IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The cdce706 clkout clocks implements a mux with a set_parent hook, but
doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidate to
trigger that parent change is a call to clk_set_rate(), with
determine_rate() figuring out which parent is the best suited for a
given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The driver does implement round_rate() though, which means that we can
change the rate of the clock, but we will never get to change the
parent.
However, It's hard to tell whether it's been done on purpose or not.
Since we'll start mandating a determine_rate() implementation, let's
convert the round_rate() implementation to a determine_rate(), which
will also make the current behavior explicit. And if it was an
oversight, the clock behaviour can be adjusted later on.
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-52-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The cdce706 divider clocks implements a mux with a set_parent hook, but
doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidate to
trigger that parent change is a call to clk_set_rate(), with
determine_rate() figuring out which parent is the best suited for a
given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The driver does implement round_rate() though, which means that we can
change the rate of the clock, but we will never get to change the
parent.
However, It's hard to tell whether it's been done on purpose or not.
Since we'll start mandating a determine_rate() implementation, let's
convert the round_rate() implementation to a determine_rate(), which
will also make the current behavior explicit. And if it was an
oversight, the clock behaviour can be adjusted later on.
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-51-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The cdce706 "clkin" clock implements a mux with a set_parent hook, but
doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidates to
trigger that parent change are either the assigned-clock-parents device
tree property or a call to clk_set_rate(), with determine_rate()
figuring out which parent is the best suited for a given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
Similarly, it doesn't look like the device tree using that clock driver
uses any of the assigned-clock properties on that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the determine_rate
implementation to clk_hw_determine_rate_no_reparent(). Indeed, if no
determine_rate implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-12-971d5077e7d2@cerno.tech
| Reported-by: kernel test robot <lkp@intel.com>:
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230427125531.622202-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use the managed `devm_of_clk_add_hw_provider()` instead of
`of_clk_add_hw_provider()`.
This makes sure the provider gets automatically removed on unbind and
allows to completely eliminate the drivers `remove()` callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230410014502.27929-4-lars@metafoo.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i2c probe function here doesn't use the id information provided in
its second argument, so the single-parameter i2c probe function
("probe_new") can be used instead.
This avoids scanning the identifier tables during probes.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20220407151831.2371706-2-steve@sk2.org
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200703175114.15027-1-grandmaster@al2klimov.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
side. The two main highlights in the core framework are the addition of an bulk
clk_get API that handles optional clks and an extra debugfs file that tells the
developer about the current parent of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is mostly
because that SoC has started converting to the clk_hw style of clk
registration. The next big update is in the Amlogic meson clk driver that
gained some support for audio, cpu, and temperature clks while fixing some PLL
issues. Finally, the biggest thing that stands out is the conversion of a large
part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses
less strings and more pointer comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks here and
there to clk data along with the normal addition of a handful of new drivers
and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1
-----BEGIN PGP SIGNATURE-----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=mK0C
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Mostly converted with the following snippet:
@@
struct clk_hw *E;
@@
-__clk_get_flags(E->clk)
+clk_hw_get_flags(E)
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This clock provider uses the consumer API, so include clk.h
explicitly.
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Remove a previously registered clock provider when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The array of parent names can be made as array of const pointers to
const strings.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The driver allows using CDCE706 in its default configuration recorded in
EEPROM and adjusting of synthesized clocks by consumers.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
