IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
msa6 and msa7 require no changes.
msa8 adds kma instruction and feature area.
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This patch implements consideration of the SPI_READY mode flag as
defined in spi.h. It extends the device tree bindings to support
the values defined by the reference manual for the DRCTL field.
Thus supporting edge-triggered and level-triggered bursts.
Signed-off-by: Leif Middelschulte <Leif.Middelschulte@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver sets appropriate DMA mask. Delete the "dma-mask" DT
property. See [1] for negative comments for this binding.
[1] https://lkml.org/lkml/2016/2/8/57
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There are various customizable parameters, so several variants for
this IP. A generic compatible like "denali,denali-nand-dt" is
useless. Moreover, there are multiple things wrong with this string.
(Refer to Rob's comment [1])
The "denali,denali-nand-dt" was added by Altera for the SOCFPGA port.
Replace it with a more specific string "altr,socfpga-denali-nand".
There are no users (in upstream) of the old compatible string.
The Denali IP on SOCFPGA incorporates the hardware ECC fixup engine.
So, this capability should be associated with the compatible.
[1] https://lkml.org/lkml/2016/12/1/450
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The old NAND bindings were not exactly describing the hardware topology
and were preventing definitions of several NAND chips under the same
NAND controller.
New bindings address these limitations and should be preferred over the
old ones for new SoCs/boards.
Old bindings are still supported for backward compatibility but are
marked deprecated in the doc.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add description of uinput module with a few examples.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add description of Cavium Octeon and ThunderX SOC device tree bindings.
CC: Ulf Hansson <ulf.hansson@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: devicetree@vger.kernel.org
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Steven J. Hill <steven.hill@cavium.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adds the device tree bindings description for Samsung S3C24XX
MMC/SD/SDIO controller, used as a connectivity interface with external
MMC, SD and SDIO storage mediums.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DTS properties are used instead of fixed data
because PHY settings can be different for different chips/boards.
Add description of new DLL PHY delays.
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add description for mediatek,hs200-cmd-int-delay
Add description for mediatek,hs400-cmd-int-delay
Add description for mediatek,hs400-cmd-resp-sel-rising
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is the other SD controller on the platform, which can be swapped
to the role of SD card host using pin muxing.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI controller found on Tegra186 in very similar to the controller
found on earlier generations of Tegra.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The list of compatible strings is somewhat difficult to read and extend.
Reformat it into a list to make it more easily extensible.
While at it, also remove the "plus one of the above" clause because it
isn't actually valid.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The introduction of the pci_remap_cfgspace() interface allows PCI host
controller drivers to map PCI config space through a dedicated kernel
interface. Current PCI host controller drivers use the devm_ioremap_*()
devres interfaces to map PCI configuration space regions so in order to
update them to the new pci_remap_cfgspace() mapping interface a new set of
devres interfaces should be implemented so that PCI host controller drivers
can make use of them.
Introduce two new functions in the PCI kernel layer and Devres
documentation:
- devm_pci_remap_cfgspace()
- devm_pci_remap_cfg_resource()
so that PCI host controller drivers can make use of them to map PCI
configuration space regions.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Middlebox firewall issues can potentially cause server's data being
blackholed after a successful 3WHS using TFO. Following are the related
reports from Apple:
https://www.nanog.org/sites/default/files/Paasch_Network_Support.pdf
Slide 31 identifies an issue where the client ACK to the server's data
sent during a TFO'd handshake is dropped.
C ---> syn-data ---> S
C <--- syn/ack ----- S
C (accept & write)
C <---- data ------- S
C ----- ACK -> X S
[retry and timeout]
https://www.ietf.org/proceedings/94/slides/slides-94-tcpm-13.pdf
Slide 5 shows a similar situation that the server's data gets dropped
after 3WHS.
C ---- syn-data ---> S
C <--- syn/ack ----- S
C ---- ack --------> S
S (accept & write)
C? X <- data ------ S
[retry and timeout]
This is the worst failure b/c the client can not detect such behavior to
mitigate the situation (such as disabling TFO). Failing to proceed, the
application (e.g., SSL library) may simply timeout and retry with TFO
again, and the process repeats indefinitely.
The proposed solution is to disable active TFO globally under the
following circumstances:
1. client side TFO socket detects out of order FIN
2. client side TFO socket receives out of order RST
We disable active side TFO globally for 1hr at first. Then if it
happens again, we disable it for 2h, then 4h, 8h, ...
And we reset the timeout to 1hr if a client side TFO sockets not opened
on loopback has successfully received data segs from server.
And we examine this condition during close().
The rational behind it is that when such firewall issue happens,
application running on the client should eventually close the socket as
it is not able to get the data it is expecting. Or application running
on the server should close the socket as it is not able to receive any
response from client.
In both cases, out of order FIN or RST will get received on the client
given that the firewall will not block them as no data are in those
frames.
And we want to disable active TFO globally as it helps if the middle box
is very close to the client and most of the connections are likely to
fail.
Also, add a debug sysctl:
tcp_fastopen_blackhole_detect_timeout_sec:
the initial timeout to use when firewall blackhole issue happens.
This can be set and read.
When setting it to 0, it means to disable the active disable logic.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards [1] leave the PHYs at an invalid state
during system power-up or reset thus causing unreliability
issues with the PHY which manifests as PHY not being detected
or link not functional. To fix this, these PHYs need to be RESET
via a GPIO connected to the PHY's RESET pin.
Some boards have a single GPIO controlling the PHY RESET pin of all
PHYs on the bus whereas some others have separate GPIOs controlling
individual PHY RESETs.
In both cases, the RESET de-assertion cannot be done in the PHY driver
as the PHY will not probe till its reset is de-asserted.
So do the RESET de-assertion in the MDIO bus driver.
[1] - am572x-idk, am571x-idk, a437x-idk
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistake in documentation
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TCA9554 is similar to the PCA9554. Update the DT binding docs.
Signed-off-by: Anders Darander <anders@chargestorm.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DM integrity block size can now be 512, 1k, 2k or 4k. Using larger
blocks reduces metadata handling overhead. The block size can be
configured at table load time using the "block_size:<value>" option;
where <value> is expressed in bytes (defult is still 512 bytes).
It is safe to use larger block sizes with DM integrity, because the
DM integrity journal makes sure that the whole block is updated
atomically even if the underlying device doesn't support atomic writes
of that size (e.g. 4k block ontop of a 512b device).
Depends-on: 2859323e ("block: fix blk_integrity_register to use template's interval_exp if not 0")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Some coding style changes.
Fix a bug that the array test_tag has insufficient size if the digest
size of internal has is bigger than the tag size.
The function __fls is undefined for zero argument, this patch fixes
undefined behavior if the user sets zero interleave_sectors.
Fix the limit of optional arguments to 8.
Don't allocate crypt_data on the stack to avoid a BUG with debug kernel.
Rename all optional argument names to have underscores rather than
dashes.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Although most of these kprobes patches are powerpc specific, there's a couple
that touch generic code (with Acks). At the moment there's one conflict with
acme's tree, but it's not too bad. Still just in case some other conflicts show
up, we've put these in a topic branch so another tree could merge some or all of
it if necessary.
We need a reference to the HPLL to calculate debounce cycles. If the
clocks property is not supplied in the GPIO node then the consumer
should deny any debounce requests.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove "ngpios" bindings definition as it is no more used in stm32 pinctrl
driver.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Document the device tree binding for the pin controllers found on the
Armada 37xx SoCs.
Update the binding documention of the xtal clk which is a subnode of this
syscon node.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
[Fixed gpios node]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Armada 370/XP devices can 'blink' GPIO lines with a configurable on
and off period. This can be modelled as a PWM.
However, there are only two sets of PWM configuration registers for
all the GPIO lines. This driver simply allows a single GPIO line per
GPIO chip of 32 lines to be used as a PWM. Attempts to use more return
EBUSY.
Due to the interleaving of registers it is not simple to separate the
PWM driver from the GPIO driver. Thus the GPIO driver has been
extended with a PWM driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
URL: https://patchwork.ozlabs.org/patch/427287/
URL: https://patchwork.ozlabs.org/patch/427295/
[Ralph Sennhauser:
* Port forward
* Merge PWM portion into gpio-mvebu.c
* Switch to atomic PWM API
* Add new compatible string marvell,armada-370-xp-gpio
* Update and merge documentation patch
* Update MAINTAINERS]
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow kprobes to be placed on ftrace _mcount() call sites. This optimization
avoids the use of a trap, by riding on ftrace infrastructure.
This depends on HAVE_DYNAMIC_FTRACE_WITH_REGS which depends on MPROFILE_KERNEL,
which is only currently enabled on powerpc64le with newer toolchains.
Based on the x86 code by Masami.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
update the list and remove 'in the future' statement,
since all still alive 64-bit architectures now do eBPF JIT.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both conflict were simple overlapping changes.
In the kaweth case, Eric Dumazet's skb_cow() bug fix overlapped the
conversion of the driver in net-next to use in-netdev stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the NFC pull request for 4.12. We have:
- Improvements for the pn533 command queue handling and device
registration order.
- Removal of platform data for the pn544 and st21nfca drivers.
- Additional device tree options to support more trf7970a hardware options.
- Support for Sony's RC-S380P through the port100 driver.
- Removal of the obsolte nfcwilink driver.
- Headers inclusion cleanups (miscdevice.h, unaligned.h) for many drivers.
-----BEGIN PGP SIGNATURE-----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=Zy1M
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.12 pull request
This is the NFC pull request for 4.12. We have:
- Improvements for the pn533 command queue handling and device
registration order.
- Removal of platform data for the pn544 and st21nfca drivers.
- Additional device tree options to support more trf7970a hardware options.
- Support for Sony's RC-S380P through the port100 driver.
- Removal of the obsolte nfcwilink driver.
- Headers inclusion cleanups (miscdevice.h, unaligned.h) for many drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds DT binding documentation for Odroid XU3/4
sound subsystem.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Constants used for tuning are generally a bad idea, especially as hardware
changes over time. Replace the constant 2 jiffies with sysctl variable
netdev_budget_usecs to enable sysadmins to tune the softirq processing.
Also document the variable.
For example, a very fast machine might tune this to 1000 microseconds,
while my regression testing 486DX-25 needs it to be 4000 microseconds on
a nearly idle network to prevent time_squeeze from being incremented.
Version 2: changed jiffies to microseconds for predictable units.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the chip the IMON signal is a full 24-bits however normally only
some of the bits will be sent over the bus. The chip provides a field
to select which bits of the IMON will be sent back, this is the only
feedback signal that has this feature.
Add an additional entry to the cirrus,imon device tree property to
allow the IMON scale parameter to be passed.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qqfj
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.11-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Sorry this is so late. It's been in -next for over a week, but I
forgot to send it on until now.
A single fix to the DT binding of the HiSilicon PCIe host support"
* tag 'pci-v4.11-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: hisi: Fix DT binding (hisi-pcie-almost-ecam)
We actually can't allow the missing of the regualor name, thus update
the binding doc to make regulator-name property to be required.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow setting AUS mode for a display from the device tree. Use an
optional boolean property. AUS mode can be set only on imx21 and
compatible chipsets.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Document the devicetree bindings for Mediatek random number
generator which could be found on MT7623 SoC or other similar
Mediatek SoCs.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Guests that are heavy on futexes end up IPI'ing each other a lot. That
can lead to significant slowdowns and latency increase for those guests
when running within KVM.
If only a single guest is needed on a host, we have a lot of spare host
CPU time we can throw at the problem. Modern CPUs implement a feature
called "MWAIT" which allows guests to wake up sleeping remote CPUs without
an IPI - thus without an exit - at the expense of never going out of guest
context.
The decision whether this is something sensible to use should be up to the
VM admin, so to user space. We can however allow MWAIT execution on systems
that support it properly hardware wise.
This patch adds a CAP to user space and a KVM cpuid leaf to indicate
availability of native MWAIT execution. With that enabled, the worst a
guest can do is waste as many cycles as a "jmp ." would do, so it's not
a privilege problem.
We consciously do *not* expose the feature in our CPUID bitmap, as most
people will want to benefit from sleeping vCPUs to allow for over commit.
Reported-by: "Gabriel L. Somlo" <gsomlo@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
[agraf: fix amd, change commit message]
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Documentation/DocBook/Makefile hard codes the prefixed path to which you
can install the built man pages (/usr/local prefix). That's unfortunate
since the user may want to install to another prefix or location (for
example, a distribution packaging the man pages may want to install to a
random temporary location in the build process).
Be flexible and allow the prefixed path to which we install man pages to be
changed with the INSTALL_MAN_PATH environment variable (and use the same
default as other similar variables like INSTALL_HDR_PATH).
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
