IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This patch adds missing gsbi7 uart pinctrl, this is the default debug
uart on most boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Usage of generic names like "uart_pins" is confusing to the reader, given
the fact that there could be more than one uart on APQ8064.
This patch adds gsbi prefix to uart pinctrl nodes so as to avoid such
confusion.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds support to pm8921 power button.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds rtc node for pmic8921.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch removes unnecessary eeprom label, which is not used
anywhere in the board file.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch removes unnecessary eeprom label, which is not used
anywhere in the board file.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch removes i2c pinctrl properties from board which which are now
mentioned in the SOC specific file. This will avoid redundant properties
across multiple board fiiles.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This doesn't match the binding, and the driver doesn't look to
be using it. Remove the extra element.
CC: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add low priority accumulator channel that can monitor multiple QMSS
queues. User for example could use the accumular queue for Netcp
Rx completion. While at it, also add an extra line end of each top
level node in DTS to make it more readable.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The DC5LDO regulator supplies VDD-CPUS, which is for the embedded
controller in the A31 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have axp22x.dtsi describing common axp22x hardware, use
it and reference the nodes instead of declaring the whole tree.
Also drop the "always-on" from the vdd-gpu regulator, since we don't
support the GPU anyway.
And add a regulator reference for cpu0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The power configuration on this board is the same as the pcDuino v3.
This will enable frequency/voltage scaling over the standard A20
operating points from 144 MHz to 960 MHz.
Tested using cpufreq-ljt-stress-test on two pcDuino v3 Nano boards; also
tested successfully with voltages reduced by 0.025 V.
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We've everything we need to support the gmac on Colombus, turn it on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A33 Q8 tablets with the et-q8-v1.6 pcb will work fine with the
generic q8-tablet.dts and given the many variants of PCBs found in
Q8 tablets using such a specific dts name was a mistake in hindsight.
We cannot just drop the et-q8-v1.6.dtb as existing u-boot configs
may very well point to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A23 Q8 tablets with the ippo-q8h-v* pcb will work fine with the
generic q8-tablet.dts and given the many variants of PCBs found in
Q8 tablets using such a specific dts name was a mistake in hindsight.
We cannot just drop the ippo-q8h-v*.dtb as existing u-boot configs
may very well point to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is a generic dts file for A23 based q8 formfactor tablets,
this is intended to replace both sun8i-a23-ippo-q8h-v5.dts and
sun8i-a23-ippo-q8h-v1.2.dts (these can be fully dropped after a
transition period).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached
to them and also enable USB PHY device for the Porter board. We have to
enable everything in one patch since EHCI/OHCI devices are already linked
to the USB PHY device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In DRA74x, DRA72x and AM57xx EVMs the card detect gpio is
designed as active low gpio. So correcting the dt card detect
gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM43xx the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM335x the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
uart2 pinmux is already defined in omap3-igep0020-common.dtsi, remove
the duplicate node.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use tabs instead of spaces for indentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The card detect GPIO is using IRQ_TYPE_LEVEL_LOW in the GPIO flag cells
but this defined constant is meant to be used for a IRQ and not a GPIO.
So instead use GPIO_ACTIVE_LOW that seems to be the original intention.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DRA74x family of SoCs have a second DSP, that also has
two MMUs just like the DSP1 subsystem. Add the IOMMU nodes
for this DSP2 subsystem in disabled state to the DRA74x
specific DTS file, the nodes would need to be enabled
appropriately in the respective board DTS files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DRA7xx family of SOCs have two IPUs and one DSP processor
subsystems in common. The IOMMU DT nodes have been added for
these processor subsystems, and have been disabled by default.
These MMUs are very similar to those on OMAP4 and OMAP5, with
the only difference being the presence of a second MMU within
the DSP subsystem for the EDMA port. The DSP IOMMUs also need
an additional 'ti,syscon-mmuconfig' property compared to the
IPU IOMMUs.
NOTE: The enabling of these nodes is left to the respective
board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DSP_SYSTEM sub-module is a dedicated system control logic
module present within a DRA7 DSP processor sub-system. This
module is responsible for power management, clock generation
and connection to the device PRCM module.
Add a syscon node for this module for the DSP2 processor
sub-system. This is added as a syscon node as it is a common
configuration module that can be used by the different IOMMU
instances and the corresponding remoteproc device.
The node is added to the dra74x.dtsi file, as the DSP2 processor
subsystem is usually present only on the DRA74x variants of the
DRA7 SoC family.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DSP_SYSTEM sub-module is a dedicated system control logic
module present within a DRA7 DSP processor sub-system. This
module is responsible for power management, clock generation
and connection to the device PRCM module.
Add a syscon node for this module for the DSP1 processor
sub-system. This is added as a syscon node as it is a common
configuration module that can be used by the different IOMMU
instances and the corresponding remoteproc device.
The node is added to the common dra7.dtsi file, as the DSP1
processor sub-system is mostly common across all the variants
of the DRA7 SoC family.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Many OMAP2+ DTS are not using the defined constants to express
the GPIO polarity. Replace these so the DTS are easier to read.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SeeedStudio BeagleBone Green (BBG) is clone of the BeagleBone Black (BBB) minus
the HDMI port and addition of two Grove connectors (i2c2 and usart2).
This board can be identified by the 1A value after A335BNLT (BBB) in the at24 eeprom:
1A: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 1a 00 00 00 |.U3.A335BNLT....|]
http://beagleboard.org/greenhttp://www.seeedstudio.com/wiki/Beaglebone_green
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding child
sub-mailbox (IPC 3.x) nodes for the Beagle X15 EVM boards. This
is needed to enable communication with the respective remote
processors IPU1, IPU2, DSP1 and DSP2 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the DRA72 EVM board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, and DSP1 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the DRA7 EVM board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, DSP1 and DSP2 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the sub-mailbox nodes that are used to communicate between
MPU and the remote processors IPU1, IPU2 and DSP1. These match the
respective node definitions on DRA74x to maintain compatibility for
the equivalent remote processors. There is no DSP2 on DRA72x, and
so the corresponding sub-mailbox node is not added.
These sub-mailbox nodes are added to match the hard-coded mailbox
configuration used within the TI IPC 3.x software package. The
Dual-Cortex M4 IPU1 and IPU2 processor sub-systems are assumed to
be running in SMP-mode, and hence only a single sub-mailbox node
is added for each.
All these sub-mailbox nodes are left in disabled state, and should
be enabled (and modified if needed) as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the sub-mailbox nodes that are used to communicate between
MPU and the remote processors IPU1, IPU2, DSP1 and DSP2.
The sub-mailbox nodes utilize the System Mailbox instances 5 and 6.
These sub-mailbox nodes are added to match the hard-coded mailbox
configuration used within the TI IPC 3.x software package. The
Dual-Cortex M4 IPU1 and IPU2 processor sub-systems are assumed to
be running in SMP-mode, and hence only a single sub-mailbox node
is added for each.
All these sub-mailbox nodes are left in disabled state, and should
be enabled (and modified if needed) as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cleaned up the regulators on the wega board. Created a simple bus,
renamed the regulators according to the schematics and added missing
regulator on wega.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra7-evm has 2 gpio keys wired through TS_LCD_GPIO3, TS_LCD_GPIO4
which in turn connected to PCF8575 GPIO pcf_lcd: gpio@20 expander
pins 2 and 3.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra7-evm has 4 user gpio leds connected to PCF8575 GPIO pcf_lcd:
gpio@20 expander pins [4,5,6,7], so add corresponding DT nodes.
Do not enable any triggers by default as not all of them are proved
to work on -RT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds DT definition for CF8575 GPIO pcf_lcd: gpio@20
expander which is connected to i2c bus 1 and has slave address 0x20.
It allows to control:
- tc_lcd gpios, pins p0-p3
- user leds, pins p4-p7
- control LCD panel power, p15
PCF8575 GPIO pcf_lcd: gpio@20 expander supports interrupt controller
functionality and its INT line is connected to dra7 GPIO6.11 pin.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The analog audio setup consists of:
McASP3 <-> tlv320aic3104 codec
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DVDD is supplied via TPS77018DBVT fixed regulator from vdd_3v3
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses tlv320aic3106 codec connected to McASP3. The master clock
for the codec and McASP3 is coming from ATL2.
McASP3 is the master on the I2S bus.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPIO expander's p1 on i2c5 bus 0x26 address is used for selecting
between audio and VIN6 functionality. For VIN6 use an add on card is
needed while audio is present on the board itself.
Select the audio functionality over the VIN6 in the dts file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DVDD is supplied via TPS77018DBVT fixed regulator from evm_3v3
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses tlv320aic3106 codec connected to McASP3. The master clock
for the codec and McASP3 is coming from ATL2.
McASP3 is the master on the I2S bus.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This GPIO expander is used for controlling various muxes on the board.
By default select audio functionality over VIN6 by setting the P1
(vin6_sel_s0) pin to low.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
TPS77018DBVT is used to create 1.8V from avm_3v3_sw's 3.3V connected to
aic3106's DVDD.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the name for the supply as it is in the schematics since the same
supply is used for other peripherals than MMC2, like audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
