IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The USE_SPI_DMA macro name suggests that it could be set to 1 to
control whether or not SPI DMA should be used. However, that's not
what it does. If set to 1, it'll set the SPI messages'
"is_dma_mapped" flag to true, even though the tx/rx buffers aren't
actually DMA mapped by the driver. In other words, setting this flag
to 1 will break the driver.
Best to clean up this confusion by removing the macro altogether.
There is no need to explicitly initialize "is_dma_mapped" because the
message is cleared to zero anyhow, so "is_dma_mapped" is set to false
by default.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211207002453.3193737-1-davidm@egauge.net
The messages appears to have been copied from wilc_get_mac_address and
says "get" when it should say "set".
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211206232709.3192856-2-davidm@egauge.net
This eliminates warning message:
SPI driver WILC_SPI has no spi_device_id for microchip,wilc1000
and makes device-tree autoloading work.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211202045001.2901903-1-davidm@egauge.net
First set of patches for v5.17. The biggest change is the iwlmei
driver for Intel's AMT devices. Also now WCN6855 support in ath11k
should be usable.
Major changes:
ath10k
* fetch (pre-)calibration data via nvmem subsystem
ath11k
* enable 802.11 power save mode in station mode for qca6390 and wcn6855
* trace log support
* proper board file detection for WCN6855 based on PCI ids
* BSS color change support
rtw88
* add debugfs file to force lowest basic rate
* add quirk to disable PCI ASPM on HP 250 G7 Notebook PC
mwifiex
* add quirk to disable deep sleep with certain hardware revision in
Surface Book 2 devices
iwlwifi
* add iwlmei driver for co-operating with Intel's Active Management
Technology (AMT) devices
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmGvclcRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZtK6wgAoOoT83JKMreXlXXhVegqlJbC3HyElF5r
DJlpDDJkJUT9airol2nd0yFfP+5WFyQPrt5shsQmqz43U4jlgfFpFXZIjQufK+gn
VAGvVGfsanRXEFlsVgFZeSZvAEyEyNSggxADC03Ky0xtiCGc89r2o71jD3HA/ZzO
1X8gbKH7YLWj4G/GQkrKsvIAwzoZXT7nwQSdW73M8QVzk4OSNhLBLdiqKYq0yViM
7Ea2Vj27hiyk/RXNUZHy+bKa8vKN5sA91VHJ836aPZBQ4OLotGzF3AgHfgIhIpdr
hI4BVJbngpjQho1EkCnZZuISPes0YQWJB5hK5xpL98yuIL4wyJRfeQ==
=I8Dj
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
First set of patches for v5.17. The biggest change is the iwlmei
driver for Intel's AMT devices. Also now WCN6855 support in ath11k
should be usable.
Major changes:
ath10k
* fetch (pre-)calibration data via nvmem subsystem
ath11k
* enable 802.11 power save mode in station mode for qca6390 and wcn6855
* trace log support
* proper board file detection for WCN6855 based on PCI ids
* BSS color change support
rtw88
* add debugfs file to force lowest basic rate
* add quirk to disable PCI ASPM on HP 250 G7 Notebook PC
mwifiex
* add quirk to disable deep sleep with certain hardware revision in
Surface Book 2 devices
iwlwifi
* add iwlmei driver for co-operating with Intel's Active Management
Technology (AMT) devices
* tag 'wireless-drivers-next-2021-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (87 commits)
iwlwifi: mei: fix linking when tracing is not enabled
rtlwifi: rtl8192de: Style clean-ups
mwl8k: Use named struct for memcpy() region
intersil: Use struct_group() for memcpy() region
libertas_tf: Use struct_group() for memcpy() region
libertas: Use struct_group() for memcpy() region
wlcore: no need to initialise statics to false
rsi: Fix out-of-bounds read in rsi_read_pkt()
rsi: Fix use-after-free in rsi_rx_done_handler()
brcmfmac: Configure keep-alive packet on suspend
wilc1000: remove '-Wunused-but-set-variable' warning in chip_wakeup()
iwlwifi: mvm: read the rfkill state and feed it to iwlmei
iwlwifi: mvm: add vendor commands needed for iwlmei
iwlwifi: integrate with iwlmei
iwlwifi: mei: add debugfs hooks
iwlwifi: mei: add the driver to allow cooperation with CSME
mei: bus: add client dma interface
mwifiex: Ignore BTCOEX events from the 88W8897 firmware
mwifiex: Ensure the version string from the firmware is 0-terminated
mwifiex: Add quirk to disable deep sleep with certain hardware revision
...
====================
Link: https://lore.kernel.org/r/20211207144211.A9949C341C1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unused variables to avoid the below warnings:
drivers/net/wireless/microchip/wilc1000/wlan.c: In function 'chip_wakeup':
>> drivers/net/wireless/microchip/wilc1000/wlan.c:620:34: warning: variable 'to_host_from_fw_bit' set but not used [-Wunused-but-set-variable]
620 | u32 to_host_from_fw_reg, to_host_from_fw_bit;
| ^~~~~~~~~~~~~~~~~~~
>> drivers/net/wireless/microchip/wilc1000/wlan.c:620:13: warning: variable 'to_host_from_fw_reg' set but not used [-Wunused-but-set-variable]
620 | u32 to_host_from_fw_reg, to_host_from_fw_bit;
| ^~~~~~~~~~~~~~~~~~~
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115102809.1408267-1-ajay.kathat@microchip.com
wilc_set_mac_address() calls IO routines which don't guarantee
the pointer won't be written to. Make a copy.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-13-kuba@kernel.org
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/0855d51423578ad019c0264dad3fe47a2e8af9c7.1633849511.git.christophe.jaillet@wanadoo.fr
Increase the WID config packet response timeout to have extra wait time for
host to receive the response message from firmware. Sometimes the WID
config response was timed out because of host interrupt latency.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-12-ajay.kathat@microchip.com
Instead of using double read for the same register, use the write register
command after the read command.
The correct sequence is to use the read value in write command instead of
reading the same register again.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-11-ajay.kathat@microchip.com
Add 'initialized' variable check before adding net/mgmt packet to TX queue
as safety check before passing the commands to the firmware.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-10-ajay.kathat@microchip.com
Add the chip reset command to initialize the WILC chip before downloading
the firmware. Also, put the chip in wake-up mode so it is ready to receive
the firmware binary from the host.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-9-ajay.kathat@microchip.com
During WILC chip wake-up sequence, the clockless status register sometimes
reports failure even when the actual status is successful. So, for the
clockless register, remove the incorrect error status reporting during the
read and write command API's.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-8-ajay.kathat@microchip.com
For SPI bus, the register read fails after read/write to the clockless
register during chip wakeup sequence. Add workaround to send CMD_RESET
command during chip wake-up sequence to overcome the issue.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-7-ajay.kathat@microchip.com
Add reset/terminate/repeat command for SPI module. In case of SPI commands
failure, the host should issue a RESET command to WILC chip to recover
from any temporary bus error.
For now, the new command support is added and later the SPI read/write
API's would be modified to make use of these commands for retry mechanism
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-6-ajay.kathat@microchip.com
Use the correct sequence to configure clockless registers for chip wake-up.
The following sequence is expected from WILC chip for wakeup:
- set wakeup bit in wakeup_reg register
- after setting the wakeup bit, read back the clock status bit for wakeup
complete.
For SDIO/SPI modules, the wakeup sequence is the same except uses different
register values so refactored the code to use common function for both
SDIO/SPI bus.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-5-ajay.kathat@microchip.com
Add new WID(WID_WOWLAN_TRIGGER) to send wake_enable information to firmware.
In 'set_wakeup' cfg80211_ops callback, the enable information was not
passed to firmware which is required to handle WOWLan trigger notification
from firmware.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-4-ajay.kathat@microchip.com
When the BSS reference holds a valid reference, it is not freed. The 'if'
condition is wrong. Instead of the 'if (bss)' check, the 'if (!bss)' check
is used.
The issue is solved by removing the unnecessary 'if' check because
cfg80211_put_bss() already performs the NULL validation.
Fixes: 6cd4fa5ab691 ("staging: wilc1000: make use of cfg80211_inform_bss_frame()")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-3-ajay.kathat@microchip.com
Move initialization & deinitialization of 'deinit_lock' mutex lock inside
wlan_init_locks() & wlan_deinit_locks() API's respectively alongside other
locks. After the movement, the client count variable(client_count) which is
used for lock init/deinit is removed.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-2-ajay.kathat@microchip.com
Move static "isinit" variable to wilc_spi structure to allow multiple
WILC1000 devices per machine.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210828151346.3012697-1-davidm@egauge.net
Use goto labels on error path for probe functions. This makes code easier
to read. With this introduce also netdev_cleanup and call it where
necessary.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210806081229.721731-2-claudiu.beznea@microchip.com
Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
requires an "rtc" clock name.
drivers/net/wireless/microchip/wilc1000/sdio.c is using "rtc" clock name
as well. Comply with the binding in wilc1000/spi.c too.
Fixes: 854d66df74ae ("staging: wilc1000: look for rtc_clk clock in spi mode")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210428025445.81953-1-tudor.ambarus@microchip.com
If the loop fails, the "while(trials--) {" loop will exit with "trials"
set to -1. The test for that expects it to end with "trials" set to 0
so the warning message will not be printed.
Fix this by changing from a post-op to a pre-op. This does mean that
we only make 99 attempts instead of 100 but that's okay.
Fixes: f135a1571a05 ("wilc1000: Support chip sleep over SPI")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YFS5gx/gi70zlIaO@mwanda
Linux network drivers normally disallow changing the MAC address when
the interface is up. This driver has been different in that it allows
to change the MAC address *only* when it's up. This patch brings
wilc1000 behavior more in line with other network drivers. We could
have replaced wilc_set_mac_addr() with eth_mac_addr() but that would
break existing documentation on how to change the MAC address.
Likewise, return -EADDRNOTAVAIL (not -EINVAL) when the specified MAC
address is invalid or unavailable.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210303194846.1823596-1-davidm@egauge.net
The driver so far has always disabled CRC protection. This means any
data corruption that occurrs during the SPI transfers could go
undetected. This patch adds module parameters enable_crc7 and
enable_crc16 to selectively turn on CRC7 (for command transfers) and
CRC16 (for data transfers), respectively.
The default configuration remains unchanged, with both CRC7 and CRC16
off.
The performance impact of CRC was measured by running ttcp -t four
times in a row on a SAMA5 device:
CRC7 CRC16 Throughput: Standard deviation:
---- ----- ----------- -------------------
off off 1720 +/- 48 KB/s
on off 1658 +/- 58 KB/s
on on 1579 +/- 84 KB/s
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210227172818.1711071-4-davidm@egauge.net
After a DMA write to the WILC chip, check for and report any errors.
This is based on code from the wilc driver in the linux-at91
repository.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210227172818.1711071-3-davidm@egauge.net
The WILC1000 protocol control register has bits for enabling the CRCs
(CRC7 for commands and CRC16 for data) and to set the data packet
size. Define symbolic names for those so the code is more easily
understood.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210227172818.1711071-2-davidm@egauge.net
For CMD_SINGLE_READ and CMD_INTERNAL_READ, WILC may insert one or more
zero bytes between the command response and the DATA Start tag (0xf3).
This behavior appears to be undocumented in "ATWILC1000 USER GUIDE"
(https://tinyurl.com/4hhshdts) but we have observed 1-4 zero bytes
when the SPI bus operates at 48MHz and none when it operates at 1MHz.
This code is derived from the equivalent code of the wilc driver in
the linux-at91 repository.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210227172818.1711071-1-davidm@egauge.net
Use same cookie for request_threaded_irq() & free_irq() to properly free
IRQ during module unload. free_irq() already uses *wilc* handler so the
changes are required for request_threaded_irq().
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210225042302.17048-1-ajay.kathat@microchip.com
Write the value instead of reading it twice.
Fixes: c5c77ba18ea6 ("staging: wilc1000: Add SDIO/SPI 802.11 driver")
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210224163706.519658-1-marcus.folkesson@gmail.com
chip_allow_sleep() only supported wakeup via SDIO, which made the
driver unusable over SPI. This code is a straight forward port from
the driver in the linux-at91 repository.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210224033317.1507603-1-davidm@egauge.net
ac_classify() expects a struct sk_buff* as its second argument, which is
a member of struct tx_complete_data. priv happens to be a pointer to
struct tx_complete_data, so passing it directly to ac_classify() leads
to wrong behaviour and occasional panics.
Since there is only one caller of wilc_wlan_txq_add_net_pkt and it
already knows the type behind this pointer, and the structure is already
in the header file, change the function signature to use the real type
instead of void* in order to prevent confusion.
Signed-off-by: Vsevolod Kozlov <zaba@mm.st>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YCQomJ1mO5BLxYOT@Vsevolods-Mini.lan
First set of patches for v5.12. A smaller pull request this time,
biggest feature being a better key handling for ath9k. And of course
the usual fixes and cleanups all over.
Major changes:
ath9k
* more robust encryption key cache management
brcmfmac
* support BCM4365E with 43666 ChipCommon chip ID
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJgHW7nAAoJEG4XJFUm622bgd0IAKtEBcjfqnR2wW7Rt6Ah/Uch
vInrZ+5YOhjamoCvZHhTwdvUEmuRYJBT8ZqfO5x3X0GlIaJe1PlJhlvOs/9PkQ9G
eMSFcy1D/uSb3KoRRLq8lNaAy7NAyajg11IhRAeQFLeBkZgI43PGq6j7sbYCerah
87trNNlHagio9p4q9FGXVtJ2cJGQdNHM8jn4dw5Uue45YArkhj6VBh3EZl9dqV+F
XmxK+qvIcK1KPzw6nZ/0dGf8B6dnXaljn0cAzAo8QPSaZI+jozY52y3XdoKVqYRF
ekqDra4Xl/uKVZR1vb2jE5T/NtmzZI63uifndL6esEjwJMrrkRy9+alHwIxt2rU=
=KZD7
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-02-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.12
First set of patches for v5.12. A smaller pull request this time,
biggest feature being a better key handling for ath9k. And of course
the usual fixes and cleanups all over.
Major changes:
ath9k
* more robust encryption key cache management
brcmfmac
* support BCM4365E with 43666 ChipCommon chip ID
* tag 'wireless-drivers-next-2021-02-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (35 commits)
iwl4965: do not process non-QOS frames on txq->sched_retry path
mt7601u: process tx URBs with status EPROTO properly
wlcore: Fix command execute failure 19 for wl12xx
mt7601u: use ieee80211_rx_list to pass frames to the network stack as a batch
rtw88: 8723de: adjust the LTR setting
rtlwifi: rtl8821ae: fix bool comparison in expressions
rtlwifi: rtl8192se: fix bool comparison in expressions
rtlwifi: rtl8188ee: fix bool comparison in expressions
rtlwifi: rtl8192c-common: fix bool comparison in expressions
rtlwifi: rtl_pci: fix bool comparison in expressions
wlcore: Downgrade exceeded max RX BA sessions to debug
wilc1000: use flexible-array member instead of zero-length array
brcmfmac: clear EAP/association status bits on linkdown events
brcmfmac: Delete useless kfree code
qtnfmac_pcie: Use module_pci_driver
mt7601u: check the status of device in calibration
mt7601u: process URBs in status EPROTO properly
brcmfmac: support BCM4365E with 43666 ChipCommon chip ID
wilc1000: fix spelling mistake in Kconfig "devision" -> "division"
mwifiex: pcie: Drop bogus __refdata annotation
...
====================
Link: https://lore.kernel.org/r/20210205161901.C7F83C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We used to not require anything in terms of registering netdevs
with cfg80211, using a netdev notifier instead. However, in the
next patch reducing RTNL locking, this causes big problems, and
the simplest way is to just require drivers to do things better.
Change the registration/unregistration semantics to require the
drivers to call cfg80211_(un)register_netdevice() when this is
happening due to a cfg80211 request, i.e. add_virtual_intf() or
del_virtual_intf() (or if it somehow has to happen in any other
cfg80211 callback).
Otherwise, in other contexts, drivers may continue to use the
normal netdev (un)registration functions as usual.
Internally, we still use the netdev notifier and track (by the
new wdev->registered bool) if the wdev had already been added
to cfg80211 or not.
Link: https://lore.kernel.org/r/20210122161942.cf2f4b65e4e9.Ida8234e50da13eb675b557bac52a713ad4eddf71@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Added retry mechanism to ensure VMM enable bit is set during the
block transfer of data between host and WILC FW.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201208103739.28597-1-ajay.kathat@microchip.com
The assignment to pointer vif is redundant as the assigned value
is never read, hence it can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201203174316.1071446-1-colin.king@canonical.com
Added multiple queues[BK,BE,VI,VO] to handle different priority data
packets. Before adding a packet to the queue, checked its priority from
the header, and then add to the suitable queue. The limit for each queue
is maintained separately. Also while passing the packets to the firmware
via VMM take care to select data packets based on priority and available
space.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201125114059.10006-6-ajay.kathat@microchip.com
Before returing from wilc_wlan_txq_add_mgmt_pkt() invoke tx_complete_fn()
callback to free up allocated memory for failure case.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201125114059.10006-4-ajay.kathat@microchip.com
Before returing from wilc_wlan_txq_add_net_pkt() invoke tx_complete_fn()
callback to free up allocated memory for failure cases.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201125114059.10006-3-ajay.kathat@microchip.com
The wilc_wfi_init_mon_int() forgets to clean up resource when
register_netdevice() failed. Add the missed call to fix it.
And the return value of netdev_priv can't be NULL, so remove
the unnecessary error handling.
Fixes: 588713006ea4 ("staging: wilc1000: avoid the use of 'wilc_wfi_mon' static variable")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Huang Guobin <huangguobin4@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200917123019.206382-1-huangguobin4@huawei.com
When devm_clk_get() returns -EPROBE_DEFER, spi_priv
should be freed just like when wilc_cfg80211_init()
fails.
Fixes: 854d66df74aed ("staging: wilc1000: look for rtc_clk clock in spi mode")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200820055256.24333-1-dinghao.liu@zju.edu.cn
