable interrupts and DMA from the
device. PCIe ports may generate interrupts (either MSI/MSI-X or INTx) for
AER, DPC, PME, hotplug, etc., but they never perform DMA except MSI/MSI-X.
Clearing PCI_COMMAND_MASTER effectively disables MSI/MSI-X, but not INTx.
The port service driver .remove() methods clear the interrupt enables in
PCI_ERR_ROOT_COMMAND, PCI_EXP_DPC_CTL, PCI_EXP_SLTCTL, and PCI_EXP_RTCTL,
etc., which disables interrupts regardless of whether they are MSI/MSI-X or
INTx.
Add a pcie_portdrv_shutdown() method that calls all the port service driver
.remove() methods to clear the interrupt enables for each service but does
not clear Bus Mastering on the port itself.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20230201043018.778499-2-chenhuacai@loongson.cn
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The following bits in the PCIe Device Control register enable sending of
ERR_COR, ERR_NONFATAL, or ERR_FATAL Messages (or reporting internally in
the case of Root Ports):
Correctable Error Reporting Enable
Non-Fatal Error Reporting Enable
Fatal Error Reporting Enable
Unsupported Request Reporting Enable
These enable bits are set by pci_enable_pcie_error_reporting(), and since
f26e58bf6f ("PCI/AER: Enable error reporting when AER is native"), we
do that in this path during enumeration:
pci_init_capabilities
pci_aer_init
pci_enable_pcie_error_reporting
Previously, the AER service driver also traversed the hierarchy when
claiming a Root Port, enabling error reporting for downstream devices, but
this is redundant.
Remove the code that enables this error reporting in the AER .probe() path.
Also remove similar code that disables error reporting in the AER .remove()
path.
Note that these Device Control Reporting Enable bits do not control
interrupt generation. That's done by the similarly-named bits in the AER
Root Error Command register, which are still set by aer_probe() and cleared
by aer_remove(), since the AER service driver handles those interrupts.
See PCIe r6.0, sec 6.2.6.
Link: https://lore.kernel.org/r/20230118234612.272916-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <kbusch@kernel.org>
As the ECRC configuration bits are part of AER registers, configure ECRC
only if AER is natively owned by the kernel.
Link: https://lore.kernel.org/r/20230112072111.20063-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----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=KULr
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Squash portdrv_{core,pci}.c into portdrv.c to ease maintenance and
make more things static.
- Make portdrv bind to Switch Ports that have AER. Previously, if
these Ports lacked MSI/MSI-X, portdrv failed to bind, which meant
the Ports couldn't be suspended to low-power states. AER on these
Ports doesn't use interrupts, and the AER driver doesn't need to
claim them.
- Assign PCI domain IDs using ida_alloc(), which makes host bridge
add/remove work better.
Resource management:
- To work better with recent BIOSes that use EfiMemoryMappedIO for
PCI host bridge apertures, remove those regions from the E820 map
(E820 entries normally prevent us from allocating BARs). In v5.19,
we added some quirks to disable E820 checking, but that's not very
maintainable. EfiMemoryMappedIO means the OS needs to map the
region for use by EFI runtime services; it shouldn't prevent OS
from using it.
PCIe native device hotplug:
- Build pciehp by default if USB4 is enabled, since Thunderbolt/USB4
PCIe tunneling depends on native PCIe hotplug.
- Enable Command Completed Interrupt only if supported to avoid user
confusion from lspci output that says this is enabled but not
supported.
- Prevent pciehp from binding to Switch Upstream Ports; this happened
because of interaction with acpiphp and caused devices below the
Upstream Port to disappear.
Power management:
- Convert AGP drivers to generic power management. We hope to remove
legacy power management from the PCI core eventually.
Virtualization:
- Fix pci_device_is_present(), which previously always returned
"false" for VFs, causing virtio hangs when unbinding the driver.
Miscellaneous:
- Convert drivers to gpiod API to prepare for dropping some legacy
code.
- Fix DOE fencepost error for the maximum data object length.
Baikal-T1 PCIe controller driver:
- Add driver and DT bindings.
Broadcom STB PCIe controller driver:
- Enable Multi-MSI.
- Delay 100ms after PERST# deassert to allow power and clocks to
stabilize.
- Configure Read Completion Boundary to 64 bytes.
Freescale i.MX6 PCIe controller driver:
- Initialize PHY before deasserting core reset to fix a regression in
v6.0 on boards where the PHY provides the reference.
- Fix imx6sx and imx8mq clock names in DT schema.
Intel VMD host bridge driver:
- Fix Secondary Bus Reset on VMD bridges, which allows reset of NVMe
SSDs in VT-d pass-through scenarios.
- Disable MSI remapping, which gets re-enabled by firmware during
suspend/resume.
MediaTek PCIe Gen3 controller driver:
- Add MT7986 and MT8195 support.
Qualcomm PCIe controller driver:
- Add SC8280XP/SA8540P basic interconnect support.
Rockchip DesignWare PCIe controller driver:
- Base DT schema on common Synopsys schema.
Synopsys DesignWare PCIe core:
- Collect DT items shared between Root Port and Endpoint (PERST GPIO,
PHY info, clocks, resets, link speed, number of lanes, number of
iATU windows, interrupt info, etc) to snps,dw-pcie-common.yaml.
- Add dma-ranges support for Root Ports and Endpoints.
- Consolidate DT resource retrieval for "dbi", "dbi2", "atu", etc. to
reduce code duplication.
- Add generic names for clocks and resets to encourage more
consistent naming across drivers using DesignWare IP.
- Stop advertising PTM Responder role for Endpoints, which aren't
allowed to be responders.
TI J721E PCIe driver:
- Add j721s2 host mode ID to DT schema.
- Add interrupt properties to DT schema.
Toshiba Visconti PCIe controller driver:
- Fix interrupts array max constraints in DT schema"
* tag 'pci-v6.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (95 commits)
x86/PCI: Use pr_info() when possible
x86/PCI: Fix log message typo
x86/PCI: Tidy E820 removal messages
PCI: Skip allocate_resource() if too little space available
efi/x86: Remove EfiMemoryMappedIO from E820 map
PCI/portdrv: Allow AER service only for Root Ports & RCECs
PCI: xilinx-nwl: Fix coding style violations
PCI: mvebu: Switch to using gpiod API
PCI: pciehp: Enable Command Completed Interrupt only if supported
PCI: aardvark: Switch to using devm_gpiod_get_optional()
dt-bindings: PCI: mediatek-gen3: add support for mt7986
dt-bindings: PCI: mediatek-gen3: add SoC based clock config
dt-bindings: PCI: qcom: Allow 'dma-coherent' property
PCI: mt7621: Add sentinel to quirks table
PCI: vmd: Fix secondary bus reset for Intel bridges
PCI: endpoint: pci-epf-vntb: Fix sparse ntb->reg build warning
PCI: endpoint: pci-epf-vntb: Fix sparse build warning for epf_db
PCI: endpoint: pci-epf-vntb: Replace hardcoded 4 with sizeof(u32)
PCI: endpoint: pci-epf-vntb: Remove unused epf_db_phy struct member
PCI: endpoint: pci-epf-vntb: Fix call pci_epc_mem_free_addr() in error path
...
- Squash portdrv_core.c and portdrv_pci.c into portdrv.c to make it easier
to find things (Bjorn Helgaas)
- Allow AER service only for Root Ports & RCECs so portdrv can successfully
bind to other devices that have AER but lack MSI (which they don't need
for AER), which allows power management for those devices (Bjorn Helgaas)
* pci/portdrv:
PCI/portdrv: Allow AER service only for Root Ports & RCECs
PCI/portdrv: Unexport pcie_port_service_register(), pcie_port_service_unregister()
PCI/portdrv: Move private things to portdrv.c
PCI/portdrv: Squash into portdrv.c
Previously portdrv allowed the AER service for any device with an AER
capability (assuming Linux had control of AER) even though the AER service
driver only attaches to Root Port and RCECs.
Because get_port_device_capability() included AER for non-RP, non-RCEC
devices, we tried to initialize the AER IRQ even though these devices
don't generate AER interrupts.
Intel DG1 and DG2 discrete graphics cards contain a switch leading to a
GPU. The switch supports AER but not MSI, so initializing an AER IRQ
failed, and portdrv failed to claim the switch port at all. The GPU itself
could be suspended, but the switch could not be put in a low-power state
because it had no driver.
Don't allow the AER service on non-Root Port, non-Root Complex Event
Collector devices. This means we won't enable Bus Mastering if the device
doesn't require MSI, the AER service will not appear in sysfs, and the AER
service driver will not bind to the device.
Link: https://lore.kernel.org/r/20221207084105.84947-1-mika.westerberg@linux.intel.com
Link: https://lore.kernel.org/r/20221210002922.1749403-1-helgaas@kernel.org
Based-on-patch-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Some new devices such as CXL devices may want to record additional error
information on a corrected error. Add a callback to allow the PCI device
driver to do additional logging such as providing additional stats for user
space RAS monitoring.
For CXL device, this is actually a need due to CXL needing to write to the
CXL RAS capability structure correctable error status register in order to
clear the unmasked correctable errors. See CXL spec rev3.0 8.2.4.16.
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/166984619233.2804404.3966368388544312674.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
It is reported that on some systems pciehp binds to an Upstream Port and
attempts to operate it which causes devices below the Port to disappear
from the bus.
This happens because acpiphp sets dev->is_hotplug_bridge for that Port
(after receiving a Device Check notification on it from the platform
firmware via ACPI) during the enumeration of PCI devices.
get_port_device_capability() sees that dev->is_hotplug_bridge is set and
adds PCIE_PORT_SERVICE_HP to Port services (which allows pciehp to bind to
the Port in question) without consulting the PCIe type, which should be
either Root Port or Downstream Port for the hotplug capability to be
present.
Per PCIe r6.0, sec 7.5.3.2, the Slot Implemented bit is only valid for
Downstream Ports (including Root Ports), and PCIe hotplug depends on the
Slot Capabilities / Control / Status registers.
Make get_port_device_capability() more robust by adding a PCIe type check
to it before adding PCIE_PORT_SERVICE_HP to Port services which helps to
avoid the problem.
[bhelgaas: add spec citation]
Suggested-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/4786090.31r3eYUQgx@kreacher
Reported-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
pcie_port_service_register() and pcie_port_service_unregister() are used
only by the pciehp, aer, dpc, and pme PCIe port service drivers, none of
which can be modules. Unexport pcie_port_service_register() and
pcie_port_service_unregister(). No functional change intended.
Link: https://lore.kernel.org/r/20221019204127.44463-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Previously several things used by portdrv_core.c and portdrv_pci.c were
shared by defining them in portdrv.h. Now that portdrv_core.c and
portdrv_pci.c have been squashed, move things that can be private into
portdrv.c. No functional change intended.
Link: https://lore.kernel.org/r/20221019204127.44463-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Squash portdrv_core.c and portdrv_pci.c into portdrv.c to make it easier to
find things. The whole thing is less than 1000 lines, and it's a pain to
bounce back and forth between two files.
Several portdrv_core.c functions were non-static because they were
referenced from portdrv_pci.c. Make them static since they're now all in
portdrv.c.
No functional change intended.
Link: https://lore.kernel.org/r/20221019204127.44463-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
- Cache the PTM capability offset instead of searching for it every time
(Bjorn Helgaas)
- Separate PTM configuration from PTM enable (Bjorn Helgaas)
- Add pci_suspend_ptm() and pci_resume_ptm() to disable and re-enable PTM
on suspend/resume so some Root Ports can safely enter a lower-power PM
state (Bjorn Helgaas)
- Disable PTM for all devices during suspend; previously we only did this
for Root Ports and even then only in certain cases (Bjorn Helgaas)
- Simplify pci_pm_suspend_noirq() (Rajvi Jingar)
- Reduce the delay after transitions to/from D3hot by using usleep_range()
instead of msleep(), which reduces the typical delay from 19ms to 10ms
(Sajid Dalvi, Will McVicker)
* pci/pm:
PCI/PM: Reduce D3hot delay with usleep_range()
PCI/PM: Simplify pci_pm_suspend_noirq()
PCI/PM: Always disable PTM for all devices during suspend
PCI/PTM: Consolidate PTM interface declarations
PCI/PTM: Reorder functions in logical order
PCI/PTM: Preserve RsvdP bits in PTM Control register
PCI/PTM: Move pci_ptm_info() body into its only caller
PCI/PTM: Add pci_suspend_ptm() and pci_resume_ptm()
PCI/PTM: Separate configuration and enable
PCI/PTM: Add pci_upstream_ptm() helper
PCI/PTM: Cache PTM Capability offset
- Work around a BIOS defect that makes some Intel Root Ports report an RP
PIO log size of zero (Mika Westerberg)
* pci/dpc:
PCI/DPC: Quirk PIO log size for certain Intel Root Ports
80d7d7a904 ("PCI/ASPM: Calculate LTR_L1.2_THRESHOLD from device
characteristics") replaced a fixed value (163840ns) with one computed from
T_POWER_OFF, Common_Mode_Restore_Time, etc., but it encoded the
LTR_L1.2_THRESHOLD value incorrectly.
This is especially a problem for small thresholds, e.g., 63ns fell into the
"threshold_ns < 1024" case and was encoded as 32ns:
LTR_L1.2_THRESHOLD_Scale = 1 (multiplier is 32ns)
LTR_L1.2_THRESHOLD_Value = 63 >> 5 = 1
LTR_L1.2_THRESHOLD = multiplier * value = 32ns * 1 = 32ns
Correct the algorithm to encode all times of 1023ns (0x3ff) or smaller
exactly and larger times conservatively (the encoded threshold is never
smaller than was requested). This reduces the chance of entering L1.2
when the device can't tolerate the exit latency.
Fixes: 80d7d7a904 ("PCI/ASPM: Calculate LTR_L1.2_THRESHOLD from device characteristics")
Link: https://lore.kernel.org/r/20221005025809.2247547-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
187f91db82 ("PCI/ASPM: Remove struct aspm_register_info.l1ss_cap")
inadvertently removed a check for existence of the L1 PM Substates (L1SS)
Capability before reading it.
If there is no L1SS Capability, this means we mistakenly read PCI_COMMAND
and PCI_STATUS (config address 0x04) and interpret that as the PCI_L1SS_CAP
register, so we may incorrectly configure L1SS.
Make sure the L1SS Capability exists before trying to read it.
Fixes: 187f91db82 ("PCI/ASPM: Remove struct aspm_register_info.l1ss_cap")
Link: https://lore.kernel.org/r/20221005025809.2247547-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Previously the L1 PM Substates Control Registers (CTL1 and CTL2) weren't
saved and restored during suspend/resume leading to the L1 PM Substates
configuration being lost post-resume.
Save the L1 PM Substates Control Registers so that the configuration is
retained post-resume.
[bhelgaas: drop pci_is_pcie() testing; we can rely on pci_configure_ltr()
having already done that]
Link: https://lore.kernel.org/r/20220913131822.16557-3-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some Root Ports on Intel Tiger Lake and Alder Lake systems support the RP
Extensions for DPC and the RP PIO Log registers but incorrectly advertise
an RP PIO Log Size of zero. This means the kernel complains that:
DPC: RP PIO log size 0 is invalid
and if DPC is triggered, the DPC driver will not dump the RP PIO Log
registers when it should.
This is caused by a BIOS bug and should be fixed the BIOS for future CPUs.
Add a quirk to set the correct RP PIO Log size for the affected Root Ports.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209943
Link: https://lore.kernel.org/r/20220816102042.69125-1-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
pci_enable_ptm() and pci_disable_ptm() were separated.
pci_save_ptm_state() and pci_restore_ptm_state() dangled at the top. Move
them to logical places. No functional change intended.
Link: https://lore.kernel.org/r/20220909202505.314195-8-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Even though only the low 16 bits of PTM Control are currently defined, the
register is 32 bits wide and the unused bits are RsvdP ("Reserved and
Preserved"), so software must preserve the values of those bits when
writing the register.
Update PTM Control reads and writes to use 32-bit accesses and preserve the
reserved bits on writes.
Link: https://lore.kernel.org/r/20220909202505.314195-7-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
