IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
for various devices. Also included is a memory controller (GPMC) debug output
fix as without that the shown bootloader configured GPMC bus width will
be wrong and won't work for kernel timings:
- Add dra7 powerhold configuration to be able to shut down pmic correctly
- Fix polarity for gta04 mcbsp4 clocks for modem
- Fix Pandaboard CEC pin pull making it usable
- Fix LogicPD Torpedo camera pin mux
- Fix GPMC debug bus width
- Reduce cpu thermal shutdown temperature
-----BEGIN PGP SIGNATURE-----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=My0U
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.12/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.12-rc cycle most consisting of few minor dts fixes
for various devices. Also included is a memory controller (GPMC) debug output
fix as without that the shown bootloader configured GPMC bus width will
be wrong and won't work for kernel timings:
- Add dra7 powerhold configuration to be able to shut down pmic correctly
- Fix polarity for gta04 mcbsp4 clocks for modem
- Fix Pandaboard CEC pin pull making it usable
- Fix LogicPD Torpedo camera pin mux
- Fix GPMC debug bus width
- Reduce cpu thermal shutdown temperature
* tag 'omap-for-v4.12/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7: Reduce cpu thermal shutdown temperature
memory: omap-gpmc: Fix debug output for access width
ARM: dts: LogicPD Torpedo: Fix camera pin mux
ARM: dts: omap4: enable CEC pin for Pandaboard A4 and ES
ARM: dts: gta04: fix polarity of clocks for mcbsp4
ARM: dts: dra7: Add power hold and power controller properties to palmas
Signed-off-by: Olof Johansson <olof@lixom.net>
- A fix on GPCv2 power domain driver Kconfig which causes a build
failure when CONFIG_PM is not set.
- Pull down PMIC IRQ pin for imx53-qsrb board to prevent spurious
PMIC interrupts from happening.
- Remove board level OPP override for imx6sx-sdb to fix a boot crash
seen on Rev.C boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZHav8AAoJEFBXWFqHsHzOPWMH/RP4LuJDUoFaPUJ3WsrMhPYR
qmBEzZXvjKBxImFCIiG09vcjQIiN9p5uZ9AqNIQGgoW20DlFKVZ0Rd64MJzp8QnL
J/WwEDTG1qs2jCkNWYkFEUwz6fMWzzTUydj665dkQI3SNwRAJ9dE0LgybM6Yws3C
FQdIUyWR2z8QQYqjLTD9XuDe7ewyoslvFssWRiVzpcnkiu8sWgbTuJ/K+ISCgwo4
rC6Vi7Z4WU47SgL7+d9sOMzDPDIif5mOdfW8uG3tgCeDp/8WNz9IbamCuxhggQpa
+k9jaTHAtOV9ypf1PBUCGHazU7E8hc42XoW6XT0yY3sFynw+VPd1IFVXiWAEBu0=
=gQA8
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.12:
- A fix on GPCv2 power domain driver Kconfig which causes a build
failure when CONFIG_PM is not set.
- Pull down PMIC IRQ pin for imx53-qsrb board to prevent spurious
PMIC interrupts from happening.
- Remove board level OPP override for imx6sx-sdb to fix a boot crash
seen on Rev.C boards.
* tag 'imx-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: add PM dependency for IMX7_PM_DOMAINS
ARM: dts: imx6sx-sdb: Remove OPP override
ARM: dts: imx53-qsrb: Pulldown PMIC IRQ pin
Signed-off-by: Olof Johansson <olof@lixom.net>
4.12, please pull the following:
- Baruch provides several fixes for the Raspberry Pi (BCM2835) Device
Tree source include file: uart0 pinctrl node names, pin number for
i2c0, uart0 rts/cts pins and invalid uart1 pin, missing numbers for
ethernet aliases
-----BEGIN PGP SIGNATURE-----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=6jUO
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.12/devicetree-fixes' of http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for
4.12, please pull the following:
- Baruch provides several fixes for the Raspberry Pi (BCM2835) Device
Tree source include file: uart0 pinctrl node names, pin number for
i2c0, uart0 rts/cts pins and invalid uart1 pin, missing numbers for
ethernet aliases
* tag 'arm-soc/for-4.12/devicetree-fixes' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm2835: add index to the ethernet alias
ARM: dts: bcm2835: fix uart0/uart1 pins
ARM: dts: bcm2835: fix i2c0 pins
ARM: dts: bcm2835: fix uart0 pinctrl node names
Signed-off-by: Olof Johansson <olof@lixom.net>
We use a directory under arch/$ARCH/boot/dts as an include path
that has links outside of the subtree to find dt-bindings from under
include/dt-bindings. That's been working well, but new DT architectures
haven't been adding them by default.
Recently there's been a desire to share some of the DT material between
arm and arm64, which originally caused developers to create symlinks or
relative includes between the subtrees. This isn't ideal -- it breaks
if the DT files aren't stored in the exact same hierarchy as the kernel
tree, and generally it's just icky.
As a somewhat cleaner solution we decided to add a $ARCH/ prefix link
once, and allow DTS files to reference dtsi (and dts) files in other
architectures that way.
Original approach was to create these links under each architecture,
but it lead to the problem of recursive symlinks.
As a remedy, move the include link directories out of the architecture
trees into a common location. At the same time, they can now share one
directory and one dt-bindings/ link as well.
Fixes: 4027494ae6e3 ('ARM: dts: add arm/arm64 include symlinks')
Reported-by: Russell King <linux@armlinux.org.uk>
Reported-by: Omar Sandoval <osandov@osandov.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: linux-arch <linux-arch@vger.kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZF2pwAAoJEHm+PkMAQRiG9aAIAJJyV6Ux9kaX+glqO3KIs0wm
0K/yqMOv1JTfJ1UUgY4iZbk5XOPPmXv1bdKJFECZfuAHdymJUF/RVNNvDlZbaLdd
K8vDEi92eRwcf07a5b/Q2F8yNfADKKmRAA/oAbuQLBhJ0dPHig70PIvi9gq9kqiE
Ft1MinbsZLavYatLm7oVDr/nsYebEDMGwTy0EX5bF2YjydfAlCvVWnI5ld5wisiV
0fQF4W7MMjjcpAzG8uq3atEB8iQcWS2Ykz2chZRbYzHcdV2WJW751Vge9xc05Hzi
rxlqn6peZFiFyM0qdPLhY0ktGzSTZcCFeb3aZicvm5aOamy2KJjOSZrEwjU8kts=
=VHpx
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc1' into fixes
We've received a few fixes branches with -rc1 as base, but our contents was
still at pre-rc1. Merge it in expliticly to make 'git merge --log' clear on
hat was actually merged.
Signed-off-by: Olof Johansson <olof@lixom.net>
On imx6sx-sdb rev B/C the VDD_ARM_IN and VDD_SOC_IN supplies are connected
together and both are supplied by the SW1A PMIC output, so model this
correctly in the device tree.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Allwinner V3s SoC has a SPI controller, muxed with the MMC2 controller
at PC bank. The controller itself is identical to the one in H3 SoC.
Add device tree node and the only pinmux node for it.
Tested with a Winbond W25Q128FV SPI NOR soldered on the Lichee Pi
early sample.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Lichee Pi Zero board has a "dock board" which needs to be soldered
with the 1.27mm stamp holes on a Lichee Pi Zero board.
It features:
- Onboard MIC and headphone jack (not supported yet)
- Ethernet port (not supported yet)
- An extra MicroSD slot connected to MMC1 controller
- four keys connected to the LRADC.
As it needs to be soldered with the main board to use, add a stand-alone
device tree for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add secondary pinctrl set for UART2 which can be used to prevent conflicts
with sdmmc pins.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Correct UART2 PINCTRL flag to use the correct pull up setting
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Refer to Chapter 5.3.2 of rk3229 TRM, we can see that GPIO1A[2,4,5]
using RK_FUNC_2 not RK_FUNC_1. This patch fixes it.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On dra7, as per TRM, the HW shutdown (TSHUT) temperature is hardcoded
to 123C and cannot be modified by SW. This means when the temperature
reaches 123C HW asserts TSHUT output which signals a warm reset.
This reset is held until the temperature goes below the TSHUT low (105C).
While in SW, the thermal driver continuously monitors current temperature
and takes decisions based on whether it reached an alert or a critical point.
The intention of setting a SW critical point is to prevent force reset by HW
and instead do an orderly_poweroff(). But if the SW critical temperature is
greater than or equal to that of HW then it defeats the purpose. To address
this and let SW take action before HW does keep the SW critical temperature
less than HW TSHUT value.
The value for SW critical temperature was chosen as 120C just to ensure
we give SW sometime before HW catches up.
Document reference
SPRUI30C – DRA75x, DRA74x Technical Reference Manual - November 2016
SPRUHZ6H - AM572x Technical Reference Manual - November 2016
Tested on:
DRA75x PG 2.0 Rev H EVM
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds a new node to the LEGO MINDSTORMS EV3 device tree for the battery.
Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: minor headline fix]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
sdcard access with the sdhost controller is faster.
Read access (dd with 64k blocks on rpi2):
CONFIG_MMC_SDHCI_IPROC: 11-12 MB/s
CONFIG_MMC_BCM2835: 19-20 MB/s
Differences on write access are pretty much in the noise.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Eric Anholt <eric@anholt.net>
If we have Linux installed in eMMC we can boot without
µSD card, but inserting one is not recognised.
The reason is that the card detect gpio (gpio5_152)
is not configured and attached to the mmc1 interface
driver and the mmc driver does not poll by default.
Hence we add pinmux and gpio setup for the SDCARD_NCD
signal.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Droid 4 has WL 1285C connected to the OMAP's UART4 port, which is
used for Bluetooth and most likely can also be used for controlling
the FM radio and GPS receivers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
USB1 port is micro-AB type and can function as peripheral
as well as host. Enable dual-role mode for USB1.
We don't want to use the OTG controller block on this
platform as it limits host mode to high-speed. Instead
we rely on extcon framework to give us ID events for
dual-role mode detection.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The rv4162 compatbile string is missing the vendor part, add it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix commit 05c4ffc3a266 ("ARM: dts: LogicPD Torpedo: Add MT9P031 Support")
In the previous commit, I indicated that the only testing was done by
showing the camera showed up when probing. This patch fixes an incorrect
pin muxing on cam_d0, cam_d1 and cam_d2.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CEC pin was always pulled up, making it impossible to use it.
Change to PIN_INPUT so it can be used by the new CEC support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The clock polarity setting of the mcbsp connected to
the modem was wrong so almost only noise
was received.
With this patch it is also the same as it was on
earlier non-dt kernels where it was working properly
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add power hold and power controller properties to palmas node.
This is needed to shutdown pmic correctly on boards with
powerhold set.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As suggested by Eduardo Valentin this adds the thermal zone for
the bcm2835 SoC with its single thermal sensor. We start with
the criticial trip point and leave the cooling devices empty
since we don't have any at the moment. Since the coefficients
could vary depending on the SoC we need to define them separate.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Raspbian and Fedora have decided to support the Pi3 in 32-bit mode for
now, so it's useful to be able to test that mode on an upstream
kernel. It's also been useful for me to use the same board for 32-bit
and 64-bit development.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Olof Johansson <olof@lixom.net>
The Raspberry Pi startup stub files for multi-core BCM283X processors
make the secondary CPUs spin until the corresponding mailbox is
written. These stubs are loaded at physical address 0x00000xxx (as seen
by the ARMs), but this page will be reused by the kernel unless it is
explicitly reserved, causing the waiting cores to execute random code.
Use the /memreserve/ Device Tree directive to mark the first page as
off-limits to the kernel.
See: https://github.com/raspberrypi/linux/issues/1989
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
During my research I found that some of the requirements for the memory
buffers for MFC v6+ devices were blindly copied from the previous (v5)
version and simply turned out to be excessive. The relaxed requirements
are applied by the recent patches to the MFC driver and the driver is
now fully functional even without the reserved memory blocks for all
v6+ variants. This patch removes those reserved memory nodes from all
boards having MFC v6+ hardware block.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
When running a stress playback/stop loop test on a mx6colibri channel
swaps can be noticed randomly.
Increasing the SGTL5000 LRCLK pad strength to its maximum value fixes
the issue, so add the 'lrclk-strength' property to avoid the audio
channel swaps.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When running a stress playback/stop loop test on a mx6wandboard channel
swaps can be noticed randomly.
Increasing the SGTL5000 LRCLK pad strength to its maximum value fixes
the issue, so add the 'lrclk-strength' property to avoid the audio
channel swaps.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add nodes to support the Controller Area Network(M_CAN) on SAMA5D2.
The version of M_CAN IP core is 3.1.0 (CREL = 0x31040730).
As said in SAMA5D2 datasheet, the CAN clock is recommended to use
frequencies of 20, 40 or 80 MHz. To achieve these frequencies,
PMC GCLK3 must select the UPLLCK(480 MHz) as source clock and
divide by 24, 12, or 6. So, the "assigned-clock-rates" property
has three options: 20000000, 40000000, and 80000000.
The "assigned-clock-parents" property should be referred to utmi
fixedly.
The MSBs [bits 31:16] of the CAN Message RAM for CAN0 and CAN1 are
default configured in 0x00200000. To avoid conflict with SRAM map
for PM, change them to 0x00210000 in the AT91Bootstrap via setting
the CAN Memories Address-based Register(SFR_CAN) of SFR.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The aa104xd12 and aa121td01 panels are LVDS panels, not DPI panels.
Use the correct DT bindings.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The dock board of Lichee Pi Zero features a MicroSD slot on MMC1, which
can be used with a MicroSD card or the MicroSD-slot Wi-Fi card provided
by Lichee Pi Zero.
Add pinmux for the mmc1 controller, and specify it in the mmc1 device
node as it's the only pinmux for mmc1.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner V3s features a LRADC like the ones in older SoCs.
Add a device tree node for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All the used CCU definitions are stripped from the V3s DTSI file when
it's merged, as the DTSI file and the CCU device tree binding headers
went to different trees.
As they're all in Linus's tree now, restore the usage of the
definitions.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add Sean as one of the authors for the mt7623.dtsi
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add afe nodes to the mt7623.dtsi file. Which
is the necessary node for I2S audio in/out.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add crypto engine nodes to the mt7623.dtsi file.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add USB nodes to the mt7623.dtsi file.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add e/MMC nodes to the mt7623.dtsi file.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
