IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
If the core soft reset timeout happens, avoid setting up event
buffers and starting gadget as the writes to these registers
may not reflect when in reset and setting the run stop bit
can lead the controller to access wrong event buffer address
resulting in a crash.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230510075252.31023-2-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cases where the controller somehow fails to write to event buffer
memory (e.g. due to incorrect MMU config), the driver would receive
all-zero dwc3 events. However, the abnormal event is silently dropped
as a regular ep0out event.
Add error logs when an unknown endpoint event is received to highlight
the anomaly.
Signed-off-by: Roy Luo <royluo@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230504000129.728316-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Realtek RTD SoCs were designed with the global register address
offset at 0x8100. The default address offset is constant at
DWC3_GLOBALS_REGS_START (0xc100). Therefore, add a check if the
compatible name of the parent is realtek,rtd-dwc3, then global
register start address will remap to 0x8100.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230505025104.18321-1-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several sequences utilize the same routine for forcing the control endpoint
back into the SETUP phase. This is required, because those operations need
to ensure that EP0 is back in the default state.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20230420212759.29429-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not call gadget stop until the poll for controller halt is
completed. DEVTEN is cleared as part of gadget stop, so the intention to
allow ep0 events to continue while waiting for controller halt is not
happening.
Fixes: c96683798e27 ("usb: dwc3: ep0: Don't prepare beyond Setup stage")
Cc: stable@vger.kernel.org
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20230420212759.29429-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was observed that there are hosts that may complete pending SETUP
transactions before the stop active transfers and controller halt occurs,
leading to lingering endxfer commands on DEPs on subsequent pullup/gadget
start iterations.
dwc3_gadget_ep_disable name=ep8in flags=0x3009 direction=1
dwc3_gadget_ep_disable name=ep4in flags=1 direction=1
dwc3_gadget_ep_disable name=ep3out flags=1 direction=0
usb_gadget_disconnect deactivated=0 connected=0 ret=0
The sequence shows that the USB gadget disconnect (dwc3_gadget_pullup(0))
routine completed successfully, allowing for the USB gadget to proceed with
a USB gadget connect. However, if this occurs the system runs into an
issue where:
BUG: spinlock already unlocked on CPU
spin_bug+0x0
dwc3_remove_requests+0x278
dwc3_ep0_out_start+0xb0
__dwc3_gadget_start+0x25c
This is due to the pending endxfers, leading to gadget start (w/o lock
held) to execute the remove requests, which will unlock the dwc3
spinlock as part of giveback.
To mitigate this, resolve the pending endxfers on the pullup disable
path by re-locating the SETUP phase check after stop active transfers, since
that is where the DWC3_EP_DELAY_STOP is potentially set. This also allows
for handling of a host that may be unresponsive by using the completion
timeout to trigger the stall and restart for EP0.
Fixes: c96683798e27 ("usb: dwc3: ep0: Don't prepare beyond Setup stage")
Cc: stable@vger.kernel.org
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20230413195742.11821-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting the PARKMODE_DISABLE_HS bit in the DWC3_USB3_GUCTL1.
When this bit is set to '1' all HS bus instances in park mode are disabled
For some USB wifi devices, if enable this feature it will reduce the
performance. Therefore, add an option for disabling HS park mode by
device-tree.
In Synopsys's dwc3 data book:
In a few high speed devices when an IN request is sent within 900ns of the
ACK of the previous packet, these devices send a NAK. When connected to
these devices, if required, the software can disable the park mode if you
see performance drop in your system. When park mode is disabled,
pipelining of multiple packet is disabled and instead one packet at a time
is requested by the scheduler. This allows up to 12 NAKs in a micro-frame
and improves performance of these slow devices.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20230419020044.15475-1-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the probe variable declarations by removing the stray newlines.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-12-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe callback has become unwieldy so break out the clock lookups
into a new helper function to improve readability.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-11-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the PHY handling using four new helpers to initialise,
deinitialise, power on and power off all the PHYs.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-10-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the core init error handling by using descriptive names for the
error labels and releasing resourcing in reverse order consistently.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-9-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While there likely are no platforms out there that mix generic and
legacy PHYs the driver should still be able to handle that, if only for
consistency reasons.
Add the missing calls to shutdown any legacy PHYs if generic PHY
initialisation fails.
Note that we continue to happily ignore potential errors from the legacy
PHY callbacks...
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-8-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hibernation code is broken and has never been enabled in mainline
and should thus be dropped.
Specifically, the scratch buffer DMA mapping would have been leaked on
every suspend cycle since commit 51f5d49ad6f0 ("usb: dwc3: core:
simplify suspend/resume operations") if this feature was ever enabled.
The related error handling was also broken and could have resulted in
attempts to unmap never mapped buffers, etc.
This effectively revert commit 0ffcaf3798bf ("usb: dwc3: core: allocate
scratch buffers").
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hibernation code is broken and has never been enabled in mainline
and should thus be dropped.
Remove the hibernation bits from the gadget code, which effectively
reverts commits e1dadd3b0f27 ("usb: dwc3: workaround: bogus hibernation
events") and 7b2a0368bbc9 ("usb: dwc3: gadget: set KEEP_CONNECT in case
of hibernation") except for the spurious interrupt warning.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing calls to disable autosuspend on probe errors and on
driver unbind.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to balance the runtime PM usage count on driver unbind by
adding back the pm_runtime_allow() call that had been erroneously
removed.
Fixes: 266d0493900a ("usb: dwc3: core: don't trigger runtime pm when remove driver")
Cc: stable@vger.kernel.org # 5.9
Cc: Li Jun <jun.li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure not to suspend the device when probe fails to avoid disabling
clocks and phys multiple times.
Fixes: 328082376aea ("usb: dwc3: fix runtime PM in error path")
Cc: stable@vger.kernel.org # 4.8
Cc: Roger Quadros <rogerq@ti.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several USB drivers use of_platform_* functions which are declared in
of_platform.h. of_platform.h gets implicitly included by of_device.h,
but that is going to be removed soon. Nothing else depends on of_device.h
so it can be dropped.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230410232639.1561152-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here for testing, and this resolves two merge
conflicts, one pointed out by linux-next:
drivers/usb/dwc3/dwc3-pci.c
drivers/usb/host/xhci-pci.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB host sends function suspend and function resume notifications to
the interface through SET_FEATURE/CLEAR_FEATURE setup packets.
Add support to handle these packets by delegating the requests to
composite layer. Also add support to handle function wake notification
requests to exit from function suspend state.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Link: https://lore.kernel.org/r/1679694482-16430-5-git-send-email-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An usb device can initate a remote wakeup and bring the link out of
suspend as dictated by the DEVICE_REMOTE_WAKEUP feature selector.
Add support to handle this packet and set the remote wakeup capability.
Some hosts may take longer time to initiate the resume signaling after
device triggers a remote wakeup. So add async support to the wakeup API
by enabling link status change events.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Link: https://lore.kernel.org/r/1679694482-16430-3-git-send-email-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Explicitly set and clear wakeup config so we don't leave anything
to chance.
Clear wakeup status on suspend so we know what caused wake up.
The LINESTATE wake up should not be enabled in device mode
if we are not connected to a USB host and in USB suspend (U2/L3)
else it will cause spurious wake up.
For now, don't enable LINESTATE. This means wake up from
USB resume will not work but at least we won't have any spurious
wake ups.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230324114429.21838-1-rogerq@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the description of platform_get_irq()
* Return: non-zero IRQ number on success,
negative error number on failure.
and the code, platform_get_irq() will return -EINVAL
instead of IRQ0.
So platform_get_irq() no longer returns 0, there is no
need to check whether the return value is 0.
Found by Smatch:
drivers/usb/dwc3/host.c:60 dwc3_host_get_irq()
warn: platform_get_irq() does not return zero
Signed-off-by: Mingxuan Xiang <mx_xiang@hust.edu.cn>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230324060934.1686859-1-mx_xiang@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes here, and the USB gadget update for future
development patches to be based on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 5 missing register dump for debugfs as they are in use now.
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1679043328-13425-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB module can wakeup system. Enable it as a wakeup source
by default. Finer grain wakeup enable/disable can be done
from the power/wakeup system control file of the respective
USB device.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230316131226.89540-3-rogerq@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB2SS IP in TI's AM62 SoC is capable of supporting wakeup from
deep sleep based on the following events,
1) VBUS state change
2) Overcurrent detection
3) Line state change
Wakeup from these events can enabled by setting their corresponding bits
in the WAKEUP_CONFIG register. The events to be enabled are decided based
on the current role of the controller.
When the role of the controller is host, the comparators for detecting
VBUS state change are disabled while entering low power mode. This is done
as VBUS state is not used in host mode and disabling the comparators helps
in reducing the power consumption. So, wakeup from VBUS state change should
be disabled in host mode. While operating in peripheral mode all the wakeup
events can be enabled.
Therefore, add support for the same in the suspend/resume hooks.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230316131226.89540-2-rogerq@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() only return non-zero irq number on success, or
negative error number on failure.
There is no need to check the return value of platform_get_irq()
to determine the return value of dwc3_gadget_get_irq(), removing
them to solve this problem.
Signed-off-by: Yalong Zou <yalongz@hust.edu.cn>
Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230309150815.1884260-1-yalongz@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
some __dynamic_array() buffer will only used at trace event output time,
change to __get_buf() which will allocate tempary trace seq buffer for
output purpose.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1677465850-1396-4-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we process the suspend interrupt event only if the
device is in configured state. Consider a case where device
is not configured and got suspend interrupt, in that case our
gadget will still use 100mA as composite_suspend didn't happen.
But battery charging specification (BC1.2) expects a downstream
device to draw less than 2.5mA when unconnected OR suspended.
Fix this by removing the condition for processing suspend event,
and thus composite_resume would set vbus draw to 2.
Fixes: 72704f876f50 ("dwc3: gadget: Implement the suspend entry event handler")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1677217619-10261-2-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some ULPI USB PHY does not support internal VBUS supply, to drive the CPEN
pin, which requires the configuration of the ULPI DRVVBUSEXTERNAL bit of
OTG_CTRL register.
Added 'snps,ulpi-ext-vbus-drv' a DT property to configure the USB2 PHY to
drive VBUS with an external supply, by setting the USB2 PHY ULPIEXTVBUSDRV
bit[:17] of the GUSB2PHYCFG register to drive VBUS with an external supply.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20230215093146.5812-3-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, there was a 100uS delay inserted after issuing an end transfer
command for specific controller revisions. This was due to the fact that
there was a GUCTL2 bit field which enabled synchronous completion of the
end transfer command once the CMDACT bit was cleared in the DEPCMD
register. Since this bit does not exist for all controller revisions and
the current implementation heavily relies on utizling the EndTransfer
command completion interrupt, add the delay back in for uses where the
interrupt on completion bit is not set, and increase the duration to 1ms
for the controller to complete the command.
An issue was seen where the USB request buffer was unmapped while the DWC3
controller was still accessing the TRB. However, it was confirmed that the
end transfer command was successfully submitted. (no end transfer timeout)
In situations, such as dwc3_gadget_soft_disconnect() and
__dwc3_gadget_ep_disable(), the dwc3_remove_request() is utilized, which
will issue the end transfer command, and follow up with
dwc3_gadget_giveback(). At least for the USB ep disable path, it is
required for any pending and started requests to be completed and returned
to the function driver in the same context of the disable call. Without
the GUCTL2 bit, it is not ensured that the end transfer is completed before
the buffers are unmapped.
Fixes: cf2f8b63f7f1 ("usb: dwc3: gadget: Remove END_TRANSFER delay")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230306200557.29387-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_gpio.h provides a single function, which is not used in this driver.
Remove unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230215165239.83806-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Note, the root dentry for the debugfs directory for the device needs to
be saved so we don't have to keep looking it up, which required a bit
more refactoring to properly create and remove it when needed.
Reported-by: Bruce Chen <bruce.chen@unisoc.com>
Reported-by: Cixi Geng <cixi.geng1@unisoc.com>
Tested-by: Cixi Geng <gengcixi@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230202152820.2409908-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With vbus override enabled when in OTG dr_mode, Host<->Peripheral
switch now works on SM8550, otherwise the DWC3 seems to be stuck
in Host mode only.
Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230123-topic-sm8550-upstream-dwc3-qcom-otg-v2-1-2d400e598463@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3 core support now links against the extcon subsystem,
so it cannot be built-in when extcon is a loadable module:
arm-linux-gnueabi-ld: drivers/usb/dwc3/core.o: in function `dwc3_get_extcon':
core.c:(.text+0x572): undefined reference to `extcon_get_edev_by_phandle'
arm-linux-gnueabi-ld: core.c:(.text+0x596): undefined reference to `extcon_get_extcon_dev'
arm-linux-gnueabi-ld: core.c:(.text+0x5ea): undefined reference to `extcon_find_edev_by_node'
There was already a Kconfig dependency in the dual-role support,
but this is now needed for the entire dwc3 driver.
It is still possible to build dwc3 without extcon, but this
prevents it from being set to built-in when extcon is a loadable
module.
Fixes: d182c2e1bc92 ("usb: dwc3: Don't switch OTG -> peripheral if extcon is present")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230118090147.2126563-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we delay sending End Transfer for Setup TRB to be prepared, we need
to check if the End Transfer was in preparation for a driver
teardown/soft-disconnect. In those cases, just send the End Transfer
command without delay.
In the case of soft-disconnect, there's a very small chance the command
may not go through immediately. But should it happen, the Setup TRB will
be prepared during the polling of the controller halted state, allowing
the command to go through then.
In the case of disabling endpoint due to reconfiguration (e.g.
set_interface(alt-setting) or usb reset), then it's driven by the host.
Typically the host wouldn't immediately cancel the control request and
send another control transfer to trigger the End Transfer command
timeout.
Fixes: 4db0fbb60136 ("usb: dwc3: gadget: Don't delay End Transfer on delayed_status")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f1617a323e190b9cc408fb8b65456e32b5814113.1670546756.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added gpio consumer calls cause a build failure in configurations
that fail to include the right header implicitly:
drivers/usb/dwc3/dwc3-xilinx.c: In function 'dwc3_xlnx_init_zynqmp':
drivers/usb/dwc3/dwc3-xilinx.c:207:22: error: implicit declaration of function 'devm_gpiod_get_optional'; did you mean 'devm_clk_get_optional'? [-Werror=implicit-function-declaration]
207 | reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
| ^~~~~~~~~~~~~~~~~~~~~~~
| devm_clk_get_optional
Fixes: ca05b38252d7 ("usb: dwc3: xilinx: Add gpio-reset support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230103121755.956027-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 0f0101719138 ("usb: dwc3: Don't switch OTG -> peripheral
if extcon is present"), Dual Role support on Intel Merrifield platform
broke due to rearranging the call to dwc3_get_extcon().
It appears to be caused by ulpi_read_id() masking the timeout on the first
test write. In the past dwc3 probe continued by calling dwc3_core_soft_reset()
followed by dwc3_get_extcon() which happend to return -EPROBE_DEFER.
On deferred probe ulpi_read_id() finally succeeded. Due to above mentioned
rearranging -EPROBE_DEFER is not returned and probe completes without phy.
On Intel Merrifield the timeout on the first test write issue is reproducible
but it is difficult to find the root cause. Using a mainline kernel and
rootfs with buildroot ulpi_read_id() succeeds. As soon as adding
ftrace / bootconfig to find out why, ulpi_read_id() fails and we can't
analyze the flow. Using another rootfs ulpi_read_id() fails even without
adding ftrace. We suspect the issue is some kind of timing / race, but
merely retrying ulpi_read_id() does not resolve the issue.
As we now changed ulpi_read_id() to return -ETIMEDOUT in this case, we
need to handle the error by calling dwc3_core_soft_reset() and request
-EPROBE_DEFER. On deferred probe ulpi_read_id() is retried and succeeds.
Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT")
Cc: stable@vger.kernel.org
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Link: https://lore.kernel.org/r/20221205201527.13525-3-ftoth@exalondelft.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_icc_get() alloc resources for path handle, we should release it when not
need anymore. Like the release in dwc3_qcom_interconnect_exit() function.
Add icc_put() in error handling to fix this.
Fixes: bea46b981515 ("usb: dwc3: qcom: Add interconnect support in dwc3 driver")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20221206081731.818107-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc->desired_dr_role is changed by dwc3_set_mode inside a spinlock but
then read by __dwc3_set_mode outside of that lock. This can lead to a
race condition when very quick successive role switch events happen:
CPU A
dwc3_set_mode(DWC3_GCTL_PRTCAP_HOST) // first role switch event
spin_lock_irqsave(&dwc->lock, flags);
dwc->desired_dr_role = mode; // DWC3_GCTL_PRTCAP_HOST
spin_unlock_irqrestore(&dwc->lock, flags);
queue_work(system_freezable_wq, &dwc->drd_work);
CPU B
__dwc3_set_mode
// ....
spin_lock_irqsave(&dwc->lock, flags);
// desired_dr_role is DWC3_GCTL_PRTCAP_HOST
dwc3_set_prtcap(dwc, dwc->desired_dr_role);
spin_unlock_irqrestore(&dwc->lock, flags);
CPU A
dwc3_set_mode(DWC3_GCTL_PRTCAP_DEVICE) // second event
spin_lock_irqsave(&dwc->lock, flags);
dwc->desired_dr_role = mode; // DWC3_GCTL_PRTCAP_DEVICE
spin_unlock_irqrestore(&dwc->lock, flags);
CPU B (continues running __dwc3_set_mode)
switch (dwc->desired_dr_role) { // DWC3_GCTL_PRTCAP_DEVICE
// ....
case DWC3_GCTL_PRTCAP_DEVICE:
// ....
ret = dwc3_gadget_init(dwc);
We then have DWC3_GCTL.DWC3_GCTL_PRTCAPDIR = DWC3_GCTL_PRTCAP_HOST and
dwc->current_dr_role = DWC3_GCTL_PRTCAP_HOST but initialized the
controller in device mode. It's also possible to get into a state
where both host and device are intialized at the same time.
Fix this race by creating a local copy of desired_dr_role inside
__dwc3_set_mode while holding dwc->lock.
Fixes: 41ce1456e1db ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20221128161526.79730-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device ID 0xa70e is defined for the USB3 device controller in the CPU
sub-system of Raptor Lake platform. Hence updating the ID accordingly.
Fixes: bad0d1d726ac ("usb: dwc3: pci: Add support for Intel Raptor Lake")
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Shruthi Sanil <shruthi.sanil@intel.com>
Link: https://lore.kernel.org/r/20221125105327.27945-1-shruthi.sanil@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A request to Manish Narani (see Link) asked for clarification of the
reference to the config ARCH_VERSAL in the support of Xilinx SoCs with
DesignWare Core USB3 IP.
As there is no response, clean up the reference to the non-existing config
symbol. While at it, follow up on Felipe Balbi's request to add the
alternative COMPILE_TEST dependency.
Link: https://lore.kernel.org/all/CAKXUXMwgWfX8+OvY0aCwRNukencwJERAZzU7p4eOLXQ2zv6rAg@mail.gmail.com/
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20221116110444.8340-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until the endpoint is disabled, its descriptors should remain valid.
When its requests are removed from ep disable, the request completion
routine may attempt to access the endpoint's descriptor. Don't clear the
descriptors before that.
Fixes: f09ddcfcb8c5 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/45db7c83b209259115bf652af210f8b2b3b1a383.1668561364.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
