IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Analog Device codecs seem to have problems with the triggering of
pin-sensing although their pincaps give the trigger requirements.
Some reported that constant CPU load on HP laptops with AD codecs.
For avoiding this regression, add a flag to codec struct to notify
explicitly that the codec doesn't suppot the trigger at pin-sensing.
Tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we run the following commands in turn (with
CONFIG_SND_HDA_POWER_SAVE_DEFAULT=0),
speaker-test -Dhw:0,3 -c2 -twav # HDMI
speaker-test -Dhw:0,0 -c2 -twav # Analog
The second command will produce sound in the analog lineout _as well as_
HDMI sink. The root cause is, device 0 "reuses" the same stream tag that
was used by device 3, and the "intelhdmi - sticky stream id" patch leaves
the HDMI codec in a functional state. So the HDMI codec happily accepts
the audio samples which reuse its stream tag.
The proposed solution is to remember the last device each azx_dev was
assigned to, and prefer to
1) reuse the azx_dev (and hence the stream tag) the HDMI codec last used
2) or assign a never-used azx_dev for HDMI
With this patch and the above two speaker-test commands,
HDMI codec will use stream tag 8 and Analog codec will use 5.
The stream tag used by HDMI codec won't be reused by others, as long
as we don't run out of the 4 playback azx_dev's. The legacy Analog
codec will continue to use stream tag 5 because its device id is 0
(this is a bit tricky).
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sevelar ASoC codec drivers wrongly assume, that the params_rate() macro
returns one of SNDRV_PCM_RATE_* defines instead of the actual numerical
sampling rate. Fix them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
I2C devices should be registered when platform board setting
in latest ASoC.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes a bug where "virtual" registers were being written to the ac97
bus. This was causing unrelated registers to become corrupted (headphone 0x04,
touchscreen 0x78, etc).
This patch duplicates protection that was included in the wm9713 driver.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Postpone the mixer name setup after the codec patch since the codec
patch may change the codec name string in itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the wrong implementation of NID <-> kctl mapping for capture mixers
introduced by the ocmmit 5b0cb1d850.
So far, the driver returns an error at probe.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 2ccafed4 added an extra parameter to the DAI .set_pll() method, but
it missed this call in sound/soc/imx/mx27vis_wm8974.c.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
platform_get_irq returns -ENXIO on failure, so !irq was probably
always true. Better use (int)irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
This is a followup to 305b3228f9 that
changed the return value of platform_get_irq from 0 to -ENXIO on error.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A machine with AMD CPU with Nvidia board doesn't work with MSI.
Reported-by: Robert J. King <peritus@gurunetwork.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With the attached patch I am able to use the sound on a new IMac 27.
What works:
*) Internal speakers
*) Internal microphone
*) Headphone
I don't have an external mic or a SPDIF device to test the rest.
Signed-off-by: Rafael Avila de Espindola <rafael.espindola@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Memory amount is increased before a successful write-read
sequence is done. Thus, 512 kB of onboard memory is detected
on memoryless cards like SB32.
Move the increasing of memory counter after successful read
is done.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The direction of rounding is incorrect in the snd_interval_ratnum()
It was detected with following parameters (sb8 driver playing
8kHz stereo file):
- num is always 1000000
- requested frequency rate is from 7999 to 7999 (single frequency)
The first loop calculates div_down(num, freq->min) which is 125.
Thus, a frequency range's minimum value is 1000000 / 125 = 8000 Hz.
The second loop calculates div_up(num, freq->max) which is 126
The frequency range's maximum value is 1000000 / 126 = 7936 Hz.
The range maximum is lower than the range minimum so the function
fails due to empty result range.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current Realtek code makes no specific provision for turning stuff
off. The codec chip is placed into low-power mode generically, but this
doesn't turn off any external hardware connected to it, in particular
external amplifiers.
This patch creates a hook function that is called by the codec
suspend/resume functions. It ought to disable any external hardware in a
device-specific way. I've implemented a generic ALC889 function that
sets the EAPD pin properly, and used it for the Acer Aspire 8930G which
can benefit from this feature.
On my laptop, this results in ~0.5W extra savings.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes some extra mixers that do nothing on the Acer Aspire
8930G.
The CD mixer is useless because the SATA DVD/Blu-Ray drive has no analog
audio output, and the Side mixer is useless because we max out at 6ch
anyway.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch just simplifies the 8930G verb array a bit. Just use the
common ALC889 EAPD verb array to make things more consistent. The file
is already huge enough already.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://bugs.launchpad.net/bugs/479373
The OR has verified with hda-verb that the internal microphone needs
VREF50 set for audible capture.
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We can use finer-grained locking, which makes things easier when
we gain DMA support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the recording and playback paths are now the same, eliminate
the needless conditionals.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There's no need for a specific rule; ALSA's generic AC'97 support
calculates the necessary rate constraint information itself, and
we can use this directly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of listing all individual PCI IDs, check the matching with
the PCI class together with the vendor id for Nvidia.
This simplifies the pci id entries.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The wm8974 datasheet defines BUFIOEN as bit 2.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
When allocating the PCM buffer, use vmalloc_user() instead of vmalloc().
Otherwise, it would be possible for applications to play the previous
contents of the kernel memory to the speakers, or to read it directly if
the buffer is exported to userspace.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some model quirks missed the corresponding capsrc_nids. This resulted in
non-working capture source selection.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Conexant CX20583-10Z has digital beep device with volume control.
Making use of them.
Signed-off-by: Einar Rünkaru <einarry@smail.ee>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed initialization of internal mic and added internal mic boost control
Renamed analog mic boost control to ext mic boost contol.
Name pair analog/digital seems too confusing for a normal user.
Signed-off-by: Einar Rünkaru <einarry@smail.ee>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
1. Add more ASUS NB model.
2. Fixed alc663_m51va_setup
M51VA has Digital Mic that NID is 0x12. The record source index is
0x9 for ALC663.
So, to modify the alc663_m51va_setup function to index 0x9
and add analog Mic aupport function alc663_mode1_setup.
3. Add ASUS mode7 and mode8 modules for ALC663
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recent drivers/mfd/twl4030* renames to twl broke compile for
various boards as the series was missing a patch to change
the board-*.c files.
This patch renames include twl4030.h to include twl.h
and also renames twl4030_i2c_ routines.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change code so that switching to playing music through the analog output
disables SPDIF out instead of disabling it when stream ends.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ac97_codec - increase timeout for analog sections to 5 second
ASoC: Correct code taking the size of a pointer
ALSA: hda - Add PCI IDs for Nvidia G2xx-series
ALSA: sound/isa/gus: Correct code taking the size of a pointer
ALSA: hda: Fix max PCM level to 0 dB for AD1981_HP
ALSA: hda: Use ALC260_WILL quirk for another Acer model (0x1025007f)
Makes use of skip_spaces() defined in lib/string.c for removing leading
spaces from strings all over the tree.
It decreases lib.a code size by 47 bytes and reuses the function tree-wide:
text data bss dec hex filename
64688 584 592 65864 10148 (TOTALS-BEFORE)
64641 584 592 65817 10119 (TOTALS-AFTER)
Also, while at it, if we see (*str && isspace(*str)), we can be sure to
remove the first condition (*str) as the second one (isspace(*str)) also
evaluates to 0 whenever *str == 0, making it redundant. In other words,
"a char equals zero is never a space".
Julia Lawall tried the semantic patch (http://coccinelle.lip6.fr) below,
and found occurrences of this pattern on 3 more files:
drivers/leds/led-class.c
drivers/leds/ledtrig-timer.c
drivers/video/output.c
@@
expression str;
@@
( // ignore skip_spaces cases
while (*str && isspace(*str)) { \(str++;\|++str;\) }
|
- *str &&
isspace(*str)
)
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Cc: Julia Lawall <julia@diku.dk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously, OLPC support for the mic extensions was only enabled in the
ALSA driver if CONFIG_OLPC and CONFIG_MGEODE_LX were both set. This was
because the old geode GPIO code was written in a manner that assumed
CONFIG_MGEODE_LX. With the new cs553x-gpio driver, this is no longer the
case; as such, we can drop the requirement on CONFIG_MGEODE_LX and instead
include a requirement on GPIOLIB.
We use the generic GPIO API rather than the cs553x-specific API.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If ak4642 driver was compiled without I2C configs,
ak4642_modinit return value will become un-stable.
This patch modify this bug
Reported-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The HDA_SUBDEV_NID_FLAG is duplicate for amplifier control elements. Move
get_amp_nid_() call to the snd_hda_ctl_add() function.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The purpose of this changeset is to show information about amplifier
setting in the codec proc file. Something like:
Control: name="Front Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Control: name="Front Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=2, ofs=0
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This set of changes add missing NID values to some static control
elemenents. Also, it handles all "Capture Source" or "Input Source"
controls.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
I have a Soundblaster 16PCI. For many years, alsa has had a bug where
not all of the card's controls are detected (many alsa versions,
many kernel versions). In particular, Master Playback Volume is
usually not detected, and so I get no sound or extremely faint sound.
The problem has always been inconsistent: sometimes all of the controls
are detected correctly, and sometimes a partial set is detected. It works
correctly about 10% of the time.
Finally, I got around to tracking down the problem. When the driver
fails, it prints the kernel message "AC'97 0 analog subsections not
ready". This message is generated from the function snd_ac97_mixer()
in ac97_codec.c. The message indicates that the card failed to come
back after reset within the time limit. The time limit is
120 milliseconds.
I tried increasing the time limit to 1 second, and found that this
made the driver work about 70% of the time. I tried increasing it
to 5 seconds, and it now seems to work 100% of the time.
I expect that this change would be completely harmless for
existing cards that work, and would only introduce additional
delay for cards that do not work.
ALSA bug#4032.
Signed-off-by: Steve Soule <sts11dbxr@gmail.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
sizeof(codec->reg_cache) is just the size of the pointer. Elsewhere in the
file, codec->reg_cache is used with sizeof(wm8900_reg_defaults), so the
code is changed to do the same here.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sizeof(share_id) is just the size of the pointer. On the other hand,
block->share_id is an array, so its size seems more appropriate.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://bugs.launchpad.net/bugs/461062
The original reporter states that PCM maxes at +12 dB and results in
very bad distortion. Cap PCM at 0 dB to resolve this symptom.
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://bugs.launchpad.net/bugs/418627
The original reporter states that this quirk is necessary to obtain
reasonable gain for playback. Without it, sound is inaudible. Tested
with playback (spkr and hp) and capture.
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Bring the WM8350 IRQ API more in line with the generic IRQ API by
masking and unmasking interrupts as they are requested and freed.
This is mostly just a case of deleting the mask and unmask calls
from the individual drivers.
The RTC driver is changed to mask the periodic IRQ after requesting
it rather than only unmasking the alarm IRQ. If the periodic IRQ
fires in the period where it is reqested then there will be a
spurious notification but there should be no serious consequences
from this.
The CODEC drive is changed to explicitly disable headphone jack
detection prior to requesting the IRQs. This will avoid the IRQ
firing with no jack set up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is done as simple code transformation, the semantics of the
IRQ API provided by the core are are still very different to those
of genirq (mainly with regard to masking).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Overwrite pin config on intel DG45ID board.
intelhdmi - dont power off HDA link
ALSA: hrtimer - Fix lock-up
ALSA: intelhdmi - add channel mapping for typical configurations
ALSA: intelhdmi - channel mapping applies to Pin
ALSA: intelhdmi - accept DisplayPort pin
ALSA: hda - show HBR(High Bit Rate) pin cap in procfs
ALSA: hda - Fix LED GPIO setup for HP laptops with IDT codecs
ASoC: Fix build of OMAP sound drivers
ALSA: opti93x: fix irq releasing if the irq cannot be allocated
The pin config provided by BIOS have some problems:
0x0221401f: [Jack] HP Out at Ext Front <-- other association and sequence
0x02a19020: [Jack] Mic at Ext Front <-- other association
0x01113014: [Jack] Speaker at Ext Rear <-- line out (not speaker)
0x01114010: [Jack] Speaker at Ext Rear <-- line out
0x01a19030: [Jack] Mic at Ext Rear <-- other association
0x01111012: [Jack] Speaker at Ext Rear <-- line out
0x01116011: [Jack] Speaker at Ext Rear <-- line out
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x01451140: [Jack] SPDIF Out at Ext Rear
0x40f000f0: [N/A] Other at Ext N/A
just overwrite it.
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For codecs without EPSS support (G45/IbexPeak), the hotplug event will
be lost if the HDA is powered off during the time. After that the pin
presence detection verb returns inaccurate info.
So always power-on HDA link for !EPSS codecs.
KarL offers the fact and Takashi recommends to flag hda_bus. Thanks!
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The timer stop callback can be called from snd_timer_interrupt(), which
is called from the hrtimer callback. Since hrtimer_cancel() waits for
the callback completion, this eventually results in a lock-up.
This patch fixes the problem by just toggling a flag at stop callback
and call hrtimer_cancel() later.
Reported-and-tested-by: Wojtek Zabolotny <W.Zabolotny@elka.pw.edu.pl>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
IbexPeak is the first Intel HDMI audio codec to support channel mapping.
Currently the outstanding problem is, the HDMI channel order do not
agree with that of ALSA. This patch presents workaround for some
typical use cases. It gives priority to the typical ALSA surround
configurations, and defines channel mapping for them.
We may need better kernel+userspace interactive channel mapping scheme.
For example, in current scheme if user plays with the surround50 device,
the kernel is unaware of this and will still select the surround41
channel allocation and channel mapping..
Thanks to Marcin for offering good tips!
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA036-A specifies that the Audio Sample Packet (ASP) Channel Mapping
verbs apply to Digital Display Pin Complex instead of Converter.
With this fix, channel mapping is working as expected for IbexPeak.
Thanks to Marcin for pointing this out!
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA036 spec states:
DP (Display Port) indicates whether the Pin Complex Widget supports
connection to a Display Port sink. Supported if set to 1. Note that
it is possible for the pin widget to support more than one digital
display connection type, e.g. HDMI and DP bit are both set to 1.
Also export the DP pin cap in procfs.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Note that the HBR capability only applies to HDMI pin.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes an error in processing of the HP BIOS configuration to enable
GPIO based mute LED indicator control. That error causes driver to enable
such control on all HP systems with the 92HD75 IDT codecs and results in
unnecessary toggling of the GPIO on mute control manipulation.
It also adds support of the future HP BIOS configuration extension for the
named control. New configuration string has a format HP_Mute_LED_P_G
where P can be 0 or 1 and defines mute LED GPIO control state (low/high)
that corresponds to the NOT muted state of the master volume
and G is the index of the GPIO to use (0..9)
Lastly, it adds more systems to the support of the audio implementation
as found on HP B-series systems
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are build errors when building for some of the omap2/3 boards without
enabling sound:
sound/built-in.o:(.data+0x43bc): undefined reference to `soc_codec_dev_tlv320aic23'
sound/built-in.o:(.data+0x43cc): undefined reference to `tlv320aic23_dai'
Confused me quite a bit since the drivers that had references to the
codec weren't enabled. Turns out the Makefile was using the wrong
config option to enable them. Patch below.
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While Linux provided an O_SYNC flag basically since day 1, it took until
Linux 2.4.0-test12pre2 to actually get it implemented for filesystems,
since that day we had generic_osync_around with only minor changes and the
great "For now, when the user asks for O_SYNC, we'll actually give
O_DSYNC" comment. This patch intends to actually give us real O_SYNC
semantics in addition to the O_DSYNC semantics. After Jan's O_SYNC
patches which are required before this patch it's actually surprisingly
simple, we just need to figure out when to set the datasync flag to
vfs_fsync_range and when not.
This patch renames the existing O_SYNC flag to O_DSYNC while keeping it's
numerical value to keep binary compatibility, and adds a new real O_SYNC
flag. To guarantee backwards compatiblity it is defined as expanding to
both the O_DSYNC and the new additional binary flag (__O_SYNC) to make
sure we are backwards-compatible when compiled against the new headers.
This also means that all places that don't care about the differences can
just check O_DSYNC and get the right behaviour for O_SYNC, too - only
places that actuall care need to check __O_SYNC in addition. Drivers and
network filesystems have been updated in a fail safe way to always do the
full sync magic if O_DSYNC is set. The few places setting O_SYNC for
lower layers are kept that way for now to stay failsafe.
We enforce that O_DSYNC is set when __O_SYNC is set early in the open path
to make sure we always get these sane options.
Note that parisc really screwed up their headers as they already define a
O_DSYNC that has always been a no-op. We try to repair it by using it for
the new O_DSYNC and redefinining O_SYNC to send both the traditional
O_SYNC numerical value _and_ the O_DSYNC one.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Use the chip->irq to check if the irq should be released so the irq is not released
if it has not been allocated.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The volume levels in original implementation are incorrect and does
not match the dB scale. The real range is linear (in the sense of
the dB scale) from 0dB to -100dB. Remove logaritmic table and make
all volumes from range 0dB..100dB.
The tests are in RedHat's bugzilla #540817.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Quirk for the ALC662 found on the Intel D945GCLF2 (and possibly other)
mainboards.
Signed-off-by: David Santinoli <david@santinoli.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Confirmed from vendor and tests in RedHat bugzilla #536782 .
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The wrong variable was returned in the case of an error
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I added the product IDs of the new revisions of the devices, so owners
can test whether this suffices to make them work. Patched against ALSA
snapshot 20091207.
Signed-off-by: Tobias Hansen <Tobias.Hansen at physik.uni-hamburg.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On Realtek codecs, a digital mic pin is connected often only to a single
ADC. But the parser tries to set up all ADCs no matter whether the
digital mic is available, and results in non-selectable input source.
This patch adds a check of input-source availability of each ADC, and
excludes ones that don't support all input sources.
Reference: Novell bnc#561235
http://bugzilla.novell.com/show_bug.cgi?id=561235
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is an updated patch for the Apple iMac 9,1 model to add sound.
Original patch posted here:
http://article.gmane.org/gmane.linux.alsa.devel/61361/match=
I have been using this patch for a while now
and have to say it works vary well, except for a few minor
things:
With the iMac 24-inch 3.06GHz Intel Core 2 Duo
everything seems to be working as it should,
although I have not looked into the microphone
(never really use one, nor have any apps to test,
my guess is it doesn't work, or I never figured out how
to get it to work).
With the iMac 24-inch 2.66GHz Intel Core 2 Duo
everything is the same as with the above machine
except I'm hearing a light scratchy/distortion noise
come out of the speakers when using headphones(above machine
does not do this).
Other than that the sound level is great(especially with good Dj headphones).
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PnP data on the OPTI931 and OPTI933 contains io port
range for the MC indirect registers. Use the PnP range
instead of hardwired value 0xE0E.
Also, request region of MC indirect registers so it is
marked as used to other drivers (this was missing previously).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Komuro pointed out that IRQ_FIRST_SHARED is not used at all in the
PCMCIA subsystem, so remove it. Also, remove two bogus assignments.
CC: Karsten Keil <keil@b1-systems.de>
CC: netdev@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This renames from a character / to : of controls. A / occurs below error
messages.
ASoC: Failed to create IN2RP/VXRP debugfs file
ASoC: Failed to create IN2LP/VXRN debugfs file
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When primary AC97 is not found, don't fail with tons of AC97 errors.
Assume that the card is SF64-PCR (tuner-only).
This makes the SF64-PCR radio card work "out of the box".
Also fixes a bug that can cause an oops here:
if (tea575x_tuner > 0 && (tea575x_tuner & 0x000f) < 4) {
when tea575x_tuner == 16, it passes this check and causes problems
a couple lines below:
chip->tea.ops = &snd_fm801_tea_ops[(tea575x_tuner & 0x000f) - 1];
Tested with SF64-PCR, but I don't have any of those sound or sound+radio cards
to test if I didn't break anything.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix mute state reporting in tea575x-tuner.
This fixes mute function in kradio on SF64-PCR radio card.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
free the allocated pcm platform device in the error path.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
platform_device_unregister() frees resources for us, no need to
do it explicitly. Fixes an oops when machine code removes the
soc-audio device.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove snd_opti9xx fields which are indirect arguments to
the snd_opti9xx_configure(). Pass these values as function
arguments.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now snd_ac97_pcm_open() is called with the exactly same arguments
for both playback and capture directions. Remove the unneeded check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Muse Pocket use brocken mixer names, so alsamixer and PA can't use it correctly
This patch add quirk to overwirte default mixers.
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
FSC Amilo Pi 1505 has a buggy BIOS and doesn't set up the HP and
speaker pins properly. Add the pinfix entry for that.
Reference: Novell bnc#557403
https://bugzilla.novell.com/show_bug.cgi?id=557403
Signed-off-by: Takashi Iwai <tiwai@suse.de>
pcm->r[1].slots is the double rate slot information, not the
capture information. For capture, 'pcm' will already be the
capture ac97 pcm structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA's for-2.6.33 branch has a new source argument to
snd_soc_dai_set_pll().
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add support runtime PM.
Driver callbacks for Runtime PM are empty because
the device registers are always re-initialized after
pm_runtime_get_sync(). The Runtime PM functions replaces the
clock framework module stop bit handling in this driver.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PCM12 and PCM20 can be set into the ISA PnP mode. The PCM12 PnP
was sold as the PnP device.
Add code to handle detection of these cards using ISA PnP framework.
Tested on the PCM20 in PnP mode. The PCM12 PnP has the same MS Windows
INF file except for a card name displayed for user.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Separate common probing code in order to use it
for PnP probing.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most of the irq_req_t typedef'd struct can be re-worked quite
easily:
(1) IRQInfo2 was unused in any case, so drop it.
(2) IRQInfo1 was used write-only, so drop it.
(3) Instance (private data to be passed to the IRQ handler):
Most PCMCIA drivers using pcmcia_request_irq() to actually
register an IRQ handler set the "dev_id" to the same pointer
as the "priv" pointer in struct pcmcia_device. Modify the two
exceptions (ipwireless, ibmtr_cs) to also work this waym and
set the IRQ handler's "dev_id" to p_dev->priv unconditionally.
(4) Handler is to be of type irq_handler_t.
(5) Handler != NULL already tells whether an IRQ handler is present.
Therefore, we do not need the IRQ_HANDLER_PRESENT flag in
irq_req_t.Attributes.
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Jaroslav Kysela <perex@perex.cz>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Karsten Keil <isdn@linux-pingi.de>
for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes two issues:
a) Infinite loop in resume function
b) Writes to non-existing registers in resume function
Cc: stable@kernel.org
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit fe3e78e073
ASoC: Factor out snd_soc_init_card()
removed the error paths that are still valid for wm97* codecs, causing
the compile errors like
sound/soc/codecs/wm9705.c:399: error: label 'reset_err' used but not defined
sound/soc/codecs/wm9712.c:687: error: label 'reset_err' used but not defined
sound/soc/codecs/wm9713.c:1237: error: label 'reset_err' used but not defined
Revert the removed error path codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
STAC/IDT codecs seem to behave weird when SET_PIN_SENSE verb is issued
before reading the jack-detection although the TRIG_REQ pin capability
is given by the hardware.
Since snd_hda_jack_detect() issues the SET_PIN_SENSE verb simply judging
from the pincap, we have to revert the change in the commit
d56757abc1
ALSA: hda - Replace the rest of jack-detections with snd_hda_jack_detect()
to plain GET_PIN_SENSE verb without triggering.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
