IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring fields.
Use memset_startat() so memset() doesn't get confused about writing
beyond the destination member that is intended to be the starting point
of zeroing through the end of the struct. Additionally split up a later
field-spanning memset() so that memset() can reason about the size.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118202416.1286046-1-keescook@chromium.org
This reverts commit 46e46db313a2bf3c48cac4eb8bdb613b762f301b. Mark reported
that it breaks QCA6390 hw2.0 on Dell XPS 13 9310:
[ 5.537034] ath11k_pci 0000:72:00.0: chip_id 0x0 chip_family 0xb board_id 0xff soc_id 0xffffffff
[ 5.537038] ath11k_pci 0000:72:00.0: fw_version 0x101c06cc fw_build_timestamp 2020-06-24 19:50 fw_build_id
[ 5.537236] ath11k_pci 0000:72:00.0: failed to fetch board data for bus=pci,qmi-chip-id=0,qmi-board-id=255,variant=DE_1901 from ath11k/QCA6390/hw2.0/board-2.bin
[ 5.537255] ath11k_pci 0000:72:00.0: failed to fetch board-2.bin or board.bin from QCA6390/hw2.0
[ 5.537257] ath11k_pci 0000:72:00.0: qmi failed to fetch board file: -2
[ 5.537258] ath11k_pci 0000:72:00.0: failed to load board data file: -2
So we need to back to the drawing board and implement it so that backwards
compatiblity is not broken.
Reported-by: Mark Herbert <mark.herbert42@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211124094316.9096-1-kvalo@codeaurora.org
In HE monitor capture, HAL_TLV_STATUS_PPDU_DONE is received
on processing multiple skb. Do not clear the ppdu_info
till the HAL_TLV_STATUS_PPDU_DONE is received.
This fixes below warning and packet drops in monitor mode.
"Rate marked as an HE rate but data is invalid: MCS: 6, NSS: 0"
WARNING: at
PC is at ieee80211_rx_napi+0x624/0x840 [mac80211]
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01693-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637249433-10316-1-git-send-email-akolli@codeaurora.org
This is to read variant from SMBIOS such as read from DT, the variant
string will be used to one part of string which used to search board
data from board-2.bin.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118100033.8384-1-quic_wgong@quicinc.com
The ath11k driver currently sends vdev down to the firmware before
updating the channel context, which is followed by a vdev restart
command.
Sending vdev down is not required before sending a vdev restart,
because the firmware internally does vdev down when ath11k sends
a vdev restart command.
Firmware will happen crash while channel switch without this change.
Hence skip the vdev down command sending when updating the channel
context and then fix the firmware crash issue.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095901.8271-1-quic_wgong@quicinc.com
The pdev id is set to 0 for single pdev configured hardware, the real
pdev id is not 0 in firmware, for example, its pdev id is 1 for 5G/6G
phy and 2 for 2G band phy. For HTT_H2T_MSG_TYPE_EXT_STATS_CFG message,
firmware parse the pdev_mask to its pdev id, ath11k set it to 0 for
single pdev, it is not correct, need set it with the real pdev id of
firmware.
Save the real pdev id report by firmware and set it correctly.
Below commands run success with this patch:
cat /sys/kernel/debug/ieee80211/phy0/ath11k/htt_stats
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wls1/stations/00\:03\:7f\:75\:59\:85/htt_peer_stats
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095700.8149-1-quic_wgong@quicinc.com
When connected to 6G mode AP, it does not have VHT/HT capabilities,
so the NSS is not set, then it is 1 by default.
This patch is to calculate the NSS with supported HE-MCS and NSS set
of HE capabilities.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01280-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095453.8030-1-quic_wgong@quicinc.com
Some firmware versions for WCN6855 report the default regdomain with
alpha code "na" by default when load as a world wide regdomain, ath11k
should treat it as a world wide alpha code.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118094848.7776-1-quic_wgong@quicinc.com
With VT-d disabled on Intel platform, ath11k gets only one MSI
vector. In that case, ath11k does not free IRQ when doing suspend,
hence the kernel has to migrate it to CPU0 (if it was affine to
other CPUs) and allocates a new MSI vector. However, ath11k has
no chance to reconfig it to HW srngs during this phase, thus
ath11k fails to resume.
This issue can be fixed by setting IRQ affinity to CPU0 before
request_irq is called. With such affinity, migration will not
happen and thus the vector keeps unchanged during suspend/resume.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041732.5323-1-bqiang@codeaurora.org
Current code enables ASPM by default, it allows MHI to enter M2 state.
In case of one MSI vector, system hang is observed if ath11k does MHI
register reading in this state. The issue was reported on Dell XPS 13
9310 but is seen also on XPS 15 and XPS 17 laptops.
The workaround here is to prevent MHI from entering M2 state, this can
be done by disabling ASPM if only one MSI vector is used. When using 32
vectors ASPM is enabled as before.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041722.5271-1-bqiang@codeaurora.org
On some platforms it's not possible to allocate 32 MSI vectors for various
reasons, be it kernel configuration, VT-d disabled, buggy BIOS etc. So
ath11k was not able to use QCA6390 PCI devices on those platforms. Add
support for one MSI vector to solve that.
In case of one MSI vector, interrupt migration needs to be disabled. This
is because when interrupt migration happens, the msi_data may change.
However, msi_data is already programmed to rings during initial phase and
ath11k has no way to know that msi_data is changed during run time and
reprogram again.
In case of one MSI vector, MHI subsystem should not use IRQF_NO_SUSPEND
as QCA6390 doesn't set this flag too. Ath11k doesn't need to leave
IRQ enabled in suspend state.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041714.5219-1-bqiang@codeaurora.org
This is to prepare for one MSI vector support. IRQ enable and disable
of CE and DP are done only in case of multiple MSI vectors.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041705.5167-1-bqiang@codeaurora.org
Like ATH11K_PCI_IRQ_CE0_OFFSET, define ATH11K_PCI_IRQ_DP_OFFSET for
DP to save the IRQ instead of base_vector from MSI config.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041655.5112-1-bqiang@codeaurora.org
This change adds two flags to indicate whether IRQ handler for CE
and DP can be called. This is because in one MSI vector case,
interrupt is not disabled in hif_stop and hif_irq_disable. Otherwise,
MHI interrupt is disabled too.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041646.5060-1-bqiang@codeaurora.org
The reservation mode of interrupts in kernel assigns a dummy vector
when the interrupt is allocated and assigns a real vector when the
request_irq is called. The reservation mode helps to ease vector
pressure when devices with a large amount of queues/interrupts
are initialized, but only a minimal subset of those queues/interrupts
is actually used.
So on reservation mode, the msi_data may change after request_irq
is called, so ath11k reads msi_data again after request_irq is called,
and then the correct msi_data is programmed into QCA6390 hardware
components. Without this change, spurious interrupt occurs in case of
one MSI vector. When VT-d in BIOS is enabled and ath11k can get 32 MSI
vectors, ath11k always get the same msi_data before and after request_irq,
that's why this change is only required when one MSI vector is to be
supported.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041636.5008-1-bqiang@codeaurora.org
ath.git patches for v5.17. Major changes:
ath10k
* fetch (pre-)calibration data via nvmem subsystem
ath11k
* enable 802.11 power save mode in station mode for qca6390 and wcn6855
* trace log support
* proper board file detection for WCN6855 based on PCI ids
* BSS color change support
The struct ath_hw member intr_txqs is never reset/assigned outside
of ath9k_hw_init_queues() and with the used bitwise-or in the interrupt
handling ar9002_hw_get_isr() accumulates all ever set interrupt flags.
Fix this by using a pure assign instead of bitwise-or for the
first line (note: intr_txqs is only evaluated in case ATH9K_INT_TX bit
is set).
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211116220720.30145-1-ps.report@gmx.net
Wakeup mhi is needed before pci_read/write only for QCA6390 and WCN6855. Since
wakeup & release mhi is enabled for all hardwares, below mhi assert is seen in
QCN9074 when doing 'rmmod ath11k_pci':
Kernel panic - not syncing: dev_wake != 0
CPU: 2 PID: 13535 Comm: procd Not tainted 4.4.60 #1
Hardware name: Generic DT based system
[<80316dac>] (unwind_backtrace) from [<80313700>] (show_stack+0x10/0x14)
[<80313700>] (show_stack) from [<805135dc>] (dump_stack+0x7c/0x9c)
[<805135dc>] (dump_stack) from [<8032136c>] (panic+0x84/0x1f8)
[<8032136c>] (panic) from [<80549b24>] (mhi_pm_disable_transition+0x3b8/0x5b8)
[<80549b24>] (mhi_pm_disable_transition) from [<80549ddc>] (mhi_power_down+0xb8/0x100)
[<80549ddc>] (mhi_power_down) from [<7f5242b0>] (ath11k_mhi_op_status_cb+0x284/0x3ac [ath11k_pci])
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[<7f5242b0>] (ath11k_mhi_op_status_cb [ath11k_pci]) from [<7f524878>] (ath11k_mhi_stop+0x10/0x20 [ath11k_pci])
[<7f524878>] (ath11k_mhi_stop [ath11k_pci]) from [<7f525b94>] (ath11k_pci_power_down+0x54/0x90 [ath11k_pci])
[<7f525b94>] (ath11k_pci_power_down [ath11k_pci]) from [<8056b2a8>] (pci_device_shutdown+0x30/0x44)
[<8056b2a8>] (pci_device_shutdown) from [<805cfa0c>] (device_shutdown+0x124/0x174)
[<805cfa0c>] (device_shutdown) from [<8033aaa4>] (kernel_restart+0xc/0x50)
[<8033aaa4>] (kernel_restart) from [<8033ada8>] (SyS_reboot+0x178/0x1ec)
[<8033ada8>] (SyS_reboot) from [<80301b80>] (ret_fast_syscall+0x0/0x34)
Hence, disable wakeup/release mhi using hw_param for other hardwares.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01060-QCAHKSWPL_SILICONZ-1
Fixes: a05bd8513335 ("ath11k: read and write registers below unwindowed address")
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636702019-26142-1-git-send-email-quic_seevalam@quicinc.com
In following patches, dev_watchdog() will no longer stop all queues.
It will read queue->trans_start locklessly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ath11k driver is caching the information about RSN/WPA IE in the
configured beacon template. The cached information is used during
associations to figure out whether 4-way PKT/2-way GTK peer flags need to
be set or not.
But the code never cleared the state when no such IE was found. This can
for example happen when moving from an WPA/RSN to an open setup. The
(seemingly connected) peer was then not able to communicate over the
link because the firmware assumed a different (encryption enabled) state
for the peer.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: 01e34233c645 ("ath11k: fix wmi peer flags in peer assoc command")
Cc: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-2-sven@narfation.org
DISABLE_KEY sets the key_len to 0, firmware will not delete the keys if
key_len is 0. Changing from security mode to open mode will cause mcast
to be still encrypted without vdev restart.
Set the proper key_len for DISABLE_KEY cmd to clear the keys in
firmware.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-1-sven@narfation.org
Whenever the MAC detects a color collision, or any of
its associated stations detects one, the firmware will
send out an event. Add the code to parse and handle
this event and pass the data up to mac80211.
The firmware does not provide an offload feature such
as the one used for CSA. The color change process is
hence triggered via the beacon offload tx completion
events sent out by firmware.
BSS color feature is enabled depending on service flag
advertised by firmware, based on which color change
functionality is invoked.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00680-QCAHKSWPL_SILICONZ-1
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635178254-17732-1-git-send-email-quic_ramess@quicinc.com
Currently ath11k only support string type with bus, chip id and board id
such as "bus=ahb,qmi-chip-id=1,qmi-board-id=4" for ahb bus chip and
"bus=pci,qmi-chip-id=0,qmi-board-id=255" for PCIe bus chip in
board-2.bin. For WCN6855, it is not enough to distinguish all different
chips.
This is to add a new string type which include bus, chip id, board id,
vendor, device, subsystem-vendor and subsystem-device for WCN6855.
ath11k will first load board-2.bin and search in it for the board data
with the above parameters, if matched one board data, then download it
to firmware, if not matched any one, then ath11k will download the file
board.bin to firmware.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211111065340.20187-1-quic_wgong@quicinc.com
Currently many functions do not follow this guidance when
qmi_send_request() fails, therefore add missing
qmi_txn_cancel() in the qmi_send_request() error path.
Also remove initialization on 'struct qmi_txn'
since qmi_tx_init() performs all necessary initialization.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635857558-21733-1-git-send-email-akolli@codeaurora.org
The DMA buffers of dbring which is used for spectral/cfr
starts at certain offset from original kmalloc() returned buffer.
This is not cache line aligned.
And also driver tries to access the data that is immediately before
this offset address (i.e. buff->paddr) after doing dma map.
This will cause cache line sharing issues and data corruption,
if CPU happen to write back cache after HW has dma'ed the data.
Fix this by mapping a cache line aligned buffer to dma.
Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635831693-15962-1-git-send-email-quic_ramess@quicinc.com
Firmware credit flow control is enabled for WMI control services,
which expects available tokens should be acquired before sending a
command to the target. Also the token gets released when firmware
receives the command.
This credit-based flow limits driver to send WMI command only
when the token available which is causing WMI commands to timeout and
return -EAGAIN, whereas firmware has enough capability to process the
WMI command. To fix this Tx starvation issue, introduce the ability to
disable the credit flow for the WMI path.
The driver sends WMI configuration for disabling credit flow to firmware
by two ways.
1. By using a global flag
(HTC_MSG_SETUP_COMPLETE_EX_ID msg type flags)
2. By using a local flag
(ATH11K_HTC_CONN_FLAGS_DISABLE_CREDIT_FLOW_CTRL = 1 << 3)
Ath11k uses both these configurations to disable credit flow for the
WMI path completely.
Also added a hw_param member for credit flow control by which we can
enable or disable it based on per-target basis. Currently we are disabling
credit flow for IPQ8074, IPQ6018, and QCN9074 as recommended by firmware.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Co-developed-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635156494-20059-1-git-send-email-quic_ppranees@quicinc.com
Some ETSI countries have a small overlap in the wireless-regdb with an ETSI
channel (5590-5650). A good example is Australia:
country AU: DFS-ETSI
(2400 - 2483.5 @ 40), (36)
(5150 - 5250 @ 80), (23), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (20), NO-OUTDOOR, AUTO-BW, DFS
(5470 - 5600 @ 80), (27), DFS
(5650 - 5730 @ 80), (27), DFS
(5730 - 5850 @ 80), (36)
(57000 - 66000 @ 2160), (43), NO-OUTDOOR
If the firmware (or the BDF) is shipped with these rules then there is only
a 10 MHz overlap with the weather radar:
* below: 5470 - 5590
* weather radar: 5590 - 5600
* above: (none for the rule "5470 - 5600 @ 80")
There are several wrong assumption in the ath11k code:
* there is always a valid range below the weather radar
(actually: there could be no range below the weather radar range OR range
could be smaller than 20 MHz)
* intersected range in the weather radar range is valid
(actually: the range could be smaller than 20 MHz)
* range above weather radar is either empty or valid
(actually: the range could be smaller than 20 MHz)
These wrong assumption will lead in this example to a rule
(5590 - 5600 @ 20), (N/A, 27), (600000 ms), DFS, AUTO-BW
which is invalid according to is_valid_reg_rule() because the freq_diff is
only 10 MHz but the max_bandwidth is set to 20 MHz. Which results in a
rejection like:
WARNING: at backports-20210222_001-4.4.60-b157d2276/net/wireless/reg.c:3984
[...]
Call trace:
[<ffffffbffc3d2e50>] reg_get_max_bandwidth+0x300/0x3a8 [cfg80211]
[<ffffffbffc3d3d0c>] regulatory_set_wiphy_regd_sync+0x3c/0x98 [cfg80211]
[<ffffffbffc651598>] ath11k_regd_update+0x1a8/0x210 [ath11k]
[<ffffffbffc652108>] ath11k_regd_update_work+0x18/0x20 [ath11k]
[<ffffffc0000a93e0>] process_one_work+0x1f8/0x340
[<ffffffc0000a9784>] worker_thread+0x25c/0x448
[<ffffffc0000aedc8>] kthread+0xd0/0xd8
[<ffffffc000085550>] ret_from_fork+0x10/0x40
ath11k c000000.wifi: failed to perform regd update : -22
Invalid regulatory domain detected
To avoid this, the algorithm has to be changed slightly. Instead of
splitting a rule which overlaps with the weather radar range into 3 pieces
and accepting the first two parts blindly, it must actually be checked for
each piece whether it is a valid range. And only if it is valid, add it to
the output array.
When these checks are in place, the processed rules for AU would end up as
country AU: DFS-ETSI
(2400 - 2483 @ 40), (N/A, 36), (N/A)
(5150 - 5250 @ 80), (6, 23), (N/A), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (6, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW
(5470 - 5590 @ 80), (6, 27), (0 ms), DFS, AUTO-BW
(5650 - 5730 @ 80), (6, 27), (0 ms), DFS, AUTO-BW
(5730 - 5850 @ 80), (6, 36), (N/A), AUTO-BW
and will be accepted by the wireless regulatory code.
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112153116.1214421-1-sven@narfation.org
There is a race condition whereby the tx completion handler can be invoked
before the 'num_pending_mgmt_tx" count is incremented. If that occurs, we
could get warning trace indicating that 'num_pending_mgmt_tx' is 0 (because
it was not yet incremented). Ideally, this trace should be seen only if
mgmt tx has not happened but tx completion is received, and it is not
expected in this race condition.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635168282-8845-1-git-send-email-quic_ppranees@quicinc.com
Set proper values for max_regpower, max_power, max_antenna_gain as it
is because firmware will convert power values to 0.5dbm steps by
multiplying it with 2.
If txpower is not set, it will lead to cca stuck resulting in latency
issues for QCN9074.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635164229-22880-1-git-send-email-quic_ppranees@quicinc.com
In radio tap header, BAD FCS flag is not updated properly because
driver failed to update FCS_ERR flag in monitor mode.
In rx_desc, FCS_ERR information is available in rx_attention
structure and presence of this field indicates corresponding frame
failed FCS check.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635164060-18423-1-git-send-email-quic_ppranees@quicinc.com
When station connect to AP, the wmi command sequence is:
peer_create->vdev_start->vdev_up
and sequence of station disconnect fo AP is:
peer_delete->vdev_down->vdev_stop
The sequence of disconnect is not opposite of connect, it caused firmware
crash when it handle wmi vdev stop cmd when the AP is support TWT of
802.11 ax, because firmware need access the bss peer for vdev stop cmd.
[ 390.438564] ath11k_pci 0000:05:00.0: wmi cmd send 0x6001 ret 0
[ 390.438567] ath11k_pci 0000:05:00.0: WMI peer create vdev_id 0 peer_addr c4:04:15:3b:e0:39
[ 390.472724] ath11k_pci 0000:05:00.0: mac vdev 0 start center_freq 2437 phymode 11ax-he20-2g
[ 390.472731] ath11k_pci 0000:05:00.0: wmi cmd send 0x5003 ret 0
[ 390.560849] ath11k_pci 0000:05:00.0: wmi cmd send 0x5005 ret 0
[ 390.560850] ath11k_pci 0000:05:00.0: WMI mgmt vdev up id 0x0 assoc id 1 bssid c4:04:15:3b:e0:39
[ 399.432896] ath11k_pci 0000:05:00.0: WMI peer delete vdev_id 0 peer_addr c4:04:15:3b:e0:39
[ 399.432902] ath11k_pci 0000:05:00.0: wmi cmd send 0x6002 ret 0
[ 399.441380] ath11k_pci 0000:05:00.0: wmi cmd send 0x5007 ret 0
[ 399.441381] ath11k_pci 0000:05:00.0: WMI vdev down id 0x0
[ 399.454681] ath11k_pci 0000:05:00.0: wmi cmd send 0x5006 ret 0
[ 399.454682] ath11k_pci 0000:05:00.0: WMI vdev stop id 0x0
The opposite sequence of disconnect should be:
vdev_down->vdev_stop->peer_delete
This patch change the sequence of disconnect for station as above
opposite sequence for QCA6390, firmware not crash again with this patch.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027093825.12167-1-quic_wgong@quicinc.com
parameter of msecs_to_jiffies should be (3 * 1000) instead of (3 * HZ)
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026032014.27010-1-quic_wgong@quicinc.com
Currently in ath11k_mac_op_sta_statistics() there is the following
logic:
if (!arsta->txrate.legacy && !arsta->txrate.nss)
return;
Unfortunately if this condition is true then the function returns without
setting parameters that follow the txrate. To address this issue remove the
return and instead invert the logic to set the txrate logic if
(arsta->txrate.legacy || arsta->txrate.nss).
The same was done also in ath10k in commit 1cd6ba8ae33e ("ath10k: remove return
for NL80211_STA_INFO_TX_BITRATE").
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011084957.31024-1-wgong@codeaurora.org
When NSS ratio enabled reported by firmware, SUPPORTS_VHT_EXT_NSS_BW
is set in ath11k, meanwhile IEEE80211_VHT_EXT_NSS_BW_CAPABLE also
need to be set, otherwise it is invalid because spec in IEEE Std
802.11™‐2020 as below.
Table 9-273-Supported VHT-MCS and NSS Set subfields, it has subfield
VHT Extended NSS BW Capable, its definition is:
Indicates whether the STA is capable of interpreting the Extended NSS
BW Support subfield of the VHT Capabilities Information field.
dmesg have a message without this patch:
ieee80211 phy0: copying sband (band 1) due to VHT EXT NSS BW flag
It means mac80211 will set IEEE80211_VHT_EXT_NSS_BW_CAPABLE if ath11k not
set it in ieee80211_register_hw(). So it is better to set it in ath11k.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211013073704.15888-1-wgong@codeaurora.org
Avoid unnecessary idr_find calls before the idr_remove calls. Because
idr_remove gives the valid ptr if id is valid otherwise return NULL ptr.
So removed the idr_find before idr_remove in tx completion path. Also no
need to disable the bottom half preempt if it is already in the
bottom half context, so modify the spin_lock_bh to spin_lock in the
data tx completion path.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-13-git-send-email-ppranees@codeaurora.org
Add branch prediction in dp_tx code path in tx and tx completion handlers.
Also in ath11k_dp_tx_complete_msdu , the pointer that is returned by
rcu_dereference() is not dereferenced. so it is preferable to use
rcu_access_pointer() here.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-12-git-send-email-ppranees@codeaurora.org
Currently while loop is used to find the tx completion ring number and
it is not required since the tx ring mask and the group id can be combined
to directly fetch the ring number. Hence remove the while loop
and directly get the ring number from tx mask and group id.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-11-git-send-email-ppranees@codeaurora.org
Replace use of mod operator with a manual wrap around
to avoid additional cost of using mod operation.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-10-git-send-email-ppranees@codeaurora.org
Similar to REO destination ring, also allocate HAL_WBM2SW_RELEASE
from cacheable memory so that descriptors could be prefetched during
tx completion handling.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-9-git-send-email-ppranees@codeaurora.org
In datapath, add branch predictors where required in the process rx().
This protects high value rx path without having performance overhead.
Also while processing rx packets, the pointer that is returned by
rcu_dereference() is not dereferenced. so it is preferable to use
rcu_access_pointer() here.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-8-git-send-email-ppranees@codeaurora.org
The usage of quota variable inside ath11k_dp_rx_process_received_packets()
is redundant. Since we would queue only max packets to the list before
calling this function so it would never exceed quota. Hence removing
usage of quota variable.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-7-git-send-email-ppranees@codeaurora.org
The Active Pdev and CAC check are done for each msdu in
ath11k_dp_rx_process_received_packets which is a overhead.
To avoid this overhead, collect all msdus in a per mac msdu
list and pass to function.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-6-git-send-email-ppranees@codeaurora.org
In ath11k_dp_process_rx(), after processing rx_desc from
ath11k_hal_srng_dst_get_next_entry(), ath11k_hal_srng_dst_num_free()
is accessed everytime because of done flag is not set.
To avoid this additional access to ath11k_hal_srng_dst_num_free(),
increment total_msdu_reaped only when continuation is not set and
update done flag correspondingly.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-5-git-send-email-ppranees@codeaurora.org
In data path, to reduce the CPU cycles spending on descriptor access
wrapper function, changed those functions as static inline.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-4-git-send-email-ppranees@codeaurora.org
tcl_data and reo_dst rings are currently being allocated using
dma_allocate_coherent() which is non cacheable.
Allocating ring memory from cacheable memory area allows cached descriptor
access and prefetch next descriptors to optimize CPU usage during
descriptor processing on NAPI. Based on the hardware param we can enable
or disable this feature for the corresponding platform.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-3-git-send-email-ppranees@codeaurora.org
Host driver doesn't need to process CE8 interrupts (used
by target independently)
The volume of interrupts is huge within short interval,
CPU0 CPU1 CPU2 CPU3
14022188 0 0 0 GIC 71 Edge ce8
Hence disabling unused CE8 interrupt will improve CPU usage.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-2-git-send-email-ppranees@codeaurora.org
Currently the updated bandwidth for the peer will be configured
to the firmware after channel switch from the sta_rc_update_wk.
If the updated bandwidth is greater than the configured peer phymode
during the peer assoc may result firmware assert.
For example, initially AP is in HE40 mode and the peer phymode is
configured as MODE_11AX_HE40 during peer assoc. Now user change the
channel width to HE80 then, the peer bandwidth will be updated as
HE80 to the firmware.
This will trigger firmware assert due to peer bandwidth is greater than
the peer phymode.
Fix this issue by sending peer assoc command before setting the updated
peer bandwith to firmware.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636644002-25446-1-git-send-email-quic_vnaralas@quicinc.com
