IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Instead of waiting for BTM indication we should wait for preboot ready.
Consider the below scenario:
1. FW update is being triggered
- setting the dirty bit
2. hard reset will be triggered due to the dirty bit
3. FW initiates the reset:
- dirty bit cleared
- BTM indication cleared
- preboot ready indication cleared
4. during hard reset:
- BTM indication will be set
- BIST test performed and another reset triggered
5. only after this reset the preboot will set the preboot ready
When polling on BTM indication alone we can lose sync with FW while
trying to communicate with FW that is during reset.
To overcome this we will always wait to preboot ready indication.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Need to put fences even if an unexpected status value is received while
waiting for a fence.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The -ERESTARTSYS return value is not handled correctly when a signal is
received while waiting for CS completion.
This can lead to bad output values to user when waiting for a single CS
completion, and more severe, it can cause a non-stopping loop when
waiting to multi-CS completion and until a CS timeout.
Fix the handling and exit the waiting if this return value is received.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This patch fixes a bug that was found in the dmabuf flow.
Bug description as found on Gaudi2 device:
1. User allocates 4MB of device memory
- Note that although the allocation size was 4MB the HMMU allocated
a full page of 768MB to back the request.
- The user gets a memory handle that points to a single page (768MB)
- Mapping the handle, the user gets virtual address to the start of
the page.
2. User exports the buffer
3. User registers the exported buffer in the importer. This flow has
a callback to the exporter which in turn converts the phys_page_pack
to an SG list for the importer. This SG list is of single entry of
size 768MB. However, the size that was passed to the importer was
only 4MB.
The solution for this is to make sure the importer gets exposure only
to the exported size.
This will be done by fixing the SG created by the exporter to be of
the total size of the actual exported memory requested by the user.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
A previous commit deprecated the option to export from handle, leaving
the code with no support for devices with virtual memory.
This commit modifies the export API in a way that unifies the uAPI to
user address for both cases (i.e. with and without MMU support) and add
the actual support for devices with virtual memory.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Validate export parameters in a dedicated function instead of in the
main export flow.
This will be useful later when support to export dmabuf for devices
with virtual memory will be added.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The API to the user which allows exporting DMA buffer from handle is
deprecated here. It was never used as it is relevant only for Gaudi2,
and the user stack has yet to add support for dmabuf in Gaudi2.
Looking forward, a modified API to export DMA buffer for ASICs that
supports virtual memory will be added.
Until the new API will be ready- exporting DMA buffer will not be
supported for ASICs with virtual memory.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This warning doesn't have real consequences, and therefore can be
printed in debug level.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Call COMMS tracepoints from within the dynamic CPU FW load.
This can help debug failures or delays in the dynamic FW load flow.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As the COMMS protocol is being used more widely in our driver,
an available debug tool for the handshake will be handy.
This commit defines tracepoints to various key points of the COMMS
protocol.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In certain scenarios, firmware might encounter a fatal event for
which a device reset is required. Hence, a proper notification
is needed for driver to be aware and initiate a reset sequence.
In secured environments the reset will be performed by firmware
without an explicit request from the driver.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When user context is released and hpriv_release() is called, there is a
device idle status check, to understand if user has left the device not
idle and then a reset is required.
However, if the user process is killed because of device hard reset,
the device at this point would always be not idle, because the device
engines were already forcefully halted.
Modify hpriv_release() to skip the idle check if reset is in progress.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
timestamp events that expire on the same interrupt will get the same
timestamp value
Signed-off-by: Tamir Gilad-Raz <tgiladraz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to reduce error log, we try to minimize the dumped rows
while keeping all relevant error info. In addition we completely
remove clock throttling debug logs.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
During event handling we extract interrupt cause and count it.
In case we could not find any cause we should add proper error.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
If the f/w reports the binning masks at the preboot stage, the driver
must align its DRAM properties according to the new information.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Removing double assignment of the hop2_pte_addr
variable in dram_default_mapping_fini().
Dead store reported by clang-analyzer.
Signed-off-by: Marco Pagani <marpagan@redhat.com>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As ASICs are evolving, we will need to update the DRAM properties at
various points because we may get different information from the f/w
at different points of the initialization.
This ASIC function is a foundation for this capability.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As hl_mmap_mem_buf_get() is called also from IOCTLs which can have a
bad handle from user, modify the print for "no match to handle" to use
dev_dbg().
Calls to this function which are not dependent on user, already have an
error print when the function fails.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The refcount of a CB buffer is initialized when user allocates a CB,
and is decreased when he destroys the CB handle.
If this refcount is increased also from kernel and user sends more than
one destroy requests for the handle, the buffer will be released/freed
and later be accessed when the refcount is put from kernel side.
To avoid it, prevent user from destroying the handle more than once.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As clock throttling due to high power consumption can happen very
frequently and there is no real reason to notify the user about it,
we skip this notification in all asics.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
User should close the FD when being notified about an error, after
which a device reset takes place.
However, if the user has pending threads that wait for completions,
the device release won't be called and eventually the watchdog timeout
will expire, leading to hard reset and killing the user process.
To avoid it, abort such waiting threads right after the error
notification, and block following waiting operations.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The device file is not in use when hl_device_release() is called,
and there aren't any user threads that use IOCTLs to wait for
interrupts. Therefore there is no need to release them at this point.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Sometimes we need the binning info at a very early state of the
driver initialization. Therefore, support was added in preboot to
provide the binning info as part of the f/w descriptor and the driver
can now use that.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Fix programming incorrect value of address range
Signed-off-by: tal albo <talbo@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The generic fbdev emulation names variables of type struct fb_info
both 'fbi' and 'info'. The latter seems to be more common in fbdev
code, so name fbi accordingly.
Also replace the duplicate variable in drm_fbdev_fb_destroy().
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125200415.14123-11-tzimmermann@suse.de
The fbdev framebuffer cleanup in drm_fbdev_fb_destroy() calls
drm_fbdev_release() and drm_fbdev_cleanup(). Inline both into the
caller. No functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125200415.14123-10-tzimmermann@suse.de
For uninitialized framebuffers, only release the DRM client and
free the fbdev memory. Do not attempt to clean up the framebuffer.
DRM fbdev clients have a two-step initialization: first create
the DRM client; then create the framebuffer device on the first
successful hotplug event. In cases where the client never creates
the framebuffer, only the client state needs to be released. We
can detect which case it is, full or client-only cleanup, by
looking at the presence of fb_helper's info field.
v3:
* fix typo in commit message (Javier)
* release client before unpreparing fbdev
v2:
* remove test for (fbi != NULL) in drm_fbdev_cleanup() (Sam)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125200415.14123-9-tzimmermann@suse.de
Call drm_fb_helper_fini() in the generic-fbdev hotplug helper
to revert the effects of drm_fb_helper_init(). No full cleanup
is required.
v3:
* fix error in commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125200415.14123-8-tzimmermann@suse.de
Initialize the fb-helper's preferred_bpp field early from within
drm_fb_helper_prepare(); instead of the later client hot-plugging
callback. This simplifies the generic fbdev setup function.
No real changes, but all drivers' fbdev code has to be adapted.
v3:
* build with CONFIG_DRM_FBDEV_EMULATION unset (kernel test bot)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125200415.14123-7-tzimmermann@suse.de
Store the console's preferred BPP value in struct drm_fb_helper
and remove the respective function parameters from the internal
fbdev code.
The BPP value is only required as a fallback and will now always
be available in the fb-helper instance.
No functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125200415.14123-6-tzimmermann@suse.de
Initialize the fb-helper structure immediately after its allocation
in drm_fbdev_generic_setup(). That will make it easier to fill it with
driver-specific values, such as the preferred BPP.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125200415.14123-5-tzimmermann@suse.de
Signal failed hotplugging with a flag in struct drm_client_dev. If set,
the client helpers will not further try to set up the fbdev display.
This used to be signalled with a combination of cleared pointers in
struct drm_fb_helper, which prevents us from initializing these pointers
early after allocation.
The change also harmonizes behavior among DRM clients. Additional DRM
clients will now handle failed hotplugging like fbdev does.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125200415.14123-3-tzimmermann@suse.de
Test for connectors in the client code and remove a similar test
from the generic fbdev emulation. Do nothing if the test fails.
Not having connectors indicates a driver bug.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125200415.14123-2-tzimmermann@suse.de
Force the internal PHY off then on when switching to the internal path.
This fixes problems where the PHY ID is not properly set.
Fixes: 7090425104db ("net: phy: add amlogic g12a mdio mux support")
Suggested-by: Qi Duan <qi.duan@amlogic.com>
Co-developed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20230124101157.232234-1-jbrunet@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netif_stop_queue() and netif_wake_queue() act on TX queue 0. This is ok
as long as only a single TX queue is supported. But support for multiple
TX queues was introduced with 762031375d5c and I missed to adapt stop
and wake of TX queues.
Use netif_stop_subqueue() and netif_tx_wake_queue() to act on specific
TX queue.
Fixes: 762031375d5c ("tsnep: Support multiple TX/RX queue pairs")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://lore.kernel.org/r/20230124191440.56887-1-gerhard@engleder-embedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During EEH error injection testing, a deadlock was encountered in the tg3
driver when tg3_io_error_detected() was attempting to cancel outstanding
reset tasks:
crash> foreach UN bt
...
PID: 159 TASK: c0000000067c6000 CPU: 8 COMMAND: "eehd"
...
#5 [c00000000681f990] __cancel_work_timer at c00000000019fd18
#6 [c00000000681fa30] tg3_io_error_detected at c00800000295f098 [tg3]
#7 [c00000000681faf0] eeh_report_error at c00000000004e25c
...
PID: 290 TASK: c000000036e5f800 CPU: 6 COMMAND: "kworker/6:1"
...
#4 [c00000003721fbc0] rtnl_lock at c000000000c940d8
#5 [c00000003721fbe0] tg3_reset_task at c008000002969358 [tg3]
#6 [c00000003721fc60] process_one_work at c00000000019e5c4
...
PID: 296 TASK: c000000037a65800 CPU: 21 COMMAND: "kworker/21:1"
...
#4 [c000000037247bc0] rtnl_lock at c000000000c940d8
#5 [c000000037247be0] tg3_reset_task at c008000002969358 [tg3]
#6 [c000000037247c60] process_one_work at c00000000019e5c4
...
PID: 655 TASK: c000000036f49000 CPU: 16 COMMAND: "kworker/16:2"
...:1
#4 [c0000000373ebbc0] rtnl_lock at c000000000c940d8
#5 [c0000000373ebbe0] tg3_reset_task at c008000002969358 [tg3]
#6 [c0000000373ebc60] process_one_work at c00000000019e5c4
...
Code inspection shows that both tg3_io_error_detected() and
tg3_reset_task() attempt to acquire the RTNL lock at the beginning of
their code blocks. If tg3_reset_task() should happen to execute between
the times when tg3_io_error_deteced() acquires the RTNL lock and
tg3_reset_task_cancel() is called, a deadlock will occur.
Moving tg3_reset_task_cancel() call earlier within the code block, prior
to acquiring RTNL, prevents this from happening, but also exposes another
deadlock issue where tg3_reset_task() may execute AFTER
tg3_io_error_detected() has executed:
crash> foreach UN bt
PID: 159 TASK: c0000000067d2000 CPU: 9 COMMAND: "eehd"
...
#4 [c000000006867a60] rtnl_lock at c000000000c940d8
#5 [c000000006867a80] tg3_io_slot_reset at c0080000026c2ea8 [tg3]
#6 [c000000006867b00] eeh_report_reset at c00000000004de88
...
PID: 363 TASK: c000000037564000 CPU: 6 COMMAND: "kworker/6:1"
...
#3 [c000000036c1bb70] msleep at c000000000259e6c
#4 [c000000036c1bba0] napi_disable at c000000000c6b848
#5 [c000000036c1bbe0] tg3_reset_task at c0080000026d942c [tg3]
#6 [c000000036c1bc60] process_one_work at c00000000019e5c4
...
This issue can be avoided by aborting tg3_reset_task() if EEH error
recovery is already in progress.
Fixes: db84bf43ef23 ("tg3: tg3_reset_task() needs to use rtnl_lock to synchronize")
Signed-off-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230124185339.225806-1-drc@linux.vnet.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When user switch samba to ksmbd, The following message flood is coming
when accessing files. Samba seems to changs dos attribute version to v5.
This patch downgrade ndr version error message to debug.
$ dmesg
...
[68971.766914] ksmbd: v5 version is not supported
[68971.779808] ksmbd: v5 version is not supported
[68971.871544] ksmbd: v5 version is not supported
[68971.910135] ksmbd: v5 version is not supported
...
Cc: stable@vger.kernel.org
Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3")
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stream protocol length will never be larger than 16KB until session setup.
After session setup, the size of requests will not be larger than
16KB + SMB2 MAX WRITE size. This patch limits these invalidly oversized
requests and closes the connection immediately.
Fixes: 0626e6641f6b ("cifsd: add server handler for central processing and tranport layers")
Cc: stable@vger.kernel.org
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-18259
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
The cxl_pmem.ko module houses the driver for both cxl_nvdimm_bridge
objects and cxl_nvdimm objects. When the core creates a cxl_nvdimm it
arranges for it to be autoremoved when the bridge goes down. However, if
the bridge never initialized because the cxl_pmem.ko module never
loaded, it sets up a the following crash scenario:
BUG: kernel NULL pointer dereference, address: 0000000000000478
[..]
RIP: 0010:cxl_nvdimm_probe+0x99/0x140 [cxl_pmem]
[..]
Call Trace:
<TASK>
cxl_bus_probe+0x17/0x50 [cxl_core]
really_probe+0xde/0x380
__driver_probe_device+0x78/0x170
driver_probe_device+0x1f/0x90
__driver_attach+0xd2/0x1c0
bus_for_each_dev+0x79/0xc0
bus_add_driver+0x1b1/0x200
driver_register+0x89/0xe0
cxl_pmem_init+0x50/0xff0 [cxl_pmem]
It turns out the recent rework to simplify nvdimm probing obviated the
need to unregister cxl_nvdimm objects at cxl_nvdimm_bridge ->remove()
time. Leave the cxl_nvdimm device registered until the hosting
cxl_memdev departs. The alternative is that the cxl_memdev needs to be
reattached whenever the cxl_nvdimm_bridge attach state cycles, which is
awkward and unnecessary.
The only requirement is to make sure that when the cxl_nvdimm_bridge
goes away any dependent cxl_nvdimm objects are shutdown. Handle that in
unregister_nvdimm_bus().
With these registration entanglements removed there is no longer a need
to pre-load the cxl_pmem module in cxl_acpi.
Fixes: cb9cfff82f6a ("cxl/acpi: Simplify cxl_nvdimm_bridge probing")
Reported-by: Gregory Price <gregory.price@memverge.com>
Debugged-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/167426077263.3955046.9695309346988027311.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The current design of callback function disable() of struct
nvkm_devinit_func is defined to return a u64 value. In its implementation
in the driver modules, the function always returns a fixed value 0. Hence
the design and implementation of this function should be enhanced to return
void instead of a fixed value. This change also eliminates untouched
return variables.
The change is identified using the returnvar.cocci Coccinelle semantic
patch script.
Signed-off-by: Deepak R Varma <drv@mailo.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Y9FFoooIXjlr+UP1@ubun2204.myguest.virtualbox.org
struct bkey has internal padding in a union, but it isn't always named
the same (e.g. key ## _pad, key_p, etc). This makes it extremely hard
for the compiler to reason about the available size of copies done
against such keys. Use unsafe_memcpy() for now, to silence the many
run-time false positive warnings:
memcpy: detected field-spanning write (size 264) of single field "&i->j" at drivers/md/bcache/journal.c:152 (size 240)
memcpy: detected field-spanning write (size 24) of single field "&b->key" at drivers/md/bcache/btree.c:939 (size 16)
memcpy: detected field-spanning write (size 24) of single field "&temp.key" at drivers/md/bcache/extents.c:428 (size 16)
Reported-by: Alexandre Pereira <alexpereira@disroot.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216785
Acked-by: Coly Li <colyli@suse.de>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: linux-bcache@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230106060229.never.047-kees@kernel.org
Since the long memcpy tests may stall a system for tens of seconds
in virtualized architecture environments, split those tests off under
CONFIG_MEMCPY_SLOW_KUNIT_TEST so they can be separately disabled.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/lkml/20221226195206.GA2626419@roeck-us.net
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: David Gow <davidgow@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
[Why&How]
Switching between certain modes that are freesync video modes and those
are not freesync video modes result in timing not changing as seen by
the monitor due to incorrect timing being driven.
The issue is fixed by ensuring that when a non freesync video mode is
set, we reset the freesync status on the crtc.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
We still need to refer to port while removing payload at commit_tail.
we should keep the kref till then to release.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2171
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Fixes: 4d07b0bc4034 ("drm/display/dp_mst: Move all payload info into the atomic state")
Cc: stable@vger.kernel.org # 6.1
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Tested-by: Didier Raboud <odyx@debian.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
